The Scheibe Bergfalke II is a high performance (for its day) and relatively inexpensive two seat sailplane designed by Egon Scheibe. It appeared in 1953 as a derivative of the Scheibe Mu13 Bergfalke and incorporated design changes to resolve and simplify structural issues that affected the Mu13. The Bergfalke II-55 followed in 1955. About 300 of the Bergfalke II and II-55 types were built in Germany and Sweden. This aircraft of the Bergfalke II-55 type was built by Scheibe in 1961 (work number 339). After a long life at Fliegergruppe Leimen e.V. logging 6754 flights and 1588 hours in the air, the glider was imported into Australia from Germany in June 2004. The glider was registered as VH-GKZ in January 2005 by Thomas Dattler of Millumbindy and flown only a small number of occasions (probably at Byron Soaring Centre). The Mangalore Gliding Club appears to have taken an interest in the glider in 2006 and completed routine Form 2 inspections in 2006 and 2009. The amount of usage during this period is unclear as the logbook records held are incomplete. In January 2012 the glider was purchased by the Southern Riverina Gliding Club and flown at Tocumwal until it was damaged in 2013 due to being blown over while at rest on the airfield. The 10 year survey was due in March 2013 and a decision was made by the club to donate the glider to the Australian Gliding Museum instead of completing the necessary repairs for returning it to an airworthy condition. It is estimated that the glider was flown about 300 times and perhaps logged about 140 hours in the air in Australia. If restored this exhibit will be representative of the Scheibe Bergfalke II-55 sailplane type (a rarity in Australia).Tandem two seat sailplane of a wood and tubular steel construction covered with plywood and fabric. It has a fully enclosed cockpit under perspex (which is missing from this airframe). The wings which join the fuselage at shoulder height are swept forward such that the aircraft can be flown solo from the front seat and be properly balanced. The aircraft is in a damaged condition. Registration "GKZ" on sides of fuselage glider, sailplane, australian gliding, scheibe, bergfalke, byron soaring centre, mangalore gliding club, dattler, southern riverina gliding club, tocumwal

The Salamandra is a Polish glider designed by Waclaw Czerwinski at the Military Glider Workshops in Krakow in 1936. This glider, designated “W.W.S.1”, was produced in substantial numbers prior to the second world war and used in Poland and some other eastern European countries for training pilots. Only one example survived the war, hidden away in the village of Goleszow in Silesia. In addition, no technical drawings could be found, so when the glider was discovered, the Gliding Institute being keen to re-establish gliding in Poland, used the glider to draw up new plans for construction. Five were built for the Institute in 1947 before production was resumed of the “Salamandra 48” at the SZD Jezow Workshops. Improvement were made by adding airbrakes and structural changes for the “Salamandra 49” and a windscreen and larger tailplane were changes adopted for the “Salamandra 53”. An export version designated “53A” was sold to and built under licence in China. Production of the Salamandra ceased in the early 1960s. Total production may have been in excess of 500. The glider was well regarded as a light weight trainer capable of soaring performance. The Museum’s replica was built by Ray Ash and may be may be classified as a “Salamandra 53”. However, he has added something of his own to the design by replacing the cable runs in the wings with control rods. The glider is substantially complete. The wings and tail / rudder surfaces have been covered with poly-fibre fabric. The fuselage woodwork is sealed with varnish. In addition to the finishing work (including painting) and rigging of the main components, the linkages for Ray’s control rod modification may need further engineering to make them operational. The Ray Ash Salamandra is the first of the type to appear in Australia. The Salamandra did not play any role in the development of gliding in Australia in the early years. However, it is an important exhibit in that it shows in tangible form a nacelle fuselage training glider in configuration and construction detail. As such it revisits the pioneering era of the 1930s and 1940s in Australia when wood, wire and fabric were the rule and the nacelle primary glider was generally the first step up for pilots who had mastered the basics in an open primary.Nacelled solo training glider of traditional wood and fabric construction. Construction incomplete.Noneaustralian gliding, sailplane, glider, salamandra, czerwinshi, poland, ash

