The steam engine indicator, or dynamometer, is an instrument used on a steam engine (such as that of a vessel or train) to measure and record the change in the pressures of the engine’s cylinders during their operating cycle. The engineer would use it to identify problems or defects such as bad valve settings or constricted steam pipes. It could indicate the difference in efficiency caused by adjustments made to the engine, being able to instantly measure the variation of pressure from the engine stroke at any given time. This force of power would be registered by a pencil, fitted to the adjustable arm, which would trace a line on paper wound around the cylinder. The recorded information could be used in conjunction with mathematical tables. This particular instrument was made by T.S. Mc Innes, one of the better manufacturers of engine indicators. Mc Innes engine indicators were still being used in the mid 1900’s. This specific instrument was used by Mark Forsythe of North Berwial, Scotland and late of Ararat, Victoria when he was chief engineer on the “SS Talawena” in 1892. The Port of Warrnambool, in Victoria, harboured steam ships that carried both passengers and cargo along the south west coast in the late 1800’s and into the 1900’s. The engineer of a steam ship was responsible for reaching and maintaining the optimum level of steam energy to serve the locomotion and efficiency of the steam ship. The engineer would use a steam engine indicator to measure and record information to achieve this purpose. Engine Dynamometer or Steam Engine Indicator in square, fitted oak case. This brass instrument is used to measure and record steam pressure for setting up and adjusting valves on a steam engine. It has an oscillating recording drum with vertical, silver clip attached for holding paper in place around the drum. The drum oscillates left to right. There is a pulley attached to a length of cord, which is attached to the drum. Beside the drum is a fine metal arm, vertically adjustable, small hole in the end to hold a pencil. Inscription stamped into bracket of the arm. The engine indicator is mounted on a hinged side of the case that swings out ready for use. Attached chains prevent the side from opening past vertical. There is storage for other accessories and an empty compartment in the base (where a scale or ruler may have been located). The case has a collapsible wooden handle, brass hinges and two brass, hook-shaped catches. There is a code stamped inside the lid. It contains a brass, ‘T’ shaped steam-cock (or stop cock) with two open ends made of metal pipe with different sized threads. (Turning the handle on top opens and closes the space in the pipe and would close off the flow of steam from one end to the other.) Also inside the case are three different spiral springs, each with a threaded nut on the end that has a threaded hole inside it. Used by Mr Mark Forsythe when chief engineer on the SS Talawena in 1892 “T.S. MC INNES PATENT” and “522 _ _” (last 2 digits are unreadable) pressed into the arm of the brass indicator. “[ ] X ’ stamped inside the lid of the case. The 3 springs all have a number stamped into them: (1) “32” and “12” (2) “12” and “16” [above] “12” (3) “64” and “150” Card that came with instrument “This instrument was used by Mark Forsythe of North Berwial Scotland and late of Ararat, Victoria when chief engineer on the SS Talawena in 1892" dynamometer, steam engine indicator, t.s. mcinnes, glasgow, dobbie mcinnes, port of warrnambool, warrnambool, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, maritime museum, shipwreck coast, great ocean road

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples such as the subject item have no makers names.A vintage drilling tool that gives a snapshot into how holes were drilled by hand into small or delicate objects during the Victorian era. Tools from this time are today regarded as collectable items eagerly sought by collectors of antique tools. Archimedean drill with Rosewood hand, brass bearings, steel twist and wooden grip. Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill, archimedean drill with wooden hand, drilling tool

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples have no makers names.A vintage drilling tool that has been nickel plated with brass fitting and easier to sterilise. The item therefore could have been used in the medical profession as a bone drill during surgery. Weighted Archimedes drill all metal construction, nickel plated with brass handles centrifugal typeNoneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill, drill, tool, drilling tool

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples such as the subject item have no makers names.A vintage drilling tool that gives a snapshot into how holes were drilled by hand into small or delicate objects during the Victorian era. Tools from this time are today regarded as collectable items eagerly sought by collectors of antique tools.Archimedean drill with wooden grip and butterfly nut on chuck.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill, drill, fretwork tools, wood working tools

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples have no makers names.A vintage drilling tool, the item therefore could have been used in various industries or professions where precise drilling is required. Archimedean drill with Rosewood hand, brass grip and fittings Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill

