The ship’s communication system that was used from the late 19th century to early-to-mid-20th-century is called an Engine Order Telegraph (E.O.T.) or ship’s telegraph. The system has two parts, the Bridge Section and the Engine Room Section. The Bridge Section is usually mounted on top of a pedestal, and the Engine Room Section is often attached to a vertical surface. The standard commands printed or stamped onto the dial are the directions of AHEAD and ASTERN, and the speeds of STOP, SLOW, HALF, and FULL. The ship’s pilot on the Bridge of a vessel sends his Orders for speed and direction to the to the Engine Room with the E.O.T. He moves the lever or levers, depending on the number of engines the ship has, to change the indicator on the Bridge Section’s dial to point in the new direction and speed of travel. This change causes the Orders to be duplicated on the Engine Room Section’s dial and a bell to signal the change at the same time. The engineer then adjusts the ship’s engines and steering equipment to follow the pilot’s Order. The manufacturer, A. Robinson & Co. Ltd of Liverpool, established his business in 1780 and continued until 1968 when the business was purchased by marine products maker Chadburns, established in London in 1870.This Engine Room section is part of a ship's telegraph communication system and represents marine technology used in the late-19th to mid-20th-century. Engine Room Section of a ship’s telegraph or Engine Order Telegraph (E.O.T.). The round brass dial has inscriptions stamped around its edge and centre. Red inlaid glass plates have inscriptions in white paint on them. The inscriptions are nautical terms for direction and speed and include the maker’s details. A rotating pointer is joined to the centre of the dial. The maker is A. Robinson & Co. Ltd of Liverpool. Stamped: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP”, “AHEAD / ASTERN” Printed: “FULL / HALF / SLOW / STOP / FULL / HALF / SLOW / STOP” Stamped on the dial: “A. ROBINSON & CO. LTD / MANUFACTURERS / LIVERPOOL”flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, marine technology, marine communications, engine order telegraph, e.o.t., ship’s telegraph, bridge section, engine room section, ship’s engine telegraph section, marine telegraph, a. robinson & co. ltd, liverpool

"Grip" bale fasteners,The Hurst & Hughes Pty Ltd, 35 Skene Street, Geelong, Victoria. Donated from the estate of the donors' father who had an involvement through the scouting movement with the Hurst family who invented bale clips."Grip" bale fasteners,The Hurst & Hughes Pty Ltd, 35 Skene Street, Geelong, Victoria."Grip" Bale Fasteners/ The Hurst & Hughes Pty Ltd, 35 Skene Street, Geelong, Victoria....shearing wool bales, hurst and hughes pty ltd, wool bale clips, hurst, mr harold e., shearing, wool bales

