Khaki painted metal casing with space for battery. Carry handle on top with on & off switch also on top. Front has globe & reflector with glass front and blackout cover which can be lowered over light. A belt clip is attached to back of lamp.Stamped on belt clip D↑ most wording unreadable ----No-------Thorne - 44lamp, army equipment

Colour photographs of the Stained Glass Window at the Ballarat Technical Art School, A division of the Ballarat School of Mines.stained glass, ballarat technical art school., miner's lamp

Arthur E. Woodley donated the WW1 Military Carbide Signal and General Purpose Lamp to Frankston RSL. It was given to Arthur E. Woodley of Crib Point during the 1960s by Captain Ivan E. Layton MBE who was then the Executive Officer of Melbourne Legacy. During WW2 Ivan Layton was secretary to General Blamey. Ivan Layton died on 15th September, 1979. The carbide workings of the lamp were removed because of corrosion, otherwise it is almost complete.WW1 Military Carbide Signal and General Purpose Lamp which is round and made of brass. The lamp has a latched and hinged brass top. Brass and wood hinged handle with knurled access knob which is situated at the top of the lamp. In between the handle uprights is a round chimney flu which allows heat to escape. Approximately one third down from the top of the lamp there is a brass side handle. Immediately to the left of the handle is a rectangular curved view port with brass cover. Directly opposite the side handle is a convex glass window. Air vents are located at the bottom of the lamp. Inside the top half of the lamp is a chamber which contains the carbide lamp and perpendicular sleeves for the insertion of coloured glass panels. The bottom half of the lamp contains the carbide.Manufacturers Stamp, 'PLAYER & MITCHELL LTD', 'SENTINEL WORKS' 'BIRMINGHAM'ww1, military, brass, lamp, world war 1, round, great war, carbide, signal lamp, player mitchell, birmingham

Starboard side light with fresnal glass lens with removable blue/green filter, oil/kero burner with reflector inside. Made by "Tung Woo Hong Kong No. S1477", rounded front and 2 flat sides, bracket on one side for hanging. H 57.5cm x D 35cm.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, starboard side light

Lamp, grey colour metal round with red inner glass. Moveable handle & hinged lid. Outer clear glass surrounds lantern & is intact. Meteorite' Model #92277flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Dark blue printed instructions on paper mounted on a buff coloured cardboard card.LAMPS, SIGNALLING DAYLIGHT, SHORT RANGE Lamp can be used either (1) on the spike and spike extension stuck in the ground or (2) in the hand if necessary, or (3) withe the adaptor provided on a standard helio stand. SIGHTING TUBE: It is important to see that the lamp is so aligned that the distant receiving station is at the centre of the cross slots and maintained in that position the whole time that signals are being sent. BULBS: when fitting a new bulb, insert the locating tongue on the washer to the front and push the stem right back in the slot. BATTERIES: The correct replacment unit for this set is 8 "S" cells connected "in series". Screw up both terminal nuts tightly, ans see thar all connectors are in position. NIGHT SIGNALLING: An adjustable screen is supplied for reducing the light and one of the colour discs should always be used in conjunction with it when signalling at night under enemy observation. KEY CONNECTIONS. Use the two-pin plug in No.1 socket as long as the light is good enough, then cahnge to No.2. This will greatly lengthen the life of bulb. Used bulbs and batteries should not be relaced in the box, but discarded and a fresh supply obtained. Get a copy of detailed instructions "How to Use" this signalling outfit. KEEP LENS, MIRROR, BULB AND FRONT GLASS CLEAN.instructions, lamp, signalling, daylight, short range

Part of Graham Collection, donated by the Family of Misses Mary and Edith Maude Graham, of 4 Blair Street, Portland.Glass centre for lamp. Long cylindrical tube, larger at base than at top.Front: 6 / Sun Brand / Best Crystal / Fireproof / Made in Czecho-slovakia (etched logo, base).