A scythe is an agricultural hand tool for mowing grass or reaping crops. It was largely replaced by horse-drawn and then tractor machinery. A scythe consists of a wooden shaft and a long, curved blade is mounted at the lower end, perpendicular. Scythes always have the blade projecting from the left side when in use. Mowing is done by holding the handle , with the arms straight, the blade parallel to the ground and very close to it, and the body twisted to the right. The body is then twisted steadily to the left, moving the scythe blade along its length in a long arc from right to left, ending in front of the mower, thus depositing the cut grass to the left. Mowing proceeds with a steady rhythm, stopping at frequent intervals to sharpen the blade. The correct technique has a slicing action on the grass, cutting a narrow strip with each stroke Mowing grass is easier when it is damp, and so hay-making traditionally began at dawn and often stopped early, the heat of the day being spent raking and carting the hay cut on previous daysEarly settlers and market gardeners used these scythes as they established their farms in Moorabbin Shire c1880A large metal scythe with a wooden handle x 2early settlers, pioneers, market gardeners, moorabbin, bentleigh, brighton, cheltenham, tools, blacksmiths

Alan Marshall was an author of more than fifteen books, and lived much of his life in Eltham. He became a central figure in the area's arts community of writers, artists, sculptors, film makers, actors and musicians. He is shown stroking a book to his heart, perched on a crutch, which references his disability (contracted polio when he was young), and his status as one of Australia's most successful and loved authors. His most famous book, 'I Can Jump Puddles' is based on his life story and the obstacles he faced as a child in trying to overcome his disability. Marcus Skipper submitted the idea for the work to the first 'Art in Public Places' Awards in 1990. The selectors at the time recommended that the work would be more suitably placed near the Eltham Library. It was commissioned and installed for the new Eltham Library, which was designed by Greg Burgess in 1994. It was partially funded by the then Shire of Eltham's Art Development Fund (Eltham Arts Council) and the rest donated by the artist Marcus Skipper. This work has significance for its reference to two well known names associated with Eltham and its history. The sculpture is a realistic statue of the famous Australian author Alan Marshall who wrote "I Can Jump Puddles". He lived and worked in the Shire. The artist Marcus Skipper represents a highly recognised family of artists associated with Monsalvat. The sculpture 'Alan marshall' has been classified as of regional significance by the National Trust of Australia. A realistic depiction (almost life size) of Alan Marshall cast in bronze with green patination. Dressed in a jumper and slacks, Marshall is shown perched on a crutch, holding a book to his heart, gesturing to his audience to come and listen to his words. alan marshall, bronze, skipper, i can jump puddles, eltham library, novalist, ekphrasis2017, figure, public art

A colour certificate given to the winners of the 1900 Intercolonial Eight-Oared Race. Rowed on the BRISBANE RIVER, BRISBANE / 12th May, 1900 / BETWEEN THE COLONIES OF / NEW SOUTH WALES - QUEENSLAND -- / VICTORIA -- SOUTH AUSTRALIA -- / won by / VICTORIA / J. DONALD Stroke / T. DAVIES No. 7 / H.J. HUGHES …6 / A. HALL …5 / A. DAWSON …4 / J. COCKBILL ...3 / C. STAMPER ...2 / J. SUFFREN ...Bow / J. COUNIHAN Cox / J.M. MACFARLANE Honorary Coach / And this / CERTIFICATE / hereby affirms that / C. STAMPER / rowed No. 2 in / THE VICTORIAN CREW. / For Victorian Rowing Association / (Signature) President / (Signature) Hon. Secretary

This image of the Ballarat Rowing Club in 1947 records the placings of threw crews in the Barwon regatta at Geelong in 1947 and the Ballarat Regatta in 1947. It also records the first time a new rowing style, "Leg and Body Drive" was used in rowing on Lake Wendouree at Ballarat.Photograph has light from lens across right side. Reverse has ink inscription: "Ballarat Rowing Club Lightweight Maiden Four Ballarat and Barwon Regattas, 1947. L Wallis Bow, J Nolan (2) E. McLenehan (3), J Trainor Stroke, W Hancock. Cox. Coach - Ken Baird. First crew to introduce "Leg and Body Drive" style on 14 starters at Ballarat defeated by Banks Rowing Club by three feet / Eliminated by Footscray at Barwon who won final. Stamp to centre Kodak Enlarged Print.

