When acquired, this case held numerous pieces of surgical laparoscopy equipment. The equipment inside the case was used by Dr Noel Clarkson Holmes sometime between 1964-1967, when he was training under Dr Sidney Page at the Princess Alexandra Hospital in Brisbane. This case was purchased at the same time to carry this equipment, and has been repaired several times by Dr Clarkson Holmes.Brown leather briefcase. Briefcase is fastened by combination lock latches at the front. Inside of the case is lined with yellow felt. There are three accordion style storage pockets with leather trim inside the lid of the briefcase. A strip of orange tape has been attached to the outer top of the case, which carries the handwriting 'DR. N. HOLMES'. A similar strip of white tape is also attached to one side of the briefcase, which carries the handwriting 'Dr. N Holmes'

These items were part of a collection of instruments used by Dr Michael Kloss in his medical practice. Dr Kloss subsequently donated this collection to the College.Two small metal towel clips. The clips resemble small sets of scissors, with a ratchet adjacent to the handle to lock them at particular apertures. The end of each arm of the scissors bends upwards 90 degrees, then towards the centre of the clip at another 90 degree angle. Each arms tapers to a sharp point, with the ends of the points facing and adjacent to each other. Both clips are engraved with the word 'Kloss'. Inner aspect of each clip is engraved with the word 'GERMANY'.'Kloss' 'GERMANY'obstetrics

a. Black wooden case, brass handle on top of lid, brass hinges and lock, lined with black ( faded) velvet. B. Cornet, engraved with leaves and flowers. Engraved on top ' F. Besson, Brevetee, 198 Euston Road, London.' On bell ' Presented by the citizens to James Northcott Bandmaster of the Sandhurst Volunteer Band in recognition of his musical abilities. Sandhurst Dec. 8 1871. Cornet box contains 7 additional parts of the Cornet. ( see photo )F. Besson, Brevetee, 198 Euston Road, Londonmusical instruments, wind, cornet ( besson ), james northcott, sandhurst, volunteer band, bendigo, music, presentation

Part of the 'Mann' collection, used for time keeping by employees in the J. Mann & Sons General Store in Wodonga High Street in the c 1960s. J. Mann and Sons was first established as a farm produce store in 1921. The range of products was extended in the 1930s and included groceries and hardware, as well as the first petrol bowser in Wodonga outside the store. After WWII, the premises were extended and the range of products continued to increase. In the 1960s the Mann Family opened a new supermarket in Wodonga, in addition to the hardware business, providing steel, plumbing and industrial supplies, and they employed over 100 people at one stage. With changes in the retail industry, the Mann Family sold the main hardware business to Bunnings and the steel and rural produce business to the Kelly brothers in 2006.The Amano time clock has local significance due to its use in the J. Mann & Sons General Store in High St, Wodonga and the association with the prominent Mann family.Green metal electronic Amano time clock used by employees in the J. Mann & Sons General Store in Wodonga, with a brown clock face and light coloured numbers. Two labels on the lower part of the front surface with a horizontal lock between them, and a small metal plate on the proper left side with the model and serial numbers, plus "S 422" written in black marker below. Slot in the top surface of the time clock for the employees' time cards."AMANO" - on the clock face "TIMETEK SYSTEMS / Phone or Fax: / BU..NESS / BISCOM / COMMUNICATIONS" - on the lower front "Model 6733 Serial No 23229 / Volts /240 / Watts 5 / Hz 50 / AMANO CORPORATION / MADE IN JAPAN / S 422" - on the lower proper left sidemann, general store, wodonga, time clock, commerce, local business, high street, j. mann & sons

This sewing machine was bought by Alex Craig's dad in 1942 for his wife whom he married in 1943. Alex's grandmother used it in 1942 to make button holes.Historical: Type of machine used by S.E.C.V. wives living in Mt Beauty in the 1940's, 1950's and 1960's. Ladies made the family's clothes and sewed for the Annual Church and chook fetes e.g.. children's clothes and dolls clothes. They bought dozens of dolls and made 'fairy' dresses for them using coloured netting.Green & white box containing black & silver metal with 4 parts for attaching to Singer sewing machine for sewing button holes."Singer Buttonhole Attachment" on green 'cloud' top of box. "The Singer manufacturing Company" on green 'cloud' on side of box. "For Light Manufacturing and Home Use" on green 'cloud' on side of box. "Made in Great Britain" on white top half of end of box & teen 'cloud' below end of box is "Singer / Buttonhole Attachment / No. 86662 / For Singer Lock Stitch/ Family Sewing Machines.singer manufacturing co.. clothes. fetes. domestic. sewing.

