Hand operated Bellows vacuum cleaner. Previously #27 The “Baby Daisy” Vacuum Cleaner is constructed from timber, steel and leather bellows. It has a carry handle fixed to the top. The base is approx. 500mm x 250mm. The height is approx 400mm. On one side is a bracket for a handle (missing) used to operate the bellows. The device is mounted on a foot plate that is split. On one side of the bellows is a circular metal detachable hatch, fixed by wing-nuts. This has a central hole for a tube (missing). Attached internally to this hatch is a cloth dust collection bag. The metal hatch has the following moulded words arranged in a circular fashion. 'DAISY Vacuum Cleaner). There are two brass plates fixed to the side of the cleaner above the hatch. These plates are stamped with 'Rd. No. 518080 and Rd. No. 530353' Gold printed Labels on the side say the following. BABY DAISER Vacuum Cleaner. Registered England. No. 518080/7 No. 530353/08 Trade Mark No.294851 /07 Designs France No. 25469/08 Germany No. 330219 / 08 Further Patents applied for. In the centre of the label is a picture of a Daisy Flower. With the words Iles Patent. This is surrounded by a ribbon with the words. 'The Daisy Registered Trade Mark'. On one side near the base of the cleaner the number '7749' is stamped into the metal.fBaby Daisydomestic equipment, cleaning, vacuum cleaner

This item belonged to Dr Cyrus Jones, who performed a lot of circumcisions. There is a section on the tape made in the museum in c. June 1997 where Dr Jones talks about this. These devices were possibly made in Melbourne, perhaps by Surgical Manufacturers. The method of use for this item is as follows. Unscrew large screw to release bell. Bell sits on tip of penis inside prepuce. Pull prepuce up & through hole to trap prepuce skin. Reassemble, & tighten screw to prepuce and cut foreskin loose.A chrome metal medical device for performing circumcisions. Consists of a metal key/foot section, and a metal screw for tightening.surgery

This operating table belonged to the famous gynaecological surgeon Dr Victor Bonney and was given to Dr Frank Forster in 1953 by his widow Mrs Annie Bonnie, a distant relative of Forster's. Dr Victor Bonney (1872 - 1953) followed his father into medicine and trained at St Bartholomew's and the Middlesex Hospitals. Writing his obituary in 1953, FW Roques said of Bonney that he "'made three great gifts to surgery. First, he was the pioneer of myomectomy; second, with Berkeley, he extended and perfected Wertheim's operation for carcinoma of the cervix; and third, he devised a fine surgical technique emulated by so many of his pupils. To theatre sisters, labour-ward sisters and young house-surgeons he will always be remembered as the discoverer of 'Bonney's Blue' [antiseptic solution].'" Bonney's utilitarian, portable operating table has a round, worn scrubbed patch showing traces of his famous blue solution.This portable operating table was owned and used by pioneering gynaecological surgeon Sir Victor Bonney in London, U.K. c 1900. Dr Bonney employed two theatre sisters and had two sets of instruments and portable operating tables. This made it possible for Dr Bonney to 'complete three or more operations a day by rotating staff and equipment with a chauffeur driven Lanchester or Rolls Royce', delivering them from one house to the next. The donor of the operating table, the late Dr Frank Forster, was a distant relative of Sir Victor Bonney's widow, Annie Appleyard, formerly of Tasmania. When he visited her in the UK after Bonney's death, she offered the operating table to Dr Forster for the RANZCOG Museum. It was still in a canvas bag in the boot of one of Bonney's cars. Sir Victor Bonney was the pioneer of myomectomy, the surgical procedure for removing uterine fibroids. In collaboration with Berkeley, he extended and perfected Wertheim's operation for carcinoma of the cervix. Bonney was an influential teacher, developing and promoting conservatism of surgical technique (minimal intervention) that has had a lasting influence in modern surgical practice. To theatre-sisters, labour-ward sisters and young house-surgeons he will always be remembered as the discoverer of Bonney's Blue an antiseptic that was characteristically blue.Portable, laminated operating table. Plywood rectangular table with two laminated plywood extensions, a head board, and a foot board. At the foot board are insets of canvas straps to support a patient's ankles. Two detachable stirrup poles, each with a canvas strap attached, fit into two holes at the lower end of the table. The table is supported by two timber trellis cross braces with metal bars, and supported at the centre by a metal rod that allows the table to pivot up and down. Two metal arcs with a locking mechanism fix the table at the desired elevation, allowing a Trendelenburg tilt ( a 45 degree tilt, with the patient's head downwards.) The operating table is demountable for transportation and re-assembly.obstetric delivery

