Showing 123 items
matching wood saw
-
The Beechworth Burke Museum
Photograph, 1859
... this photograph was taken. Louis Chevalier’s mill stopped sawing wood... sawing wood and began milling flour at some point between 1860 ...Louis Chevalier, brother of popular artist Nicholas Chevalier, opened a sawmill in Beechworth near Spring Creek in Newtown in 1853. This facilitated a boom in building in the town, as materials were much more available than they had been previously. A second sawmill was opened in the town in 1856. Louis Chevalier served on the Beechworth Council as a representative of Newtown between 1858 and 1860. As this photograph is taken in 1859, the mill would have been operating as a sawmill at the time this photograph was taken. Louis Chevalier’s mill stopped sawing wood and began milling flour at some point between 1860 and 1862. At this time, the Oven’s district was almost self-sufficient, producing considerable quantities of grain, dairy, fodder and meat. Unfortunately, the region experienced poor agricultural yields in the 1880s and 1890s, which lead to the closure of the Beechworth Flour Mills in the 1880s. This photograph depicts the first sawmill in Beechworth, which was responsible for making the materials available for other early buildings in the town. The mill race and wheel are also clearly depicted, which may shed light onto how mill wheels of this era and place were constructedBlack and white rectangular photograph printed on matte photographic paper mounted on boardReverse: 3146 / 1997.2654 / Louis Chevalier's Flour Mill on / the Newtown Falls before the / Bridge / Est 1853 / this photo 1859 / 84-229-1 / Burke Museum Beechworth / Page 41 / 81 % / (Illegible) / (Illegible) 14 / chevalier, louis chevalier, newtown, mill, grain mill, sawmill, flour mill, 1850s beechworth, beechworth council, farming and agriculture, victorian agricultural history, spring creek, buildings, industry, forestry, wood, timber -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Photograph, Black & White J. L. Smith Hay & Grain Store Bentleigh c1910, c1910
... ' & Shed from Mr Box and commenced business as a wood merchant... from Mr Box and commenced business as a wood merchant - sawing ...John Logan Smith 1860-1932 , the son of Irish immigrants James and Marianne Smith was born at their home near the 'Toll Gates' on Point Nepean Road and Dendy Street. East Brighton. At that time the area had many orchards that were later replaced by market gardens. J.L.Smith at first rented a cottage 'Law Muir Den' & Shed from Mr Box and commenced business as a wood merchant - sawing logs into shorter pieces using one horse to power the saw. He purchased the property, added to the buildings , began trading in fuel and fodder as well and installed a chaff cutting mill powered by 10hp steam engine. The business prospered 1909 following the death of Tommy Bent, J/L Smith was nominated for Councillor of the Shire of Moorabbin. WW1 1914 - 18 both John and Mary Ann supported local War Relief Auxiliaries and their son Vic served as a Signaler in AIF. As Motor transport was increasing 1926 J L Smith built a small Garage on the opposite corner (Woolworths Supermarket 2005) , employed a good mechanic ( Reg Hunt ) and developed another successful business. The Grain Store was managed by family until 1930. In 1932 JL Smith assisted a man whose car had broken down, pushing it to the garage and sadly suffered a heart attack and died. He is buried in Cheltenham Cemetery. J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.Black & white photograph of the Hay & Grain Store of John Logan Smith 1860-1932 on the corner of Jasper Rd and Centre Rd Bentleigh ( East Brighton) c1910. A Horse drawn cart loaded with hay and another outside the first building used by J L Smith -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Photograph, Black & White, J.L.Smith Hay & Grain Store c1916 Bentleigh, 1916
... ' & Shed from Mr Box and commenced business as a wood merchant... from Mr Box and commenced business as a wood merchant - sawing ...John Logan Smith 1860-1932 , the son of Irish immigrants James and Marianne Smith was born at their home near the 'Toll Gates' on Point Nepean Road and Dendy Street. East Brighton. At that time the area had many orchards that were later replaced by market gardens. J.L.Smith at first rented a cottage 'Law Muir Den' & Shed from Mr Box and commenced business as a wood merchant - sawing logs into shorter pieces using one horse to power the saw. He purchased the property, added to the buildings , began trading in fuel and fodder as well and installed a chaff cutting mill powered by 10hp steam engine. The business prospered 1909 following the death of Tommy Bent, J/L Smith was nominated for Councillor of the Shire of Moorabbin. WW1 1914 - 18 both John and Mary Ann supported local War Relief Auxiliaries and their son Vic served as a Signaler in AIF. As Motor transport was increasing 1926 J L Smith built a small Garage on the opposite corner (Woolworths Supermarket 2005) , employed a good mechanic ( Reg Hunt ) and developed another successful business. The Grain Store was managed by family until 1930. In 1932 JL Smith assisted a man whose car had broken down, pushing it to the garage and sadly suffered a heart attack and died. He is buried in Cheltenham Cemetery J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.Black & White photograph of J L Smith Hay & Grain Store and Crushing Mill Jasper Rd / Centre Rd Bentleigh 1916. A veranda has been added to the store, new signage attached and a Gas light and hitching post are in foreground. 3 Horse drawn carts loaded with grain bags and drivers sitting on top of loadV. Smithgas street light, hitching posts, smith vic, photography, smith j l; smith mary ann, stanley helen, smith vic, smith harry redvers, chaff cutter, horse drawn carts, toll gates brighton, motor cars 1900, steam engines, early settlers, bentleigh, parish of moorabbin, city of moorabbin, county of bourke, moorabbin roads board, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman s, highett william, ormond francis, maynard dennis, market gardeners, vineyards, orchards -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Photographs, x 2 ,Black & White, F Smith Horse drawn cart loaded, Baled Straw, Grain, c1920