Silver coloured plate with Guangzhou Ocean Shipping Company logo and a picture of ship depicted. Case is decorated with fine textile patern and has a simple metal lock. A square piece of paper is adhered to the interior of the lid and contains Asian and English writing noting ‘Many thanks for you fully support and sincerely cooperaticn in the past.’ The plate sits in a red velvet mount which can be lifted out. A second compartment below houses a wooden varnished stand also in a red velvet support.On paper documentation in box ‘MANY THANKS FOR YOUR FULLY SUPPORT AND SINCERELY COOPERATICN IN THE PAST.’ Plate engraved ‘1961 Asian characters 1991./COSCO/ GUANGZHOU OCEAN SHIPPING CO. PMA 0208/s in greylead on the lower right corner of the paper documentation. Back of plate: WMA67 white sricker PMA0208/1 ink and B72gifts

This item was in use before electricity and was manufactured after the flat stove irons.The weight of the iron base, is heavy, helping in smoothing out crinkly material being ironed. This item permitted ironing of clothes to be separate and away from heating stoves. It permitted greater flexibility for ironing clothes and permitted more control (consistency) of the temperature of the iron.Historically and significantly this item enforces the relative isolation of the Kiewa Valley and period when and where this domestic item was in use(manufactured circa 1950). A rural setting with mining, beef , milk and tobacco production in the early 1900s. Even though the community was in a rural setting, the standards of dress was the same as in the bigger towns and cities. Social and religious mores and values demanded that the personal appearance be clean and crisp no matter where a person was living or working. Heavy laborious work was considered by some religions as virtuous, therefore the heavy and tiring work of ironing during this period had its rewards. Rural areas where the last to be connected to electricity and therefore this item was a domestic necessity far into the 1950's.This iron has a steel base and a metal body coated with green coloured enamel. The wooden hand grip is painted dark green. The kerosene (spirit) container is a chrome metal cylinder with a flat bottom and top. The top has a small filler/air plug is located on the top side. There are two control knobs located next to and under the metal cylinder. The close to the cylinder is a lock which locks the top lid of the iron and the other knob controls the airflow to the heater rodOn the base of the handle "PEERMAN" and below this P/46, C.I. Thomas & Son Pty Ltd household, ironing, domestic kerosene, dry cleaning

This book was given in 1886 as a prize to Annie Egerton from Allansford State School. The prize was for recitation. Allansford State School No. 3 was opened in 1856 as a National School and is still operating. Allansford is about ten kilometres from the Warrnambool city area and most of it today is within the boundaries of the City of Warrnambool. John Jones was the Head Master of the school from 1867 to 1891. No details have been found on Annie Egerton or her family This book is of interest because it concerns 19th century Allansford State School, Head Master John Jones and pupil Annie Egerton. It is also a book of antiquarian interest. This is a hard cover book of 436 pages. It has a green cover with gold and black ornamentation and black and green lettering. The pages are edged with gold colouring. The book has 36 chapters telling the story of the merchant, James Meetwell and some pages at the back giving details of other books available from the publishers, Ward, Lock & Co. The cover is somewhat soiled. There is an inscription inside the front cover with handwriting in black ink and the word ‘Reciting’ written in pencil on the second page. ‘Allansford S. School, 3, Presented to A. Egerton for Reciting, 19-4-86, J.E.Jones, teacher’ ‘Reciting’ annie egerton, allansford primary school, john jones,, allansford state school, history of allansford

