Logs were sold to sawmillers from State forest from 1 July 1974 in cubic metres (true volume). Previously sawlogs had been sold on the basis of Hoppus volume. This simple device with two rotating wheels enabled staff in FCV offices to rapidly calculate log volumes from measurements taken in the bush of log girth and length and recorded on paper log dockets. From the early 1980s automated systems became available with the advent of cheap electronic office calculators and simple computers. An early manual device that was superseded by electronic calculatorsOffice Device Twin rollers used to quickly and simply calculate true log volumes using measurements of girth and length. An allowance could also be made for pipe defects. The top roller was for larger diameter logs.forest measurement, forests commission victoria (fcv)

This photograph of the plaque on the side of the P.S Adelaide while she was a stationary exhibit in the Hopwood Gardens from 1963 until 1984 tells the story of her manufacture and her work life up until 1963. The P.S Adelaide was launched on 21st July 1866. It was owned by J.G.Grassie from Poon Boon Station and the Officer Family of Murray Downs Station Swan Hill. The Adelaide was named after the niece of the Officer Bros, Adelaide Blackwood. The shipwrights who built her was George Linklater. The Adelaide brought wool and passengers from the wool stations on the Murray and Darling Rivers down to the Echuca Wharf. In 1872 she was sold to David Blair & Sons. She was used to bring timber from the Barmah Forest to the Echuca Wharf. She did this work for the next 80 years. In 1953 she was tied up near the Mill and left In 1958 she went to Paringa South Australia to work in the sawmill industry again. In 1960 the Echuca Apex Club and The Echuca Historical Society raised enough funds to buy the P.S. Adelaide and return her to Echuca. In November 1963 she was lifted out of the water and placed in Hopwood Gardens as this was thought to be a way of preserving her. In 1984 it was decided to return her to the water to resume work as a passenger vessel. In that time the Port of Echuca and the Echuca Wharf had been restored as a Tourist Precinct. The P.S Adelaide is extremely significant as it it the oldest known wooden hulled paddle steamers in the world. She was built in Echuca in 1866 and still operates on the Murray River today. She has worked in the Wool Industry, the Timber Industry and the Tourist Industry.Coloured photograph showing the information sign which was attached to the side of the P.S Adelaide whilst she was a stationary exhibit in the Hopwood Gardens from 1963 until 1984.On the sign is written; " P.S Adelaide/built on the Murray at Echuca for Officer Grassie &Co. Of Poon Boon and Murray Downs stations. Launched 20th July 1866. The vessel is typical of the steamers trading in the era of the Riverina and Darling River trade of 1853 to the early 1900's and which had by 1872 established aEchuca as the second busiest port in Victoria. Worked in the Red Gum logging trade until 1958 under the ownership of the Murray River Sawmills Co. She was purchased by that company from David Blair Saw Miller of Echuca in 1861. 75ft. 4 inches X 12 ft.5 inches X 3 ft. 6 inches built of 3 inch red gum planking on an angle. Iron frames 2? X 2?5/6. 30 H.P. Nominal arc original and made by Fulton & Shaw of Melbourne. Twin cylinders. 14 bore. 16 stroke Stephenson's reversing gear controlled by Captain from the wheelhouse. Locomotive type red gum wood. Master, Mate, Engineer, Fireman, Cook, and Deckhand. p.s. adelaide, port of echuca, grassie, j.g, linklater, george, poon boon station, blair, david, murray river, darling river, logging industry, officer brothers., barmah forest, fulton & shaw, hutchinson, kevin, adelaide blackwood, murray downs station

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw blade with wooden handle attached with wingnut.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture.Compass saw with wooden handle and metal blade. Small teeth. flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool, compass saw

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw with wooden handle broken and metal blade. Small teeth.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool, compass saw

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone. The subject item at this time cannot be associated with an historical event, person or place, provenance is unknown, as the maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture around the mid to late 20th century.Wood hand saw with wooden handle attached to saw by 4 rivets. No blade markings Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, handsaw, wood saw, carpenders tools, cabinet makers tools, wood cutting

