The extent of exterior changes veered not much further than a redesigned Holden logo and wheel trims. An updated Ecotec (Emissions and Consumption Optimisation through TEChnology) version of the Buick V6 engine coincided with the changes to the engine in the United States. The Ecotec engine packed 13 percent more power, an increase of 17 kilowatts (23 hp) over the VR, cut fuel consumption by 5 percent, and increased the compression ratio from 9.0:1 to 9.4:1. Holden mated the new engine with a modified version of the GM 4L60-E automatic transmission, bringing improved throttle response and smoother changes between gearsThe VS Commodore was the last of which to be sold as Toyota Lexcens, as Holden and Toyota ended their model-sharing scheme The last Lexcens were built during 1997This model was also sold between 1995 and 1997 in small numbers to Malaysia and Singapore as the Opel Calais.4 door sedan VS Commodore sedanLion and stone badge on Bonnet and on Boot centre, Commore on both mudguards Holden badge on Rear under tail lightsvehicle, vs commodore, car

A small number of heavy cast iron weights and two rods remain at the Point Hicks Lightstation. These weights comprise one rod with a forked top and four circular weights attached to the bottom of the shaft. The weights and rods were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. They were attached to a cable or chains and moved vertically in similar fashion to the way weights move on grandfather clocks. As the weight fell, the optic clock was driven and the lens was turned. To keep the clock turning, the weight needed to be wound back up to the top of its travel. The cables and weights in this lighthouse were visible as they moved through the length of the tower up to the lantern room. It was usual for systems to move inside a tube extending up to the top, but in this case the tower’s cast iron spiral staircase, which is supported on cantilever cast iron brackets set into the concrete wall, spiralled around the space in which they moved. Lighthouse keepers had the arduous job of having to constantly wind the clock to keep the light active, and at least two keepers needed to observe a strict roster of hours. When electric motors were invented, all of this became redundant and the motors were able to turn the optic for as long as there was power to drive them. In December 1964, the original 1890 Chance Bros kerosene‐fuelled light and clockwork mechanism were replaced by small electric motor, and the number of keepers reduced to two. The six circular weights and rods originate from the obsolete system and may have been part of a larger set. Wilsons Promontory retains seven of its original set of ten weights, all of which are detached from the tower’s weight tube. Cape Schanck has a set of fourteen weights remaining in situ as well as another four detached weights, which have inscriptions. One weight is displayed in the lantern room at Cape Otway. The image shows four of the clockwork weights attached to a rod with a forked top. They were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. The Aldis lamp in its case sits on the floor next to the weights. Source: Parks Victoria.The Point Hicks weights have first level contributory significance for the insights they provide into the superseded technology and operations of a late nineteenth century lighthouse. They are well provenanced and are significant for their historic value as part of the lightstation’s Chance Brothers optical system installed in 1890. Four circular metal weights are stored on a metal rod with a forked section at the top. The weights have a cut out section which allows the weights to be removed easily.

Story to be placed here - Available to publicMinature cast iron, Black Solid Wood Stove with miniature utensils. The stove is on legs with left hand extension for pots, right hand extension with holes, removeable hot plates [4 round 1 rectangle] tin chimney with folded join and seperate decorative cover with pot stands x2 , front door opens on hinges with internal gold pan with gold crescent logo. Frying pan, hot plate handle and "swan flat iron on stand. Solid fuel space with tin base. 2 screws and bolts used to assemble stove. 14 removeable parts.crescent, star, scrolls, wood, iron, tin, cast, stove, black, cast iron, star, solid, fuel, chimney, flat iron stand, flat, stand, hot plates, frying, pan, bolt, screws, legs, toy, miniature, crescent, made in taiwan, taiwan, wood box