Hugo Wertheim (1854-1919), was a merchant and manufacturer and was born on the 12th July 1854 at Lispenhausen, in the German electorate of Hesse-Kassel, son of Meyer Wertheim and his wife Minna, née Heinemann. Hugo reached Melbourne in October 1875. He soon began advertising, from premises at 39 Flinders Lane East, as agent for his father's cousin Joseph Wertheim, a well-established manufacturer of sewing machines. Hugo returned to Germany where he married Joseph Wertheim's daughter Sophie Emilie (1864-1953) on 30 August 1885 at Frankfurt. the couple then came to Melbourne. In a short time, with extensive advertising, Hugo established a substantial business, selling sewing machines, bicycles, pianos and other mechanical devices, under brands such as Wertheim, Electra, Planet, Griffin and Hapsburg. He also mounted elaborate displays at agricultural shows and in 1901 at the Pan American Exposition, Buffalo, United States of America. O. C. Beale worked with him before setting up his own piano business in New South Wales. Hugo continued to own 25 per cent of one of Beale's companies, which became Wertheim's Queensland business. In 1908 Wertheim opened a large, innovative piano factory at Richmond, Melbourne, intending to produce 2000 pianos and player pianos annually, predominantly using Australian materials. In laying the foundation stone, Prime Minister Alfred Deakin observed that “few men with such opportunities for a life of ease would have embarked on such an enterprise” Hugo died of chronic hepatitis on 11 July 1919 at his home at South Yarra, his wife, two daughters and three sons survived him; Herbert Joseph (1886-1972), the eldest, continued the business. Rupert became a share broker and went on to represent Victoria in inter-State tennis in 1913-27 and Australia in Davis Cup matches against Czechoslovakia in 1922. The piano factory closed in 1935, becoming a Heinz food processing plant and in 1955, GTV Channel 9 studios and offices.Early Australians had to be self-reliant in regards to making and mending their clothes and utensils. This sewing machine was one of many items used that exhibit the skill and craftsmanship of the women in these early families. A sewing machine was a necessary part of each home and this item demonstrates how women of the time managed had to become self-reliant in the repair and making of their families clothes to make their household budgets go further.Wertheim sewing machine in carry case, hand operated with two spindles, handle with locking pin, which turns lever between spokes of main handle, hand brake. The machine is table-mounted with a Turkish walnut base. The base can be attached to a cast iron table with a foot treadle as an optional extra. The walnut base has marquetry to the front set out as a measure for material. There is also an accessory box inside the carry case containing 20 additional items for use with the machine. Wertheim brass trademark badge riveted to the body of the machine of a crouching dwarf with a hammer with the name of the company Wertheim and Frankfurt. Gold filigree decoration in gold paint adorns the main body of the machine. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, sewing machine, hand operated sewing machine, crank handle sewing machine, wertheim, dressmaking, taylor, domestic, clothing, hugo wertheim, joseph wertheim

Articles for RHSV Bendigo Brand Newsletter Aug 1973. 1. Market Square - reference to Messrs Reid & Co.; pudlers' activity on that area; Hunter's puddling machine in area; weighbridge 1855; vegetable market; hay and corn market; wood market; City Fire Brigade; City Retail Market; City Lock-up; City Hall (1885). 2. Typewritten article ''Looking Back'' (see Mosaic #6545). 3 Handwritten notes on ''The Pearl mine'' - see Mosaic # 6543document

Object: Enclosed in envelope: Death brooch of Elizabeth Lansell. Rectangular brooch, black enamel engraved with gold scroll work. Brooch has lock of hair enclosed in clear rectangle in centre of brooch. Engraved on back : E. Lansell, died Feb. 26th. Aged 88 yrs. Written on front of envelope in pen: Born Elizabeth Rammell 1769 Married William L. Elizabeth Lansell's death brooch she was our great, great, great, great, grandmother.E. Lansell, died Feb 26th. Aged 88 yrs.personal effects, fortuna, family history, bendigo, fortuna, lansell, elizabeth lansell