... ' & Shed from Mr Box and commenced business as a wood merchant... from Mr Box and commenced business as a wood merchant - sawing ...John Logan Smith 1860-1932 , the son of Irish immigrants James and Marianne Smith was born at their home near the 'Toll Gates' on Point Nepean Road and Dendy Street. East Brighton. At that time the area had many orchards that were later replaced by market gardens. J.L.Smith at first rented a cottage 'Law Muir Den' & Shed from Mr Box and commenced business as a wood merchant - sawing logs into shorter pieces using one horse to power the saw. He purchased the property, added to the buildings , began trading in fuel and fodder as well and installed a chaff cutting mill powered by 10hp steam engine. The business prospered 1909 following the death of Tommy Bent, J/L Smith was nominated for Councillor of the Shire of Moorabbin. WW1 1914 - 18 both John and Mary Ann supported local War Relief Auxiliaries and their son Vic served as a Signaler in AIF. As Motor transport was increasing 1926 J L Smith built a small Garage on the opposite corner (Woolworths Supermarket 2005) , employed a good mechanic ( Reg Hunt ) and developed another successful business. The Grain Store was managed by family until 1930. In 1932 J L Smith assisted a man whose car had broken down, pushing it to the garage and sadly suffered a heart attack and died. He is buried in Cheltenham Cemetery. J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.2 x Black & White photographs showing horse drawn carts loaded with (a) Hay and (b) bags of grain outside J.L.Smith Grain & Chaff Store Centre Rd Bentleigh c1920smith frank, smith arch, smith tom, smith j l; smith mary ann, stanley helen, smith vic, smith harry redvers, chaff cutter, horse drawn carts, toll gates brighton, motor cars 1900, steam engines, early settlers, bentleigh, parish of moorabbin, city of moorabbin, county of bourke, moorabbin roads board, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman s, highett william, ormond francis, maynard dennis, market gardeners, vineyards, orchards -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Photograph - Washing Day at 'Law Muir Den' Mrs J L Smith c1910, c1910
... from Mr Box and commenced business as a wood merchant - sawing... from Mr Box and commenced business as a wood merchant - sawing ...Mrs J.L.Smith and Ada Smith in the backyard of the house Law Muir Den 510 Centre Rd Bentleigh c 1910. . The early settler women usually devoted a whole day to washing as it was very labourious. A fire was lit in a stone pit and a large tub of water boiled. Soap that had been made, usually in the previous Autumn, from fat drippings and caustic soda, was flaked into the tub to form suds. The clothes were moved around in the tub with a long wooden paddle that was also used to lift the clothes out of the tub into another tub of cold rinsing water..Stains were removed by scrubbing soap on the cloth against a scrubbing board. Clothes were wrung by hand or a mechanical wringer and hung on the clothes line to dry. Mary Ann Smith was married John Logan Smith 1860-1932 who at first rented a cottage 'Law Muir Den' & Shed from Mr Box and commenced business as a wood merchant - sawing logs into shorter pieces using one horse to power the saw. He purchased the property, added to the buildings , began trading in fuel and fodder as well and installed a chaff cutting mill powered by 10hp steam engine. The business prospered As Motor transport was increasing 1926 J L Smith built a small Garage on the opposite corner (Woolworths Supermarket 2005) , employed a good mechanic ( Reg Hunt ) and developed another successful business. J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.Photograph, Black & White, showing 2 women washing clothes in a large tub, set over a fire in a stone pit, in the back yard. Clothes are hanging from a rope line strung between 2 trees and held up with a wooden 'prop' -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Photograph - Photograph, Black & White Mrs J.L.Smith & Butcher, 1915
... from Mr Box and commenced business as a wood merchant - sawing...' & Shed from Mr Box and commenced business as a wood merchant ...The Butcher Mr Bill Ellin delivering meat to Mrs J.L.Smith in front of the house Law Muir Den 510 Centre Rd Bentleigh c 1915. Groceries, Ice, Milk, Bread, Eggs, Poultry were delivered to housewives by the traders in horse drawn carts, Also Hawkers and Pedlars plied their wares by visiting the cottages. John Logan Smith 1860-1932 , the son of Irish immigrants James and Marianne Smith was born at their home near the 'Toll Gates' on Point Nepean Road and Dendy Street. East Brighton. At that time the area had many orchards that were later replaced by market gardens. J.L.Smith at first rented a cottage 'Law Muir Den' & Shed from Mr Box and commenced business as a wood merchant - sawing logs into shorter pieces using one horse to power the saw. He purchased the property, added to the buildings , began trading in fuel and fodder as well and installed a chaff cutting mill powered by 10hp steam engine. The business prospered 1909 following the death of Tommy Bent, J/L Smith was nominated for Councillor of the Shire of Moorabbin. WW1 1914 - 18 both John and Mary Ann supported local War Relief Auxiliaries and their son Vic served as a Signaler in AIF. As Motor transport was increasing 1926 J L Smith built a small Garage on the opposite corner (Woolworths Supermarket 2005) , employed a good mechanic ( Reg Hunt ) and developed another successful business. The Grain Store was managed by family until 1930. In 1932 JL Smith assisted a man whose car had broken down, pushing it to the garage and sadly suffered a heart attack and died. He is buried in Cheltenham Cemetery. J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.A Black and white photograph c 1915 showing the Butcher delivering meat to Mrs J.L Smith Bentleighsmith j l, smith mary ann, stanley helen, smith vic, smith harry redvers, chaff cutter, horse drawn carts, toll gates brighton, motor cars 1900, steam engines, early settlers, bentleigh, parish of moorabbin, city of moorabbin, county of bourke, moorabbin roads board, shire of moorabbin, henry dendy's special survey 1841, bent thomas, charman s, highett william, ormond francis, market gardeners, vineyards, orchards, william ellin, butcher -