Newspaper clipping from The Sun (?), undated, late 1970? about Parliament (Victorian) being told by the Minister for Fuel and Power (Mr. Balfour) that the City of Ballarat wanted to scrap its trams, following a question from Mr. Trezise (ALP Geelong North) in the Legislative Assembly. No decision had yet been made. Also quotes the Secretary of the Ballarat Trades and Labor Council, Mr. A.C. Williams saying that Ballarat people would protest this decision. On rear of cutting has an item about the Noongah Enquiry, an inquiry into the sinking of the Noongah. Appears to be from a Melbourne Paper, different typeface to that of the Courier.trams, tramways, closure, parliament, ballarat

a. Hard cover book green cover, red spine. Written on front 'South Deborah Gold Mines No Liability Journal' Contained handwritten journal entries for years 1941 to 1952 Inserted loose pages (2) with handwritten profit and loss account 1952. Contains entries relating to expenditure in mine including timber, printing, stores, air, mine charges, fuel, lighting, cartage, crushing charges. Salaries to Gl Kingsley, W. Edwards, and wages for workers. b. Two-page typed summary of information contained in journal, prepared by Phyllis Toy (approx. 2015).business, mining, south deborah gold mines

.1 - Manual - 116 pages centred stapled - titled "MAN Buses - Driver's Handbook". Has a table of contents, item reference list and electric circuit diagrams. Covers the operation, equipment, driving, cold weather operation, maintenance, lubrication, fuels, general car and maintenance. .2 - newspaper clipping from The Age ""Gearbox flaw cripples bus fleet", dated 26/3/1987, by Tony Harrington, Transport Reporter reporting on the withdrawal of 20 buses from North Fitzroy - replacement parts no longer being manufactured. Also has a loose note about the radiator capacity.trams, tramways, buses, maintenance, man, manual, gears

The Warrnambool Co-operative had its beginnings as the Allansford Artificial Breeders Co-operative in the 1960's. In the 1970s they opened a retail store in Timor Street which had a strong rural and farming base which gradually expanded to become the largest trading department store in the district. By the late 1990's they had 8000 members and employed 84 full time and 120 casual staff. It met a sorry end in the 2000's.This plaque commemorates the opening of the Rural store which consolidated the large rural aspect of the business. It opened up the site from Merri Street at the back of the Timor Street building trading in all agricultural products, , chemicals and fuels.A link to one of Warrnambool's largest stores of the latter part of the 20th century and as such it has historical and social significance. Rectangular brass plaque with stamped black text with eight screws around the edge attaching it to a piece of heavy particle board , painted black.Warrnambool Co-Op rural Store officially opened by the Mayor of Warrnambool Cr. Gerald Shanley on Wednesday, 8th October 1997.warrnambool co-operative society limited, warrnambool co-operative rural store, warrnambool

A photo of two young ladies with metal Legacy Appeal tins and a badge tray. The slogan says "We ask so little for those who gave so much. Legacy cares for families of deceased ex-servicemen". Promoting badge day in September 1986. See also 00435. The yellow label with 00435 says that the young ladies are: "Su Davies and Carol Shaw / Staff members sold badges in the city on Badge Day, 1986". They may have been professionally taken to publicise Legacy Week in the newspapers. Carol Shaw was a staff member who participated in several events to publicise Legacy. Such as abseiling down the Gas and Fuel Buildings.A record of fundraising in 1986.Black and white photo of two young ladies collecting for the Legacy Appeal.fundraising, legacy appeal, badge week

Ash Wednesday Veteran This Bedford M Series tanker spent its working days at the Forests Commission depot at Gembrook, and among its many forays, fought the deadly Ash Wednesday bushfires at nearby Upper Beaconsfield and Cockatoo on 16 February 1983. Earlier in 1975, the M Series tankers underwent a design change at the Altona North workshops, replacing the cylindrical water tank with a “V” bottom 4090 litre water tank that sat low between the chassis rails to reduce its centre of gravity. Aluminium heat shields were also added to protect the pump operators on the back. While generally considered "bulletproof" the petrol fuel lines on this particular model were very prone to vaporise in the heat causing the motor to stall, often at the most dangerous moment.... in this case frightening the hell out of its driver, affable knockabout bloke, and firefighting legend Lex Wade. Some jokingly said this design quirk was an inbuilt safety feature to stop crews getting too close to the fire in the first place. The Gembrook tanker was later sent into the workshop and all its brake and fuel lines fitted with heat resistant lagging. Fortunately, this remarkable bushfire survivor was rescued from the scrap heap by Lex and fire equipment wizard Barry Marsden upon its retirement from a loyal and lengthy service. After a lick of fresh paint and most of its battle scars "buffed out", this time-honoured veteran now takes pride of place at the Altona North workshop.Bedford M series fire tankerMZF 347fire pump, fire tanker, forests commission victoria (fcv)