The Ka 8 was designed by Rudolf Kaiser in 1957 and built by Alexander Schleicher. It has been described as the single seat version of the Ka 7 Rhonadler. The Ka 8 proved popular with clubs in its role as a sailplane for early solo flying. Over 1100 were produced. The Museum’s example is a Ka 8B which is the second variant of the design, distinguishable by a larger blown Plexiglas canopy and improved ailerons. The particular glider was built by the RAAF Williamtown Gliding Club from kit supplied by Edmund Schneider Ltd of South Australia as agent for Alexander Schleicher. It was test flown on 8 July 1967. For a period from August 1994 it was owned by a syndicate at the Bendigo Gliding Club. The last entry in the log book is dated January 1995 at which time the glider had accumulated 1148 hours from 2303 flights. From 1967 to 1994, the glider was flown at numerous places including Williamtown, Bellata, Warkworth, Dubbo, Waikerie, Quirindi, Tamworth, Redding, Narromine, Leeton and Keepit. During 1994 and 1995 it was flown a small number of times at Bendigo. A notable flight recorded in the logbook is dated 31 October 1971 when W. Kenny reached 11,000 feet in height during a flight of 5 hours 10 minutes. The last owner prior to the transfer of the glider to the Australian Gliding Museum in 2015 was John Ashford of the Geelong Gliding Club. The glider carries Serial Number 8478-SH and appears to have been registered firstly as VH-GPA and secondly as VH-GMA. The last registration (VH-GMA) was cancelled in 2011.This Kaiser Ka8B sailplane, when fully restored, will be an airworthy example of a popular 1960s German club sailplane type. It is a rarity in Australia as only 4 of the type have been registered and flown here.Single seat sailplane made with a steel tube framed fuselage and wooden wings. A glass plastic moulding has been used to form the top of the fuselage forward of the cockpit. The structure is fabric covered.The glider serial number 8478-SH and the registration VH-GMA.australian gliding, glider, sailplane, schleicher, kaiser, ka 8, schneider, raaf williamtown gliding club, bendigo gliding club, geelong gliding club, ashford

The Hall Cherokee II glider is an American design for amateur construction from plans. The designer was Stan Hall (1915-2009), a professional engineer, who gained extensive experience in the United States aviation industry during World War 2 including the programs for military gliders. He continued to work as an engineer for aircraft manufacturers and as a consultant to the industry after the war. He was active in gliding and, in particular, the home built sailplane movement. The Cherokee II was one of about 10 glider designs that he produced: it came out in 1956. It is understood that over 100 Cherokee gliders have been built. In Australia the number is possibly 10 or 11. The Hall Cherokee VH-GVO was built by R.D Meares of Caringbah, New South Wales. The glider was registered as VH-GVO on 11 October 1973 and given serial number “GFA-HB-82” by the Gliding Federation of Australia. The Logbook for VH-GVO appears to be a complete record of the flying history; in aggregate 210 hours 40 minutes in the air from 331 flights. The first test hop occurred on 29 July 1972 at Camden, New South Wales. VH-GVO was last flown on 22 July 1986. Many of the flights recorded are of one or two hours duration. The glider was last inspected and certified as airworthy and in a reasonable condition at the Hunter Valley Gliding Club in July 1986. Since that time, until transferred to the Australian Gliding Museum, the glider was in storage. Structural restoration work has been completed on the fuselage and one wing. However, inspection of the other wing revealed extensive damage to the ribs and spars and consequently a decision was taken to make it a static exhibit. The exhibit is an example of home built construction of a type that has proved popular amongst amateur glider builders.The Hall Cherokee (formerly registered as VH-GVO) is a single seat wooden home built glider. The glider is constructed from wood, plywood, fabric and metal fittings, all commercial grade except for main wing fittings, pulleys, cables and bolts. The fuselage is simple with four main longerons and bulkheads with diagonal bracing. The wing has two identical solid spars which form a geodetic structure, hence the leading edge is non-structural. Registration VH-GVO – serial number GFA-HB-82 australian gliding, glider, sailplane, hall, cherokee, meares, hunter valley gliding club