Flagstaff Hill Maritime Museum and Village
Tool - Chisel, 1940-1962
... resurrected as Irwin/Marples and applied to wood chisels and table saw... to wood chisels and table saw blades now made at their new ...William Marples junior joined his father's joinery making business in 1821. In 1860 William's sons joined him and the firm became William Marples and sons. Over the years they acquired John Moseley & Sons a London plane maker and Thomas Ibbotson & Co a Sheffield edge tool maker. Growing to become the most prolific and best known Sheffield tool maker. Their large factory was known as the Hibernia Works. Their trademark was a shamrock that appeared on some of their tools, in 1961 they had about 400 employees. In 1962 the record Tool Company and William Ridgway acquired a fifty percent interest in the company and in 1972 the companies merged with several others to form Ridgway Tools Ltd. After 116 years at its Hibernia Works, the company was moved to Dronfield. A 1982 takeover by A G Bahco of Sweden was short-lived and in 1985 Record Ridgway returned to British ownership first as Record Marples Woodworking Tools Ltd. In 1988 then as Record Holdings PLC in 1993. In 1998 the company accepted a bid from American Tool Corporation, subsequently trading as Record Irwin. The Irwin company itself was acquired by Newell Rubbermaid in 2002 and renamed Irwin Industrial Tool Co. Both the Marples and Record names were re-branded "Irwin" However the name has since been resurrected as Irwin/Marples and applied to wood chisels and table saw blades now made at their new facility in Udine, Italy. As a footnote, William Marples was the uncle of Robert Marples and Joseph Marples, both of whom established competing tool making businesses in Sheffield. The Robert Marples firm disappeared early in the 20th century. After several changes in the company's ownership tools are now made under the Ridgway name but in China.A tool made by a company with a long family history of tool making in Sheffield England, with a member of the Marples family, Joseph Marples establishing a competing tool company which continues today to manufacture quality products for the joinery and shipwrights trades.Socket chisel with 1/2" blade."Marples & Son" stamped on bladeflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, hand tool, ward chisel, woodwork chisel, marples and sons, cabinet makers tools, william marples and sons -
Flagstaff Hill Maritime Museum and Village
Tool - Caulking Tool, William Marple & Sons, Early 20th century
... to wood chisels and table saw blades now made at their new... to wood chisels and table saw blades now made at their new ...Caulking is the traditional technique used on wooden vessels built with butted or clinker-built planks to fill the gaps between these planks while still allowing the wood to flex and move. This involved driving the irons, hammered in with the mallet, deep into the seams to open them up. After this, spun yarn, oakum (hemp) or cotton was driven deep into the gaps. The hemp or cotton was soaked in creosote or pine tar to make the joins watertight. Caulking also played a structural role in tightening up the hull or deck by reducing the longitudinal movement of the neighbouring planks. William Marples junior joined his father's joinery making business in 1821. In 1860 William's sons joined him and the firm became William Marples and sons. Over the years they acquired John Moseley & Sons a London plane maker and Thomas Ibbotson & Co a Sheffield edge tool maker. Growing to become the most prolific and best known Sheffield tool maker. Their large factory was known as the Hibernia Works. Their trademark was a shamrock that appeared on some of their tools, in 1961 they had about 400 employees. In 1962 the record Tool Company and William Ridgway acquired a fifty percent interest in the company and in 1972 the companies merged with several others to form Ridgway Tools Ltd. After 116 years at its Hibernia Works, the company was moved to Dronfield. A 1982 takeover by A G Bahco of Sweden was short-lived and in 1985 Record Ridgway returned to British ownership first as Record Marples Woodworking Tools Ltd. In 1988 then as Record Holdings PLC in 1993. In 1998 the company accepted a bid from American Tool Corporation, subsequently trading as Record Irwin. The Irwin company itself was acquired by Newell Rubbermaid in 2002 and renamed Irwin Industrial Tool Co. Both the Marples and Record names were re-branded "Irwin" However the name has since been resurrected as Irwin/Marples and applied to wood chisels and table saw blades now made at their new facility in Udine, Italy. As a footnote, William Marples was the uncle of Robert Marples and Joseph Marples, both of whom established competing tool making businesses in Sheffield. The Robert Marples firm disappeared early in the 20th century. After several changes in the company's ownership tools are now made under the Ridgway name but in China. A tool made by a company with a long family history of tool making in Sheffield England, with a member of the Marples family, Joseph Marples establishing a competing tool company which continues today to manufacture quality products for the joinery and shipwrights trades.Caulking tool straight wide blade, Stamped "W Marples & Sons" & James S Steele tool box.flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, caulking tool, caulking iron, james s steele -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, large Saw, 2 man, c1900