Norman BAGGALEY (b1937- ) Born in Staffordshire, United Kingdom . Arrived Australia c1978 Norman Baggaley obtained a National Diploma of Design (Painting ) at Stroke on Trent College of Art, UK. His first Australian appointment was from 1978 to 1980 where he was Dean of the School of Arts at Ballarat College of Advanced Education. He spent the next two years as Dean of the Faculty of Art and Design at Prahran College of education. From 1982 until 1991 Baggaley was Professor of Visual Arts and Dean at Prahran CAE, before moving to the Victorian College of the Arts as Associate Professor and Dean of the School of Art at the University of Melbourne Victorian College of Art. Norman Baggaley was Head of School at Ballarat College of Advanced Education. He offered the work for donation with the Art Acquisition Committee commenting that "it was desirable that works from previous heads of School of the Arts be held by the College and that initially the painting could be located in the Art staff room for the first year then displayed else where on campus. This item is part of the Federation University Art Collection. The Art Collection features over 2000 works and was listed as a 'Ballarat Treasure' in 2007. An oil on canvas abstract work by Norman Baggaley Gift of the Artist, c1984art, artwork, baggaley, ballarat college of advanced education, norman baggaley, oil on canvas

The Ruyton Reporter (formerly known as Ruyton Reports) captures the essential Ruyton Girls' School experience for the broader school community. It has been produced since 1986.The record has strong historic significance as it pertains to one of the oldest girls' school in Victoria, Australia. Ruyton was founded in 1878 in the Bulleen Road, Kew, home of newly widowed Mrs Charlotte Anderson (now High Street South). Thus, the record can be used as a reference example for research into Victorian school history. It also gives insight into the types of activities and events undertaken at Ruyton Girls' School during the period of its production. The record's significance is further enhanced by its exceptionally well-documented provenance, having remained the property of Ruyton Girls' School since its production.Colour publication printed on paper with staple binding. 16 pages.Front Page: the reporter / Ruyton / autumn 1995 / PRINT POST / PP 341999 00026 / APPROVED / 12 Selbourne Road Kew / Telephone: 9819 2422 / Facsimile: 9818 4790 / R / RECTE ET FIDE LITER / Launch of the Henty Rowing Club: The Senior IV / Contents / VCE 1994 / Allegro Al Fresco / Medieval Fair / Interview with / the Premier / Photograph courtesy of "Images" Photography / Bow: Emma Anderson, Victoria Wile, Kate Kotzmann, Stroke: Katrina Walker, Cox: Kate McQuillen / STOP PRESS: Head Coach, Gina Douglas has now won 4 National Titles in Perth /ruyton girls' school, ruyton, school, students, newsletter, ruyton reports, ruyton news, kew, victoria, melbourne, girls school

Miss Leonora “Leo” Wray MBE Leonora “Leo” Wray (1886-1979) was a champion NSW golfer, regarded as the “mother” of Australian golf. She won state and national titles multiple times across three decades. The Leonora Wray Trophy is awarded to the No. 1 player in Australia in national stroke average. Regarding her golf game Leo remarked, “Never a chance thrown away, or a single shot played without a definite object.” She was said to be commanding in “stature and mien” – a raconteur with a deep, booming voice who inspired in young players “a mixture of fear and awe, respect and affection”. In 1909 she contracted typhoid fever and was unable to play for 10 years. She was awarded an MBE in 1968 for her services to golf and inducted into the Sport Australian Hall of Fame in 1985. Photographer notations on slide: "Miss Wray. Vic Women's Ch'ship B98" Description: Golfer Leonora Wray swings her driver. She is wearing a tiepin and cufflinks. . Research by project volunteer, Fiona Collyer: Leonora Wray AKA “Leo” was a champion NSW golfer who is regarded as the “Mother” of Australian women’s golf. She won the NSW State Championships (1906, 1907, 1908) and the Australian title (1907, 1908). In 1909 she contracted typhoid fever and was unable to play for 10 years. Leonora regained the national title in 1929 and the NSW Championship in 1930. She was the champion women’s player of the Australian club ten times between 1907 and 1938 and five times champion at the Royal Sydney Golf Club between 1924 and 1933. She competed in the Australian Women’s Golf Championship at Royal Melbourne against the British team in 1935. During WWII, Leonora worked for the ANZAC Buffet Ladies Auxiliary in Hyde Park, Sydney. Regarding her golf game, she remarked, “Never a chance thrown away, or a single shot played without a definite object.” Leo was said to be commanding in “stature and mien” – a raconteur with a deep, booming voice who inspired in young players “a mixture of fear and awe, respect and affection.” Her portrait by Henry Hanke is held by the Australian Golf Club. Women’s Golf NSW holds its annual Leonora Wray Scratch Teams event and the Leonora Wray Trophy is awarded to the No. 1 player in Australia in national stroke average. In 1968 she was awarded an MBE for her services to women’s golf. In 1985 Leo was inducted into the Sport Australia Hall of Fame.golf, women golfers, royal melbourne golf club