The Schreder HP 14V is an all metal single seat sailplane designed by Richard Schreder in America. The design is an evolution of Schreder’s metal sailplane designs that date from the late 1950s. Schreder won the United States National Soaring Championship in 1966 in the prototype HP 14. He marketed the glider in kit form in the 1960s and 1970s and allowed Slingsby in the UK to further develop the design for production. Schreder HP14 V, registered as VH-GGB, was built in South Australia by Harry Bache of the Waikerie Gliding Club in the 1970s. Martin Simons, an authority on vintage sailplanes (including Slingsby types), refers to this airframe as “built entirely from scratch”. After Bache, this Schreder HP14V passed on to E.G. Moore and N.L. Lovell at Ararat in Western Victoria, then Graeme Rickert of the Canberra Gliding Club and finally, to Greg O’Sullivan of the Geelong Gliding Club. The glider was first flown on 20 December 1975. It appears to have been flown regularly over its life to 2015 and the cumulative use being 1386 hours flown from 702 launches. The log book does not disclose details of flights except as aggregates of flights and times. Details of notable flights by Bache and Moore et al are not available. However, reports from Rickert and O’Sullivan indicate that a good number of cross-country flights of 300km or longer were achieved in this aircraft. A well-engineered metal sailplane from the 1970s with good soaring performance which was designed for amateur construction. All metal single seat glider sailplane with a distinctive V-tail, finished in a white and blue colour schemeRegistration letters 'GGB' on sides of fuselageaustralian gliding, glider, sailplane, schreder, slingsby, bache, waikerie gliding club, moore, lovell, rickert, o’sullivan, canberra gliding club, geelong gliding club.

Objects. Clothes brush is oval in shape, with a polished wooden base, and black bristles. Shaped to a rounded point at each end. Bristles 2.5 cm long. Nine rows of bristles. Make-up brush bears Chinese writing on the handle, 23.5 cm long with 6.5 cm long white hairs forming the brush. Hairs are held in an ebony cup shape fitting, attached to the handle. An ebony top-knot completed with a red silk ribbon loop finishes the top of the handle.Hair comb: Tortoise shell, with three 7 cm long teeth, which unfortunately are broken from the fan-shaped decorative top. The fan-shaped top of the comb, has an art-deco type flowing floral design-1920's.Chinese lettering - six characters.costume accessories, female, clothes brush, make-up brush, hair comb.

Clothing. Cream polished cotton, full length half slip petticoat. Plackett at the back, fastens with two metal hooks, and hand-stitched loops. The back features a 'crinolette', where two rows of tapes are gathered in to give volume to the back of the garment. As the crinoline started to subside at the end of the 1860's. The centre front panel features 6 angled bands of lace 4.5 cm wide and angled to form a V shape. (1) A 9.5 cm band of pleated linen gauze-like fabric, edged with a 5 cm band of linen lace. (2) A 15 cm double layered frill-top layer 2 cm wide silk like pleats, lined with linen muslin type fabric, and an under frill of polished cotton, pleated in one cm wide knife pleats. The top frill is of fine cream cotton lace. At the top edge is a 3.5 cm wide band of floral cotton lace, and adjoined at the lower edge with a 9 cm deep pleated trim of exquisite cotton "floral and swirls" lace. The top frill is 42 cm wide, and extends over the centre front panel only. A cotton covered " stiffening- possibly bamboo or whale bone, extends 31.5 cm ;long at the crinolette. An unusual 'pocket like bag' is sewn into the right side seam 14 cm below the waist. This has rounded corners, and is 8 cm wide at the top, 17.5 cm wide at the lower edge, which is then rounded slightly. Overall length of the 'pocket' is 38 cms.costume, female, crinolette full length half slip

Typed letter on paper with Hanro letterhead and dated 30 November 1932. It mentions that the new company will execute the Bank Mortgage forms over the deeds at present held by the bank. Signed by four directors. Duplicate copy written across the top corner. A Draft Minutes, dated 30 the November 1932 mentioned those present, Messrs Longstaff, Lansell, Keck and Rankin. Those authorized to signing and endorse cheques, to draw, endorse and accept Bills of Exchange and Drafts and to make and endorse Promissory Notes on the Company's behalf in connection with the E S & A Bank. The second part refers to transfer of assets. The third,dated 29 November 1932 is the Resolution to be Taken.hanro, clothing, share register, hanro collection - letters - authority to sign cheques, the english scottish & australian bank ltd, harry francis longstaff, george victor lansell, herbert keck, ronald alexander rankin, william bowman hanna neill, ernest frederick granger, phillip henry mckean