Bradley and Hubbard established their company in 1852 in Meriden, Connecticut when Nathaniel and William Bradley, Orson and Chitten Hatch, and Walter Hubbard, formed Bradley, Hatch & Company. This incarnation of the company only manufactured clocks. The Hatch brothers sold their interest in the company in 1854 and it was renamed, Bradley & Hubbard. Clocks remained the firm's primary product into the 1860s. In addition to their line of clocks, Bradley & Hubbard also produced a wide range of household items including match safes, call bells, andirons, urns, bookends, frames, desk accessories and vases. Technological advances in drilling and refining crude oil in the late 1850s and early 1860s paved the way for the demise of whale oil as lamp fuel. Soon after Colonel Edwin Drake struck oil in Titusville, Pennsylvania on August 27, 1859, Nathaniel Bradley saw an opportunity to capitalize on the future of this new fuel. Nathaniel decided to produce an extensive line of kerosene burning lamps this proved to be a wise business decision. Kerosene was soon to become a widely used, safe and relatively inexpensive lamp fuel. Between April 7, 1868, and December 23, 1913, the company was listed as the assignee for at least 89 lighting patents. Many of these patents were for lamp and chandelier designs and various improvements in lamp burners. In 1875 the company reorganized to form the Bradley and Hubbard Manufacturing Company. Walter Hubbard served as President and Nathaniel Bradley as Treasurer. The firm enjoyed rapid growth throughout the 1880s. By 1888, the company employed over one thousand workers and had showrooms in major cities including New York, Philadelphia, Boston and Chicago. One of the most prolific of the B&H products was the Rayo lamp it produced under contract for Standard Oil. In keeping with the changing times, Bradley & Hubbard produced a variety of electric lamps as well. Walter Hubbard passed away in 1911 and Nathaniel Bradley in 1915. The company continued through the 1930s and was purchased by the Charles Parker Company, also of Meriden, Connecticut, in 1940. The Parker Company was quite diversified in its product line, also producing an extensive line of lamps and high-end chandeliers. Parker operated its acquisition as the "Bradley & Hubbard Division." Parker ceased production of the Rayo lamp in the early 1950s. In 1973, the Bradley and Hubbard buildings were demolished, effectively ending that chapter in American lighting manufacture.Early innovation in kerosene lamp burner design by Bradley and Hubbard lamp manufacturers who at the turn of the 20th century were the biggest lamp producers in the world. The item is significant due to its historic connection with a major innovator of lamp design.Lamp Burner, metal container with turning screw for wick and mesh walls. Is made in 2 parts. Raised embossing on wick adjustment screw " PAT APPLIED FOR" on top of burner "B & H Patented.July.1.90.Nov.20.94"flagstaff hill, warrnambool, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bradley & hubbard manufacturing company, kerosene lamp burner, early lighting

Document regarding the abandonment of tramways in Ballarat and Bendigo. Presented to State Parliament Sept. 1970 by the MInister for Fuel and Power, the Hon J C M Balfour MLA. Outlines the losses incurred by the SEC, replacement public transport system, the worn out nature of the system, the gifting of one Bendigo tramcar to the AETM, costs of track repairs and new trramcars, tenders for replacement bus services, retrenchment payments to staff, reconstruction of existing roads following removal of the tracks, and town planning and traffic aspects. Includes a photo of a bus and interior seating. A graph from 1934 to 1970 shows the service miles, passengers carried, average fare, expenditure, revenue and loss, along with dates of major fare revisions.Yields information about the 1970 proposal to close Ballarat and Bendigo tramway systems which was successful despite previous attempts when the Bolte Governments did not have the numbers in the upper house.Document 16 Quarto sheets, duplicated and one sheet with a folded colour graph.In ink on front sheet "D/T/S"tramways, ballarat, bendigo, abandonment, closure, parliament

See InscriptionFramed B&W photo of 7 patrol cars with crews at Aleppo Railway Station, Syria. Two motor cycles are in shotAWM logo. Caption: WW1 1st Australian Light Car Patrol. Operated in the Middle East and Palestine. The seven cars (Model "T" Fords) comprised four fighting vehicles equipped with Lewis machine guns. Each had a tender vehicle to carry spares, water, fuel, ammunition etc. It was here at Aleppo Railway Station where the final battle took place to end the war. The unit was commanded by Cap't Ernest H James MC & Barww1 1st australian light car patrol, 7 ford model t vehicles fitted with lewis machine guns