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw blade with wooden with open handle blade attached with wingnut lever at side to adjust long narrow blade Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool

Blueprint copy of Survey Map detailing original Selectors' names and property locations. List of Parish map references including property bearings, distances in Links, and markings on trees. Descriptive remarks include areas marked "Farmer's Common", "Poor soil thickly/moderately timbered with stringy bark", and location of water and firewood reserves."Surveyed and plotted by N.M. Bickford, Superintendant of Mr. Hodgkinson's Field Party". "The land comprised in this survey is of inferior quality, moderately undulating, and thickly wooded. It is watered by Dandenong Creek and Deep Creek." Inset map showing location of (*proposed) cemetery on southern corner of Lillydale Road from Melbourne and Sawmill Road, later Mount Dandenong Road. (*Cemetery did not eventuate.)

Alan Richardson was born in 1853 and died in 1936. He was a sawmiller at Tabbara who built and held the ticket for the Paddle Steamer Curlip. PS Curlip was registered in 1893 and the Passenger Certificate issued on 30th January 1903 to Captain Alan Richardson by the Marine Board of Victoria entitled her to carry 25 passengers and only 10 passengers when engaged in towage service. Two children under 12 years of age to be reckoned as one passenger. He had the first horseless motor buggy in Orbost. Alan Richardson was married to Emily Dawson and had two children - Alan Jnr and Ruth.Alan Richardson was a prominent Orbost identity. He was associated with the Paddle Steamer Curlip.A black / white photograph of a man standing beside a fence covered with ivy. He is wearing a three piece suit and a seaman's type cap.on back - Alan Richardsonrichardson-alan p.s.curlip sawmilling-tabbara

Alan Richardson was born in 1853 and died in 1936. He was a sawmiller at Tabbara who built and held the ticket for the Paddle Steamer Curlip. PS Curlip was registered in 1893 and the Passenger Certificate issued on 30th January 1903 to Captain Alan Richardson by the Marine Board of Victoria entitled her to carry 25 passengers and only 10 passengers when engaged in towage service. Two children under 12 years of age to be reckoned as one passenger. He had the first horseless motor buggy in Orbost. Alan Richardson was married to Emily Dawson and had two children - Alan Jnr and Ruth.Before the First World War, few people in Australia owned or knew how to drive cars before they bought them. This International auto buggy was promoted as a useful vehicle for station owners, farmers, doctors, and town and country salesmen. It was said to be the cheapest automobile in Australia (at one third the cost of a conventional car), required much less maintenance, had durable solid rubber tyres rather than troublesome pneumatic ones, and didn’t need a chauffeur. This is a pictorial record of a "horseless buggy" which would have been a novelty in the early 20th century in Orbost. The item is associated with the Richardson family, early Orbost settlers.A small black / white photograph of a motor vehicle with a man seated at the steering wheel. The vehicle has large buggy wheels with mud guards. It is open with no windows.transport motor-vehicle horseless-buggy richardson-alan

In the 2000s Legacy released a range of Legacy Bears to expand the merchandise available for sale during Legacy Week and at other fundraising opportunities during the year. This special edition WW2 land army bear was released in 2019. The Women's Land Army (WLA) was a British civilian group created during World War II to replace the men called up for the military. Over 80,000 women served working on farms, in sawmills, and in forestry. They became know as Land Girls and Lumber Jills. Please note the archive does not have a copy of this bear but is recorded here to complete the series.An example of the type of products sold along with Legacy Badges for fundraising in the 2010-2020s.Legacy bear dressed in a female WW2 Land Army uniform with a printed cardboard tag.Printed tag gives the price as $20.legacy appeal, fundraising, legacy bear