This is a copy of a photograph of the Ormond College Crew in 1931. The photograph shows Dr Ian Murphy in his youth as the Cox of the rowing team. The Cox was an important role that coached, steered, and ensured the safety of the crew.Dr Murphy was Emerald's first and much-loved GP. His work for the community over 34 years was of immense benefit. He was awarded the British Empire Medal in 1977 for his service to the health of the community. This photograph shows Dr Murphy in his youth as a part of a rowing team at a winning school.Black and white photograph of the Ormond College Crew, 1931.Printed above the photograph: "Ormond College Crew / Head of the River, 1931" Printed below the photograph: "C. E. Gardner (3), R. S. Hooper (4), E. C. H. Taylor, Esq. (Coach), C. S. Donald (2), G. G. Powell (Bow), / R. Officer (6), J. R. Adam (Stroke), I. S. McLeod-Murphy (Cox), J. R. A. Glenn (7), A. D. Matheson (5). / Ormond defeated Newman by 1 1/2 lengths (Heat). Ormond defeated Queens by three-quarters of a length (Final)." Printed on the bottom right of the frame: "THE SEARS STUDIO / ST KILDA"dr ian macleod murphy, spud murphy, doctor, emerald, 1960s

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw blade with wooden handle attached with wingnut.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture.Compass saw with wooden handle and metal blade. Small teeth. flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool, compass saw

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw with wooden handle broken and metal blade. Small teeth.Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool, compass saw

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone. The subject item at this time cannot be associated with an historical event, person or place, provenance is unknown, as the maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture around the mid to late 20th century.Wood hand saw with wooden handle attached to saw by 4 rivets. No blade markings Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, handsaw, wood saw, carpenders tools, cabinet makers tools, wood cutting

A saw is a tool consisting of a tough blade, wire, or chain with a hard-toothed edge. It is used to cut through material, very often wood, though sometimes metal or stone. The cut is made by placing the toothed edge against the material and moving it forcefully forth and less vigorously back or continuously forward. This force may be applied by hand, or powered by steam, water, electricity or other power sources. An abrasive saw has a powered circular blade designed to cut through metal or ceramic. In ancient Egypt, open (unframed) saws made of copper are documented as early as the Early Dynastic Period, circa 3,100–2,686 BC. Many copper saws were found in tombs dating to the 31st century BC. Models of saws have been found in many contexts throughout Egyptian history. As the saw developed, teeth were raked to cut only on the pull stroke and set with the teeth projecting only on one side, rather than in the modern fashion with an alternating set. Saws were also made of bronze and later iron. In the Iron Age, frame saws were developed holding the thin blades in tension. The earliest known sawmill is the Roman Hierapolis sawmill from the third century AD used for cutting stone.The subject item is believed to date from around the mid to late 20th century and is regarded as a modern item. The maker is unknown but the pattern or design and type of wood used indicate it is a tool of modern manufacture. Compass saw blade with wooden with open handle blade attached with wingnut lever at side to adjust long narrow blade Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood cutting, wood saw, cross cut saw, cabinet makers tools, wood working tools, tool

A hacksaw is a fine-toothed saw, originally and principally for cutting metal. They can also cut various other materials, such as plastic and wood; for example, plumbers and electricians often cut plastic pipe and plastic conduit with them. On hacksaws, as with most frame saws, the blade can be mounted with the teeth facing toward or away from the handle, resulting in cutting action on either the push or pull stroke. In normal use, cutting vertically downwards with work held in a bench vice, hacksaw blades should be set to be facing forwards. Joseph Marples & Son Pty Ltd Traditional Craftsmans Hand Tools made in Sheffield. The finest quality hand made tools, backed by over 170 years of manufacturing heritage. .In the 1840’s Joseph Marples was one of several ‘Marples’ (most of which were related) in Sheffield manufacturing joiners tools, such as brass inlaid rosewood & ebony braces, boxwood spokeshaves, beech planes, gauges and squares. The business has remained within the family to this date, and has been based in Sheffield since those early days. Although modern technology has been used in some instances, many of the traditions of manufacturing fine hand tools has remained the same using selected materials and hand finishing, indeed the same threads are used in the gauges as were used over 100 years ago. A steel hacksaw. 'Marples' with bladeMARPLEStools, woodwork, metalwork, carpentry, pioneers, market gardeners, early settlers, moorabbin, cheltenham, bentleigh, ormond, joseph marples & son pty ltd, sheffield , england,