Clothing. Brown leather ladies shoes with 3cm heels. Pointed toes. Fold over flap across the bridge of the foot with cut out pattern. Fastened on outside of shoe with three flaps with button holes and three .8cm round plastic buttons. Heads of tacks visible on heels of shoes. Old box 573On sole of shoe, E.Salter Handsown, Gold lettering inside shoe, ''The Countess Handsown shoe by Ernest Salter. Late of Bond street and Piccadilly London. Exclusive for Mutual Store Ltd''.costume, female, brown leather ladies shoes

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

Cooper S.E. Ball Bearing Grinder made and guaranteed by Sunbeam Corporation Limited. Grinders like this example have been made the same since the early 1900s, with this grinder thought to have been produced in the 1960s. It is belt driven, with the other end of the belt being attached to an engine; the same engine that would have powered the overhead shearing equipment in shearing sheds. It was common for shearing teams to bring their own equipment, especially pre-1960 as most shearing sheds were not connected to power, and shearers preferred to work with their own equipment. The engines that powered the shears and grinder were typically fuelled with kerosene or petrol. The large circular disks are attached to the bolt that protrudes from the grinder and fastened tightly with a nut. An example of seeing a similar grinder in action can be found on the following link - https://www.youtube.com/watch?v=O7eimI_Gm9o. Inventor Frederick Wolseley made the world's first commercially successful power-shearing system in Australia in 1888. US company Cooper, which had been founded in 1843 as a maker of sheep dip, began selling Wolseley equipment in the USA in 1895. The Chicago Flexible Shaft Company successfully entered the power-shearing market a few years later and entered a joint venture with Cooper. It set up a branch in Sydney and sold shearing sets, and engines to power them, into the Australian market. In 1921 the US parent company, realising it needed to make products whose sales were not as seasonal as those of shearing equipment, made its first household appliances and branded them Sunbeam. In 1933, changes in exchange rates and taxes led the company to manufacture engines and shearing equipment in Australia via subsidiary Cooper Engineering, which changed its name to Sunbeam in 1946. Although most Australians know of this company as a major manufacturer of household appliances, its rural division flourished and retained the Sunbeam name for shearing equipment even after it was taken over by New Zealand company Tru-Test in 2001. The grinder is formed from a central arch shaped block of green painted metal. Much of this paint has been lost to age, leaving the grinder in a ‘farm used’ condition with much surface oxidation present. On the front of the arch is a specification plate, reading “Cooper S.E. ball bearing grinder. Made and guaranteed by Sunbeam”. At the foot of the arch, three bolt holes are found for securing the grinder to the base of a solid wooden surface. Two of the bolt holes are found on the front of the grinder, with another found on the rear. From the central arch, a bolt protrudes to the right of the grinder. This large bolt is for securing a grinding plate to the grinder. Above the central arch is a pendulum which holds the comb / cutter that is being sharpened. From the pendulum, a large arm extends down (not pictured) to meet and strike the plate spinning at a rapid speed. On the left-hand side of the central arch of the grinder, a wheel is found which a belt is attached to for power. This belt is then attached to a separate engine, spinning the wheel and hence powering the grinder. The wheel is partially covered with a section of protective bent tube, designed to provide protection from the rapidly spinning wheel. Below this wheel is the belt shifter. It is designed to move the protective bent tube from one side of the grinder to the other, to accommodate the grinder in the setup of different shearing sheds. The two separate grinding plates are identical. They have a slight slope for sharpening the comb and cutters in the correct method, with a slight bias towards the base, or “tooth”, of the equipment. The disks have a large central bolt for attaching to the grinder. They have tags on the horizontal axis of the grinding plates, for securing the plates in transportation, and to help with initial alignment when setting up the grinder. The reverse of these grinding plates has the same green painted metal finish found on the grinder. This paint is also in a ‘farm used’ condition, with surface oxidation present. The grinder would be provided from the factory with a comb holder, shifter for securing the grinding plates, emery cloth and emery glue. The emery cloth is what does the actual grinding and is applied to the grinding disks, replacing once well worn. These items can be seen in the final images in the multimedia section, showcasing advertising for this grinder. Plate. Inscribed. “Cooper / S.E. BALL BEARING GRINDER / MADE AND GUARANTEED BY / Sunbeam / CORPORATION LIMITED / SYDNEY MELBOURNE / ADELAIDE BRISBANE ”sheep shearing, shearing equipment, sunbeam, grinder