This item belonged to Alan Richardson, a sawmiller at Tabbara. He helped to build and held a ticket for the paddle steamer "Curlip". He was a member of the Rechabites from March 3 1892. The Independent Order of Rechabites began in Salford, England in 1835. It was named after Rechab, a leader in the Old Testament, who instructed his tribe to refrain from drinking alcohol. During the Industrial Revolution the idea of temperance became popular as damage was caused to families by alcohol. In Australia it was first established in Tasmania in the mid 1800s. In 1847 a branch was created in Victoria, and it then spread to other States. Members were provided with assistance during times of sickness, death and hardship. This item is associated with the Richardson family, early settlers in the Orbost district.A small grey book with a black spine. The title and details are in black print. Inside is a magazine cutting - "The Rechabite July 1st 1931". This book is the "Constitution of the Victorian District, No 82" and contains the district by-laws."This is to certify that Bro. A.J. Richardson was admitted clearance a member of the Orbost.........."richardson-alan rechabites

John Lundy-Clarke grew up in the Kalorama/Mt Dandenong area and later in life (1972-74) began to write a comprehensive history of the area working from an original settlement map in an effort to cover all areas. William Lucas , who came from England to visit Matthew Child in the late 1870s. He purchased land from Matthew and married his daughter Catherine. They developed their property as the sporting lodge 'Glenrivers'. Their daughter Dorothea was born in 1888. She was an accomplished horsewoman who married her cousin Charles Percival (Percy) Child in 1917. Percy worked a sawmill on the creek .Black and white copy of studio portrait of Doris (Dorothea) Child (nee Lucas).Handwritten by John Lundy-Clarke on reverse: Doris Lucas “Dorothea?” Daughter of W Lucas and Catherine nee Child. Wife of Percy Child. Mother of Lois. Born 1889 died 1936 (?)dorothea lucas, dorothea child, percy child, matthew child, william lucas, catherine child

Two catalogues of goods to sell, from Ringwood Timber & TradingEditorial of 15201b includes a short history of the company. In 1937, Mr S Coopersmith and son, Frank (the present Managing Director) started a fruit case manufacturing business in North Melbourne under the name of The Cooper Case Co. The business flourished, and in 1940, recognising the possibilities in and around Ringwood, an old bush sawmill and an area of land on the Maroondah Highway, were secured. Subsequent purchases have since increased this area to approximately 15 acres. It was decided to widen the activities and scope of the business and two new firms were formed. Cooper Sawmilling Co., which operated a modern sawmill, and Ringwood Timber & Trading Co., which handled the output of the sawmill and introduced builders' and general hardware lines to meet the demands of this rapidly expanding area. As Ringwood grew, so too did the organisation which was created to serve it. The principals studied timber and hardware merchandising trends overseas, and after considerable investigation the new building on Maroondah Highway was completed in 1956. Today, acclaimed as one of the most modern mills and hardware stores in the Southern Hemisphere, combining up to date machinery and handling equipment together with unique drive-in facilities and a self-selection centre. Ringwood Timber & Trading Co. are proud to offer a service unparallelled to home builders. In conformity with modern commercial practice the various firms have since been incorporated under the Victorian Companies Act and the latest accounting methods and office equipment have been installed to provide an efficient and virile administration to control the entire manufacturing and trading activities. We have a staff of over 220 personnel, each trained in their particular field to provide you, our valued client, with expert advice, quality merchandise and second-to-none service to enable you to fulfil every need in and around your home.

Research by O.D.H.S. suggests that the 'Oliver' who received this wallet from 'John' is likely Oliver George Scott but the identity of 'Jack' or 'John' is unknown. Oliver G Scott was born 19/2/1880, enlisted 13/9/15 after examination by Dr Kerr of Orbost, returned 7/5/19, died 3/8/1920, buried in Bairnsdale. His name is on the Orbost Roll of Honour. He was one of four Scott brothers who enlisted with three of the four dying in action. The Scott family lived at Ensay. A fifth son John was not accepted on medical grounds. Prior to enlisting, Oliver is described as a sawmiller and a single man. This is a personal item with high significance because it was owned by a man who enlisted from Orbost for World War I. It was a gift from one soldier to a mate during World War I and has personal inscriptions.A square black leather card wallet with metal binding and clip. It has two flat leather pouches inside.In pen - "From John to Oliver for birthday 18.2.18. Salisbury Road Fovant England Jack killed 4.4.18wallet