... alternate pulling the saw through the wood. If the kerf -slit- began...A long steel blade saw with 2 wood handles c1900..., large Saw, 2 man A long steel blade saw with 2 wood handles ...Early settlers had to clear the land of trees and shrubs to establish and maintain their farms and market gardens. Some settlers worked in the Gippsland region felling timber for transport by bullock wagons to Melbourne. Two-man crosscut saws were primarily important when human power was used. Such a saw would typically be 1 to 4 m (4 to 12 feet) long, and sometimes up to 5 m (16 feet), with a handle at each end. The technique in using a two-man saw involved a sawyer standing at each end and together the sawyers would alternate pulling the saw through the wood. If the kerf -slit- began closing, causing the saw to bind, wedges would be inserted behind the saw blade in order to keep the kerf open.Two-man saws were designed to cut in both directions. Careful tooth design was necessary to clear the sawdust during the cut. This is a typical two-man tree felling saw that was necessary to clear the land when the pioneers were establishing their market gardens and farms in Parish of Moorabbin c1850A long steel blade saw with 2 wood handles c1900tools, saws, axes, early settlers, pioneers, market gardeners, dairy farms, orchards, vineyards, timber mills, bullock wagons, tree felling, timber mills, city of moorabbin, county of bourke, moorabbin roads board, parish of moorabbin, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman stephen, highett william, ormond francis, maynard dennis, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tool - Tools, Saw double sided pruning 20thC, 20thC
Among the early settlers in Moorabbin Shire were blacksmiths who made tools for the other settlers who were establishing the homes, market gardens, farms, orchards and various businesses. Early settlers were self reliant and repaired their own equipment for kitchen,dairy, farm, horses, carts using various tools . This is a double sided pruning saw with tapering blade used by orchardists and farmers This pruning saw is typical of the type used by early settlers in Moorabbin Shire c1900A steel saw with double sided tapering blade and wood handle for pruning trees. saws, pruning saws, orchardists, fower gardens, fruit trees, early settlers, market gardeners, blacksmiths, tools, building equipment, hammers, moorabbin shire, bentleigh, mckinnon, highett, cheltenham,mcewan james pty ltd, melbourne, bunnings pty ltd, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, steel hacksaw 'Marples', 20thC
A hacksaw is a fine-toothed saw, originally and principally for cutting metal. They can also cut various other materials, such as plastic and wood; for example, plumbers and electricians often cut plastic pipe and plastic conduit with them. On hacksaws, as with most frame saws, the blade can be mounted with the teeth facing toward or away from the handle, resulting in cutting action on either the push or pull stroke. In normal use, cutting vertically downwards with work held in a bench vice, hacksaw blades should be set to be facing forwards. Joseph Marples & Son Pty Ltd Traditional Craftsmans Hand Tools made in Sheffield. The finest quality hand made tools, backed by over 170 years of manufacturing heritage. .In the 1840’s Joseph Marples was one of several ‘Marples’ (most of which were related) in Sheffield manufacturing joiners tools, such as brass inlaid rosewood & ebony braces, boxwood spokeshaves, beech planes, gauges and squares. The business has remained within the family to this date, and has been based in Sheffield since those early days. Although modern technology has been used in some instances, many of the traditions of manufacturing fine hand tools has remained the same using selected materials and hand finishing, indeed the same threads are used in the gauges as were used over 100 years ago. A steel hacksaw. 'Marples' with bladeMARPLEStools, woodwork, metalwork, carpentry, pioneers, market gardeners, early settlers, moorabbin, cheltenham, bentleigh, ormond, joseph marples & son pty ltd, sheffield , england, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, steel hacksaw with wooden handle, c1900
A hacksaw is a fine-toothed saw, originally and principally for cutting metal. They can also cut various other materials, such as plastic and wood; for example, plumbers and electricians often cut plastic pipe and plastic conduit with them. On hacksaws, as with most frame saws, the blade can be mounted with the teeth facing toward or away from the handle, resulting in cutting action on either the push or pull stroke. In normal use, cutting vertically downwards with work held in a bench vice, hacksaw blades should be set to be facing forwards. A steel hacksaw with a wooden handle but without blade -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, Coping saw, c1900
A coping saw is a type of hand saw used to cut intricate external shapes and interior cutouts in woodworking or carpentry. It is widely used to cut mouldings to create coped rather than miter joints. It is occasionally used to create fretwork though it is not able to match a fretsaw in intricacy of cut, particularly in thin materials. Coping saw blades are always thicker and much coarser cutting than typical fretsaw blades. A coping saw consists of a thin, hardened steel blade, stretched between the ends of a square, c-shaped, springy-iron frame to which a handle is attached. The blade is easily removed from the frame so that the blade can be passed through a drilled hole in the middle of a piece of wood. The frame is then re-attached to the blade and the cut starts from the middle of the piece. Long cuts perpendicular to the edge of the material are possible but the shallow depth of the frame rather limits how far from the edge one may cut. The much deeper frame of the fretsaw is more useful for cutting well away from the edge but conversely cannot manage the thicker materials commonly cut by the coping saws. The coping saw blade is installed with the teeth pointing towards the handle. Unlike a hacksaw, which has the teeth pointed away from the handle, the coping saw cuts on the pull stroke. The coping saw blade is removable by partially unscrewing the handle. The blade is prevented from rotating by means of the short, steady bar provided where the blade is attached. Loosening the handle also allows the blade to be rotated relative to the frame as desired. Carefully aligning the finger steady bars at the top and bottom of the blade ensures that the thin blade is straight and not twisted along its length. Re-tightening the handle tensions the blade and locks it at the desired angle relative to the frame. The short steady bar nearest the handle is held securely between finger and thumb while the handle is tightened to ensure the blade remains at the desired angle. Unlike the fretsaw the coping saw blade has holding pins which lock securely into the angled slots of the rotatable blade holders. Gentle curves are achieved by slowly turning the whole frame by means of the handle while continuing to cut steadily. A coping saw with wooden handle but no bladetools, saws, steel , clamps, metalwork, woodwork, carpentry, early settlers, pioneers, market gardeners, moorabbin, bentleigh, cheltenham, fretsaw, coping saw, bowsaw, blacksmiths, -