In 1938 William Edward Mc Pherson established Australian Abrasives Pty. Ltd., manufacturing grinding and filing tools, blades and other similar hardware items. This sharpening stone is made of silicon carbide, which is a very hard synthetic product. The compound was discovered in America in 1981 by Edward Achison whilst trying to make artificial diamonds from a mixture of clay and powdered coke. Initially the substance was used for polishing gems then it went on to be used as an abrasive in sandpapers, grinding and sharpening stones and cutting tools. This sharpening stone was donated to Flagstaff Hill Maritime Village by the family of Doctor William Roy Angus, Surgeon and Oculist. It is part of the “W.R. Angus Collection” includes historical medical equipment, surgical instruments and material once belonging to Dr Edward Ryan and Dr Thomas Francis Ryan, (both of Nhill, Victoria) as well as Dr Angus’ own belongings. The Collection’s history spans the medical practices of the two Doctors Ryan, from 1885-1926 plus that of Dr Angus, up until 1969. ABOUT THE “W.R.ANGUS COLLECTION” Doctor William Roy Angus M.B., B.S., Adel., 1923, F.R.C.S. Edin.,1928 (also known as Dr Roy Angus) was born in Murrumbeena, Victoria in 1901 and lived until 1970. He qualified as a doctor in 1923 at University of Adelaide, was Resident Medical Officer at the Royal Adelaide Hospital in 1924 and for a period was house surgeon to Sir (then Mr.) Henry Simpson Newland. Dr Angus was briefly an Assistant to Dr Riddell of Kapunda, then commenced private practice at Curramulka, Yorke Peninsula, SA, where he was physician, surgeon and chemist. In 1926, he was appointed as new Medical Assistant to Dr Thomas Francis Ryan (T.F. Ryan, or Tom), in Nhill, Victoria, where his experiences included radiology and pharmacy. In 1927 he was Acting House Surgeon in Dr Tom Ryan’s absence. Dr Angus had become engaged to Gladys Forsyth and they decided he further his studies overseas in the UK in 1927. He studied at London University College Hospital and at Edinburgh Royal Infirmary and in 1928, was awarded FRCS (Fellow from the Royal College of Surgeons), Edinburgh. He worked his passage back to Australia as a Ship’s Surgeon on the on the Australian Commonwealth Line’s T.S.S. Largs Bay. Dr Angus married Gladys in 1929, in Ballarat. (They went on to have one son (Graham 1932, born in SA) and two daughters (Helen (died 12/07/1996) and Berenice (Berry), both born at Mira, Nhill ) According to Berry, her mother Gladys made a lot of their clothes. She was very talented and did some lovely embroidery including lingerie for her trousseau and beautifully handmade baby clothes. Dr Angus was a ‘flying doctor’ for the A.I.M. (Australian Inland Ministry) Aerial Medical Service in 1928 . Its first station was in the remote town of Oodnadatta, where Dr Angus was stationed. He was locum tenens there on North-South Railway at 21 Mile Camp. He took up this ‘flying doctor’ position in response to a call from Dr John Flynn; the organisation was later known as the Flying Doctor Service, then the Royal Flying Doctor Service. A lot of his work during this time involved dental surgery also. Between 1928-1932 he was surgeon at the Curramulka Hospital, Yorke Peninsula, South Australia. In 1933 Dr Angus returned to Nhill and purchased a share of the Nelson Street practice and Mira hospital (a 2 bed ward at the Nelson Street Practice) from Dr Les Middleton one of the Middleton Brothers, the current owners of what previously once Dr Tom Ryan’s practice. Dr Tom and his brother had worked as surgeons included eye surgery. Dr Tom Ryan performed many of his operations in the Mira private hospital on his premises. He had been House Surgeon at the Nhill Hospital 1902-1926. Dr Tom Ryan had one of the only two pieces of radiology equipment in Victoria during his practicing years – The Royal Melbourne Hospital had the other one. Over the years Dr Tom Ryan had gradually set up what was effectively a training school for country general-practitioner-surgeons. Each patient was carefully examined, including using the X-ray machine, and any surgery was discussed and planned with Dr Ryan’s assistants several days in advance. Dr Angus gained experience in using the X-ray machine there during his time as assistant to Dr Ryan. When Dr Angus bought into the Nelson Street premises in Nhill he was also appointed as the Nhill Hospital’s Honorary House Surgeon 1933-1938. His practitioner’s plate from his Nhill surgery is now mounted on the doorway to the Port Medical Office at Flagstaff Hill Maritime Village, Warrnambool. When Dr Angus took up practice in the Dr Edward and Dr Tom Ryan’s old premises he obtained their extensive collection of historical medical equipment and materials spanning 1884-1926. A large part of this collection is now on display at the Port Medical Office at Flagstaff Hill Maritime Village in Warrnambool. In 1939 Dr Angus and his family moved to Warrnambool where he purchased “Birchwood,” the 1852 home and medical practice of Dr John Hunter Henderson, at 214 Koroit Street. (This property was sold in1965 to the State Government and is now the site of the Warrnambool Police Station. and an ALDI sore is on the land that was once their tennis court). The Angus family was able to afford gardeners, cooks and maids; their home was a popular place for visiting dignitaries to stay whilst visiting Warrnambool. Dr Angus had his own silk worm farm at home in a Mulberry tree. His young daughter used his centrifuge for spinning the silk. Dr Angus was appointed on a part-time basis as Port Medical Officer (Health Officer) in Warrnambool and held this position until the 1940’s when the government no longer required the service of a Port Medical Officer in Warrnambool; he was thus Warrnambool’s last serving Port Medical Officer. (Masters of immigrant ships arriving in port reported incidents of diseases, illness and death and the Port Medical Officer made a decision on whether the ship required Quarantine and for how long, in this way preventing contagious illness from spreading from new immigrants to the residents already in the colony.) Dr Angus was a member of the Australian Medical Association, for 35 years and surgeon at the Warrnambool Base Hospital 1939-1942, He served as a Surgeon Captain during WWII1942-45, in Ballarat, Victoria, and in Bonegilla, N.S.W., completing his service just before the end of the war due to suffering from a heart attack. During his convalescence he carved an intricate and ‘most artistic’ chess set from the material that dentures were made from. He then studied ophthalmology at the Royal Melbourne Eye and Ear Hospital and created cosmetically superior artificial eyes by pioneering using the intrascleral cartilage. Angus received accolades from the Ophthalmological Society of Australasia for this work. He returned to Warrnambool to commence practice as an ophthalmologist, pioneering in artificial eye improvements. He was Honorary Consultant Ophthalmologist to Warrnambool Base Hospital for 31 years. He made monthly visits to Portland as a visiting surgeon, to perform eye surgery. He represented the Victorian South-West subdivision of the Australian Medical Association as its secretary between 1949 and 1956 and as chairman from 1956 to 1958. In 1968 Dr Angus was elected member of Spain’s Barraquer Institute of Barcelona after his research work in Intrasclearal cartilage grafting, becoming one of the few Australian ophthalmologists to receive this honour, and in the following year presented his final paper on Living Intrasclearal Cartilage Implants at the Inaugural Meeting of the Australian College of Ophthalmologists in Melbourne In his personal life Dr Angus was a Presbyterian and treated Sunday as a Sabbath, a day of rest. He would visit 3 or 4 country patients on a Sunday, taking his children along ‘for the ride’ and to visit with him. Sunday evenings he would play the pianola and sing Scottish songs to his family. One of Dr Angus’ patients was Margaret MacKenzie, author of a book on local shipwrecks that she’d seen as an eye witness from the late 1880’s in Peterborough, Victoria. In the early 1950’s Dr Angus, painted a picture of a shipwreck for the cover jacket of Margaret’s book, Shipwrecks and More Shipwrecks. She was blind in later life and her daughter wrote the actual book for her. Dr Angus and his wife Gladys were very involved in Warrnambool’s society with a strong interest in civic affairs. He had an interest in people and the community They were both involved in the creation of Flagstaff Hill, including the layout of the gardens. After his death (28th March 1970) his family requested his practitioner’s plate, medical instruments and some personal belongings be displayed in the Port Medical Office surgery at Flagstaff Hill Maritime Village, and be called the “W. R. Angus Collection”. W.R. Angus Collection is significant for still being located at the site it is connected with, Doctor Angus being the last Port Medical Officer in Warrnambool. The collection of medical instruments and other equipment is culturally significant, being an historical example of medicine from late 19th to mid-20th century. Dr Angus assisted Dr Tom Ryan, a pioneer in the use of X-rays and in ocular surgery. Sharpening stone, part of the W.R. Angus Collection. Grey, rectangular block of silicon carbide made from two pieces of different densities joined together. Sharpening stone is in green and black cardboard box with lid. Maker is Australian Abrasives Pty Ltd. Circa mid 1900’s.Box text "AUSTRALIAN ABRASIVES Pty Ltd SHARPENING STONE" and "SILICON CARBIDE" and "NO. 108 / COMB", "8" x 2" x 1" "flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, dr w r angus, dr ryan, sharpening stone, australian abrasives pty ltd, sharpening tool, metal working equipment