Displayed at History HouseSheet-metal lantern with cubed lantern mounted on cylindrical handle. Two sides are full-pane thick bevelled glass, one tin with concave reflector panel on inside and one side with hinged door with red glass circle mounted in the middle. Painted black with black chimney and hood. Brass edging to glass panes.Front: Goodwin & Co/Birmingham (metal embossed plaque, candle mount).port of portland archives

Sheet tin, glass and copper carriage lantern with glass front and red bull's-eye back. Mounted on cyclindrical handle. Round framed glass is hinged with copper hood. Painted black.Front: Brandy Bros Co/Manufacturer/422/Elizabeth St/Melbourne (embossed brass plate, wick base)

A flat-wick lamp is a simple type of kerosene lamp, which burns kerosene drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat," or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light which is brighter than that produced by an open flame. The lamp burner has a flat wick, usually made of cotton. The lower part of the wick dips into the fount and absorbs the kerosene; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick, and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a toothed, metal sprocket bearing against the wick. A paraffin lamp with a green metal base to hold fuel with a side screw to adjust wick length. An opaque white glass shield sits in a metal frame attached to base* moorabbin, bentleigh, cheltenham, pioneers, early settlers, market gardeners, lights, lamps, paraffin, oil lamps

This particular lamp was made for the dinner table or "parlour". This was the most effective indoor lighting before electrical lighting was introduced in the 1940's. These table lights would have still been used after this time as emergency lighting during electrical power shortages (outages). These emergency lighting lamps, including candles, were eventually replaced by battery power. The Kiewa Valley was supplied by electricity well before many other rural regions due to the State Electricity Commission constructing the Kiewa Hydro Electricity power turbines (late 1930's to mid 1950's). Petrol and diesel generators were used in other rural regions before state wide electricity was available.The significance of this kerosene lamp to the Kiewa Valley is that it provides the proof that before the Hydro electricity scheme was established in the valley, householder and commerce relied on candle/kerosene power. Although at certain times before battery and solar energy became the night time lighters the sole source of lighting was candle power and kerosene power. The supply of both however was still required by most of the population by supply from city and larger country town suppliers. This nearly fully glass made table lamp(kerosene) has a large glass bowl/basin like kerosene storage unit with a glass circular finger handle (similar to a ordinary cup). Formed single star like patterns (50mm apart) encircle the centre of the bowl. On top of the bowl sits the metal (brass) wick holder with a small wheel protruding out one side for adjusting the wick length(increasing or decreasing the strength(regulating) of the amount of light projected. Four prongs rise from the circular base light fixture holding the windproof and refractive glass "pot belly" shield. lamp table, kerosene lamp, household lighting (non electrical)

The period when kerosene was extensively used for indoor lighting was before electrical reticulation was installed in rural areas. In remote areas this was up to the mid 1900's. The kerosene lantern however was still in use, for camping and outdoor activities, well beyond this period and was eventually replaced by LPG and battery powered lighting. The transition phase to "modern" outdoor and domestic lighting lingered on the rural areas where the electrical reticulation suffered from reliable constant supply.In the Kiewa Valley, being a rural region, had reliable electrical domestic and farm supply only after the Kiewa Hydro Electricity Scheme had been fully operational. The supply was relative to how close the homestead was to the major electricity substation. This kerosene lamp was in use during the period when it was the only reliable source of domestic night time lighting. The strength of refractive light produced by this lantern/lamp hinged upon the size of the lamp(wick and glass bowl). The small size of this lamp suggests that it was for use in a small room(children's bedroom) or as providing a light for a safe walk to the outside ablutions (toilet) area. This small kerosene lamp has an enclosed "cup" body which would have contained the kerosene fuel. The top wick holder, made from brass, has an extended enclosed spout which raises the wick approximately 20mm from the bottom of the holder. The wick holder screws into the the top of the kerosene reservoir bowl and has a wick adjustment screw (light control) at one side. The small white glass light reflector bulb nestles securely onto the wick holder and is kept snug by snap designed extending "fingers". The section between the bottom of the refractive glass "light" bowl and the top of the kerosene bowl has perforations to allow air passage to feed directly to the wick.The light refracting bulb is open at the top to allow heat and smoke from the burning wick to escape upwards.On the wick control screw "CWB BRITISH MADE"kerosene reading lamp, domestic lighting, bedside light