Typed page outlining the history of the Long Gully Fire Brigade. A meeting was called on the 28/5/1873 for the purpose of forming a fire brigade. Mr J Grenfell was elected Captain and Mr J Neal Lieutenant. The brigade was closed down on 30/6/1932.bendigo, history, long gully history group, the long gully history group - long gully fire brigade, long gully mechanics institute, mr j grenfell, mr j neal, sandhurst city brigade, st matthews church, american gully, easter fair, buffalo lodge hall, rose of australia hotel, bendigo council, g a ellis

Narrow fox fur collar. Pointed 1 cm wide 'skin' nose, which forms the upper part of the enclosed metal clip fasten the collar (squeeze lever on inside). Two glass eyes. A corded ''chain'' finished with a woven toggle, and a cord covered hook fasten the fur around the neckline or shoulders. Ruched ribbon trims both ends of the crepe type cotton(?) lining '' tail'' has fur threaded onto a linen thread.costume accessories, female, red fox fur collar

(a) Small form with details of ' Bendigo ' Thompson written on it. (b) Photocopy of newspaper articles relating to William Thompson 'Bendigo' the prize fighter. (c) Photocopy of an article relating to the life of William Thompson, who died 23/08/1880 and contains two photos - 1 of Bendigo and secondly his grave. (d) two copies of a typed letter sent by Eric N. Turner, 45 Brighton St., Nottingham, dated 18/09/1962. It relates to the life of William Thompson, known in the ring as Bendigo. (e) Newspaper article titled 'Was Bendigo called Castleton' dated 9/06/1960. In 1853 the Government gazette has an entry that Castleton was changed to Sandhurst. (f) A small newspaper article titled Abednigo named Bendigoperson, individual, bendigo thompson, william thompson, bendigo thompson, abednigo, castleton, naming of bendigo

Slide. Bendigo Views. View of an agave type plant. The leaves are in a rosette form and the leaves have sharp serrations along the edges.slide, bendigo, bendigo views, bendigo views

The Education Department Victoria supplied forms and other stationery to schools and this folder contains many examples dating from the 1920s to 1960s. Examples are letterhead and envelopes, staff vacancy forms, fee register sheets, etc.A wide variety of examples is contained in this folder. Forms such as these would normally survive with writing on them. These are unused and in good condition.Forms, letterhead, etc. supplied by Education Department. With examples of each form. [Not dated Range from 1920-]. Collected in brown hard cover folder with string binding. Typed list of contents on first page. Handwritten on cover: "Materials"collingwood technical school, cts, forms, stationery, education department victoria, nmit,

This type of pessary was often used for uterine malpositions and displacements and usually made from vulcanite. This particular object is known as Hodges moulded pessary. [Source: George Tiemann & Co Surgical Instruments catalogue.1989. page 486.] The pessary was originally regarded as an instrument and made from cork, ivory, hard rubber or gum-elastic. In later times, they were made from black vulcanite, flexible tin, soft copper wire covered with Indian rubber, and celluloid. The form of the pessary was and still is variable -either round, oval, or moulded in some cases combining three or four curves depending on the size of the pessary. In ancient times, medicated pessaries were made from emollient. astringent and aperient. Several of these are still used, but in more modem times are called vaginal suppositories. Anal suppositories are still used to suppress the pain of haemorrhoids. Moulded black vulcanite pessary. Pessary is irregular in shape, and medium size. "I.T.A.Y." inscribed on upper curve.pessary, intrauterine device

