Yellow Trolly - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyYellow Trolly - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, rolling stock , yellow - trolley, bn class trolley, trolly, trolley

NWT1 - Jenny - Trolly Trailer Built by Puffing Billy Volunteers named after PBPS member John Thompson's wife Jenny built on the frame of an old casey trolly . previous no. NWTC-1 Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - Trolly TrailerNWT1 - Jenny - Trolly Trailer made of Steel NWT1 - Jennypuffing billy, trolley trailer, trolly, trolley

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

NG1 - Sarge - Trolly Trailer Named Sarge as it originally had three safety chevrons on the back that resembled Sargeant's stripes.Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - Trolly TrailerNG1 - Sarge - Trolly Trailer made of Steel and MetalNG1 - Sargepuffing billy railway, pbr, rolling stock , ng1 - sarge - trolley trailer, trolley, trolly

Ganger's Trolly Turntable When a railway gangers trolly was working between railway stations, occasionally it was required for the line to be clear for trains to operate. Many trollys were too heavy to physically lift off the track, so a turntable was needed. These were provided at designated locations, and in some cases the trolly had a turntable on board. The turntable would be placed on the rails and the trolley driven onto it. The turntable would then be rotated 90 degrees by human power and the trolley pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location. Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolly TurntableGanger's Trolly Turntable made of wood with wrought iron fittings puffing billy, ganger's trolley turntable, trolley, trolly

Red Trolley - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyRed Trolley - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, red - trolley, bn class trolley, trolley, trolly

NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolley - a KS series Section Car oftern called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Trolly 9 was built for the State Electricity Commission of Victoria for use on their metre gauge railway of Yallourn. It was sold to a preservation group at Walhalla and regauged to 2 foot 6 inch. It came to the Puffing Billy Railway in the early 1980s.Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by the State Electricity Commission of Victoria for use on their 900mm gauge railway of Yallourn. And then at Walhalla Railway where it was regauged to 2 foot 6 inchMotorised small rectangular trolly made of wood and wrought iron - currently stored dismantled Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 9puffing billy, puffing billy museum, trolley, narrow gauge, 2'6" gauge, victorian railways, state electricity commission of victoria - yallourn., trolly

Built by the Victorian Railways it was originally used on the postal motor service on the Wangaratta to Whitfield narrow gauge line, for the cartage of small goods. it was part of the consist that operated the last service on that line in 1953. In 1960, it was purchased from the Victorian Railways, restored and taken to Belgrave to assist in the restoration of the Puffing Billy Railway. In the mid 1960's it was classified "NGA 1". In the 1970's, it was withdrawn from regular use and dismantled.Historic - Victorian Railways narrow gauge - trolly tralier Wangaratta to Whitfield narrow gauge lineTrolly Trailer Made of metal - frames and wheels only puffing billy, victorian railways, whitfield trolley trailer, narrow gauge rolling stock, postal motor, trolly

It was constructed on a former Victorian Railways NKS type underframe and powered by a single cylinder, 500 cc B.S.A. side valve motorcycle engine to drive axle by roller chains through an 'Ariel Square Four' gearbox and has traveled on all four 2'6" narrow gauge lines that operated in the state of Victoria.Historic - Narrow Gauge Railway - Track Patrol Vehicle used by Puffing Billy Preservation Society and made from parts of a Victorian Railways track patrol vehicleMotorised small rectangular trolly made of wood and wrought iron ME1 P.B.P.S Track Construction Departmentme 1, trolley, victorian railway, 2'6" gauge, puffing billy, trolly

NKS Trolley Motor Transporting Box A wooden box used for transporting the engines of the Gangers trolleys between the line in use and the Workshops at Spotswood. Engines were often changed over due to mechanical failure or being required for a service. Rather than send the complete trolley in for work, the engine was removed and transported. These boxes may have arrived at a location with an engine in it, to replace the one returning to the Workshops, cutting down the time that the trolley may have been out of use. Historic - Victorian Railways - Permanent Way and Works - track equipment - NKS Trolly Motor Transporting BoxNKS Trolly Motor Transporting Box - two boxes made of timber with wrought iron fittings puffing billy, nks trolley motor transporting box, trolly, trolley