Sunshine biscuits were made in Ballarat from 1921. During WW11 Sunshine biscuits devoted 80 percent of its output to army services. The company was twice devastated by fire. In 1923 the factory was completely destroyed and was rebuilt as a more modern factory on the same site. In 1939, a deliberately lit fire demolished the workshop. Sunshine biscuits continued to be sold until 1991. Biscuits were sold by weight from a large tin in the grocer's shop.This tin seems to be a commercial tin used in a grocery shop. It would have been used in an Orbost grocery store e.g. Dicken's, Baughhaust's or Herbert's.Biscuits were once sold by weight from a large tin in the grocer's shop.This tin seems to be a commercial tin used in a grocery shop. It would have been used in an Orbost grocery store e.g. Dicken's, Baughhaust's or Herbert's.Large rectangular commercial biscuit tin, made from pressed metal, with a lid. There is a paper label on the front which details the contents, and manufacturer details. It has a colourful label which is in poor condition. On label - in a dark blue banner SUNSHINE. Left hand side vertically BALLARAT PRODUCTS LIMITED. Below the SUNSHINE banner - Sweet Assorted, Superior biscuitssunshine-biscuits food biscuits container tin

2 VIEWS OF CLUNES TOWN HALL 1 VIEWS OF DISTRICT HOSPITAL, CLUNES 2 VIEWS OF FRASER STREET, CLUNES 2 VIEWS OF CLUB HOTEL, CLUNES 1 VIEW OF GOLD MONUMENT 1 VIEW OF TULLAROOP RIVER, CLUNES 1 VIEW OF INTERNET HOSIERY CO. CLUNES. (FORMERLY SOUTH CLUNES SCHOOL)SMALL MANILLA ENVELOPE CONTAINING TEN PHOTOGRAPHS - TOWN HALL CLUNES,DISTRICT HOSPITAL CLUNES, FRASER STREET CLUNES, CLUB HOTEL CLUNES, INTERKNIT HOSIERY COY. LTD. CLUNES, MONUMENT AT CLUNES, TALLAROOP RIVER CLUNESPrinted on envelope in blue ink; Valentine's Snapshots, Eight Real Photographs, Clunes. Published by The Valentine Publishing Co. Pty. Ltd. Melbourne, Sydney and Adelaidelocal history, photography, photographs

Sultana worsted Axminster 27" carpet body sample made by John Crossley & Sons Ltd. Related to border sample 88.0047 (old registration number). Part of ten piece collection originally presented to the Queensland Museum by Mr Doug Glanville.Sultana worsted Axminster 27" carpet body sample made by John Crossley & Sons Ltd. Sultana worsted Axminster 27" carpet body sample made by John Crossley & Sons Ltd.Sultana worsted wool Axminster linen back manfd. 1893 4 27" body carpet J.C & Sons Ltd Halifax Englandweaving, john crossley and sons, carpet