This type of pessary was often used for uterine malpositions and displacements and usually made from vulcanite. This particular object is known as Hodges moulded pessary. [Source: George Tiemann & Co Surgical Instruments catalogue.1989. page 486.] The pessary was originally regarded as an instrument and made from cork, ivory, hard rubber or gum-elastic. In later times, they were made from black vulcanite, flexible tin, soft copper wire covered with Indian rubber, and celluloid. The form of the pessary was and still is variable -either round, oval, or moulded in some cases combining three or four curves depending on the size of the pessary. In ancient times, medicated pessaries were made from emollient. astringent and aperient. Several of these are still used, but in more modem times are called vaginal suppositories. Anal suppositories are still used to suppress the pain of haemorrhoids.Moulded black vulcanite pessary. Pessary is irregular in shape, and large size.pessary, intrauterine device

This type of pessary was often used for uterine malpositions and displacements and usually made from vulcanite. This particular object is known as Hodges moulded pessary. [Source: George Tiemann & Co Surgical Instruments catalogue.1989. page 486.] The pessary was originally regarded as an instrument and made from cork, ivory, hard rubber or gum-elastic. In later times, they were made from black vulcanite, flexible tin, soft copper wire covered with Indian rubber, and celluloid. The form of the pessary was and still is variable -either round, oval, or moulded in some cases combining three or four curves depending on the size of the pessary. In ancient times, medicated pessaries were made from emollient. astringent and aperient. Several of these are still used, but in more modem times are called vaginal suppositories. Anal suppositories are still used to suppress the pain of haemorrhoids.Moulded black vulcanite pessary. Pessary is irregular in shape.intrauterine device

Thomas’ Retroflexion Pessary is narrower in proportion to its length, while the greater bow is enlarged to a bulb-like form. It enjoyed great popularity and as such was manufactured in a great variety of sizes. Comprised of hard rubber because of its lightness and the high polish that may be given it. The shape can be adjusted by covering the device in petrolatum and heating it with a spirit lamp or immersing it in boiling water. Manufactured in three sizes, and could be combined with a cup and stem external support. See Allen & Hanburys Gynaecological instruments catalogue, page 707.Two moulded black pessaries, Thomas retroflexion type. Made of black vulcanite. Narrower at one end.pessary, intrauterine device

This type of pessary was used in the treatment of retroflexion of the uterus. Thomas’ Retroflexion Pessary is narrower in proportion to its length, while the greater bow is enlarged to a bulb-like form. It enjoyed great popularity and as such was manufactured in a great variety of sizes. Comprised of hard rubber because of its lightness and the high polish that may be given it. The shape can be adjusted by covering the device in petrolatum and heating it with a spirit lamp or immersing it in boiling water. Manufactured in three sizes, and could be combined with a cup and stem external support. See Allen & Hanburys Gynaecological instruments catalogue, page 707.Vulcanite pessary. Pessary is loosely horseshoe shaped, tapering to a point at the proximal end. The curve of the pessary at the distal end thickens and is rounded. Majority of the pessary is concave.intrauterine device, pessary

Access to a pre-school education is an important to childhood development and Princess Elizabeth Kindergarten provided this to children who were hard of hearing. These documents form an insight into the development of the Princess Elizabeth Kindergarten. Plain A4 cardboard with tape spine encloses documents up to foolscap in size relating to the Princess Elizabeth Kindergarten for the Deaf (PEKD). Includes general correspondence from the Education Department from 1957 to 1971, the Education Department taking over responsibility for teaching staff at PEKD in 1957, having assumed reponsibility for the education of students at the VDDI. There are documents relating to the meetings of the PEKD sub-committee from 1969-1972, documents relating to the building extensions 1972-1973. On spine, typed: "1957 / 1971/EDUCATION DEPARTMENT/1969 / 1972 P.E.K.D. Sub-Committee/1972 / 1973 P.E.K.D. BUILDING EXTENSIONS/1972 P.E.K.D. EXTENSIONS deaf children australia, dca, princess elizabeth kindergarten, pekd