Bound Accounts Book. First pages are headed ''Accounts for Payment as per Vouchers. Various Bendigo Businesses listed on each page. Pages list dates of entry from August 11, 1958 to January 5th 1970 with details of amount beside name or business. These are Bendigo businesses generally so this indicates a local operation - on the back page (page 141) is a stamp ''Gas & Fuel Corp. Of Vic. - Internal Audit'' with signature indicating start of a new book. Printed page pinned to page 15 of this accounts book gives no further information as to name of business - so potentially G&F?? First page only scanned.business, retail, gas and fuel

Firefighting often requires walking through the rough bush with handtools to construct control likens. This carry pack was designed in-house to enable the safe transport of a small chainsaw See FIRE EQUIPMENT NOTE - 35 [ https://drive.google.com/file/d/1CKtcH-3rUlrtbE9dkNP27PYT2-raVVhF/view ] A fibreglass-moulded backpack to enable chainsaw operators to safely carry saws in rough or steep terrain. Weighing just 3 kg the backpack is fitted with a padded shoulder harness, waist strap and includes two 1lt Sig Bottles for storage of a small quantity of fuel and oil. A separate storage compartment is also provided for accessories such as spare chain, sharpener and tool kit. Stihl 034 and 038 size chainsaws will fit into the backpack quite comfortably.Fibreglass carry pack for small chainsawCFLforests commission victoria (fcv), bushfire, hand tools

Demonstrates the methodology of the abandonment of the SEC systems in Ballarat and Bendigo by the SEC and the process that had to be undertaken..1 - Letter - 2 page quarto duplicated - dated 10/9/1970 addressed to the Minister for Fuelled and Power J. Balfour, signed by the SEC Secretary F. Chipperfield, submitting a notice of abandonment in accordance with the SECV Act, with reference to the TRB Enquiry of 1968, the need to lay the motion on the houses of Parliament for 24 days. .2 - Statement - 25 pages duplicated titled "SECV - Statement regarding proposal to Abandon tramways in City of Ballarat and Borough of Sebastopol and City of Bendigo and Borough of Eaglehawk", giving details of the tramways to be abandoned, history, reasons, financial, SEC Obligations following abandonment, future of Tramway's Employees, road reconstruction and future (disposal) of tramway assets."D1775" in ink on top sheet right hand corner.trams, tramways, sec, closure, ballarat, bendigo, parliament, notices and information, borough of sebastopol, borough of eaglehawk, city of ballaarat, city of bendigo

Lancelot Herbert came to Orbost in 1886, taking up a partnership with local store-owner George Temple. After Mr Temple’s death in 1891, Lancelot took over the store and progressively developed Herberts Snowy River Stores which grew into a department store of several shops along Nicholson St. He also had small shops at Cann River, Noorinbee and Genoa which were run by members of his family, as well as a carrying business and fuel outlets. Lancelot died on 2/6/1911 and his wife Martha [died 1945] are buried in a joint grave in Orbost Cemetery. (info. Noreen and Lindsay Thomson) Robert Pullar Cameron was a Shire Councillor for many years. He married Penuel Hossack and had a family of James, Flora, Penuel and Alex.This item is associated with a well-known Orbost business which started in 1888 and finally closed in c.1970. it is an example of book-keeping in the early 20th century and is a useful research tool.A white paper account with black print and red lines. Hand-written from Lancelot Herbert of Snowy River Stores to R.P. Cameron.herbert-lancelot snowy-river-stores cameron-robert-pullar