A black briefcase embossed with Legacy. There are no details of when or where this case was used.This item is representative of a case that would have been used by staff/ board members/ legatees at one period in time.Crocodile imprint, black leather brief case with "LEGACY" painted in gold on the front of the flap. The flap is affixed shut via two metal clips. The clips can be locked with a key. (Key not located with case) The case has a three fold leather handle attached via two metal D rings. Internally the case is lined with a tan leather flap on each side. The internal front flap as a small sleeve attached. The lip of the top of the bag is scalloped and showing signs of wear. "LEGACY" painted in gold on front flap "CHENEY ENGLAND" embossed on front of metal clipslegacy promotion, souvenir

Faded, colour photograph of the 2002 Zone Athletics Representatives. Their names are: Back: Karra Bourke, Katie Allen, Corinne Packham, Casey Veal, Kate Hewett, Casey Buck, Claire Hudson, Hannah Apps. Middle: Jessica Wardle, Brianna Dalrymple-Monro, Kyle Owen, Dylan Holliday, Jamie Lock, Henry Anderton, Emily Zerella, Paige Donnellan. Front: Jayden O'Brien, Bradley Clayton, Jackson Bissett, Seb Anderson, Noah Dunlop, Brett Monti.education, primary, golden square laurel st p.s., golden square laurel street p.s. collection - photograph - zone athletics representatives 2002, karra bourke, katie allen, corinne packham, casey veal, kate hewett, casey buck, claire hudson, hannah apps, jessica wardle, brianna dalrymple-monro, kyle owen, dylan holliday, jamie lock, henry anderton, emily zerella, paige donnellan, jayden o'brien, bradley clayton, jackson bissett, seb anderson, noah dunlop, brett monti

Diggers & Mining. The gold licence. The Government Camp. Slide: On the more important goldfields, as the number of diggers grew, the Commissioners' establishments were increased, and permanent buildings were erected at their headquarters. The group of tents and buildings forming a Commissioner's headquarters became known as the Government Camp. The Camp included the office of the Commissioner, the licence office, the escort office, the lock-up, staff quarters, and the barracks of the police and any soldiers attached to the Camp. Markings: 14 994.LIF. 4. Used as a teaching aid.hanimounteducation, tertiary, goldfields

PERSONAL TRUNK OF CAPTAIN PETER SPENCER HAYMAN MCThis trunk was owned by Peter Spencer Hayman, who was regarded as a ‘Tobruk hero’. Hayman was the son of a Bank manager, Spencer Lewis Hayman and Agnes Lindsay Hayman. He was born in Exeter S.A. on 23/11/1916. He enlisted in the Australia Army at the age of 23 on 13/05/1940. His service number was VX14987. Hayman was a leader of a fighting patrol and served in multiple sites in Syria and Lybia. During his service in Lybia he lead his campaign through great difficulty and bravery in Tobruk. Although wounded by a grenade, he continued to lead his men into an enemy stronghold until resistance from a joining post compelled him to break off the engagement. He successfully brought his party back with very few casualties. Hayman was awarded the military cross in 1941. He was a Lieutenant when awarded, and was made captain of the 2/24 Australian Infantry Battalion shortly afterwards. He was killed in action on the 11/07/1942 and is buried in the El Alamein war cemetery. His father was flown to London to receive the medal. The inscription on his headstone reads; “Beloved son of Spencer and Agnes Hayman of Bendigo” (AII.A.21. – cemetery/memorial reference number). As an item owned by a ‘Tobruk hero ’ who was awarded the eminent military cross for bravery, ‘forceful leadership’ and ‘splendid courage’, this trunk is of national historic and social significance. It also has great interpretive capacity as an item that speaks of an impressive military story. Standard Army issue trunk. 88cm L x 51cm W x 33cm D. Dull grey in colour. There is provision for a tray to be fitted just under the lid. This tray was the same physical size as the trunk. The base has 2 cleats (88cm x 5.5cm), made of timber, to keep the trunk off the ground. An additional hasp and keeper have been fitted (near the centre of the lid) to hold it shut. The original type lock needed a key and were not very serviceable.P S H VX14987 408