Ruth Cornell is centre back surrounded by local school friends in 1902 after the presentation of medals in celebration of the birthday of Edward VII. Ruth was the daughter of Frank and Blanche Cornell. Frank Cornell was first listed in Surrey Hills in 1906 at (6) Lorne Parade. In 1908 the listing gives his occupation as a clerk. He was born in 1869 in Richmond, Victoria and died 15 April 1917 in Surrey Hills from a stroke. His wife Blanche Annie Parsons Cornell (nee Bracher) was born in 1869 in Hokitika, New Zealand; she died on 21 January 1940. Children were: Gilbert Frank Cornell (b1894, Hawthorn; d1908, at Frankston beach, an accidental drowning) Ruth Amelia Cornell (b 1899, Kew; d 29 May 1977, Kew) Lorna Amy Cornell (b 1906, Surrey Hills; d unknown) Patience Blanche Cornell (b1907, Surrey Hills; d unknown). Ruth Amelia married David Ellis, c1922 in Surrey Hills. David was a dentist who practised in Surrey Hills for many years. Patience (Pat) Blanche married Norman Henry Brewer (1893–1975) in 1931 in Surrey Hills. Dr David Ellis' surgery was in Whitehorse Road in 1930s and later at the corner of Windsor Crescent and Union Road. The donor was Ruth's sister. A black and white photograph of eight girls dressed up and proudly wearing medals and flags. Most are wearing hats and holding a bottle of drink.lorne parade, surrey hills, king's birthday, edward vii, festivals and celebrations, 1902, clothing and dress, (miss) ruth cornell, (dr) david ellis, (mrs) ruth ellis

Miss Enez Domec-Carre was the teacher of the girls classes at Legacy. This article was an obituary published in 1998 when she died of a stroke aged 90. She was a former Miss Victoria and was known for her physical education skills and for introducing grace and culture to Melbourne. In 1932 she joined Melbourne Legacy and became the chief instructor of girls' physical education until she retired aged 65. In the post World War II baby boom the Legacy evening classes were attended by about 400 girls. She helped organise Legacy Widows and Legatee wives to sew the costumes for performances. Among her proudest moments was a display by 1000 Junior Legatees at the MCG during the 1954 visit of Queen Elizabeth II. As well her work for Legacy she ran physical education, ballroom dancing and debutante preparation classes in Windsor, Elsternwick, Gardenvale and Geelong. She also held a position on the Board of Studies and as director of physical education in Catholic Schools. Recognition of her work included being awarded an MBE in 1971. And in 1997 she received Legacy's highest award, the title of Guest of Honour, for her years of service. See also Cat.No. 01300. Another copy of this article was found with 'Box 10 / JL12' in blue pen. This was part of an archive project JL standing for Junior Legacy items.A snapshot of the life of Enez Domec-Carre who was a huge influence in the life of Junior Legatee girls who attended Legacy classes.Photocopy of a newspaper article on Miss Domec-Carreenez domec carre, girls' classes, girls' club, annual demonstration