Federation University Historical Collection
Newspaper, The Machinery Market, 02/12/1889
It's assumed that this journal was read at the Ballarat School of MinesA small illustrated journal with advertisements and pictures. pages 328-356 (and 26 pages of illustrated advertisements). Illustrations include machinery, corn crushers, condensers, chlorination plants. stea, hammers, steam engines, steam pumps, lamps, saw bench, leather belting, casks, barrels, machinery, boiler, cohran and co, birkenhead, stern, cowles syndicate company, electric smelting works, aluminium manufacturing, w t glover and co, rope machine, steam travelling crane, webster wood fibre machine, automatic govenor expansion gear, international exhibition edinburgh, beacon light, air propeller, well boring tools and pumps, cochran and co.'s launch, tug and boat building yard, s.s. jeanette, cochran boiler, cochran and co's boiler shop, stern wheel steamer, s.s. esperanca, cowles syndicate co, milton, w.t. glover & co.'s patent compound rope making machine, bendh drilling machine, steam launch, bicycle, well-boring tools -
Flagstaff Hill Maritime Museum and Village
Domestic object - Wooden Bread Board, Not known
In the high tech, fast paced society that we live in, it’s easy to take some things for granted. Case in point: the wood cutting board on which you’ll probably be preparing the evening’s dinner. Have you ever taken the time to think about the history of the cutting board? Where did it come from, and what did ancient civilizations use to cut their meats, fruits and vegetables? Wood throughout the ages Since the dawn of time, wood has been one of the most available materials used by mankind to build tools and lodgings, so it’s not really surprising to know that wood has been used in the preparation of food since the prehistoric ages. Of course, back then, cavemen probably used an unpolished slab of tree trunk to cut the kill of the day on and they probably didn’t think twice about saving it once the meal was over. Chances are they probably threw it in the fire with the rest of the wood needed to kindle it. Advances in technology Throughout the centuries, mankind evolved and started creating machines from steam, electricity and metal. When the circular saw was invented, nicer, cleaner slabs of wood were cut and used as cutting boards. Since soft wood was the most available type of wood at the time, it was the material of choice for to be used for cutting boards. Boards were made smaller since the slab of wood could now be cut to any desired size. Since they were made smaller, they were also used to eat off of and some people referred to them as trenchers. Trenchers were originally pieces of stale hard bread that were used as substitute plates. Wood trenchers quickly became the replacements of the eatable dinnerware. The butcher block: the cutting board’s larger cousin In the industrial ages, many industries rapidly developed, and the butchery industry followed this trend as well. Before the invention of the cutting board, butchers used tree rounds to carve their meat on. The rounds were often too soft and they rapidly became unsanitary. Hard maple wood butcher blocks were the preferred choice of the industry. They were made to be extremely thick and durable, so durable in fact, that a butcher could use the same block for almost his entire career. Cutting boards around the world As cutting boards began to be more and more used in kitchens around North America, the rest of the world crafted such boards from different materials. The East used thick bamboo as their material of choice. Despite its frail appearance, bamboo is quite strong and made durable cutting boards and butcher blocks. Europe used maple in the crafting of their cutting boards while Persia used flat pieces of polished wood in their kitchens. The world then saw cutting boards that were being made from other materials like plastic and they came in all shapes and sizes, but they always served the same purpose, to provide a household with a safe, clean surface on which to prepare meals for their friends and family members. https://www.woodcuttingboards.com/news/quick-history-of-the-cutting-board-47.aspxThe use of the wooden chopping board over time. Wooden Rectangular Bread board . Worn (concave in centre). Raw wood.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, chopping board, cooking -
Flagstaff Hill Maritime Museum and Village
print - Picture of Sailing Ship, Rowland Hilder 1905 -1993, 20th Century
The use of sails to propel a ship along its course dates back at least to 3000 BC., to the Egyptians who used sails to move their vessels up and down the Nile. Sailing ships then developed with the Greeks, Romans, Phoenicians, Vikings and other cultures. Their use was widespread until the 19th century which saw the development of the steam engine, and more recently, the diesel engine. Sailing ships slowly declined in use and number until now, most sailing ships are used for recreational purposes.This picture shows the widespread use of sail for trading purposes.Picture of a sailing ship at a wharf with other ships in the background, by artist Rowland Hilder. Natural wood frame.Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, maritime painting by rowland hilder, painting of sailing ship -
Flagstaff Hill Maritime Museum and Village
Functional object - Suitcase, 1930-1945