Badge - issued by the Lions District No. 201, Vic, featuring a map of Victoria with the letter V and number 1 included in the map, featuring a Box Hill toastrack style tramcar under the badge with the numbers 95-96 on the front of the tram. Gold badge with brown paint infill in the map of Victoria and a yellow paint infill on the tram finished with a gloss varnish. Has a pin clip on the rear with a locking mechanism. Made by Douglas batches of Melbourne - has their phone number on the rear.trams, tramways, box hill, badges, lions club

Used for vaginal hysterectomy.Set of metal forceps. Item very broadly resembles a pair of scissors, with two finger grips at one end, and cutting teeth at the other. There is a ratchet on the shaft of the forceps just below the finger grips to lock the forceps into position. The cutting end of the forceps slants away from the body of the forceps at a 45 degree angle, with each forcep blade having five cutting 'teeth'. the End of each blade is rounded at the tip, above the teeth. Engraved text on the forceps reads 'MAYER & MELTZER LONDON'.'MAYER & MELTZER LONDON'

The fishing spot known as The Lodge was accessed, for many years, via private property. This article is about an on site meeting, who attended and what was said in regards to the upgrading of a road for access to the river. Includes a letter to the Editor from Ronald Irvine stating their position. Enquiries made on March 11th 2021 with Ronald Irvine revealed that the road had deteriorated and vehicles were becoming bogged, requiring the farmer to pull them out with a tractor. Council were reluctant to fund repairs and the result was that the gate was locked and public access no longer available.Significant because it is a record of community and government discussion about community access to a popular fishing location on the Curdies River.Two page newspaper article from the Cobden Times March 5 1986peterborough, curdies river, the lodge, ronald irvine, the lodge fishing, timboon anglers club, john irvine, the cobden times, 5 march 1986

The Crane foundry opened some time before 1827 and was known as Atherton’s Foundry, run by James Atherton and Henry Crane. Initially it was a brass foundry, but by 1827 iron castings were also produced on the site. The main products were castings for the building industry, ironmongery and brassware. In the 1830s castings for the hand tool and lock industries were added to the product range and by 1836 Henry Crane had taken control of the business. The company became known as the Crane Foundry in 1847 with its own registered trademark. By the 1850s iron weights were produced, and a design was registered in 1872 with roundels decorating the edge. Brass weights were also produced, mainly after the regulation of 1890 that required weights of 2oz. or less to be made of brass. In the early 1900s the foundry began to produce castings for electric motors and continued to do so throughout its life. The Crane family continued to control the company until 1917 when William Cyril Parkes of lock makers Josiah Parkes & Sons Limited, Willenhall became a majority shareholder. Things were going well until the company’s liabilities spiraled out of control with the rise in electricity and gas prices along with the loss of two of the company’s largest customers. The factory went into liquidation and then closed in 2006 an end to one of Wolverhampton’s oldest companies.An item made by one of England's foundry’s based in Wolverhampton that exported items all over the world for many years. The scale gives a snapshot into the commercial life not only of England by Australian colonial life before Federation.Beam scale with three weights (4lb, 2lb, 1lb), metal tray, corrodedMarked on 2lb weight "Wolverhampton Crane Foundry" flagstaff hill, warrnambool, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, scale, beam scale, pounds and ounces, imperial weight, grocers scale, domestic scale, henry crane, crane foundry

This is a mantel clock used probably in the dining room or lounge room of a house. It would have been a common item in a household in the 20th century and was often an heirloom passed down from grandparents. This type of clock is an attractive item and is still regarded as highly desirable today.This clock has no known local significance but is retained as an attractive and historical item and serves as an example of a high quality household object of the past. This is a black wooden clock with a rectangular base with ornamental metal corner pieces and two ornamental gilt metal patterns. The clock has an overhanging rectangular top with two gilt handles on the side. Also on the sides of the lock are two green inset faux columns with two metal ornaments in between. The brass mechanism at the back of the clock has four wheels. The clock face has a glass front, black numbers and metal hands. There is a strip of brass around the outside of the face. There are two key holes on the face. 'Sessions'warrnambool, mantel clock