This transformer lamp system, which has a dial to transform 240 volts to a minimum of 32 volts was used by electrical technicians to inspect internal parts of the large generators (even in small confined spaces). The reason for the reduction of the 240 volts to the 32 volts was for the safety of the inspector. The SEC Victoria Hydro Scheme's electrical generators are powered by the hydro force of "stored" water at a higher altitude. The establishment of both the NSW and Victorian Hydro schemes was achieved from the mid 1900's to the 1960's. At this the point in time the need for additional power sources to quench both an industrial and domestic demand for electricity was purely an economic and not and environmental (carbon reduction) factor. This hydro scheme was instigated by "the Government of the day" as a bold move and was the major force of the World War II refugee and "technical" workforce inclusion of skilled and unskilled migration into the Australian environment. Although this mass "invasion" of workers with families was thought of in some circles as intrusive, the expansion of population post war years and its integration into the Australian rural sector, produced the multi- lingual multi-cultural diversity of later years.This transformer lamp is very significant to the Kiewa Valley as it was introduced as a very small part of the explosion of human resources into the valley. This influx of population transformed the region from that of a basically quiet rural region to one which evolved into both industrial and larger residential community. This evolution in the valley created a change, not only in the "physical" landscape but also the socio-economic expansion which permitted other "tourist" based industries into the valley. This is also a specific electronic item which was manufactured in Melbourne and not sourced from Europe or Asia. This demonstrates the fast evolution of Australian technology to a high standard compatible to that of the rest of the world.This heavy hand held electrical transformer (transforms 240 volts to 32 Volts) an has one leather handle on the top with three small (gauze filtered) air holes. It also has two 2 pin directional cable distribution (clipsal) in/out points 10amps / 240 volts. There is one glassed in volts/ac meter and one variable switch (180 to 150 voltage in settings of 10 volt increments.There are two vents (one on each of the smaller sides). There is also one three pin electrical lead coming out from the top.On one side is a manufacturer's plaque with "ELECTRONIC A & R EQUIPMENT MELBOURNE" and underneath "TYPE 1719, PRI V. 180 250" underneath "V.A. 1250" underneath "CYC 50" underneath "SEC V. 115" underneath "SEC A. 10 . 8". The label on topside "CAUTION SET SWITCH TO 250 v BEFORE CONNECTING TO MAINS THEN, WITH EQUIPMENT OPERATING, SET METER TO RED LINE.kiewa hydro electricity scheme, victorian state electricity commission, transformers

Blackout lantern used in WW11. This type of lantern was used during both World War. It is an artillery siege lamp and was originally used by artillery units. The lamps were powered by a single candle, the light being magnified by a lens. A shutter closes over the lens to give an illuminated vertical line. They were used originally in fortified siege artillery positions as a general purpose lamp. They were also used as aiming lamps when they were placed in front of artillery positions and used as a guide in aiming at night. These lamps were often used on the front of bicycles to guide at night. Donated by Clem Heather. Forestry Commision, carved faces on trees with axe., builder of tall. spliced single pole fire towers. This item is considered rare and important. It is historically and technically siginficant at a national level.Small black metal blackout lantern with handle. Front of lantern has round shield with small slit - small door at side for easy lighting of candle. It is hand held or placed on flat area, open base so candle can be inserted and 'screwed' in. Front is a magnifying glass and it has metal lens cover with vertical slit. lantern blackout ww11 military candle-power lamp

This item is an important example of the early technology of artificial light. It has historical significance in demonstrating lighting devices used before the widespread use of electricity.Kerosene/oil hand-held lantern with carry handle. Red glass window (for a show of red light) and a clear glass window that opens for lighting of wick. (Dietz Dainty Tail Lamp)lantern candle dietz-dainty-tail-lamp