P. S. Adelaide was a logging steamer operating between Echuca and Barmah forest. It was built in 1866 by G. Linklater, Echuca. Original owner J. G. Grassie, Poon Boon Station & S. H. Officer, Murray Downs Station. In June 1891 she was purchased by Murray River Sawmills and spent most of her working life on the Barmah Forest run. In 1960 she was purchased by Echuca Apex Club and steamed to Echuca. Installed on a bed of cement in Hopwood Gardens, Echuca before being restored to be refloated as a significant addition to the Port of Echuca maritime fleet (Parsons, R. Ships of the Inland Rivers. 2005. p.46)The P.S Adelaide is extremely significant as it it the oldest known wooden hulled paddle steamer in the world. She was built in Echuca in 1866 and still operates on the Murray River today. She has worked in the Wool Industry, the Timber Industry and the Tourist Industry.Colour (hand painted?) postcard and colour negative f P. S. Adelaide towing an outrigger barge. Three men can be seen on the lower deck and one on the top deck.on the front of the postcard:". Log barge & steamer Echuca" On the bow of the steamer: "Adelaide". On reverse of postcard, in blue pen:" PORT 16.3.82 COL NEG 13x18x1." In black pen encased in a square:"396.1" In blue fountain pen. Letter addressed to "Mrs. J. Robertson 37 Roxburgh St. Ascot Vale." " Your letter to hand(?) Sat. I am much better since my trip away. Was sorry to hear Jess(?) was not well. Hope she is better again. Hoping all are well. Love to all H." Postcard stamped: "Echuca Victoria Ap 6 08" Printed in green "Post W.T.P. Card". In has a red one penny postage stamp in top right hand corner.p. s. adelaide, echuca, port of (riverboats), echuca - history, post cards, echuca, paddle steamers, timber barges

Rail tractors were popular with Victorian sawmillers. They were generally cheaper than a steam locomotive, required no special qualifications to drive, and used proven power plants for which spares were available locally. The tractor was constructed by Day’s Engineering of South Melbourne which, although better known for its pumping equipment, built more than fifty rail tractors for Victorian sawmillers and other industrial tramway users. W. Day & Sons is believed to have constructed its first light railway locomotive in 1926. From then until the mid 1940s, the firm appears to have built at least fifty locomotives at its premises in South Melbourne, of which roughly half were four-wheel locomotives and roughly half were six-wheel locomotives like the restored Day’s rail tractor formerly operated by Ruoak Timbers. Of the four-wheel locomotives, ten were 2-ft (610mm) gauge locomotives similar to this one. Today, only two survive, a complete example at the Puffing Billy Railway Museum at Menzies Creek, and one at Alexandra Timber Tramway Museum This 2-ft gauge 4wPM locomotive is believed to have been one of two Day's Petrol Rail tractors formerly used by Cheetham Salt, possibly at the Moolap works near Geelong. Service History :owned by Cheetham Salt, Moolap ( dates unknown ) Geelong Steam Preservation Society , Belmont 1973 ? Puffing Billy Steam Museum , Menzies Creek Historic - Industrial Narrow gauge Railway - Rail Tractor used by Cheetham Salt Company works at Laverton, Moolap and Geelong, Victoria , Australia Petrol Rail Tractor made of Iron , wrought iron, steel puffing billy, industrial narrow gauge railway, rail tractor, days engineering, cheetham salt,, petrol rail tractor

Hardcover. Green dust cover. Front cover photograph is Krauss 0-4-OWT, builder's No. 2459 of 1891, takes water at the western end of Rubicon Lane in 1934. Driver Bob Rees attends to his engine while brakeman Hayden looks on. End papers show a photograph of a man standing besides a timber railway trolley holding onto the brake lever. There is a group of men, some sitting and some standing, on piles of cut timber under a large, open shed in the background. There are also some small, timber, tent like structures standing next to the railway tracks. There is a forest in the far background. Written in white is the line "Mr Clarke & Kidd's Sawmill". non-fictionrubicon, timber, sawmill, railway, tramway, clarke and pearce, evans, peter, marysville, krause, forest, mountain