This is a WW1 stand for mounting a .303 rifle, to train soldiers in shooting.This device consists of two parts; 1. Top part has an adjustable 'arm' . At the end of each arm is a leather covered 'U' section. Under the arm is a large threaded rod and knurled knob, this is to adjust elevation. At the center of the arm is a pivot that can lock into position. This top section is mounted on a tripod, it can be removed. 2. This is a steel tripod made out of 'T' section steel. There are fixed cross braces about 40 cm fom bottom. The top has a tube section within which the upper arm mounts.Marked on one leg is "XXI". Believed to be from 21st Bn. AIF. on the top of that leg is a very small arrow head.ww1, training, .303 rifles

This desk was donated to the MTSV in 2017 by a descendant of Padre Oliver, Chaplain from 1930-1960.This desk belonged to Rodney Oliver and is believed to have been used by Padre Oliver and his wife while Chaplain, and the family resided at the MTS and thereafter in subsequent parish postings. The desk makes a link with one of the longest serving Chaplains who had a significant influence through the intense period of operations early - mid 20th C. The Padre's influence was substantial. The desk is also believed to have been used by son Rodney Oliver who also served the Mission as Chairman in the later 20th C.A four drawer leather topped desk with detachable unit comprising double sliding door lockable cabinet with small bookshelf backed with shallow pediment. Sorting / sectioned pigeonhole interiors to the top cabinets see images. The main table desk appears to be of a different wood with green leather inset to top surface and heavy legs. Drawers with heavily decorated brass handles. The top cabinet features finer cabinetry and darker colour wood or stain which could be cedar.with simple narrow reeded decoration. interior two pigeon holes with labelsfrank leslie oliver, padre oliver, chaplain, desk, mission to seafarers, melbourne, seamen's mission, flinders street, padre frank leslie oliver

This book, a sequel to ‘The Swiss Family Robinson’ by Henry Frith, was a prize given to Frank Ward in 1901. His school, the Warrnambool Academy, was established in 1899 by Richard Lawson and William Oakley and was eventually situated at ‘Upton’ in Canterbury Road, Warrnambool. The Academy later incorporated the former Scott’s Warrnambool College and Stanley’s Warrnambool Grammar School. This private school closed in 1911. William Oakley later joined the Victorian Education Department and Richard Lawson had a distinguished academic career in teacher education in Melbourne and New Zealand. No details are available on Frank Ward. This is a hard cover book of 295 pages. The cover is dark blue with gold printing and ornamental gold borders on the front cover and spine. The book has an introductory chapter, 28 chapters of story and an Epilogue. In the back pages there are lists of other books published by Ward, Lock and Co. The book contains many black and white illustrations. There are two blue stamps of the Warrnambool & District Historical Society and on the first page a flyleaf from the Warrnambool Academy printed with gold print and borders and with handwriting in black ink. The cover is slightly faded and marked. ‘Warrnambool Academy, Labore et Fide, First Prize awarded to Frank Ward for Latin, Principals, Richard Lawson M.A. & W.M. Oakley. 17/12/1901’ warrnambool academy, richard lawson, william oakley, frank ward, history of warrnambool