Carnival (Dutch: Carnaval) is an important annual event heralding Lent in the southern provinces of The Netherlands, with each village often having its own "Carnavalsclub" and traditions. Many Dutch immigrantsg from the southern provinces have continued this tradition and formed their regional Carnavals Clubs in Australia. Each club has its own colourful uniforms, including specific hats. There are potentially three types of hats: A formal hat for official events, a work hat for use during normal club nights and for those members lucky enough to be chosen for a year as the "Prince" of the club, a Prince's Hat. Dutch Carnival is primarily a festival celebrating human folly which is why the hats are like jesters' caps. "Carnaval" comes with a rich tradition of ridiculing people and institutions of authority, and so, for instance, the "Prince" is saluted with military salutes which are performed the wrong way round, to the great merriment of onlookers. Special songs celebrating the foolishness of people in high places, such as politicians, are composed each year for "Carnaval". For people from the southern provinces of the Netherlands, the annual "Carnaval" is an important cultural event.Decorative hat from silk-like material, coloured orange, green and cream and finished off with silvery gold band and other decorative items (see picture - also see items 6352 and 6353).Has the name "L. Havel" on the inside.carnival hat; brabant; limburg; dutch migration

Carnaval is an important annual event in the Southern Provinces of The Netherlands, with each village often having its own Carnavals Club and traditions. The Dutch People coming from the Southern Provinces continued in many cases this tradition and formed their regional Carnavals Clubs in Australia. Each Carnalvals Club has its own colourful uniforms, including a hat. There are potentially three types of hats: A Formal Hat for official events, a Work Hat for use during normal club nights and for those members lucky enough to be for a year chosen as the "Prince" of the club, a Prince Hat.For people from the Southern Provinces of the Netherlands, Carnavall is an important cultural event.Decorative hat from silky type silver, gold, blue and aqua material, finished of with bells at front of hat (see picture - also see items 6351 and 6352).has a 6 on the insideprince carnaval limburg brabant dutch migration

Before mechanisation, pills were rolled by hand using equipment such as this pill press. Powders ingredients were blended together to form a resin, rolled and laid across the width of the platform. The paddle was then used to push the "sausage" shape through the grooves, creating a small, consistently sized and shaped, pill. The pill was then allowed to dry for later sale. This pill press is of uncertain origins but is representative of the type of equipment used to create pills in the 19th Century. It has the capacity to make 24 pills at once, and markings on the metal plate indicate each pill would have been the equivalent of "5 grains" (approx 0.3 grams).Rectangular wooden platform with a metal (brass) plate divided into 24 (twenty-four) grooves with a catchment area. The wooden paddle has two handles, one on each end, with a matching metal plate and grooves, as well as metal (brass) guide bars to help the paddle align with the platform.Handwritten on base of platform in black ink over white background: C11087 Handwritten on inside of guide bar on paddle in black ink over white background: C11087 Manufacturer's detail stamped into metal groove on platform: S. MAW SON / & / THOMPSON / LONDONpill press, pharmaceuticals, apothecary, pharmacy

Heywood Waterworks Trust was constituted on 20 November 1962 upon application by Councillors of the Shire of Portland to construct, manage and maintain the works for the supply of water to the township of Heywood. The Trust was abolished on 1 July 1984 under the Water and Sewerage (Restructuring) Act 1983 when it amalgamated with the Heywood Sewerage Authority to form Heywood Water BoardA cast iron seal press, . This was used by Heywood Waterworks Trust to emboss agreements and official documents. Die is still attached to the press. It reads: Heywood Waterworks Trust 1963Small metal machine painted black and mounted onto a black rubber base. Two dies are attached with the seal of Heywood Waterworks Trust. Paper is placed between the dies, the handle depressed and the seal embossed on the paper under pressure as a blind (inkless) embossing. The seal consists of two circles with the wording "Heywood Waterworks Trust".Heywood Waterworks Trust 1963/ Excello / Reg Trade Mark/ Seal Press/ Pat NO 420419/Size No 2/Inscription on rubber base: "EXCELLO SEAL PRESS" / REGD TRADE MARK / 1. PATENT ROLLER BEARING HANDLE PAT. NO. 420419 / 2. DURABLE PLASTIC COUNTER / 3. RUBBER DESK PROTECTOR / STANDARD RUBBER TYPE CO. LTD. / TOKYO JAPAN"heywood, public administration, water supply, amalgamations