The suitcase didn't catch on until the end of the 19th century, it was quite literally as a case for suits. A typical suitcase came equipped with an inner sleeve for storing shirts, and sometimes a little hat box on the side. But even in the early 20th century, the "dress-suit case" was only one of countless styles of container travellers could buy, from steamer trunks to club bags. By the late 19th century a significant point was reached in the history of transportation, it was the beginning of mass tourism, rather than travel for travels sake made use of by the wealthy in society. Travel wasn't just for the wealthy any more but everyone. Suitcases began as an afterthought in the luggage and leather goods business, but they soon became the very symbol of travel. An 1897 wholesale price list included the words "suitcase" only twice in a 20-page list of luggage types. In America a 1907 T. Eaton & Co. Catalogue, trunks took up a full page while suitcases share a page with club bags and valises. In a 1911 a United Company catalogue, now displayed around 40 per cent of the advertisements were for suitcases. Early suitcases were lighter and more portable than trunks, but they were still bulky by today's standards. Leather, canvas, wicker or thick rubbery cloth was stretched over a rigid wood or steel frame. Corners were rounded out using brass or leather caps and some had wooden rails running around the case. Until steamship travel declined during the mid-20th century, many of these types of the case were advertised as waterproof with some lightweight models marketed specifically to women. The item gives us a snap-shot as to how people undertook travelling during a time when undertaking a journey for pleasure at the end of the 19th century was mainly only for the wealthy. This time saw the beginnings of change from the wealthy in society being able to travel, to the onset of mass tourism. Along with this change in societal norms saw many innervations to the design of luggage as it became a fashionable item.Suitcase, brown canvas with three wooden reinforcing lateral rails running around the case, leather handle each end (one broken), two locks.. Maker Pettigrew & Stephens Ltd Glasgow. "A.T.Cox 354/3 Riversdale Rd Campberwell, Vic Australia" and "W.ON" painted over on each endflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, suitcase, -
Bendigo Military Museum
Equipment - SAW-TOOL KIT, 1943
547.1 Saw, cross cut, small, metal, folds into circle, holes for handles. 547.2 Bag, plastic, hold fold up saw. 547.3 Tool kit pouch, leather, brown colour, fitted to hold accessories, fold over lid attaches to a brass button. 547.4 File, metal, 3 corner, small. 547.5 Metal item, possibly for sharpening, has 2 grooves, fits handles. 547.6 & .7 Handles, wood with metal ring, fits saw and file etc.547.1 R.I. 1943 ↑33tools, saw kit, equipment, military -
Kiewa Valley Historical Society
Saw Logging, circa early 1900's
This item can be seen as a hand piece belonging to a logger or farmer spanning over one hundred or more years. The equipment was made to perfection as a hand tool and has not been improved upon since its introduction into the logging industry or farming fraternity. It can be used by one person or two (husband and wife or father and child). Its versatility is ageless. It can be used for domestic clearing of the paddocks, or for domestic fire places and stoves or commercial logging up until the 2000s (introduction of specific logging trucks that cut and treat the trees in one process).This item is very significant to the rural and logging regions within the Kiewa Valley. It has been used for domestic wood cutting and for industrial logging in the mid to late 1900s. It was used when clearing land for the SEC Hydro scheme and to allow for the introduction of the Mount Beauty construction workers' village (later developed into the town) The great advantage of this saw was that it uses only muscle power and can be located where ever a lumber "Jack" or property owner can venture. either by foot or by horse.This saw is a Warranted Superior One/Two Man Logging Saw. It has 68 teeth and is 42 inches long. At a position of one inch (2.5cm) from the end is a hole one inch down from the leading edge. There is another hole 45 cm in front of the handle. Both these holes are for a "helper handle" which when in use renders this logging saw fit for a two man operation. This is a cross cut saw for cutting down vertical trees (horizontal cut) The handle is made from wood and fastened to the blade by three heavy duty screws. The one helper handle stands 150mm high and has a 150mm wooden hand grip.The central screw has 25mm manufacturers' identification logo stamped "WARRANTED SUPERIOR".one or two man cross cut saws, forestry, timber industry -
Kiewa Valley Historical Society
Marking Gauge - Carpenter's Tool, c1925
Used from the mid 1920s to mark timber so that it could be cut with a saw. It was an essential tool for carpenters.Used by Alan Tyers who worked for the State Electricity Commission of Victoria on the Kiewa Hydro Electric Scheme.Carpenter's essential equipment. Used for marking timber so it can be cut with a saw. Wooden screw on the side allows the square wooden block to slide along the length of wood which is almost square at the end but with 2 flat sides and 2 rounded sides. Plated with 2 strips of brass on the square block. Sold for 1/3 in the 1920s. There is a nail through one end. carpenter, cabinet maker, secv, tool, marples, marking gauge -
The Beechworth Burke Museum
Photograph, 1936
... allowed a circular saw to be portable and set up at a logging site ...This automotive circular saw was designed to allow trees to be sawn into planks at the site they were felled, rather than requiring them to be carted to a lumber mill first. It was invented by Robert John (Bob) Pyle in 1936 and patented in 1937 (serial number 101975). This picture depicts Clarrie Howell (left) and Bob Pyle (right), standing with the sawbench between them. What was special about Bob’s new invention was that it not only allowed a circular saw to be portable and set up at a logging site, but that it allowed the circular saw to be run using the car motor, and that the saw could be detached, allowing the car to be used for carting or other purposes. This photograph is significant because it shows an early instance of an emerging technology, portable sawmills, and is evidence to the innovations that the people of Beechworth have achieved throughout history, as well Black and White rectangular photograph printed on matte photographic paper. Incription on cream paper stapled to bottom left of photographObverse: On left Clarrie Howell / Right Bob Pyle / with sawbench built by Bob Pyle / Patent 1936 / Rosalie Pyle has the original / [redacted]bob pyle, robert pyle, r j pyle, clarrie howell, howell, pyle, invention, patent, sawmill, saw, sawbench, wood, timber, forestry, automobile, car, 1930s, 1930s beechworth, industry, wooden, convenience, innovation -
Warrnambool and District Historical Society Inc.