NVW 1 - Track Patrol vehicle Rebuilt by Puffing Billy Volunteers given Number NVW 1 as it was built with a (VW) Volks wagon engine Was originally a trolley on the Australian Portland Cement Ltd at Fyansford Victoria Obtained by the Puffing Billy Preservation Society around 1968. Originally 3'6" ( 1067mm) before being rebuilt. Historic - Puffing Billy Track patrol - Rail Vehicle - NVW 1 NVW 1 - Track Patrol vehicle made of metal & steel with canvas vinyl blindsNVW 1puffing billy, nvw 1, trolley, trolly

This type of trolly is known to date from prior to 1910 and were in use before petrol engines were used to transport workmen along the railway lines. The exhibit was located at Colac in 1961, after being used on the Colac to Beech Forest and Crowes narrow gauge railway. This type of trolly was built in two versions; one for the Victorian Railways broad gauge lines, and one for the narrow gauge lines.Historic - Victorian Railways narrow gauge - track work vehicle. This vehicle was used in the days before petrol engines were used to drive vehicles transporting workmen along the railway line.C2N Type Trolly - Victorian Railways Gauge 2'6" Trolly Has a flat piece of wood that you would stand on with four metal wheels, one under each corner.c2n, trolley, victorian railways, hand power, narrow gauge, puffing billy, trolly

Newspaper clipping contained within Reg. Item 2526, page 10, titled "From Horse Tram to Trolly Bus" (mis-spelt word) recording the history of the cable trams in Melbourne, the formation of the company, prohibition of steam locomotives, costs, mechanical problems, Council objections, rails, visit of Mr. Hallide, court actions, King St. track, take over by the MMTB and that "conversion war still rages" - and perhaps trolley buses. Has been cut out from a sheet and pasted into the book. Written prior to final conversion in Melbourne in 1940. Note Item Not formally Numbered.melbourne, cable trams, tramways

NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolly - a KS series Section Car oftern called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by Puffing Billy Preservation SocietyMotorised small rectangular trolly made of wood and wrought iron Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 8puffing billy, victorian railways, trolley, narrow gauge, 2'6" gauge, kasey, trolly

NKS 5 - NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolly - a KS series Section Car often called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by Puffing Billy Preservation SocietyMotorised small rectangular trolly made of wood and wrought iron Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 5trolley, nks5, puffing billy, victorian railways, narrow gauge, 2'6" gauge, trolly

V.R Fuel Can for Trolley - Victorian Railways Fuel Can for Trolly Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949.Historic - Victorian Railways - Permanent Way and Works - track equipment - V.R Fuel Can for TrolleyV.R Fuel Can for Trolly - Metal Fuel TinMotor Spirit Highly Flammable V.R 8 ?puffing billy, victorian railways, fuel can, trolley, trolly

Photograph depicting Peter Ratley aka Peter Searle and his Victorian Navy colleagues standing in front of a tall building with two torpedoes on a trolly in front of them.Photograph depicting Peter Ratley aka Peter Searle and his Victorian Navy colleagues standing in front of a tall building with two torpedoes on a trolly in front of them.X over Peter Ratley aka Peter Searlevictorian navy victorian naval forces torpedoes

Group of men pushing trolleys with boxes of Pomonal apples at Stawell Railway Goods Shed. In the background are more men overseeing the loading of fruit. In the 1930's many cases of apples were exported overseas. The original photograph is held at the public records office. Y.P.R.S. series no. 3457 no 113. The Stawell Historical Society had permission to copy this photograph from Northern Grampians Shire Commissioners. Group of men in a shed pushing hand trollies with four boxes of apples loaded on each trolly.stawell