This is a small souvenir or promotional book for Herbert Stores in Orbost and Cann River. Lancelot Herbert came to Orbost in 1886, taking up a partnership with local store-owner George Temple. After Mr Temple’s death in 1891, Lancelot took over the store and progressively developed Herberts Snowy River Stores which grew into a department store of several shops along Nicholson St. He also had small shops at Cann River, Noorinbee and Genoa which were run by members of his family, as well as a carrying business and fuel outlets. Lancelot died on 2/6/1911 and his wife Martha [died 1945] are buried in a joint grave in Orbost Cemetery. (info. Noreen and Lindsay Thomson. More from "In Times Gone By' by Deborah Hall)Associated with a well-known Orbost business which started in 1888 and finally closed in c.1970. A small book with a white/cream cover and black printing. It has three cardboard pages inside which are blank. A pencil holder is attached to the back cover. On front cover: SNOWY RIVER STORES AND BAKERY. Established 1886, AND CANN RIVER. Lancelot Herbert, Wholesale and Retail DRAPER, OUTFITTER, Grocer & Ironmonger, MILLINERY A SPECIALTY. BAKERY, SMALLGOODS FRESH DAILY. Tobacco & Cigars of the Best Brands. AGENT FOR: Age, Leader, Every Saturday, Argus, Australasian, Melbourne Punch, and Sydney Morning Bulletin. WINES AND SPIRITS.souvenir herbert-stores

Booklet - for the Greyhound Racing event to raise funds for Sylvia Mitchell, held at Broadway Park on 15/7/1944. Has a photo of Sylvia on the front cover. Gives the programme for the 9 race event. Has a number of advertisements throughout, including Rowlands Table Waters on the back cover. Has pencil marks, including names of dogs for the final event. Advertisers are: G H Hauser Fruit and Vegetables, A F Witham auctioneer, Bucks Head Hotel, Gear's Pharmacies, George Hotel, Haymes Paints, Gold Top Taxis, Keith's Fruit store, Harry Davies, F M Thieseen business agents, The Regent Theatre, A H Joiner furniture, F C Heath fuel merchant, City Hall Pharmacy, Quayle cycles, Clarke's Cough mixture, and Bill Valpied Fruiter.Demonstrates work to support the Red Cross Prisoner of War fund raising.Sixteen page booklet, printed centre stapled with a red ribbon on the cover.most popular conductress, sylvia mitchell, tramways, red cross, events, broadway park, greyhound racing, advertisements

Documents and Photograph donated by the Woodhead family. Dorothy Edhouse was the only child of James & Frances Hill, who were Sylvia Woodhead's grandparents. "James Hill (Jimmy) came to Phillip Island in 1920 and purchased the Hotel, known as Woods Family Hotel. (Later, the Phillip Island Hotel in Walpole Street, now demolished). A milestone occurred whilst in his capable hands, when he installed an electric light plant, (32 volt), the first on the Island. He also made hundreds of cement bricks, when he built his own home. Later he purchased a building in Thompson Avenue, where he established a Billiard Saloon, with a small shop attached. He died in 1937, aged 68. His only child Dorothy Edhouse, is now 95 and has made arrangements to have her ashes added to her fathers' grave." This was added to the photograph of James Hill and Frances Edith Hill - not sure what date it was compiled by Richard Woodhead. Frances died in 1960. The write up was take from "Garden of Memories" by Edith Jeffrey. Four documents/photograph relating to Cr J O Edhouse and his wife Mrs Dorothy Edhouse. Also came with accompanying letter from Sylvia Woodhead. 361-01: An Invitation to a Dinner at the Isle of Wight Hotel - 26/11/1943 - on the occassion of the visit of Delegates to the Gippsland Shires and Boroughs Development Association Annual Conference. 361-03: Identity Card for Dorothy Symes Edhouse. 361-04: Circular from the Liquid Fuel Control Board dated 21st February 1942. 361-05: Photograph of James & Frances Edith Hill. A note saying that James (fondly called Jimmy) came to Phillip Island in 1920 and purchased a hotel - see history below. james & frances edith hill, shire of phillip island dinner invitation, identity card, cr j o edhouse, mrs edhouse, sylvia woodhead, documents

12 page pamphlet printed on light grey paper with blue SEC logo and blue border on each page that has text. Titled "The Victorian State System of Electricity and Fuel Supply", with subsidiary title "Its Objectives and Progress". Dated January 1938. Produced by the State Electricity Commission of Victoria, Sets out the constitution and objects of Victorian State Power system, notes Act of Parliament of 1918, Yallourn, Newport B, Richmond, Ballarat and Geelong Power stations, Sugarloaf - Rubicon Hydro electric stations. Other subjects are Rural Electrification, system growth, tariffs, and financial stability, Kiewa, and future planning. Only mention of the tramways is the amount of fixed capital involved - L328,000. trams, tramways, power supply, secv, electricity generation