Woollen crochet yarn produced by F.W. Hughes Pty Ltd, Sydney.'Twin-Prufe' crochet wool, produced by F.W. Hughes Pty Ltd, Sydney.Twin-Prufe / MOTH / PROOF / SHRINK / PROOF / CROCHET / WOOL / AN F.W. HUGHES Product ALL WOOL / GUARANTEED PERMANENTLY / MOTHPROOF / GUARANTEED SHRINKPROOF / IF WASHED AS A WOOLLEN / 2354 / F.W. HUGHES PTY. LTD. / SYDNEY - AUSTRALIAhandicrafts, textile mills, f.w. hughes pty ltd

Westclox had a highly successful factory in Scotland situated in the Vale of Leven Industrial Estate, in Dumbarton, around twenty miles from the City of Glasgow. Westclox had originally planned to start production in Scotland in 1939 but the War intervened and it was not until 1948 that they were able to fully commission their factory in Dumbarton. Westclox Scotland produced its first clock on the 21st September 1948; a spring wound alarm with a 4 inch dial. The Westclox factory in Scotland was a full manufacturing plant with all their clocks assembled from start to finish with only the basic raw materials being brought in by outside suppliers. 95% of the staff were local people and the firm trained their employees from scratch to a high level of skill and had an annual apprenticeship for toolmakers and classes in horology. By 1949 Westclox Scotland were making 10,000 clocks a week, and by 1950, 1,000,000 clocks had been produced since its opening. No home in the Dunbartonshire Vale was without at least one Westclox clock, nor any raffle complete without a clock as one of the prizes! Many of these clocks are still around today. So successful was the Dumbarton factory that in the mid 1950’s Westclox had to expand into adjoining buildings. The factory then added watches to what they made as well as timing devices for other sectors. By the mid 1960’s, employment levels at the Scottish plant were around 1100. Over a third of the clocks manufactured in Scotland were exported to some 110 countries across the globe. Difficult times came in 1967/68 when 400 workers were laid off and the future of the plant was in doubt primarily due to cheap clocks from the then communist countries. However, strong petitions to the UK Government produced the passing of an anti-dumping law allowed production from the factory to pick up. In 1968 General Time was bought out by Talley Industries, which was best known as a manufacturer of timing equipment, such as factory time clocks to various industries. Westclox in Scotland enjoyed several boom years under the then Managing Director, John Santos. Westclox Scotland in October 1974 hosted a Space Seminar for the Astronaut, Neil Armstrong and British Astronomer, Sir Patrick Moore. Both visited the Scottish factory to promote the introduction of Quartz time-keeping. In 1976 the Westclox plant in Dumbarton became the Headquarters of General Time (International Operations) Ltd. John Santos retired from General Time and Westclox in the early 1980s and by 1988 the future of Westclox in Scotland was almost over. The advent of Quartz clock technology, developed largely by General Time for use in the Apollo 11 Command Module, resulted in the reduction of mechanical clock production and sales, and the factory fully closed in 1988.The Westclox factory building in Dumbarton has been converted and is now home to many thriving small businesses. The item marks a time when clock production in the United Kingdom was at it’s peak producing clocks for sale in over a 110 countries, they were keenly priced and available to all. The company had many innervation's during it’s life regards clock and later wrist watch making. In 25 years the factory had produced over 50 million clocks, yet it was perhaps inevitable with the advent of Quartz technology that was ironically evolved, largely by General Time for use in the Apollo 11 Command space Module, that would ultimately herald the end of the mechanical clock.Wooden bedroom alarm clock small painted brown with a criss cross pattern in gold and a white enamel face roman numerals & a glass front, clock case is of a fancy design. Inscribed on face "Made by Westclox Ltd Scotland" .flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, clock mantle, clock, mantle clock, westclox ltd, horology, clock industries

Metal money boxes shaped like common familiar objects became popular in the 18th century. In the 20th century, they were used to promote and advertise events and businesses. In the 1950s metal money boxes shaped like a bank building were given away to children by their parents' bank to encourage them to save money. This metal money box was produced for the company of OXO Ltd of London. It was made specifically as a souvenir of the Coronation of King George VI of England, which happened on May 12, 1937. OXO Ltd. still makes OXO stock cubes, which contain a concentrated meat extract. The cubes are used to flavour soups, gravy, casseroles and other food recipes to enhance their flavour. The cubes are removed from their foil wrapper then crumbled into the dish and mixed with the ingredients. Chemist Justus von Liebig worked with engineer George Gilbert of Uruguay to produce Liebig’s Extract of Meat, the forerunner of OXO . In the late 1890s, OXO produced a liquid form of the meat extract and in 1899 registered the OXO trademark worldwide, and in 1900 in the UK. In 1910 the OXO 'penny' cube was in production and proved very popular. The money box is significant for its connection to British Monarch, King George IV, who reigned from 1932-1952. It is also significant for its connection to the OXO cube, a very well knon brand of food additive from the mid-19th century to current times.Souvenir money box, oval cylinder with domed, pull-off lid and framed coin slot, with seams on each side. It once contained six OXO Cubes. The red tin with gold tin has the Royal Insignia of King George VI and Elizabeth on one side and the Royal medallion-style portrait of King George VI and Elizabeth on the other side. There is an inscription on the base and floral decorations on the sides. It was produced for OXO Ltd, Thames House, London, England, to commemorate the coronation of King George V1 and Elizabeth on May 12th 1937.Logo, Royal Insignia: "[Crown] over "G VI R" Medallion-style Portrait image: "GEORGE VI AND ELIZABETH MAY 12TH 1937" around " (Image of King George VI and Elizabeth) " Printed on base: "CORONATION / SOUVENIR MONEY BOX / CONTAINING / 6 OXO CUBES / BRAND / OXO LTD., THAMES HOUSE, / LONDON, ENGLAND."flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, money box, money safe, commemorative money box, coronation king george iv, 1937, vintage money box, oxo cube, numismatics