This item is an example of a lighting device used before electricity and battery power were widespread.A small brass Elfin Reflector Night kerosene lantern with a reflector plate at the back. A handle runs around the middle. It has a small canvas wick. The glass is missing.On top of fuel tank-ELFIN REFLECTOR NIGHT LAMP On back-MADE IN U.S.A. BY EDWARD MILLER & CO USA On wicker winder (left) -E. MILLER -CO.U.S.A.lamp lantern kerosene oil lighting miller-edward

Richard Liebreich of Germany invented his design of ophthalmoscope in 1855. This example is complete in its case with Coccius lenses and condensing lenses. Early ophthalmoscopes required an external source of illumination, eg lamp or candle, and light was reflected into the eye to be examined by the mirror on the ophthalmoscope. The earliest versions of the Liebreich ophthalmoscope used a polished metal surface to reflect light; glass mirrors were introduced in 1870. A condensing lens was held in front of the patient to view the image. A Coccius lens could be clipped into the holder to counter ametropia of user or subject.This Liebreich ophthalmoscope is significant for the collection as it is the only complete example of the three held in the collection.Cased Liebreich ophthalmoscope with 5 small coccius glass lenses and 2 glass condensing lenses. Non-illuminated ophthalmoscope has concave mirror in round head with central sight hole.Hinged coccius clip attached to hold lenses. Black metal head, silver coloured mount and black turned timber handle. Case has black leather outer lining and purple velvet and satin inner linings. Case hinged with snap closure. On front of case:"LIEBREICH'S OPHTHALMOSCOPE" 4 of 5 Coccius lenses engraved with powers: "8-", "12-", "-01", "+01"ophthalmoscope, optometry, ophthalmology, liebreich, coccius, lenses, eye examination, fundus, funduscopy, non illuminated, instrument, eye doctor, liebreich ophthalmoscope

This item is an example of a lighting device commonly used before electricity was widely available for domestic use.A hurricane lamp with a rounded tank and small carry handle (a larger handle is possibly missing). It has a lever to open the glass tank. It has a metal base which is filled with kerosene. On top is a metal hood with vents.Around base : Chinese characters. On top : "Made in China KWANG HWA"lighting lantern kerosene-lamp hurricane -lamp

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. This lamp appears to be a modern reproduction of an earlier optional wall-mounted kerosene lamp. The lamp has been produced as an example of a 19th and early 20th-century marine kerosene navigation lamp. Marine lamp; portside metal kerosene lamp with two flat sides, and a curved front. The front has a red ridged glass lens insert and the name "port" is inscribed on a fixed brass plaque. A round chimney is on top of the lid and it has a catch. The fuel tank and wick can be removed through the base. The metal appears to be electroplated.Inscribed on the plaque; "PORT"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, lamp, ship lamp, port lamp, marine lamp, navigation lamp, port, lantern, kerosene lamp, marine technology, ship light, portable lamp

One of the most common centre draft kerosene lamps one can find in the USA and Canada is the Rayo. Large and sturdy, simple to use, but also notorious for being a fuel hog. This lamp was made by Bradley and Hubbard Metalworks in Chicago also Bradley and Hubbard made the “Perfection” brand lamps that look like the Rayo and are pretty much the same lamp with all parts interchangeable. The Rayo was given away to customers for free as a promotional item by the Standard Oil Company. The lamp’s huge appetite for fuel meant a hefty increase in sales of kerosene for the company and increased profits. The Rayo is a classic centre draft lamp that uses a widely available tubular wick that measures 62mm flat. It employs a simple and reliable mechanism for securing wicks in the burner along with a brass tube with many small teeth at its end. The tube is attached to the toothed rack that’s moved up and down by the adjuster knob.This type of lamp was used in most households and on rural properties before the introduction of electricity and is an early example of a promotional. The lamp was given away to customers of Kerosene oil as a means of increasing the Standard Oil Company sales of Kerosene during the late19th to early 20th century.Lamp of metal without shade. Mantle burner, plated light metal base. Ornate shade holder. Broken glass.Marked "Rayo Junior"flagstaff hill, warrnambool, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, mantle lamp, metal lamp, lighting, oil lamp, bradley & hubbard

Metal grey round lantern, rope attached to top, clear glass is crackedflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village