A history of the Rubicon forestHardcover. Green dust cover. Front cover photograph is Krauss 0-4-OWT, builder's No. 2459 of 1891, takes water at the western end of Rubicon Lane in 1934. Driver Bob Rees attends to his engine while brakeman Hayden looks on. End papers show a photograph of a man standing besides a timber railway trolley holding onto the brake lever. There is a group of men, some sitting and some standing, on piles of cut timber under a large, open shed in the background. There are also some small, timber, tent like structures standing next to the railway tracks. There is a forest in the far background. Written in white is the line "Mr Clarke & Kidd's Sawmill".Stamp of the Marysville & District Historical Society Inc / PO Box 22 / Marysville 3779 Signed by the author, Peter Evansrubicon, timber, sawmill, railway, tramway, clarke and pearce, evans, peter

Ruth Woodward was the daughter of Alan Richardson a sawmiller at Tabbara. Richardson Helped build and held ticket for paddle steamer "Curlip". Crochet covers for milk jugs, teacups and bowls were produced to repel the dreaded Australian blow fly. They were typically decorated with Australian flora and fauna and commemorative motifs and sometimes edged with beads, shells and other three dimensional forms, not only for appearance, but also to weigh down the crochet so it would stay safely in place on the jug. The three dimensional parts were stiffened with sugar syrup, or sometimes starch, paraffin or gelatine. The main sources for crochet cover and other needlework designs available to women were in journals, magazines and pattern books. This item is an example of a handcrafted item and reflects the needlework skills of women in the families of the early settlers.Small handmade star-shaped milk cover with a white tulle centre and beading coming down to points off the centre. Beads are clear and black.milk-cover handcrafts needlework beading richardson

The P.S. Curlip was built by Samuel Richardson & Sons at a Tabbara sawmill in 1889. Alan Richardson, shown in the photograph, was the captain. It was operated along the Snowy River in Australia's Gippsland region between 1890 and 1919, before being washed out to sea, and broken on Marlo beach, by a flash flood in 1919. James Winchester was born in Geelong in 1856. He first sailed into Marlo, aged 15 and returned in the 1870's. he worked on the snagging punt on the Snowy River and also on the Paddle Steamer Curlip which towed the barges to collect the maize grown along the Snowy River. Wooden chutes were constructed along the river banks to load bagged maize onto the barges. The bags of maize were sent down the chutes into the waiting barges. This is a pictorial record of the iconic Paddle Steamer Curlip which has a significant association with Orbost. It records the method of loading maize onto barges through a wooden cchute.A large framed black / white photograph of the Paddle Steamer Curlip and a barge on a river. The barge is being loaded with maize through a large chute. In the background is the Snowy River bridge. the frame is wood. There is also a copy.on back of copy - " Jim Winchester, Alan & Frank Richardson, Curlip - barge & chute for loading maize"p.s.-curlip transport-shipping richardson winchester-james snowy-river maize-loading

The barge 'Ada' was built in Echuca in 1899. It was 33 metres in length and 6.9 metres wide and was made from timber and iron. It's design was unique as it was half-timber, and half-iron- the iron featured above the water line to prevent the wool bales from getting wet. The 'Ada' was used to carry wool from sheep stations on the Murray and Murrumbidgee Rivers down to Echuca Wharf for distribution around the world. The Permewan Wright, Murray Shipping Company, owned the 'Ada' and in the1930s the barge was sold to the Evans family who used it to transport timber to it's Echuca sawmill. The 'Ada' was purchased by the Port of Echuca in 1974 and is seen here on the Moama slipway undergoing restoration for Port of Echuca in 1979 to 1980. The remains of the 'Ada' still lie on the banks of the Moama slipway but it has fallen into near complete disrepair.The barge 'Ada' is very significant due to the uniqueness of her design. The hull is timber, up to the water line, then iron from the water line up to protect the bales of wool bales that it transports from water damage. The P.S Pevensey, within the Port of Echuca collection, has the same design feature.The barge 'Ada' in dry dock, on a slipway with a 4 knot marine sign is next to it. The barge is surrounded by trees and has since fallen into disrepair. Verso: 'Ada Barge'murrumbidgee river, wool, ada, murray river, barges, evans saw mills, timber industry, port of echuca, echuca wharf, permewan wright co.