Earthenware is lightly fired, readily absorbs water if not glazed, and does not allow light to pass through it. Coarse earthenware is made from clay and grog (ground up fired pot). There are two main types of glazed earthenware: One is covered with a transparent lead glaze; when the earthenware body to which this glaze is applied has a cream colour, the product is called creamware. The second type, covered with an opaque white .in glaze, is variously called tin-enamelled, or tin-glazed, earthenware, majolica, faience, or delft. G&S marking could be Grove & Stark, Longton, England (1871-1884). In the 19th century, J. & G. Meakin ,1851 based in Hanley, Stoke-on-Trent, Staffordshire, was known for the vast quantities of cheap ironstone china it produced for the domestic English market and for export to Australia, Canada, New Zealand and the United States. Grove & Stark were taken over by Meakin early 20thC The Mark could also be Gibson & Sons (Ltd), were notably manufacturers of earthenware Burslem, Stoke-on-Trent. Founded around 1885 and traded until the mid 1970's. They were previously Gibson, Sudlow & Co. Manufactured between 1885 to 1905. Small earthen-ware, black-glazed tea-pot. 8 sided. The body of the tea-pot is decorated with hand-painted gold flowers and raised cream flowers. The lid is also hand -painted with green leaves and flowers. This floral pattern is named "Garland" The lid is not of the same pattern as the base. The spout was broken when brush tailed possum entered Cottage via chimney 27/4/2014. Can be repairedOn the base of the tea-pot. Makers Mark is G & S. "Garland". (Pattern), Rg. No. 175153. Also 'Made in England'. Under glaze there is the word: England.crockery, earthenwarre, gibson & son ltd, grove & stark ltd, pioneers, early settlers, bentleigh, market gardeners, moorabbin, cheltenham, pottery, stoke- on - trent, england, longton, burslem, wedgwood

This nameplate was attached to the steel steamer Matthew Flinders I, a Suction Hopper Dredge used for pumping up sit and sanding from seabeds. It was donated by the Marine Engineer, Neville Dodds, from Ports and Harbours, from the Matthew Flinders I. The Matthew Flinders was constructed by Morts Dock & Engineering Coy. Ltd in Sydney, New South Wales. Identified as Ship No. 40, the dredge had twin screw engines that were made in Sydney. Its gross tonnage was 1180. It was launched on July 15th, 1916, and registered in 1917 at the Port of Melbourne by the owner, the Department of Public Works in Victoria. Unlike bucket dredges, the Matthew Flinders did not use permanent moorings but instead had bow and stern anchors. It travelled forward on the bow anchor, taking up a strip of even-depth wilt from the bed below. A local newspaper noted that the Matthew Flinders has many advantages that were especially useful for its work at Warrnambool. Warrnambool Harbour had been experiencing silting and sanding for many years. The problem continued even after the construction of the Breakwater in 1890, which was overseen by New Zealand engineer Arthur Dudley Dobson. Melbourne’s Department of Ports and Harbours sent the new Matthew Flinders to dredge the heavy silting in the Warrnambool Harbour in May 1919. This work was previously done by the smaller dredge, the Pioneer. However, after a month of work, the Matthew Flinders was returned to Melbourne for alterations to make it suitable for work in the heavy seas it experienced at Warrnambool. Both dredges were sent up from Melbourne when required over the years to periodically attend to the silting in the Harbour, but the Matthew Flinders was preferred because of its efficiency. It was still dredging the Harbour even in July 1938. The ship’s original master was J G Rosney. In February 1922 Percy Taylor from Ports and Harbours joined the Matthew Flinders as a Mate. 1923 the master in charge was Captain Dunbar. In August 1926 Percy Taylor was appointed as her Master and was later transferred to the Pioneer as Master in 1933. 1930 the dredges were no longer required as the Harbour was no longer suitable as a port. However, one source notes that the Matthew Flinders was still dredging the Harbour in 1938.This nameplate is significant for its association with the suction hopper dredge Matthew Flinders I, which was used to remove the build-up of silt and sand from the Warrnambool Harbour, allowing shipping activities to continue to operate in the Port of Warrnambool. The nameplate identifies the vessel and shows that it was built in Australia in the early 20th century for use within Australia. The need for dredging in the Warrnambool Harbour was a serious and ongoing problem, as silting continued to happen after a series of measures were taken to try and resolve the issue. Eventually, the Harbour could no longer function successfully as a port.Brass nameplate, rectangular with cut-away corners and moulded text, mounted with screws on timber. The plate is from a vessel, the dredge Matthew Flinders I, ship no. 40, built by Morts Dock & Engineering Coy Ltd in Sydney, and registered in 1917. A small rectangular engraved plaque below the nameplate gives further details of the ship and the donor.On nameplate: "MORTS DOCK / & / ENGINEERING COY. LTD. / SHIP BUILDERS / SYDNEY 1917 / SHIP NO 40" On small plaque: "Donated by / NEVILLE DODDS / PORTS & HARBOURS / MARINE ENGINEER / EX "MATTHEW FLINDERS I"flagstaff hill, warrnambool, maritime village, maritime museum, flagstaff hill maritime museum & village, shipwreck coast, great ocean road, dredge, mathew flinders i, steel steam ship, twin screw engines, nsw, state of victoria, suction hopper, public works melbourne, warrnambool harbour, lady bay, sanding, silting, breakwater, morts dock & engineering co ltd, captain dunbar, ship no. 40, niville dodds, ports & harbours, marine engineer, marine technology, ship relic, percy taylor, matthew flinders, pioneer