This book provides a thorough overview of the educational aims of all kinds of museums and galleries. it includes a discussion of different types of museums, their educational structures and arrangements, all of which vary enormously. Different forms of education provision are examined in relation to various types of both collection and audience. Taking into consideration the increased emphasis, at both local and governmental levels, on public service and customer care, Hooper=Greenhill discussed, and makes practical suggestions for the way forward to museums.museums -- educational aspects, museums -- administration

Directions for the knitting of standard socks for men in active service during WWI. Issued by the Lady Mayoress's League, Melbourne, in September 1915. The Lady Mayoress's League, or Lady Mayoress's Patriotic League, was formed on 7th August 1914 by Lady Hennessy, Lady Mayoress of the City of Melbourne. The League was formed to supplement the official supplies issued to each soldier by providing 'comforts' such as socks and food packages, and by 1915 was the recognised agent in Victoria for the reception and despatch of all gifts other than those sent privately. In September 1916 it became part of the Australian Comforts Funds, an Australia-wide umbrella organisation formed from individual state-based organisations of this type. Folded single sheet of white paper that has discoloured with age, printed in black on both sidesthe lady mayoress's league, wwi fund-raising

Invitation in the form of a typed letter from the General Secretary of the Melbourne Swimming Club,, L M (Les) Phillips to attend a picture night at Leonards Cafe Baths on Monday 29 August. The films shown included films of the 1948 London Olympics and other films of swimming and general interest. The year of the event is unspecified. It could have been 1949 or 1955. The Club was established in 1894 and is not the same as the present day competitive swimming club of that name. Quarto sized page of buff coloured paper, typed and written in black on one sideHandwritten correction of typed venue of event, changed from Gymnasium Richmond to "Leonards Cafe" St Kildamelbourne swimming club

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 92NQR - Goods Vehicle - Open Medium Truck NQ/NQR OPEN MEDIUM TRUCKS. 218 of these goods vehicles were built between 1898 and 1914 numbered 1-218. Originally, these wagons carried the code letter R as they were built with sides and ends. Some later had the R removed if they regularly ran as flat wagons without theh sides and ends. Over the years, a number of NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames. 92 NQR VR Service History : *NQR 92.VA - 2/ 3/1907 NWS Built new - / /1926 - To NQ 92.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck with drop ends Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 92NQR - Open Medium Truck with drop ends made of Steel and metal92NQR puffing billy railway, pbr, rolling stock , 29 nqr, narrow gauge rolling stock, victorian railways, nqr wagon