Used by donor's father approx. 80 years ago i.e.c1972Wooden foot form - used for stretching boots or shoes. Punched with holes to accept pressure point plugs. The form is hinged at the instep to enable forms to be pushed into the shoe.The Horbrocostume accessories, footwear accessories

Used at Common School, Rutherglen around 1920s, particularly at examination time. See also 62.1Wooden desk, green top, book shelf under top, on four legs, front ones vertical, back ones sloped. Hole for ink well RH side, pencil slot, foot rest (central), black legs, extra narrow ledge at backschool, common school, education

Initial thinking about the establishment of Holmbush 'for boys whose earnings and family circumstances are insufficient to enable them to pay full rates for Board & Lodging; and to extend to them the supervision benefits, and comradeship of Legacy."Further documentation on the practicalities of establishing a Legacy residence for boys. The then current costs are detailed.3 carbon copied foolscap sheets, tattered at the foot, and typed onto paper previously used for a schedule of works for Spicer Detmold. Two punched holes for filing.00297.1 Item 2.a "Day, Fullarton (2) Priest, (illegible)" 00297.2. Item 2.e "+ Churches, Sports Grounds, Swimming Pool & (illegible)" holmbush initial negotiations, holmbush

A pair of horse-riding stirrup foot holders, made of steel. Shape is arched, with flat base for holding foot. Long, rounded hold attached to top for stirrup. Base is oval hole.No visible markingsrural industry, agriculture, stirrup, horse, riding, jessie

Wandin Thomas Sebire JP (1867-1960) learnt boot-making as a young man. In a small workshop on his property in Sebire Avenue, Wandin he made boots for family, friends & neighbours. He also repaired boots & made other small leather articles. Bootmaking is a complex process requiring a variety of tools. The leather is cut to shape, glazed & burnished (polished) with heated irons. The pieces are stretched onto, & nailed to, a wooden last to form the boot. Once attached to the insole, the boot is finished on a metal last. Uppers are stitched with waxed thread through holes made with an awl. Heels comprise pieces nailed together & neatened with a heel shave. Metal plates, short nails or hob nails driven into the sole & heel, often in a pattern, improved durability.Cast Iron Last on a four-footed base/stand. Last is removable from stand, and can be moved into different positions on top of the stand.bootmaking tools, boot lasts

Wandin Thomas Sebire JP (1867-1960) learnt boot-making as a young man. In a small workshop on his property in Sebire Avenue, Wandin he made boots for family, friends & neighbours. He also repaired boots & made other small leather articles. Bootmaking is a complex process requiring a variety of tools. The leather is cut to shape, glazed & burnished (polished) with heated irons. The pieces are stretched onto, & nailed to, a wooden last to form the boot. Once attached to the insole, the boot is finished on a metal last. Uppers are stitched with waxed thread through holes made with an awl. Heels comprise pieces nailed together & neatened with a heel shave. Metal plates, short nails or hob nails driven into the sole & heel, often in a pattern, improved durability.Wooden, folding, foot measure/ruler with brass clasps.bootmaking tools, measures, rulers

left foot solid wood last with leather bunion extension on outer side. Good condition. Hole in heel possibly to allow for hanging Last in 2 parts secured by screw Well worn with tack holes on sole 2 nails on upper timber discolouration'12', '5562' stamped into upper.

dark timber staining on upper. 2 nails on upper. hole through heel. screw attaching arch to sole section. hole part way through inside arch12,4 stamped on upper section. 5562 stamped on sole section.