Trove : The Courier-Mail, Brisbane, Queensland Friday 15 December 1938, page 7, Article : New Canning Company A company under the name of Tassell United Cannery Pty., Ltd., is being formed to operate a pineapple cannery in the new year. It proposes to acquire the business of Glassop and Son, proprietors of Tassell Products, and may engage in inter-State and export trade. It is stated by the promoter that growers and small canners of pineapples fear that the industry may become monopolised and that the new company is being formed to combat any such tendency. TROVE : The Courier-Mail, Brisbane, Queensland Friday 29 December 1950, page 3, Article : Mr. Glassop dies A well-known Brisbane citizen. Mr. S. J. Glassop, 74, has died. He was founder and managing director of Tassell United Cannery, Pty., Ltd. For many years Mr. Glassop was associated with Messrs. R. W. Thurlow and Co., Ltd., Brisbane, and later left this firm to open his own business on the Darling Downs. He later returned to Brisbane to enter the manufacturing business. He was actively connected with the business until his death. Round olive- amber coloured glass bottle with wide neck and shoulder tapering toward base then flaring out again at base. Embossed text on sides and number On side, 'THIS BOTTLE IS THE PROIPERTY OF TASSELL UNITED CANNERY PTY LTD BRISBANE'. On base 'B146', 'AGM'.fruit, cannery, glassop, tassell, pineapple

Whittingslowe Engineers Ltd of Adelaide was an Australian manufacturer. A patent for the 'Hot-Glow' water bottles was issued to the company in 1945. An advertisement in 1946 (Morning Bulletin, 19/06) describes the bottles as all metal and advertised their price as 11/6 each.These two hot water bottles are fine and rare examples of products produced by a major Australian engineering and manufacturing company.Two brass cylindrical hot water bottles, manufactured by Whittingslowe. The label of the manufacturer and distributor is on the from of each bottle on a red and gold label."HOT-GLOW' WATER BOTTLES / WHITTINGSLOWE MANUFACTURER / ? WOOD PTY LTD MELBOURNE AND SYDNEY / AUSTRALIAN DISTRIBUTORShot water bottles, domestic objects, whittingslowe - manufacturers

Used by first Warrnambool Cheese and Butter Factory Company Ltd Field Officer, Bruce McLaren, for on-farm testing in the Allansford area to check the amount of suction in milking machines.Phillips Rurakura Vacuum Recorder in a wooden box with lid, metal hinges and fastening clip, screw adjustment and name plate on outside. Inside has a clockwork-operated recorder with pen device to roll of paper.Internal: Trade mark Empel E.M.P. Engineers Ltd PO Box 5125, Hamilton, NZ Aust. Pat. 209 510. NZ Pat. 112 486. External: Empel Phillips Ruakura Type Vacuum recorder, Makers E.M.R. Engineers Ltd. PO Box 5125, Hamilton NZ

Michel lipsticks were created by an American company led by Georgette Michel which regularly advertised their products in women's magazines in the 1940s and 1950s. The lipsticks were manufactured [under licence?] by DHA Laboratories (Drug Houses Australia) Pty Ltd which had been established In 1930, as a holding company combining Bickford's with a number of similar Australian companies representing all states except Tasmania. Most items produced by DHA Laboratories were pharmaceuticals. It is not known whether the holding company manufactured other cosmetics apart from the Michel line.Intact, and unused packet of Australian produced lipsticks produced in the 1940s or 1950sPack of Michel lipsticks, containing 10 of the 12 original lipsticks. The colour is cyclamen. Exterior of packet: "Michel Lipstick / Stays on longer / Manufactured by D.H.A. Laboratories Pty Ltd, Melbourne | Regd Users of Trademark / One dozen Popular size"cosmetics, lipsticks, michel - dha laboratories pty ltd