3 NAL - Teepookana - (Mt. Lyell) O 3; 3 NBL - 1st. class saloon car (20) NAL FIRST-CLASS SALOON CAR. Four saloon end-platform cars originally built during 1901–1902 by the Lancaster Railway Carriage and Wagon Company Ltd. for the 3'6" gauge Mt. Lyell Mining & Railway Company in Tasmania and classed O. Converted for use as second-class cars on the 2'6" gauge Puffing Billy Railway during 1965–1966, these cars were reclassified NBL and numbered 1–4. The L recognises their Mt. Lyell origin, No. 1 was kept for use as the Railway's VIP car and was reconditioned to a higher standard. No. 2 was similarly upgraded in 1985 for use on special occasions. In 1989 No. 3 was similarly reconditioned with No. 4 receiving similar treatment in 1995. These cars were re-classified NAL in recognition of their new first-class nature. The Mt Lyell Railway was closed in 1963 and subsequently dismantled, but fortunately several of the locomotives and carriages passed into preservation. Purchased by Puffing Billy Preservation Society from the Mount Lyell Mining & Railway Company in the 1960s, it was converted to 2' 6" gauge. It has since given many years of service on the Puffing Billy Railway. TASMANIAN CARRIAGES & GUARDS VANS No. Builder Type Year built Ex. Location Note NAL 1 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Mt Lyell NAL 2 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Rinadeena NAL 3 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Teepookana NAL 4 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Dubbil Barril Lancaster Railway Carriage and Wagon Co The Lancaster Company was formed in 1863 and owned extensive works on the outskirts of Lancaster where it produced railway rolling stock of all descriptions, tram cars, wheels and axles, etc and had a reputation for work of a very high-class character. In 1902 Metropolitan Amalgamated Railway Carriage and Wagon Co was registered on 18 April and incorporated as a limited company to amalgamate 6 companies including Lancaster Railway Carriage and Wagon Co These works were closed in 1908 when the business was transferred to Ashbury 1st Saloon Carriage Owner Mount Lyell Mining and Railway Company, Queenstown, TAS Builder Lancaster Railway Carriage and Wagon Company Ltd, England Build date 1901 - 1902 Car length 31 ft 4 in (9.55 m) Car weight 11 t (11.18 ton) Gauge Original Narrow: 1,067 mm (3 ft 6 in) Rebuilt Narrow: 762 mm (2 ft 6 in) Configuration Bogie Capacity 1 -3: 20 Passengers 4: 28 Passengers Number in class 4 Numbers Mt. Lyell: O 2 - O 3, O 5, O 6 Puffing Billy: NBL 1 - NBL 4, NAL 1 - NAL 4, Mt. Lyell, Teepookana, Rinadeena, Dubbil Barril First run 1901 No. Name Location In Service Withdrawn Condition Livery NAL 1 Mt Lyell, NBL 1 Puffing Billy Reclassed from O 5. Recoded to NAL 1. Operational NAL 2 Teepookana, NBL 2 Puffing Billy Converted from O 2. Upgraded - 1985. Recoded to NAL 2. Operational NAL 3 Rinadeena, NBL 3 Puffing Billy Converted from O 3. Upgraded - 1989. Converted to NAL 3. Operational NAL 4 Dubbil Barril, NBL 4 Puffing Billy Converted from O 6. Upgraded - 1995. Converted to NAL 4. Operational Historic - Industrial Narrow Gauge railway - Mt. Lyell Mining & Railway Company in Tasmania - 1st Class Saloon Carriage1st. class saloon car made of Timber and steel3 NAL - Teepookanapuffing billy railway

4 NAL - Dubbil Barril - (Mt. Lyell) O 6; 4 NBL - 1st. class saloon car (28) NAL FIRST-CLASS SALOON CAR. Four saloon end-platform cars originally built during 1901–1902 by the Lancaster Railway Carriage and Wagon Company Ltd. for the 3'6" gauge Mt. Lyell Mining & Railway Company in Tasmania and classed O. Converted for use as second-class cars on the 2'6" gauge Puffing Billy Railway during 1965–1966, these cars were reclassified NBL and numbered 1–4. The L recognises their Mt. Lyell origin, No. 1 was kept for use as the Railway's VIP car and was reconditioned to a higher standard. No. 2 was similarly upgraded in 1985 for use on special occasions. In 1989 No. 3 was similarly reconditioned with No. 4 receiving similar treatment in 1995. These cars were re-classified NAL in recognition of their new first-class nature. The Mt Lyell Railway was closed in 1963 and subsequently dismantled, but fortunately several of the locomotives and carriages passed into preservation. Purchased by the Puffing Billy Presevation Society from the Mount Lyell Mining & Railway Company in the 1960s and converted to 2' 6" gauge. It has since given many years of service on the Puffing Billy Railway. TASMANIAN CARRIAGES & GUARDS VANS No. Builder Type Year built Ex. Location Note NAL 1 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Mt Lyell NAL 2 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Rinadeena NAL 3 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Teepookana NAL 4 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Dubbil Barril Lancaster Railway Carriage and Wagon Co The Lancaster Company was formed in 1863 and owned extensive works on the outskirts of Lancaster where it produced railway rolling stock of all descriptions, tram cars, wheels and axles, etc and had a reputation for work of a very high-class character. In 1902 Metropolitan Amalgamated Railway Carriage and Wagon Co was registered on 18 April and incorporated as a limited company to amalgamate 6 companies including Lancaster Railway Carriage and Wagon Co These works were closed in 1908 when the business was transferred to Ashbury.Historic - Industrial Narrow Gauge railway - Mt. Lyell Mining & Railway Company in Tasmania - 1st Class Saloon Carriage1st. class saloon car made of Timber and steel4 NAL - Dubbil Barrilpuffing billy railway, narrow gauge