Cast iron stoves burn solid fuel such as wood or coal, and are used for cooking and warmth. The stoves have a firebox with a grate where the fuel is burned. The hot air flows through flues and baffles that heat the stove top and the oven. Before cast iron stoves were invented, cooking and heating were carried out in outdoor open fires, and later, in fireplaces inside the home. In 1642 the first cast iron stove was manufactured in Lynn, Massachusetts, where molten cast iron was poured into a sand mould to make rectangular plates that were then joined together to make a box. Benjamin Franklin invented the more efficient Pennsylvania stove in 1744, and this efficient design is still used today. After the mid-19th century cast iron stoves were produced with burners in different positions, giving varied temperatures, so a wide variety of foods could be cooked at the same time at the most suitable heat, from slow cooking to baking scones. In contemporary times people the new wood-burning stoves had to meet the anti-pollution standards now in place to protect our environment. By the 1920s gas cookers were being introduced for domestic use, and by the 1930s electric home cookers were being offered to householders. PLANET STOVES In August 1925 the firm Cox and Rizzetti, Stove Works, and also Sydney Road, South Melbourne, advertised in the Brunswick and Coburg Leader of November 11, 1925 as "formerly with Harnwell and Sons" and as "specialists in solid cast iron Planet stoves ... which merit an inspection from builders and householders". The firm continued in business and was mentioned as sponsors in the King Island News in 1971. Harnwell and Sons was listed in the Victorian Government Gazette of 1894. It is curious that the firm was mentioned in an article in the Sunrasia Daily of June 14, 1934 titled 'Planet Stoves' as a manufacturer of Planet Stoves. This Planet No 3 stove is an uncommon example of cooking equipment used in kitchens in the early 20th century, as the firebox is above the oven rather than beside it. The cast iron combustion stove is significant as part of the evolution of domestic cooking. Previously cooking was mostly carried out in outdoors in open fires, and later in fireplaces indoors. Cast iron stoves are still used today and have additional features such as thermostats to monitor and maintain temperature, water heating pipes connected, and environmentally approved anti-pollution fittings. Stove; a compact, blackened cast iron combustion cooker, installed within a fireplace and enclosed by bricks on both sides. The upright rectangular stove has a flat top with three round, removable cook plates and a flue connected at the back. The front has three doors with round knob handles; a swing-down firebox door above a sliding ashtray, and two side-hinged oven doors above a sliding opening. Inside on the side walls are two pairs of runners. Behind the pair of doors is an oven with two pairs of rails and two removable metal shelves. The stove has cast inscriptions on the chimney flue and on the front of the right hand side stove door. The model of the stove is The Planet No 3, made in Melbourne.Chimney flue, "[within rectangle] THE / PLANET" Stove door, "(within oval) PLANET / No 3"flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, stove, cast iron stove, combustion stove, wood-burning stove, wood stove, wood oven, solid fuel stove, cooker, the planet, planet, planet no. 3, kitchen equipment, baking, domestic cooking, cooking equipment, food preparation, planet stove, planet cooker, cooking range, slow combustion stove, antique, range cooker, cox and rizzetti, harnwell and sons, melbourne manufacturer

A small number of heavy cast iron weights and two rods remain at the Point Hicks. The weights and rods were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene-fuelled light turning. They were attached to a cable or chains and moved vertically in similar fashion to the way weights move on grandfather clocks. As the weight fell, the optic clock was driven and the lens was turned. To keep the clock turning, the weight needed to be wound back up to the top of its travel. The cables and weights in this lighthouse were visible as they moved through the length of the tower up to the lantern room. It was usual for systems to move inside a tube extending up to the top, but in this case the tower’s cast iron spiral staircase, which is supported on cantilever cast iron brackets set into the concrete wall, spiralled around the space in which they moved. Lighthouse keepers had the arduous job of having to constantly wind the clock to keep the light active, and at least two keepers needed to observe a strict roster of hours. When electric motors were invented, all of this became redundant and the motors were able to turn the optic for as long as there was power to drive them. In December 1964, the original 1890 Chance Bros kerosene-fuelled light and clockwork mechanism were replaced by small electric motor, and the number of keepers reduced to two. The six circular weights and rods originate from the obsolete system and may have been part of a larger set. Wilsons Promontory retains seven of its original set of ten weights, all of which are detached from the tower’s weight tube. Cape Schanck has a set of fourteen weights remaining in situ as well as another four detached weights, which have inscriptions . One weight is displayed in the lantern room at Cape Otway. The Point Hicks weights have first level contributory significance for the insights they provide into the superseded technology and operations of a late nineteenth century lighthouse. They are well provenanced and are significant for their historic value as part of the lightstation’s Chance Brothers optical system installed in 1890.PHLS0005.1 Round cast iron weight with flat base used for lens clock-work mechanism attached to a bent metal rod. PHLS0005.2 Removable round cast iron weight with flat base used for lens clock-work mechanism stored above the other weight.