Man dressed as a Clown (Zag) pulling a trolly with another clown (Zig).concongella school parade

East BeachColoured photograph of Griffith Island with Norfolk Island Pines and remains of trolly walleast beach, battery hill, reef, training walls, norfolk pines

Group of people dressed as hippie's One Pulling a bathtup on a trolly, with pipe band in background.concongella school parade

Aunde / Norwellan Textiles North Western Woolen Mills became Norwellan Textiles then AUNDEColour landscape photo: Male worker inserting / extracting blanket into milling machine. Trolly with blanketsMillingindustry, aunde

TROVE : Evening News (Sydney, NSW : 1869 - 1931), Thursday 11 October 1928, page 13. NEW COMPANIES The following new companies were registered this afternoon :- Australian Essential Oils Ltd : Nominal capital. £50,000, in 93.000 ordinary and 7,000 deferred shares at 10/-. to engage in business of distillers, manufacturers of, and dealers in oils from vegetables and other sub-stances, chemists etc. First directors: N. H.B.Keynor, R.K.Allport, E.M Humphries, and H. James. Head office Sydney. TROVE : Government Gazette of the State of New South Wales (Sydney, NSW : 1901 - 2001), Friday 26 July 1968 (No.89), page 3028 IN the matter of the Companies Act, 1961-1966, and in the matter of AUSTRALIAN ESSENTIAL OILS LTD (Receiver and Manager Appointed).—Roy Leslie Pegler, Receiver and Manager of Australian Essential Oils Ltd (Receiver and Manager Appointed)„ appointed by debenture holders on the 11 th July, 1966, hereby gives notice that any debenture holders and others having any claim against or to Australian Essential Oils Ltd (Receiver and Manager Appointed) are required to send particulars of their debenture or claim to the Receiver, Roy Leslie Pegler, at c.o. Messrs Pegler, Ellis & Co., Chartered Accountants, 235-7 Elizabeth Street, Sydney, N.S.W., on or before the 27th September, 1968, at the expiration of which time the Receiver and Manager will distribute the assets of the said Company to the persons and/or companies entitled, having regard only to the claims of which he then has notice.—Dated 24th July, 1968. PEGLER, ELLIS & CO., Chartered Accountants, 235-7 Elizabeth Street, Sydney, N.S.W. 8744—$5 White cardboard box printed in dark green with a round blue and white sticker on one side, containing a cream paper leaflet printed in dark green, wrapped around a greaseproof paper wrapped rectangular cake of translucent brown soap with impressed text on one side.Impressed on one side of the cake of soap ' A PRODUCT OF AUSTRALIAN ESSENTIAL OILS LTD SYDNEY'. On reverse of soap impressed 'TI-TROL ANTISEPTIC TOU\ILET SOAP'. Printed on the box 'TI-TROL ANTISEPTIC AND GERMICIDAL TOILET SOAP. Printed Leaflet wrapped around cake of soap 'Germicide TI-TROL Antiseptic, Toilet Soap ELEVEN TIMES MORE POWERFUL THAN CARBOLIC. NON IRRITANT ………NON POISONOUS. “Ti –Trol” GERMICIDAL ANTISEPTIC SOAP is the most modern of all toilet soap …..Distilled and manufactured by Australian Essential Oils Ltd., the pioneers of Tea-Tree Oil Industry in Australia, and manufacturers of that famous antiseptic solution Melasol. It has taken years of patient research, of test, trial and experiment to reach the pinnacle of perfection which Ti-Trol Soap is now offering to the public. Ti-Trol is a hand-made glycerine base soap in which only the finest ingredients are used. One of its most attractive features is that it contains a full three per cent. of “Ti-trol”. In medical and clinical practice, both in Australia and abroad, Ti Trol has given remarkable results…particularly in its cleansing properties: its soothing HEALING action on dirty and inflamed septic wounds. By incorporating