The anchor is one of four that were carried by the FALLS OF HALLADALE when she was wrecked near Peterborough in 1908. This Rodger’s Anchor was raised from the wreck site by Flagstaff Hill divers (Peter Ronald, Colin Goodall and Gary Hayden) in 1974 and is on permanent outdoor display at the Maritime Village. The imposing 2-tonne artefact required a raft of fourteen 44-gallon drums to raise it from the seabed before it was towed by a crayfish boat to the wharf crane at Port Campbell for loading onto land transport. Following Lieutenant William Rodger’s patent in 1831, anchor design moved away from the separate attachment of straight arms and flat flutes to each side of a long shaft. Rodger’s innovation included the forging of both arms and their flutes as a single uniformly curved piece which was then attached to the crown of the shank by a thick horizontal bolt. The two-inch diameter hole for the securing through-bolt at the crown is clearly visible in this example, the bolt dislodged by corrosion and now missing. The FALLS OF HALLADALE was a four-masted, iron-hulled barque, built by Russell and Co at Greenock in 1866 for the Falls Line of Wright & Breakenridge, Glasgow. The ship was 275 feet long, 42 feet wide, with a 24 feet draft and weighed 2,085 tonnes. She was built to carry as much cargo as possible rather than for speed. Her unmistakably square bilge earned her the title of “warehouse-type” ship and her iron masts and wire rigging enabled her to maintain full sail even in gale conditions. In 1908, with new sails, 29 crew, and 2800 tons of cargo in her hold, the FALLS OF HALLADALE left New York, bound for Melbourne and Sydney via the Cape of Good Hope. 102 days later, at 3 am on the 14th of November, under full sail and in calm seas, with a six knots breeze behind and a misleading fog along the coast, the great vessel rose upon an ocean swell and settled on top of a shelf of rock near Peterborough. There she stayed for nearly two months until the pounding seas and dynamiting by salvagers finally broke her back, and her remains disappeared back into deeper water. The iron-hulled, four-masted barque, the Falls of Halladale, was a bulk carrier of general cargo. She left New York in August 1908 on her way to Melbourne and Sydney. In her hold, along with 56,763 tiles of unusual beautiful green American slates (roofing tiles), 5,673 coils of barbed wire, 600 stoves, 500 sewing machines, 6500 gallons of oil, 14400 gallons of benzene, and many other manufactured items, were 117 cases of crockery and glassware. Three months later and close to her destination, a navigational error caused the Falls of Halladale to be wrecked on a reef off the Peterborough headland at 3 am on the morning of the 15th of November, 1908. The captain and 29 crew members all survived, but her valuable cargo was lost, despite two salvage attempts in 1908-09 and 1910. ABOUT THE ‘FALLS OF HALLADALE’ (1886 - 1908) Built: in1886 by Russell & Co., Greenock shipyards, River Clyde, Scotland, UK. The company was founded in 1870 (or 1873) as a partnership between Joseph Russell (1834-1917), Anderson Rodger and William Todd Lithgow. During the period 1882-92 Russell & Co., standardised designs, which sped up their building process so much that they were able to build 271 ships over that time. In 1886 they introduced a 3000-ton class of sailing vessel with auxiliary engines and brace halyard winches. In 1890 they broke the world output record. Owner: Falls Line, Wright, Breakenridge & Co, 111 Union Street, Glasgow, Scotland. Configuration: Four-masted sailing ship; iron-hulled barque; iron masts, wire rigging, fore & aft lifting bridges. Size: Length 83.87m x Breadth 12.6m x Depth 7.23m, Gross tonnage 2085 ton Wrecked: the night of 14th November 1908, Curdies Inlet, Peterborough south west Victoria Crew: 29 The Falls of Halladale was a four-masted sailing ship built in 1886 in Glasgow, Scotland, for the long-distance cargo trade and was mostly used for the Pacific grain trade. She was owned by Wright, Breakenridge & Co of Glasgow and was one of several Falls Line ships, all of which were named after waterfalls in Scotland. The lines flag was of red, blue and white vertical stripes. The Falls of Halladale had a sturdy construction built to carry maximum cargo and able to maintain full sail in heavy gales, one of the last of the ‘windjammers’ that sailed the Trade Route. She and her sister ship, the Falls of Garry, were the first ships in the world to include fore and aft lifting bridges. Previous to this, heavily loaded vessels could have heavy seas break along the full length of the deck, causing serious injury or even death to those on deck. The new, raised catwalk-type decking allowed the crew to move above the deck in stormy conditions. This idea is still used today on the most modern tankers and cargo vessels and has proved to be an important step forward in the safety of men at sea. On 4th August 1908, with new sails, 29 crew, and 2800 tons of cargo, the Falls of Halladale left New York, bound for Melbourne and Sydney via the Cape of Good Hope. The cargo on board was valued at £35,000 and included 56,763 tiles of American slate roofing tiles (roof slates), 5,673 coils of barbed wire, 600 stoves, 500 sewing machines, 6,500 gallons of oil, 14,400 gallons of benzene, plumbing iron, 117 cases of crockery and glassware and many other manufactured items. The Falls of Halladale had been at sail for 102 days when, at 3 am on the night of 14th November 1908, under full sail in calm seas with a six knots breeze behind and misleading fog along the coast, the great vessel rose upon an ocean swell and settled on top of a submerged reef near Peterborough on the south-west Victoria’s coast. The ship was jammed on the rocks and began filling with water. The crew launched the two lifeboats and all 29 crew landed safely on the beach over 4 miles away at the Bay of Islands. The postmistress at Peterborough, who kept a watch for vessels in distress, saw the stranding and sent out an alert to the local people. A rescue party went to the aid of the sailors and the Port Campbell rocket crew was dispatched, but the crew had all managed to reach shore safely by the time help arrived. The ship stayed in full sail on the rocky shelf for nearly two months, attracting hundreds of sightseers who watched her slowly disintegrate until the pounding seas and dynamiting by salvagers finally broke her back, and her remains disappeared back into deeper water. The valuable cargo was largely lost, despite two salvage attempts in 1908-09 and 1910. Further salvage operations were made from 1974-1986, during which time 22,000 slate tiles were recovered with the help of 14 oil drums to float them, plus personal artefacts, ship fittings, reams of paper and other items. The Court of Marine Inquiry in Melbourne ruled that the foundering of the ship was entirely due to Captain David Wood Thomson’s navigational error, not too technical failure of the Clyde-built ship. The shipwreck is a popular site for divers, about 300m offshore and in 3 – 15m of water. Some of the original cargo can be seen at the site, including pieces of roof slate and coils of barbed wire.The shipwreck of the FALLS OF HALLADALE is of state significance – Victorian Heritage Register No. S255. She was one of the last ships to sail the Trade Routes. She is one of the first vessels to have fore and aft lifting bridges. She is an example of the remains of an International Cargo Ship and also represents aspects of Victoria’s shipping industry. The wreck is protected as a Historic Shipwreck under the Commonwealth Historic Shipwrecks Act (1976).A large iron Rodger’s anchor recovered from the wreck of the FALLS OF HALLADALE. It has a rounded crown, curved arms and moulded flutes. Heavy duty iron stock with round eyes at either end, fitted over shank and fixed into position by a wedge-shaped metal locking pin. Shackle missing but severed securing bolt remaining in shank. The presence of an empty bolthole at the crown junction of shank and arms confirms Rodger’s type. Corroded from 66 years submersion in seawater but otherwise structure is sound.warrnambool, shipwreck coast, flagstaff hill, shipwrecked coast, flagstaff hill maritime village, flagstaff hill maritime museum, shipwreck artefact, maritime museum, falls of halladale, rodger’s anchor, peterborough reef, 1908 shipwreck, anchor, last days of sail, great clipper ships