Tools, Tenan Saws, Late 19th century
These hand saws belonged to Ernest Brighton Phillips (1875-1924). Born in Warrnambool, Ernest Phillips took up an apprenticeship in cabinet making at the Box Works in Warrnambool. By the late 1890s he had a furniture store and factory at the corner of Liebig and Koroit Streets. By the early 20th century Phillips had the largest furniture warehouse and factory in Victoria outside Melbourne. His products were sold all over Australia. Phillips and his family lived at ‘Heatherlie’ in Koroit Street. Today the site of the Phillips’ home contains flats for senior citizens in a complex known as ‘Heatherlie’. These tools are of interest as they belonged to Ernest Phillips, a prominent businessman in Warrnambool at the end of the 19th and the beginning of the 20th centuries. They are also examples of the type of tools used 100 years ago. These are two hand saws which belonged to Ernest Phillips of Warrnambool. They have a rounded wooden handle inserted via a metal plug into the end of a piece of wood which is slightly curved. Attached to the metal plug is a thin steel blade with a serrated edge. The blade is approximately the same size as the piece of wood. The blades are somewhat rusted.‘J. Marples & Sons, Sheffield’.ernest phillips, history of warrnambool -
Warrnambool and District Historical Society Inc.
Household, Hack saw, Early 20th century
The handle of this hammer looks to be home-made and to have been used as a household tool. Most homes still today include a small hammer as a household item. The provenance of this hammer is unclear but it possible that it is the hammer found at ‘Guthrie’, a house in Merri Street, Warrnambool that was demolished. ‘Guthrie’ was the home of the Dickson family, prominent in Warrnambool business circles. James Dickson, with his friend John Cramond, established a store in Warrnambool in the mid 19th century and this department store, known as Cramond and Dickson, was a prominent business in Warrnambool until its closure in 1973. James Dickson’s son and his family lived at ‘Guthrie’ and the hammer may have belonged to the Dicksons or another family connected to that property. This hammer has a metal head and a wooden handle. The top of the handle has a metal screw inserted and small slivers of the wood are missing. The end of the metal section is much worn.household tools, history of warrnambool -
Warrnambool and District Historical Society Inc.
Tools, Wood splitter, Early 20th century
This tool appears to have been hand-assembled. It would have been used on a farm or saw mill or any place of work or home requiring wood to be cut up. This tool has no known local provenance but is retained as an example of a tool used 100 years ago or more,This is a metal small axe or wood splitter with a wooden handle. The metal section is pitted and worn and the oval-shaped handle is partly split and worn. vintage hand tools, wood splitter, history of warrnambool -
Port of Echuca
Coloured Photograph, 04/03/1984
This photograph of the plaque on the side of the P.S Adelaide while she was a stationary exhibit in the Hopwood Gardens from 1963 until 1984 tells the story of her manufacture and her work life up until 1963. The P.S Adelaide was launched on 21st July 1866. It was owned by J.G.Grassie from Poon Boon Station and the Officer Family of Murray Downs Station Swan Hill. The Adelaide was named after the niece of the Officer Bros, Adelaide Blackwood. The shipwrights who built her was George Linklater. The Adelaide brought wool and passengers from the wool stations on the Murray and Darling Rivers down to the Echuca Wharf. In 1872 she was sold to David Blair & Sons. She was used to bring timber from the Barmah Forest to the Echuca Wharf. She did this work for the next 80 years. In 1953 she was tied up near the Mill and left In 1958 she went to Paringa South Australia to work in the sawmill industry again. In 1960 the Echuca Apex Club and The Echuca Historical Society raised enough funds to buy the P.S. Adelaide and return her to Echuca. In November 1963 she was lifted out of the water and placed in Hopwood Gardens as this was thought to be a way of preserving her. In 1984 it was decided to return her to the water to resume work as a passenger vessel. In that time the Port of Echuca and the Echuca Wharf had been restored as a Tourist Precinct. The P.S Adelaide is extremely significant as it it the oldest known wooden hulled paddle steamers in the world. She was built in Echuca in 1866 and still operates on the Murray River today. She has worked in the Wool Industry, the Timber Industry and the Tourist Industry.Coloured photograph showing the information sign which was attached to the side of the P.S Adelaide whilst she was a stationary exhibit in the Hopwood Gardens from 1963 until 1984.On the sign is written; " P.S Adelaide/built on the Murray at Echuca for Officer Grassie &Co. Of Poon Boon and Murray Downs stations. Launched 20th July 1866. The vessel is typical of the steamers trading in the era of the Riverina and Darling River trade of 1853 to the early 1900's and which had by 1872 established aEchuca as the second busiest port in Victoria. Worked in the Red Gum logging trade until 1958 under the ownership of the Murray River Sawmills Co. She was purchased by that company from David Blair Saw Miller of Echuca in 1861. 75ft. 4 inches X 12 ft.5 inches X 3 ft. 6 inches built of 3 inch red gum planking on an angle. Iron frames 2? X 2?5/6. 30 H.P. Nominal arc original and made by Fulton & Shaw of Melbourne. Twin cylinders. 14 bore. 16 stroke Stephenson's reversing gear controlled by Captain from the wheelhouse. Locomotive type red gum wood. Master, Mate, Engineer, Fireman, Cook, and Deckhand. p.s. adelaide, port of echuca, grassie, j.g, linklater, george, poon boon station, blair, david, murray river, darling river, logging industry, officer brothers., barmah forest, fulton & shaw, hutchinson, kevin, adelaide blackwood, murray downs station -
Port of Echuca