This typewriter case allowed the Olivetti typewriter to be securely and free from contaminants to be totally mobile. The Olivetti typewriter company was founded in Italy in 1908 and became a leader in portable dependable typewriters.This particular typewriter contained is a Olivetti Lettera 22, oblique front stroke and portable manufactured after 1950. During the 1950s and 1960s was a time when British and European manufactured goods were still purchased by many Australian consumers. After the 1970s however, there was a shift, mainly in the cities, to Japanese made goods. The invasion of Japanese manufactured goods was relatively slower, especially in rural areas. The demand for long lasting and dependable merchandise was in the rural area still the most important criteria. The ease of setting up this typewriter and its compact mobility was its major benefit to trades people and travelling professionals, e.g. rural doctors, other medical professionals, accountants, lawyers and educators. This item(carrying case) facilitated the growing numbers of professional nomads requiring a relatively light office stationery package e.g. travelling novelist, writer, businessman and academics. This typewriter needed no electrical or battery power to operate it therefore the inside compartment did not require additional storage pockets . Outback Australia, where at this point in time, good available electrical power reticulation and battery power, was a scarce and therefore could not be totally measured as a highly efficient office environment. The protective carrying bag provided the only mobile way to operate in some business and home locations.Although this typewriter cover and its typewriter was purchased from a business in Penrith, Sydney, N.S.W., it is significant that it travelled easily to the Kiewa Valley, demonstrating the mobility of certain sections of the community. This typewriter cover protected the expensive typewriter it contained which was designed by an Italian industrial designer, Marcello Nizzoli, in line with the art deco style of the 1930s and the colour and flexibility of the vibrant 1950s. The underlying theme of manufacturing in the 1950s was to produce equipment that was more efficient than what was inherited from the earlier period of 20th century. Improvements were made to this Olivetti typewriter by Giuseppe Beccio by reducing the number of parts made from 3,000 to 2,000. Protection of such a typewriter was of an utmost necessity. The need for mobile expensive typewriters waned as less expensive typewriters became available. This was the major principle of the Japanese manufacturing juggernauts of the post World War II. Efficiency and low cost material was becoming prime factors in the success of rural industries from the 1960s. Competition from overseas producers was starting to affect rural industries and the removal of the large range of tariff protection, especially rural products, required not only a shift of farm management but a more efficient cost savings modus operandi.This is a semi hard cover (cloth over cardboard on inside, plastic over cardboard on outside), camel coloured outside and tartan cloth covered pattern inside the typewriter case. the case can be opened up by "unzipping" the top from the bottom halves of the case. For carrying purposes the case has two plastic covering metal handles with brass fittings. There are two stitched on brown reinforcement straps encompassing both sides of the case. The two reinforcing straps are brown in colour and a securing strap with a press button at one end to allow an extra securing tongue to keep the cover secure. The top inside of the case has a three quarters long paper compartment (flap style). See KVHS 0455 for Olivetti Lettera typewriter.commercial, protective carry bags/cases for mobile office equipment, mechanical typewriter

A razor strop (or razor strap) is a flexible strip of leather or canvas used to straighten and polish the blade of a straight razor, a knife, or a woodworking tool like a chisel. Unlike honing or sharpening a blade, in which a whetstone removes metal bent out of alignment from the blade's edge, stropping the blade re-aligns the indentations without removing any material. The strop may be a hanging strop or a hand-held paddle. Various abrasive compounds may be applied to the strop to aid in polishing the blade while stropping to obtain a mirror-like finish. The properties of the compound applied will alter the polishing result. Jeweller's rouge is a very fine abrasive compound. The green Chromium(III) oxide compound is most often used as an abrasive compound. Sprays containing diamond particles are another option. Stropping is primarily done with straight razors, used for shaving, as these are the thinnest blades in everyday use, and require stropping at each use, due to the thinness of the blade Two points are key to stropping: Draw the blade spine-first along the strop. By contrast, honing is done edge-first. When you turn the blade at the end of a stroke, turn it over the spine, so the edge moves away from the strop and faces you, and the spine rests on the strop. This preserves the edge – if the blade is turned over with the edge against the strop, this will roll the blade edge, defeating the purpose of stropping As the use of safety razors increased in popularity this 'Jason' strop prolonged the life of each razor blade thus making them economical.A leather 'Jason' strop, for sharpening safety shaving razor blades, with box. Top of Box: J / The JASON / STROP/ Reg. Trade Mark / for SAFETY RAZOR BLADES / Reg. Patent No. 25435/35 ; Back : How to operate the JASON STROP ( instructions) Side: JASON / Razor Strop Dressing / A keen smooth blade will always be assured by the / occasional use of JASON RAZOR STROP DRESSING/ Side: FIFTY SHAVES WITH ONE BLADE ! / by using - JASON and JASON / Razor Blade Strop Razor Blade Dressing. End: JASON / Made by MEIK BROS. Pty. Ltd. / 15-17 Bedford St., Collingwood, and / 287 Flinders Lane, Melbourne, Vic. End: JASON / SAFETY RAZOR BLADE STROP.safety razors, the jason strop, shaving equipment, personal effects, strops, meik bros pty ltd, gillette, collingwood melbourne

Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf#zoom=100 gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949. Historic - Railways Permanent Way and Works - track equipment - Motor Spirit Highly Inflamable Transporting Tin ContainerMotor Spirit Highly Inflamable Transporting Tin Container made of tin Motor Spirit Highly Inflamable puffing billy, motor spirit transporting container