James came to Australia from Plymouth on the ship "Mobile" arriving 16/11/1853 aged 22. he married Alice Roberts on November 27, 1861. With a large young family he moved from Central Victoria to Glengarry in Gippsland where he farmed and set up sawmills at Glengarry and Rosedale. After hearing of land grants at Orbost and investigating the possibilities with Elizabeth, his eldest daughter he selected land at Pumpkin Point, Bete Bolong. The whole family (ten children from 23years - 2years) eventually moved to Orbost around 1885. ( read "From White Knowle to Pumpkin Point" by Hon Peter Nixon A.O.) He had the first saw mill. He convened the meeting that established butter factory foundation and shares and was the first Agricultural Show president,James Nixon was a significant and influential citizen of Orbost's early years.Portrait done in oils of Nixon, James Mr. The portrait is of the bust of Nixon in a tuxedo with blue to grey background. Timber finish frame.nixon-james orbost-bete-bolong pumpkin-point

Bogong Village, which was known as “The Junction”, is well recorded. The first tent camp was at the junction of Pretty Valley and Rocky Valley streams in the early 40’s. Further downstream were the sawmill, stables and blacksmith’s forge. Horses were the main mode of transport in the early days. The road to Bogong had reached the lookout spur just beyond Roper’s Spur track just before the 1939 fires. The early forties saw rapid growth of the village, with single and married men’s quarters, workshops, mess huts and administrative offices. The facilities necessary for communal living were quickly in place- a post office, police station, co-op store, medical centre, community hall/theatre, tennis courts and school. Much of the temporary accommodation that housed groups such as the Albion Quarrying Company were in the area now under water.This group of photographs are a pictorial record of the early history of the Kiewa Hydro Scheme, the people who worked in the background supplying administrative support and the workers and their families. It also shows a glimpse into how a large group of people from very diverse backgrounds came together to enjoy social activities and share each others companyGroup of 10 black and white photographs and photocopies of original photographs of varying sizes (some official SECV photos) Some Photos are labelled with the date and the names of SECV staff members. Depicting early life at Bogong Village 1. Group photo – Kiewa House Residents 1.8.41 (SECV official photo) 2. Female staff residents 3. Female office staff 4. Kitchen staff – Junction Mess (SECV official photo) 5. Male administration staff Bogong 6. Bogong Social Club fancy dress ball, 1940 7. Wives and children of SECV workers 8. Children in fancy dress 9. Opening of Volunteer Air Observers post 1943 10. Flag raising at opening of Volunteer Air Observers post 1. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 1.8.41 Time: 12.30pm No:K 435 Kiewa Hydro-Electric Works. Kiewa House Residents Back Row L to R: S.A. Salmon, W. Strachn, T.A Connors, W.J Norman, R.C Grealey, R.D Hegarty, Mrs Hegarty, W.R Morgan, S.A Clarke, P. Morgan, P.J. Harnetty, G.W Crouch. Front Row L to R: W.L Godfrey, R.S Hollands, Pte. R Charlesworth, R.L Dunn, N Caldwell, L.T Davies, I Webber, H.L Kendall, P Tiller, Ricky Hegarty, L.T Guy, M.C Cox, K.F Calder, D.S Gibson 2. Printed on bottom: Staff who lived at Kiewa House and worked in the Administration Office c 1943 Handwritten at bottom Priscilla Johnson (nee Reid) At top of page A GOOD LIFE: WOMEN’S RECOLLECTIONS OF LIFE IN THE UPPER KIEWA VALLEY 3. Printed under photo- Office Staff – Bogong 4. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 18.5.40 Time: 11.05am No:K 103. Kiewa Hydro-Electric Works. Kitchen Staff- Junction Mess. Opening night of the new staff mess Bogong. 5. Printed under photo -Administration staff Bogong 6. Printed under photo- The social club raised money for patriotic fund from fancy dress nights. (1st Fancy Dress Ball, Bogong 1940) 7. Printed above photo: ---- and family life begins (1942 Bogong) 8. Printed under photo: A favourite photograph 9. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 24.5.43 Time: 2.8pm No:K 1151 Kiewa Hydro-Electric Works. Bogong- Squadron Leader Leggett speaking at opening of Air Observer’s Post 10. Printed under photo: Raising the flag at the opening of the Volunteer Air Observer’s Post at Bogong - 1943 bogong village; kiewa hydro electric scheme; social activities; community clubs