Cast iron left shoe last with rectangular hole at heel end for removable leg(.7 stamped at toe. Cast holes on sole. Cast holed on outer aspect of foot Raymond stamped on outer aspect at heel end

098?? stamped on instep. Removable instep cast ? 241 on foot cast with locating grooves for instep cast. Locating hole on under foot arch

Cast iron shoe last with instep slide and instep grove in foot space6 DD on toe, 2 cast holes on sole, 1 cast hole on upper toe, 2 cast holes on right bunion side

An unattributed draft report dated 19/04/1972 (to be read in conjunction with Cat. No. 01670) which updates Cat.No. 01672. The report gives details of the situation at that date and projected changes to the functions of the residences, occupancy rates, costs and likely trends in accommodation needs. It explores at length auxiliary and alternate accommodation such as the Salvation Army, YMCA, YWCA and church hostels, before recommending that when the number of residents over the age of 14 falls below 34 in two consecutive years Blamey House be disposed of or developed for other needs, Stanhope is converted to co-ed accommodation for over 14s, and Harelands is used as co-ed accommodation for the under 14s. The report also recommends investigating as a separate project maintaining a separate cottage for problem children.Part of the history of Melbourne Legacy's involvement with residential care for children.White foolscap sheets x 8 pages, with black type. Two holes punched for filing, and add-in. Page 1: in pencil: 'DRAFT 19/4/72 Discussed with J. Chancellor and G. Rosman 19-4-72 Page 3: pencilled 'A' circled and inserted before Item 5. Page 7: In pencil: 'See conclusions attached' at foot of page. 01673(8): in pencil circled 'A', in blue biro 'end of Para 4' 01673(9): in pencil: (i) 'de' scribbled out (iii) 'or re-development of site for other Legacy needs' after 'Disposal of Blamey House, 'Extend' changed to 'Limit', 'limit' deleted, 'for' changed to 'to', 'Havelands' changed to 'Harelands', 'Haveland plus' deleted, '(See addendum ---)' at end.residences, review, blamey house, harelands, stanhope

Viola Annie McVicars (1911–1990) was born in Korumburra on 29 April 1911. At the age of 21, she married William John Ayling (1909–1995). After their marriage in 1932, they moved to Kew, initially to 81 Tennyson Street, and later to 180 Pakington Street. A professional tailoress, Viola Ayling was also a talented amateur potter, creating her ceramics at her home in Pakington Street, where she had an internal studio and a handmade, wood-fired brick kiln in her backyard. Following her death in 1990, her studio pottery passed to her daughter, and following the daughter’s death, to her granddaughter. This piece of glazed earthenware is part of a collection of 15 functional and decorative ceramic items donated by Viola’s granddaughter to the collection in 2024.A handmade lamp base, expertly potted and glazed. The style is representative of Australian ceramic design of the period, particularly that employed by Klytie Pate.Handmade lamp base, irregularly ridged with applied green and yellow glazes. The lamp base has a hole for a cord above the foot.Signature to base: "V. Ayling"ceramics, pakington street -- kew (vic.), lamp bases, viola annie ayling, viola annie mcvicars

Rail used by The North Melbourne and Essendon Tramways and Lighting Co. at their Essendon Depot. Based on item 2566, originally rolled by Carnegie Steel in Pittsburg. The reference link provides the history of the company. Section taken from No. 13 road July 2005. Has rolling date welded onto one side, with location and date written in yellow paint on the foot of the rail.Yields information about the type of rail used in 1906 at Essendon Tram depot.Section of rail recovered from Essendon Tram depot relay with "1906" welded to one side. Has a hole on the underside cut using an oxy-acetylene torch for a bolt possibly to secure the rail. Has been sawn from a salvaged section of rail. See item 2566 for a photograph of a section of rail at Essendon depot with the date and manufacturer's name rolled onto it. tramways, rail, essendon tram depot, carnegie steel, nmetl