The VN Commodore was available in Executive, S, SS, Berlina and Calais specification levels, although a more basic SL model (opt. code A9K) was supposedly offered to government and fleet buyers, as it was not officially listed as part of the Commodore range. Changes in the relative values of the Australian dollar, the Japanese yen, and the US dollar made it impractical to continue with the well-regarded Nissan engine of the VL. Instead, Holden manufactured their own 90-degree V6 based on an old Buick design from the US, although initially it was imported. The 5.0-litre V8 remained optional and received a power boost to 165 kW (221 hp). Both these engines used multi point GM EFI and the V6 using 3 coil-packs for ignition. Holden and HSV developed this car as the basis for racing in Group A Confederation of Australian Motor Sport events. While the minimum number of cars built to qualify in Australian Touring car Championships, with modified body kit, brakes or engine is 500, only 302 VN were built but CAMS granted an exemption allowing them to compete.Holden and HSV had worked hard to develop this car to be a serious competitor to the Skyline, Ford Sierra and the BMW which had dominated in the previous years. This was to be the Holden’s answer and coincided with the return of Peter Brock back to the Holden team from 1987.Mechanically the cars were fitted with reworked version of Holden’s 4.9 litre V8. The engine block was cast for additional strength, modified cylinder heads roller rockers and high fuel flow fuel injection was applied. Output was 215 kw at 5200revs and, though at today’s standard, that is not that much it was very impressive at that time. The drive was through a six speed ZF gearbox with a heavy duty racing clutch and a limited slip differential.Under the Hawke government's Button car plan, which saw a reduction in the number of models manufactured locally, and the introduction of model sharing, the VN Commodore was rebadged as the Toyota Lexcen, named after the late America's Cup yacht designer, Ben Lexcen. Subsequently, the Toyota Corolla and Camry were, similarly, badged as the Holden Nova and Holden Apollo.Red executive 4 door sedanHolden Lion and stone emblem grille centre, Commodore boot LHS, Lion and stone emblem boot RHS.vehicle, vn commodore, holden, car

This photograph shows men fishing in the Snowy River at Marlo - possibly at Bream Point. The man in the white coat is Lancelot Herbert. Lancelot Herbert came to Orbost in 1886, taking up a partnership with local store-owner George Temple. After Mr Temple’s death in 1891, Lancelot took over the store and progressively developed Herberts Snowy River Stores which grew into a department store of several shops along Nicholson St. He also had small shops at Cann River, Noorinbee and Genoa which were run by members of his family, as well as a carrying business and fuel outlets. Lancelot died on 2/6/1911 and his wife Martha [died 1945] are buried in a joint grave in Orbost Cemetery. (info. Noreen and Lindsay Thomson. More from "In Times Gone By' by Deborah Hall)This item is associated with the Herbert family very early settlers in the Orbost district. It is also associated with Marlo which has always been a popular fishing destinationA small black / white photograph of four men fishing from a river bank. Three are sitting and one is standing.on back - Lancelot Herbert in white coat fishingfishing-marlo herbert-lancelot

The American Truck History Association is an international organization, with over 21,000 members in the United States, Australia, Canada, and 20 other countries worldwide. A.H. McMullen & Co P/L, established by Arthur McMillan in February, 1951, had a long history as transport operators in Orbost and Gippsland districts. The company became Gippsland's largest transport company. It carted timber from the Orbost/ Cann River district district sawmills to the railway station. Two trains a day left the sloaded with timber. Beans were carted from Fisher's Bean Factory to Melbourne and Sydney. Cream from the farms was transported to the butter factory and for almost twenty years Fuel was carted from Melbourne to the RAAF base at Sale by McMullens. In 1970 the company was sold to F.J. Stephens and then to Mayne Nickless Transport. (ref.Deborah Hall "In Times Gone By') A.H. McMullen was a significant business in the mid 20th century in Orbost. This book is a useful reference source.A 40pp book with a dark blue cover titled "The Gearchange". It is a "Classic Edition Issue No. 2" and features A.H. McMullan & C0 P/L. It has a cost of $20.00. It contains illustrations, photographs and text.transport mcmullen-transport-orbost trucking