Informal 12 hole golf event, played on Grand Final weekend. This event was started by a group of friends when there were few official golf tournaments played at Peterborough. The event was a stroke event with "mystery handicaps" ie you didn't know your handicap until you finished playing. The event was played on the Sunday of Grand Final weekend (except initially); Friday night traditionally was tea at Boggy Creek Pub and a Fishing Comp on Saturday. The name came about because three of the regular players, Ivan Voss, Bob Loader and R. McKendrick had a hut at the top of the dunes near Crofts Bay. They had a clinker boat on the beach as well. They subsequently built a house in Childers St. It ceased when the original participants were no longer able to play. The date of the first winner is 1980, last recorded winner is 1995. No longer played. further information required. Winners: 2nd August 1980 F. Virgona, 8th March 1981, R Case 25th September 1982, E Brierly 24th September 1983, R Mckendrick, 28th September 1984 D Stead, 28th September 1985 I Turnbull, 27th September 1986 J Charles, 26th September 1987 I Voss, 1988 no winner, 1989 F Carlin, 1990 B Turner, 1991 R Pollock, 1992 S McGuire 25th September 1993 B haskett 1st of october 1994 R pollock 30th of september 1995.Shortened golf driver and cracked ball mounted upon a wooden base with names engraved on metal surround.Engraved names, listed below, on metal plate affixed to the base.golf, peterborough golf club, golf tournment

Frank and Blanche Cornell had their home built in 1904. Mr Cornell was a keen gardener, usually doing 2 hours’ work before going to work. He was a director of Buckley & Nunn, Bourke Street, having worked up from a position as shipping clerk. Frank was a great supporter of and worker for the Empire Day celebrations in the 1905-1911 period and also of the bowling club. He was also a keen photographer. Frank Cornell was first listed in Surrey Hills in 1906 at (6) Lorne Parade. In 1908 the listing gives his occupation as a clerk. He was born in 1869 in Richmond, Victoria and died 15 April 1917 in Surrey Hills from a stroke. His wife Blanche Annie Parsons Cornell (nee Bracher) was born in 1869 in Hokitika, New Zealand; she died on 21 January 1940. Children were: Gilbert Frank Cornell (b1894, Hawthorn; d1908, at Frankston beach, an accidental drowning) Ruth Amelia Cornell (b 1899, Kew; d 29 May 1977, Kew) Lorna Amy Cornell (b 1906, Surrey Hills; d unknown) Patience Blanche Cornell (b1907, Surrey Hills; d unknown). Frank and wife Blanche are buried in Box Hill Cemetery - CE-*-1058. Ruth Amelia married David Ellis, c1922 in Surrey Hills. David was a dentist who practised in Surrey Hills for many years. Patience (Pat) Blanche married Norman Henry Brewer (1893–1975) in 1931 in Surrey Hills.A black and white photograph of a man dressed in a 3 piece suit with flowers in his buttonhole, and a bow tie. He is also sporting a moustache.(mr) frank cornell, buckley and nunn, empire day celebrations, house names, lorne parade, surrey hills, (mrs) blanche amy parsons cornell, box hill cemetery, surrey hills bowling club, 'casallenroc'