This Eclipse model, treadle operated sewing machine was made by the Oldham Sewing Machine Company in Greater Manchester U.K.. It was used by sailmakers for sewing sails with box shape top and slim neck. Sewing machine, foot treadle, for sewing sails with box shape top and slim neck. Brand is Eclipse. Cast iron base is bolted to square wooden table-top with drawer under table. Drawer has 3 partitions and wood fitting with 5 drilled holes for needle storage, lock has diamond shaped, decorative metal surrounds; half of inside drawer is painted black. Decorative metal stand, painted green, with 2 foot pedals; 1 foot pedal drives the wheel wheel. Padals both have "ECLIPSE" cast into the iron.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, textile machines, sailmaker's machine, maritime sewing machine

Bendigo Advertiser "The way we were" from Wednesday, July 7, 2004. Champions: this group of softballers had plenty to be happy about. This photo, taken in 1946, is of the NCSN softball team which won the premiership. The team is back row: Gertie Sexton ( forbes), Ethel Pearson (Gallagher), Betty Collins (Cannon), Margaret Ryan (Lock), Anne Donnington (Flack), Win Jennings. Front row: Mase Calligan (Purdon), Bernice Mulqueen (Bormeo), Mary Mason (Brosman), Kath Pearson (Pannell) and Rae Domington (Dalty).newspaper, bendigo advertiser, the way we were