Photos of abseiling down the Gas and Fuel building that were on the corner of Flinders St and Swanston St. It was an event for Legacy Week 1989. See also the training that occurred prior to the event - photos 00486 and 01409. Ron Barassi abseils for Legacy joined by staff member Carol Shaw and Legatee Peter Heeney. A label states it "was a Legacy versus Radio personalities abseiling challenge". Media team was Fox's Wally (Paul) Weissel and Ken Cavanagh and Triple M's Andy McClean. Aided by Williamstown Commando Company with training at Nidrie Quarry. Ron Barassi participated in many events for Legacy over the years, he had been a young Legatee after his father was killed in action at Tobruk in World War II, aged 27. Two photos also featured in the President's Highlights Report in 1989.A record of some important personalities giving their time to promote Legacy in 1989.Colour photo x 13 of a junior legatee and Ron Barassi abseiling.legacy promotion, ron barassi, legacy week

The 8th/13th Victorian Mounted Rifles was raised as a regiment of the Royal Australian Armoured Corps on 1 May 1948 with Headquarters in Melbourne and squadrons in Sale, Benalla/Wangaratta and Albury. In 1955 Regimental Headquarters moved to Wangaratta and a second squadron was located at Albury. The Sale squadron transferred to 4th/19th Prince of Wales’s Light Horse. In 1977 8/13 VMR Regiment was reduced to an independent squadron A Squadron 8th/13th Victorian Mounted Rifles and in 1991 was linked with 4th/19th Prince of Wales’s Light Horse forming the VMR Squadron of that regiment.Members of the Women’s Royal Australian Army Corps (WRAAC) were posted to Army Reserve units in the 1980s and 1990s. They were rarely posted to Armoured Fighting Vehicles (AFVs) but were invaluable in the A1 Echelon driving fuel, ammunition, ration and water supply vehicles. Colour photograph of soldiers of ' A ' squadron 8/13 Victorian Mounted Rifles on parade at Buna Barracks Albury 1986. Sergeant D. Reynolds ( WRAAC ) at left; Corporal B. Lewis at right.

Annual report on activities and financial performance of Kelaston, including the closure of the laneway behind Kelaston in preparation for the expected rebuilding, appointment of Dawn Veale, Rod McDonald, Deborah Hoover, Jane Brownfield and Anne Johnson, challenge issued to other centres to find the longest serving volunteer with no one beating Avenel McClure's record of 59 years with the Ballarat Auxiliary starting as a driver, Terry Fraser seconded to Mirridong, farewell to Teresa Skyrpko who use to carry bags of coal to fuel the stoves when she began 34 years ago, 4 residents attended a holiday at Halls Gap, Port Phillip Bay cruise for 2 residents, three people celebrated turning 100 (or more), establishment of an awareness program of vision impairment for Ballarat primary school students and the Low Vision Clinic in Horsham began operations.1 printed volume with illustrationskelaston home (ballarat), association for the blind, corporation records

Alan McArthur from the CSIRO began his experimental burning program in the late 1950s near Canberra and published his landmark paper in 1962, “Controlled burning in eucalypt forests”. Leaflet No. 80, as it was known, proved a turning point for forest and fire managers across Australia. It led to the McArthur Forest Fire Danger Meter (FFDM) which first appeared in operational use in 1967 as the Mk 4. The CSIRO had developed its semi-automatic aerial incendiary machine dropping small capsules, with the first trial from a fixed-wing Cessna 337 at Manjimup in December 1965. In April 1969, the Forests Commission borrowed the second prototype of the CSIRO machine to carry out fuel reduction burning at Orbost. The success prompted the purchase of their own machine in 1970, which now sits in the Altona Museum. Pioneering machine in the development of aerial ignition in AustraliaAerial Incendiary Machineforests commission victoria (fcv), planned burning, bushfire aviation, bushfire