Set of 14 tram car templates contained within Reg Item 356, cut from card board to indicate the over all dimensions of the various type of tramcars. Would have been used in the drawing office for checking clearances on buildings, trackwork, junctions. Cut with holes in the centre to enable this to be done. Scale 1/2" = 1 foot. .1 - Marked "A" - for a combination car - 30' 11.25" long, 7'6" wheelbase .2 - "B" - for a combination car - 32' long, 6'6" wheel base to drawing R489 and summer or straight sill car to drawing R820. .3 - "C" - Straight Sill combination car - 33' long, 7'6" wheelbase. .4 - "D" - Combination car, length 31'11", 7'6" wheelbase .5 - "E" - Combination car, length 35', 7' wheelbase .6 - "F" - DC Bogie car, to Drawing 112, length - 44' 3.5", truck centres 22 '4" .7 - "G" - ditto length 44' 5.5", truck centres 23' 7.5" .8 - "H" - ditto length 44' 5.5", truck centres 24' 7.5" .9 - "J" - four motor bogie, to drawing 854, length 45' 6", truck centres 24'6" .10 - "K" - Combination car, length 35', 12' Radiax truck. .11 - Bogie tramcar, W class length 48', truck centres 26' 6" .12 - ditto, W2 534, length 48', truck centres 26' 0" .13 - W4 class tram, .14 - W5 730, length 46' 6', truck centres 28'trams, tramways, mmtb, plans, drawings, templates

This Journal "The bad bit across the River" was written by - LtCol HPG Clews in 1934 and is about his experiences around the Colo River approximately 60 miles NW of Sydney, NSW. LtCol Clews was a remarkable man and his achievements were just as remarkable. He is affectionately known as "The Major." He served in the British Army 1909 - 1911 with the Sherwood Foresters. He then served in the Royal Australian Survey Corps from 1912 - 1949 and then served as the Senior Surveyor with the Snowy Mountains Authority from 1950-1958. A Survey Cairn is errected in Khancoban to record his life 1890 - 1980. This Journal records the field trip to establish Survey Control in very rugged country by a handful of party members on foot. The map shows the routes taken.14 x foolscap pages stapled and two hole punched. The Journal includes a map, 7 x pages of typed text and 4 x Annexesroyal australian survey corps, rasvy, fortuna, army survey regiment, army svy regt, asr, 2nd field survey company

Shoe stretchers like this have been used for centuries, particularly for leather shoes that required breaking in. The wooden design and metal screw mechanism suggest it is an early to mid-20th-century model.This is a vintage wooden shoe stretcher with a metal screw mechanism. The item consists of: A wooden foot-shaped piece that is split into two halves, allowing for expansion. Several small holes in the wood, possibly for ventilation or for attaching additional stretching pegs. A metal rod with a threaded screw mechanism, which can be adjusted by turning a T-shaped handle at the top to widen the wooden sections and stretch a shoe. The overall design suggests it was used for maintaining the shape of shoes or expanding tight-fitting leather footwear.shoe stretcher, shoes, boots, household item, commercial equipment, bookmaker

This tool is likely part of an older hand-cranked or foot-operated drill system, possibly used for working on wooden spokes in wheelwrighting or for drilling in metal or leatherworking. Such tools were commonly found in workshops from the late 19th to early 20th centuries before electric drills became widespread. Steel Drill Spoke used for making holes in wheel hubs for inserting spokes.The item appears to be an antique drill spoke or a hand-operated tool component, possibly from a blacksmiths or wheelwright’s workshop. It consists of a cylindrical, rusted metal body with a tapered, pointed end, which may have been used for drilling or reaming holes. The base is attached to a mounting bracket with bolt holes, likely for securing it to a workbench or machinery.drill, spoke, wheel, hub, commercial equipment, wagon, gig, buggy

Used for trimming and shaping horse hooves to maintain proper foot health. The curved cutting blade allows for precise removal of overgrown or damaged hoof material. Essential for farriers and horse owners to ensure hoof balance, comfort, and prevention of lameness. Also used in preparing hooves for horseshoes.A rusted handmade metal tool with a curved cutting blade on one end. The handle is long and slightly tapered, with a hole near the end, possibly for hanging or securing a grip. The blade has a sharp, angled edge, designed for cutting through tough hoof material.hoof, cutting tool, horse, farm equipment, horse equipment