The Villa Alba Museum is cultural institution committed to the collection, study and display of 19th century interior decorative finishes, and the components of 19th and 20th century interior decoration. Most rooms in this historically and aesthetically significant house have stone (typically marble) fireplaces that are inset with plain and decorative tiles produced by the company of Mintons Ltd.Digital photograph of the pattern of plain hearth tiles in the fireplace of the dining room at Villa Alba. The square majolica plain tiles, positioned under where the original cast iron grill sat, are in shades of brown, green and blue. The tiles were produced by Mintons Ltd.fireplaces, mintons, mintons - tiles, villa alba -- dining room

TIN OF SWALLOW & ARIELL LTD. PLUM PUDDING, INTACT. SMALL HOLE IN THE BOTTOM, SEALED WITH DUCT TAPElocal history, domestic item, food and drink consumption

William Thomas George was born in Birmingham in 1884 and was a tin plate worker. He and his wife Ellene had a son Leslie Thomas George. The firm W T George & Co was formed sometime later. In 1939 his firm produced ship lamps. The Patent Number GB546575 on the lamp's plate was assigned to Leslie Thomas George in 1941 for improvements in, or relating to, ships' lanterns. From that time the patent number was affixed to their namufactured Meteorite lights. The ship navigation lamp is important as an example of the evolution of marine safety technology. Countries began passing laws and regulations in the 1830s that required ships to show navigation lights at night or in poor weather. From the late 1840s colours were standardised; red for portside of the vessel and green for starboard, a white masthead light, and a white light at anchor. By 1914 the International Convention for the Safety of Life at Sea was formed and continues, with decisions and notifications on improvements and changes.. Lamp; Portside ship's lamp is rounded in the front with two flat sides coming to a point at the rear. Glass has circular ridging. Metal handle with lid and clasp. The reflector has red colouring. Inscribed on fixed plates on the front, with maker's details and Patent number. This Meteorite lantern was made by W T George and Co Ltd, of Birmingham. "Port" "W T George and Co Ltd" "Sherlock Street Birmingham" "Meteorite 68990 Patented No 546575 and others pending"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, portside ships lamp, portside, port lamp, ship's lamp, marine lamp, navigation lamp, w t george & co, coloured lens, red lens, ship fitting, marine technology, navigation light, signal lamp, leslie thomas george, gb546575, patent gb546575, meteorite, lantern, lamp, light

This camera is a folding one, the Ensignette No 2 model made by the British firm of Houghtons Ltd which was originally a glass warehouse founded in 1834. The firm of George Houghton and Sons, dating from the late 19th century, established their camera business at Ensign House in London in 1903 and the Ensignette No 2, designed by a Swedish engineer, was introduced in 1912. Eastman Kodak of America produced a film for this model. This camera was a popular one with amateur photographers and the general public, being affordable, compact and easy to use. This camera is retained as an example of a British-made folding camera dating from nearly 100 years ago. It will be useful for display..1 This is a black metal camera which is rectangular in shape. It is a strut folding rollfilm camera with a lens that is folded inside in a thin leather concertina or bellows covering. It has the maker’s name and logo etched into the front of the camera. The logo is a flag with the British Union Jack in one corner and the word ‘Ensign’ inside the flag. The metal on the back of the camera is rusted. .2 This is a brown leather cover for the folding camera described above. It has a top lid flap which closes with a metal stud and a leather handle stitched on to the sides of the case. The cover is much worn and scuffed. Ensignette No 2 Ensign British Made Made by Houghtons Ltd England vintage cameras

This book/magazine is a record of the company's tasks in WW11. It acknowledges the "debt owed to the armed forces involvement and role in defeating the enemy". The Australian operations of this company were originally founded by Hugh V. McKay in the 1890s. In 1906, H.V. McKay moved his manufacturing operations from Ballarat to Braybrook Junction (later Sunshine) on the western outskirts of Melbourne. In 1921 the company became H.V. McKay Pty Ltd. In 1930 it merged with the Australian operations of the Canadian agricultural implement and tractor manufacturer Massey Harris, to become H.V. McKay Massey Harris Pty Ltd. Throughout World War II H.V. McKay Massey Harris exported over 20,000 Sunshine drills, disc harrows and binders to England to facilitate the increase in food production. (ref Museum Victoria, Wickipedia)Inside this magazine is a photograph of a sprocket similar to that made by Orbost Motor Works during WW11. (Registration No 2001)A large stapled cardboard covered magazine with a tan coloured cover. On the front cover in dark brown print at the bottom is a rising sun with "H. V. McKay Massey Harris Pty Ltd Australia" underneath it. At the top in large font is 1939 1945. It contains coloured photographs and text. massey-harris