Sharped Edged instrument used for cleaning hair from the skin. http://en.wikipedia.org/wiki/Straight_razor A straight razor is a razor with a blade that can fold into its handle.[1] They are also called open razors and cut-throat razors. HISTORY The first modern straight razor complete with decorated handles and hollow ground blades was constructed in Sheffield, England, by Benjamin Huntsman in 1740. Huntsman's process was adopted by the French sometime later. The English manufacturers were even more reluctant than the French to adopt the process and only did so after they saw its success in France.[5] Straight razors were the most common form of shaving before the 20th century and remained that common in many countries until the 1950s. TODAY Straight razors are still manufactured. DOVO, of Solingen, Germany, and Thiers Issard of France are two of the most well-known European manufacturers. Feather Safety Razor Co. Ltd. of Osaka, Japan makes a razor with the same form as a traditional straight, but featuring a disposable blade that can be installed through an injector-type system. Modern straight razor users are known to favor them for a variety of reasons. Some are attracted to the nostalgia of using old and traditional methods of shaving. It is a masculine ritual comparable to pipe smoking. Others profess an interest in reducing the waste of disposable blades.[11][22] Still others agree that straight razors provide a superior shave through a larger blade and greater control of the blade including the blade angle. Straight razors cover a much greater area per shaving stroke because their cutting edge is much longer than any of the multiblade razors. Ivory cut throat razor, with cream case 00121.3.Known as a straight razor.Razor with square point, full hollow ground 5/8” blade and double transverse stabiliser. The centre pin adds stability and rigidity to the handle---I think this is it ROM Parts The narrow end of the blade pivots on a pin, between 2 pieces of ivory forms the handle. LONG EXTRACT FROM WIKI _ SHORTEN to describe 00121 The parts of a straight razor and their function are described as follows: The narrow end of the blade rotates on a pin called the pivot, between two protective pieces called the scales or handle. The upward curved metal end of the narrow part of the blade beyond the pivot is called the tang and acts as a lever to help raise the blade from the handle. One or two fingers resting on the tang also help stabilize the blade while shaving. The narrow support piece between the tang and the main blade is called the shank, but this reference is often avoided because it can be confusing. The shank sometimes features decorations and the stamp of the country of origin. The top side and the underside of the shank can sometimes exhibit indentations known as fluting, or jimps for a more secure grip.[8] The curved lower part of the main blade from the shank to the cutting edge is called the shoulder.[9] The point where the shoulder joins the cutting edge is called the heel. A thick strip of metal running transversely at the junction where the main blade attaches to the shank is called the stabiliser. The stabiliser can be double,[10] single or can be absent in some razor models. The first stabiliser is usually very narrow and thicker and runs at the shank to blade junction, covering the shank and just spilling over to the shoulder. The second stabiliser can be distinguished since it is considerably wider and narrower, appearing after the first stabiliser and running lower into the shoulder. The non-cutting top of the blade is called the back or the spine while the cutting part of the blade opposite the back is called the cutting edge.[11] Finally the other free end of the blade, at the opposite end of the tang, is called the point and, sometimes, the head or the nose.[9][12] There are two to three pins in any handle. The middle pin, if present, is plastic coated and is called the plug.[13] Its function is to stabilise the sides of the handle so that they cannot be squeezed in the middle. When folded into the scales, the blade is protected from accidental damage, and the user is protected from accidental injury. During folding, the back of the blade, being thick and normally with a curved cross-section, acts as a natural stopper and prevents further rotation of the blade out of the handle from the other side shaving, lever, handle, blade, pivot, razor, tang

A razor strop is flexible strip of leather or canvas used to maintain a shaving edge on a thin blade such as a straight razor. Fine powdered jeweler's rouge or other pastes can be added as an abrasive to polish the blade. The strop may be a hanging strip or a hand-held paddle. This one is a hanging strop. Strops were quite commonly found in barber shops and homes before the invention of the safety razor, They are still used for sharpening tool blades. The person using the strop would draw the spine of the blade down along the strop with the blade following, without putting any pressure on the blade. At the end of the stroke, rotate the blade over its spine then draw the spine along the strop again so that the edge moves away from the top. The finer grade of leather strap is used to give the final finish. KEEN EDGE MANUFACTURER In March 1906 Popular Mechanics magazine included an advertisement for Keen Edge Strop. The promise given by the advertiser, Eddy Mfg. Co. (206 Broadway, New York) was “Use the Keen Edge strop for 90 days and if not satisfied return to us and we will refund your money“. The advertisement was for a Combination Razor Strop, “the only strop made which requires no dressing.” Readers were invited to send for a booklet on Razor and the Face. In 1924 Popular Mechanics, published by Hearst Magazines, displayed an advertisement seeking a sales manager “… to sell [to] drug, hardware and cigar stores Keen Edge Strop Dressing, which sharpens straight razors and safety blades and removes old razor strops.” At that time the Keen Edge Mfg. Company was in Dallas, Texas. Razor strops are of historical significance, representing personal effects of men from the time period when men relied on strops to keep a sharp edge on their shaving blade. Strops were commonly owned and used until the acceptance of safety razors.Razor strop, leather and metal. Keen Edge brand, double straps: two straps of different grade leather joined at ends with metal fittings. Stropping faces; sharpening surface is stained red and finishing surface is stained black. One end has padded, bulbous shaped leather handle, the other end has metal, swivel hook hanger. Inscriptions pressed into leather at the ends of the straps. Impressed into leather "FINEST SELECTED HIDE", "KEEN EDGE", "FINISH" (black stained side), “A SHARPENER" (red stained side), “1 2 3”warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, great ocean road, shaving leather, shaving accessory, barber’s equipment, barber shop razor strop, razor strop, straight razor, razor and knife sharpener, keen edge razor strop

V.R Fuel Can for Trolley - Victorian Railways Fuel Can for Trolly Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949.Historic - Victorian Railways - Permanent Way and Works - track equipment - V.R Fuel Can for TrolleyV.R Fuel Can for Trolly - Metal Fuel TinMotor Spirit Highly Flammable V.R 8 ?puffing billy, victorian railways, fuel can, trolley, trolly