Bogong Village, which was known as “The Junction”, is well recorded. The first tent camp was at the junction of Pretty Valley and Rocky Valley streams in the early 40’s. Further downstream were the sawmill, stables and blacksmith’s forge. Horses were the main mode of transport in the early days. The road to Bogong had reached the lookout spur just beyond Roper’s Spur track just before the 1939 fires. The early forties saw rapid growth of the village, with single and married men’s quarters, workshops, mess huts and administrative offices. The facilities necessary for communal living were quickly in place- a post office, police station, co-op store, medical centre, community hall/theatre, tennis courts and school. Much of the temporary accommodation that housed groups such as the Albion Quarrying Company were in the area now under water.Pictorial history of the early years of Bogong Village including one photo taken following the devastating fires of 1939. Photos show the terrain in which Bogong Village was built, the early construction used for the temporary buildings and the housing and the amount of infrastructure required to accommodate the needs of the residents of the area including workers, their families and other support staff. Set of 9 black and white photographs and photocopies of photographs depicting early buildings at Bogong Village . Photos show very early construction buildings as well as the village in various weather conditions, including snowing and after bush fires. (some official SECV photographs) 1. Bogong Village in heavy snow 2. Bogong Township during heavy snow (SECV Official Photo) 3. VIP Lodge at Bogong in the snow 4. Bogong Village - circa 1940’s 5. Bogong Village under street lights 6. Lewis Construction Camp (SECV Official Photo) 7. Albion Quarrying Co. Camp (SECV Official Photo) 8. Tent camp and early buildings following 1939 fires 9. Typical house – Bogong Village 1. Handwritten under photo – August 1948 2. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 25.8.48 Time: 9am No:K 4680 Kiewa Hydro-Electric Works. Bogong Township 3. Handwritten on back of photo- V.I.P. Lodge, Bogong 4 – 5. No markings 6. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 28.11.40 Time: 1.40pm No:K284 Kiewa Hydro-Electric Works. Lewis Construction Camp 7. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 11.1.41 Time: 10.40am No:K294 Kiewa Hydro-Electric Works. Albion Quarrying Co. Camp – Bogong. Handwritten on back of photo: On the floor of the present dam 8. No markings 9. Printed under photo: STATE ELECTRICITY COMMISSION OF VICTORIA Date: 11.1.46 Time: 1.23pm No:K2181 Kiewa Hydro-Electric Works. Bogong – Typical House bogong village; 1939 fires; kiewa hydro electric scheme;

The American Truck History Association is an international organization, with over 21,000 members in the United States, Australia, Canada, and 20 other countries worldwide. A.H. McMullen & Co P/L, established by Arthur McMillan in February, 1951, had a long history as transport operators in Orbost and Gippsland districts. The company became Gippsland's largest transport company. It carted timber from the Orbost/ Cann River district district sawmills to the railway station. Two trains a day left the sloaded with timber. Beans were carted from Fisher's Bean Factory to Melbourne and Sydney. Cream from the farms was transported to the butter factory and for almost twenty years Fuel was carted from Melbourne to the RAAF base at Sale by McMullens. In 1970 the company was sold to F.J. Stephens and then to Mayne Nickless Transport. (ref.Deborah Hall "In Times Gone By') A.H. McMullen was a significant business in the mid 20th century in Orbost. This book is a useful reference source.A 40pp book with a dark blue cover titled "The Gearchange". It is a "Classic Edition Issue No. 2" and features A.H. McMullan & C0 P/L. It has a cost of $20.00. It contains illustrations, photographs and text.transport mcmullen-transport-orbost trucking