Two machinery plan layouts for Mimosa Wool & Textiles Pty Ltd in Hobson's Road, Kensington.1617.1 Rectangular blue paper with white lined plan drawing and white text 1617.2 Rectangular blue paper with white lined plan drawing1617.1 Front: Final Plan / PLAN OF MACHINERY LAYOUT / MIMOSA WOOL & TEXTILES PTY LTD / HOBSON'S ROAD KENSINGTON / BY MESSRS J DYSON & SONS / SOUTH GEELONG / Scale 3/32" - 1.0"factory, machinery, wool, textiles, mill, kensington, south geelong, plans, drawings, blueprint, layout, mimosa, j. dyson and sons pty ltd

A postcard that was produced by Nucolorvue Productions Pty. Ltd. as a souvenir of Marysville in Victoria.A postcard that was produced by Nucolorvue Productions Pty. Ltd. as a souvenir of Marysville in Victoria.THE AUSTRALIAN KOALA This harmless, quaint creature is/ one of Australia's most well-/ known animals. NU-COLOR-VUE/ OF/ AUSTRALIA BA208/ RP110 POST CARD NUCOLORVUE PRODUCTIONS PTY. LTD./ (03) 560 1788 PRINTED IN AUSTRALIAkoala, marysville, victoria, nucolorvue productions, postcard, souvenir

The Villa Alba Museum is cultural institution committed to the collection, study and display of 19th century interior decorative finishes, and the components of 19th and 20th century interior decoration. Most rooms in this historically and aesthetically significant house have stone (typically marble) fireplaces that are inset with plain and decorative tiles produced by the company of Mintons Ltd.Digital photograph of the pattern of decorative hearth tiles used the fireplace of the morning room at Villa Alba. The patterns within the decorative tiles are self-contained or show their pattern when assembled with matching tiles. The multicoloured tiles have a grey or maroon background. The tiles were produced by Mintons Ltd.fireplaces, mintons, mintons - tiles, villa alba -- morning room

"The Kew Advertiser , published by WD Vaughan Pty Ltd, commenced publication in January 1926 and, before the year's end, a modern printing plant had been established at 128 Denmark Street (demolished). This later became the nerve centre for publication of four other local newspapers: The Hawthorn Standard (1932), the Eastern Suburbs Advertiser (1934), the Coburg Courier (1935) and the Brunswick Sentinel (1936). The last two were later sold to another publisher, and the remaining three merged in 1959 to form the Eastern Suburbs Standard. This, in turn, continued under that name until 1974, when it merged with a counterpart from Doncaster, the Whitehorse Standard, and then carried on (under various names) until 1980." (Source: City of Boroondara : Thematic Environmental History, p. 75)Kew Newspaper produced in 1941 by W D Vaughamn Pty Ltd. The newspaper was printed at his offices in Denmark Street. The banner headline claims that it had a distribution of 6,000 copies.the kew advertiser, newspapers -- kew (vic), wd vaughan pty ltd

.01-.09 Nine copies of "Advance" - a journal of interest to all employees at J Kitchen & Sons Pty Ltd throughout Australia, 1920s .10-.11 Blue bound copies of "Advance" - a journal of interest to all employees at J Kitchen & sons Pty Ltd throughout Australia, Volumes 1 to 7 1924 to 1931Nilbusiness and traders - soaps/candles, industry - manufacturing, workers, j kitchen & sons pty ltd

A novelty postcard that was produced by Nucolorvue Productions Pty. Ltd. as a souvenir of Marysville in Victoria.A novelty postcard that was produced by Nucolorvue Productions Pty. Ltd. as a souvenir of Marysville in Victoria.IN A BIT OF A HURRY, SO JUST WRITING/ A FEW LINES NU-COLOR-VUE/ OF/ AUSTRALIA 11 SZ041/ NCV 3703 Printed in/ Australia POST CARD Nucolorvue Productions Pty. Ltd./ Telephone: (03) 560-1788 COPYRIGHTmarysville, postcard, souvenir, nucoloruve productions

Uniform jacket, Black doublet style with silver braid around stand-up colar, fastened with 7 silver, diamond shaped, scotish thistle buttons (1 missing). Black braid around cuffs, and pocket and tail flaps. Black cord epaulettes on shoulders. 3 strieps of silver braid on sleeve cuffs, front pocket flaps (2), tail flaps (2). Silver daimond shaped, scotish thistle button on epaulettes, pocket flats, cuffs, between tail flaps (both missing). Black lining in body, white striped lining in sleeves, Padded shoulders, Label "David Lack Pty Ltd, uniform specialist Melbourne." Label "David Lack Pty Ltd, uniform specialist Melbourne." flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, uniform, uniform maker, melbourne uniform, david lack pty ltd, scottish thistle button