Black & white photograph
The P. S. Edwards was built in May 1875 by J. M. Webb, Echuca. Official number 73287, made of wood, with paddle wheels at the side. 78 gross tons, 27 nett tons. It was altered in 1916 , after cabin removed 48 gross ton. It had 7 different owners before being purchased by R. J. Evans, of Evans Bros. Saw Mill, Echuca, in 1919. The P. S. Edwards was sunk at Echuca in the spring of 1958 and then raised in January 1981 and then was being restored by Geoff Evans in 1985 (Parsons, Ronald. Ships of the Island Rivers. 3rd ed. 1996. p.67) The barge Ada was built in 1899 at Echuca by the Permewan Wright Company. The Ada hull was built of part wood and part steel, to protect the wool from becoming wet on the voyage down the Darling River to the Echuca Wharf. The Ada was used as a logging insider barge as well as a wool barge with the Pevensey on the Darling River.The P. S. Edwards has historical and social significance being a paddle boat built in Echuca. The P. S. Edwards was built in May 1875 by J. M. Webb, Echuca. It had 7 different owners before being purchased by R. J. Evans, of Evans Bros. Saw Mill, Echuca, in 1919. The P. S. Edwards was sunk at Echuca in the spring of 1958 "and as the mill was burnt in 1959 salvage was not attempted. She was raised in January 1981 and in 1985 was restored by Geoff Evans. While owned by Evans Bros, was used to bring red gum from the Barmah Forest to the sawmill in the barge Clyde." (Parsons, Ronald. Ships of the Island Rivers. 3rd ed. 1996. p.67) The barge Ada was significant because of the construction of the hull, being part wood and part steel. The Ada was used as an inside looking barge as well as a wool barge with the P.S Pevensey on the Darling River. The barge Ada is still on display at the slipway at the Port of Echuca. A black & white photograph of the P. S. Edwards towing the barge "Ada". A large tree is in the foreground and frames the boats. The boats are on a bend in the river. The barge appears to be laden with timber.In blue pen on reverse of photograph are written the words ? Adelaide (crossed out) Edwards & Ada barge ID4. Geoff Evans ? ( also crossed out). port of echuca, p. s. edwards, evans bros saw mills, ada barge, wool industry, p.s pevensey, darling river -
Parliament of Victoria
Portrait of Queen Victoria, Winterhalter, Franz Xaver (After), Queen Victoria, after Winterhalter, c.1859
Queen Victoria’s appreciation of German artist Franz Xaver Winterhalter (1805-1873) began after she saw portraits by him of other European monarchs. Accordingly, between 1842 and 1861 he made fifteen visits to England and painted over 100 portraits of Her Majesty, the royal family and other friends and dignitaries. In 1843 Winterhalter was commissioned to paint matching portraits of Queen Victoria and Albert, the Prince Consort. These originals hang in the Garter Throne Room at Windsor Castle and are part of the UK Royal Collection. Many legitimate copies of Winterhalter’s portrait were produced and presented to the Parliaments of the British Empire, including the Parliament of Victoria. Such copies are referred to as “After F. X. Winterhalter” and artists responsible include William Corden and John Prescott Knight. When creating copies, artists were not restricted by the size of the original portrait. Walterhalter’s original is 2.7m x 1.7m whereas copies can reach an impressive 4.5 metres in height. The portrait that hangs in Queens Hall at the Parliament of Victoria is not signed. Comparison with other copies of the work suggest that the Parliament’s painting may have been completed by William Corden. The Government Art Collection (United Kingdom), has a Queen Victoria copy in their collection and Parliament’s portrait has similar traits. A copy by John Prescott Knight which hangs in the Legislative Council in the Parliament of Tasmania is quite different, particularly with reference to the shape of the young Queen’s face, which is rounder in the Corden portraits.This portrait of Queen Victoria was presented as a gift by the British Government to the Parliament of Victoria in April 1860. Painted on fine linen supplied under Royal Warrant by the workshop Winsor and Newton, London, the frame has been embellished with elaborate wooden carvings. Framed portrait, oil on linen, of Queen Victoria. Victoria is posed in front of a curtain partially obscuring a building (possibly Buckingham Palace) in the background. Timber frame with a layer of gesso and decorative composition ornaments. There are rose, scotch thistle, clover leaf and Acanthus ornaments. A carved wood and composition element crown, resting on a tassled pillow sits on top of the frame.Canvas unsigned. Verso printed: ‘WINSOR AND NEWTON / Rathbone Place, London’. Embossed stamp into stretcher wood, stamped ‘Winsor and Newton’ in black ink.victoria queen of great britain, 1819-1901, winterhalter, franz xaver, 1805-1873, corden, william, queens hall, parliament of victoria -
Robin Boyd Foundation
Functional object - Rug
The Boyd's saw this type of floor covering at the Shelmerdine's house and liked it and purchased it. See also item F071.Cream wool with fringe."Woods Carpets Cleaning" 2 labels. Cleaned 11/9/96 and "1960".walsh st furnishings, robin boyd -
Tatura Irrigation & Wartime Camps Museum
Photograph
... using saw bench. POW's wood detail, Rushworth forrest during WW2 ...POW's wood detail, Rushworth forrest during WW2 watched by garrison soldiers.Black and white photo of workers using saw bench.internment camps, internment camp rushworth, pow's, garrison soldiers -
Maldon Vintage Machinery Museum Inc
Chainsaw, Maker's name "Outboard Marine Australia Pty. Ltd
"Pioneer" chainsaw with green housing. Pull start, no chain. Compliance plate on back (see Below) second plate on top.Compliance plate on back "Pioneer Saws / Model / 450 / Serial No. A10778 / Division of Outboard Marine Australia Pty. Ltd. / Bankstown NSW". Cast in relief on side "Pioneer & Pine Trees".machinery, wood cutting