Ti-Trol in a glycerine base soap, experts are agreed that the result….. Ti-Trol soap is unequalled-anywhere- for its soft soothing healing and germicidal properties. Ti-Trol soap is non-irritant and non-poisonous and can be used on the tenderest skins…babies’ or the most delicate peach-bloom complexions, with most excellent results. . PRODUCT OF A SOAP MAKER OF INTERNATIONAL EXPERIENCE Australian Essential Oils Ltd., have been fortunate in procuring the services of a soap-maker of International experience and world-wide knowledge of Soap Production, whose genius has produced Ti-Trol, and whose uncanny sense of blending has made Ti-Trol the most famous of all Germicidal Toilet Soaps. Ti-Trol is non-irritant and non-poisonous and has been proved by medical and specialised authorities top\ possess great healing and cleansing properties. It is a powerful Germicide and antiseptic….ELEVEN TIMES QUICKER THAN PURE CARBOLIC. . DANDRUFF CAN’T LIVE WITH Ti-Trol. Dandruff ......that horrible “give away” which many men and women suffer from…..can easily be dispelled by using Ti-Trol Soap this way : Rub a little Olive Oil into the scalp before retiring at night, and the following morning wash your head thoroughly with Ti-Trol Soap, allowing the lather to remain on the scalp for about a minute and a half. Then rinse the hair thoroughly in warm water. .WASH BRUSHES AND COMBS WITH Ti-Trol SOAP When you’ve done this and dried your hair, wash all your brushes and combs in a strong, soapy solution made with Ti-Trol Soap, and then carefully sponge the inside of the hat bands with a flannel or cloth moistened with this soapy solution. Follow these directions and you’ll never need to fear dandruff. .Ti-Trol…WONDERFUL HEALER OF CUTS. SORES, WOUNDS, ETC. There never was a more patent healer of CUTS, SORES, WOUNDS, ABRASIONS AND SEPTIC SORES than Ti-Trol… Here’s how to use it : Wash the affected parts with a fairly strong Ti-Trol soapy solution made with warm water, and then apply with lint soaked with Melasol, which is the miscible form of Ti-Trol (Melasol is obtainable at all chemists and stores everywhere). . Ti-Trol SOAP……..A DEODORANT, A BEAUTIFIER……a safeguard for tender skins Ti-Trol Soap, because of its delicate, pungent, aroma and antiseptic properties, is unequalled as a deodorant, and is never failing when used for this purpose. Ti-Trol Soap can be used on the tenderest skins, and even baby’s skin, with greatest safety. It’s delightful fragrance will give added pleasure to your toilet. . DO NOT WASTE Ti-Trol Soap is too valuable to waste. Therefore, use it carefully. Do not leave it in the water. To obtain greatest economy it is preferable to use a face cloth when using Ti-Trol Soap. For health, for the most economical means of insuring against disease, use Ti-Trol Ointment…..for cuts, bruises etc. Ti-Trol….for boils, cuts, sores, abrasions and septic conditions. MELASOL…..for Tinea, Mouth Wash and as a Dentifice. . All are products containing Ti-Trol, distilled and provided by Australian Essential Oils Ltd. 18 Loftus Street, Sydney. N.S.W.'. tea tree oil, soap, glycerine, antisptic, germicide

Colour Photograph showing bushland opposite the mines current entrance, there were signs of trolly rails in 2000mining, gold mining

also Black and white copy 10 x 12|also Sepia toned copy 10 x 15Sepia toned small format postcard of the steamer Gippsland leaving Kalimna Jetty, Gippsland Lakes Victoria, also showing boat ramps beside jetty, three rowing boats moored at lower landing, persons pushing trolly along jetty, Navigation light on jetty, rustic jetty and small boat in background. Lakes Entrance VictoriaKalimna Jetty Gippsland Lakesjetties, waterways, topography