Snowy River Shipping Company formed in 1880. They were soon shipping produce (mainly vegetables) from the area to Melbourne. The Snowy River Shipping Company was formed by Mr Henry James during the 1880s, with Captain McNeil as master. Captain Hegarty was the shipping agent at Marlo. Towing a line of small barges these paddle steamers plied their trade between the port of Marlo, and the farms along the river banks, churning their way almost twenty miles upstream to a landing beside what is now Frank Richardson’s property. On these trips, the barges carried mail and supplies to the townspeople and farmers, loading their produce, mostly maize, on the return trip to the coast. The coming of the railway in 1915 spelt the end for the little river boats. ( ref. F. W. RODWELL in the “Snowy Review”) Frank Richardson 1877-1950 was a sawmiller at Tabbara and helped build and run paddle steamer "Curlip"as engineer.This item is associated with an early transport business of the local district. The Snowy River once had its own paddle steamers. This item is reminiscent of that time.A light blue and white blank cheque for the Snowy River Shipping Company. The cheque is for The National Bank of Australasia and is numbered 01,491 in bold black print. It has a one penny stamp duty imprint.snowy-river-shipping-company james-harry

Two red covered auction catalogues for an auction on account of the State Rivers & Water Supply Commission on the 22nd to 25th November, 1954 (inclusive) held at the Big Eildon Project, Eildon, Victoria. Lots sold include Machinery, plant, stores and equipment, Saw Milling Plant, corr. Iron and timber buildings, 5 timber residences, 73 partly completed weatherboard 4 roomed flats, extensive collection of plumbers equipment, building materials, mess equipment, sawn timber, scrap, tools, kitchen and bathroom fittings, electrical equipment and costly spares and accessories. Catalogue has a Locality Plan of Eildon, photo, locality and description of the Eildon Sawmill. Photos of completed houses, incomplete flats and plan showing layout of flat unit, photo of flat block (Completed). Also Building Kits - Designs and Component Lists.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - big eildon project, state rivers & water supply commission, j h curnow & son pty ltd, eildon sawmill, prahran telegraph printing co

The settlement of Cabbage Tree Creek is located on the Princes Highway, 27 km east of Orbost in East Gippsland. The creek, which flows through undulating forest, takes its name from the patches of Cabbage Fan palms growing along its course. A school commenced classes in 1913, but enrolment was small and at times the school operated part time with several other small schools in the area. The school building served as a hall for the district. About 1946 two sawmills commenced operations at Cabbage Tree Creek, and the Forests Commission ranger was stationed in the area. The increased population allowed the school to have more teachers and make improvements. In 1953, a new prefabricated building was erected on a new site. However, by the 1970s employment in the timber industry was unstable and the population decreased. By 1974 the school again had only one teacher and eventually closed in 1993 to amalgamate with the Orbost primary School in Ruskin Street, Orbost. (Ref. VictorianPlaces)The school bell is a signal that tells a school's students when it is time to go to class in the morning and when it is time to change classes during the day as well as when students are dismissed from school. In most schools today it will be a tone, siren, electronic bell sound, a series of chimes, or music played over an intercom but often still called "the school bell". This item reflects the history of Cabbage Tree Creek as well as the technological changes in the school system.Brass bell with incised double lines on bottom edge and top near handle, featuring descriptive notation on front face. Bell has long wooden handle shaped and incised with four lines at base before brass housing with singular screw holding handle in place. Object is showing signs of wear, with blackened handle and patches of green oxidisation.SCHOOL BELL / SS No 3812 / CABBAGE TREE CREEK / PRIMARY SCHOOL / 1913-1993 / FORMALLY INCORPORATED / INTO / ORBOST / PRIMARY SCHOOL / 1994cabbage tree, east gippsland, cabbage tree creek, cabbage tree creek primary school, orbost primary school, school bells