Floor length dress of royal blue silk fabric with a metallic thread forming a tinsel like pattern. There is a V neck at front with a high round neck at the back. The bodice front is made from two pieces with a centre seam. The bodice is attached to midriff panel of royal blue satin. At the front the bodice is gathered slightly onto the panel with a V shape at t centre front of the panel. At the hip line centre front the midriff panel narrows and then widens and the panel extends to the hem. The centre panel is divided and has a godet insert in the centre. Fifteen decorative fabric covered buttons with roulette loops are attached at centre of midriff panel. The back of the bodice is one piece is gathered slightly into a high waisted skirt made up of four gored pieces. The side opening (21 cm) at the waist on the LHS has three metal hooks with cotton loops and two press studs. The long sleeves are set in with lily point finish at the wrist. The underside of the sleeve at the wrist has ten decorative fabric covered buttons with roulette loops. Machine and hand stitched.costume, female daywear, blue silk dress

Full length cream synthetic fabric wedding dress with long sleeves and a train. Front and back have a yoke of lace. Three quarter length sleeves are made of the same lace with roulette trim at hem. Inner and outer edges of sleeves ruched for 3 cm. High round neck at back. V neckline at front. Front of bodice has two side darts and two under bust darts. Bodice at waist line has three decorative scallops at front and back. Synthetic fabric of bodice has woven fabric backing. Side opening on left hand side is fastened with nine press studs. Full length skirt of lighter weight opaque synthetic fabric has centre seams at front and back. Fabric is cut on the bias to form a 360? full circle skirt with a train at centre back. An additional section of fabric is attached at either side to complete the circle. At centre back of the skirt is an inverted pleat to create fullness for the train. Hemline is edged with lace with four rows of tucks above the hem, 1 cm apart. Separate petticoat of heavier woven synthetic fabric attached at waist. Petticoat cut on the bias to create 360? full circle skirt with inverted pleat at centre back to create fullness. Narrow turned over hem. Petticoat skirt dips to a V shape at centre front and back seams. Machine stitched.costume, female ceremonial, wedding dress

Ivory coloured waist length silk wedding bodice with front opening. Silk fabric has alternating striped pattern of chequerboard pattern, running stitch pattern and diagonal woven pattern. The bodice is made of two layers of the silk fabric with cotton fabric lining. The front inner layer has two darts from the waistline. The back inner layer has a centre seam and three darts from the waist on either side. The outer layer on both front and back has three knife pleats falling from the shoulders creating a gathered effect. These side panels of pleated fabric create a deep V neckline by crossing over 5cm above the waist. The V shape neckline is filled with an insert of cream and dark green lace with a floral pattern. The lace insert extends to the throat to form a high round neckline. The neckline is edged with cream coloured woven cotton braid. The side edges of the outer layers are trimmed with cream lace with a floral pattern and 5cm zig zag peaked edges that extends from centre waist at the front, over the shoulders and to the crossover section at centre back where there is a decorative silk fabric flower stitched at the crossover point just above the waist. The front opening is fastened with fourteen hooks and eyes plus another hook and eye offset 5 cm above the waist at the crossover point. Set in long sleeves are in two sections. An inner layer of silk fabric widens to the elbow where two five cm frills of gathered tulle are attached. Each frill is edged with a row of silk stitching. Attached below the frills are two 7 cm strips of lace stitched together to form the lower part of the sleeve. The edge of the lace forms the hem at the wrist. Each sleeve has a 5 cm hemmed V shaped split from the hem at the wrist. The outer layer of the sleeve is bell shaped falling from the shoulder to the elbow. This section of the sleeve is edged with cream lace with a floral pattern and 5cm zig zag peaked edges that are stitched to the fabric of the sleeve. Ivory coloured full-length wedding skirt with train. The skirt is made in two layers. The under layer is made from cotton from the waist with a wide border of silk fabric - 18 cm wide at centre front, widening to 37 cm at the side seams. The back of this skirt extends to a train and the border widens to 48 cm. The border section is lined with cotton fabric. At the centre back, the border has two godet inserts to create fullness in the train. The outer layer of the skirt is of ivory silk fabric with alternating vertical stripes of a chequerboard pattern, a running stitch pattern and a diagonal woven pattern. The lower edge of the skirt is edged with an 18 cm border of lace patterned with embroidered circles. The edge of the lace forms a zig zag pattern of elongated V shaped peaks (7 cm). The front of the skirt dips to a V shape at centre front with the point of the V reaching the hemline. The back of the skirt dips below the front hemline in a U shape over the train. The waist band is made of cotton tape. The centre front of the waistband has an embroidered pattern in silk thread. The centre back opening is fastened with seven metal hooks with six cotton loops plus one metal eye on the waistband. There are two cotton tape hanging loops on either side of the inner waistband. Hand and machine stitched.costume, female ceremonial, wedding bodice

Scalebuoy. Invented by Hartley Abbott & patented under the name of the Bendigo Electronic Company, made in various sizes & for different applications, such as to prevent scaling in the boilers at mines. Made up of a sealed glass bulb containing mercury and gasses enclosed within a chromed wire cage & with a chromed handle. The one shown being a hand held shaker model. Scalebuoy sent to Alan from work colleague, Pat Curran in Tasmania. Pat Curran was working as the CEO of a retirement village and found the scalebuoys in the equipment there. Noting the Bendigo manufacturing logo he decided to send it to Alan. Original owner is not known.Bendigo Electronic Coy Ltd A. C. Scalebuoysciences, instruments - general, scalebuoy

Anthony Truscott (1856 -1913) was born in Cornwall. He established a grocery store in Havilah St., Long gully and shortly before his death he handed the business to his so Anthony.Grocer's daybook. The book has a red cover and brown spine. It has 514 pages, used by the storekeeper to record the purchases made by customers. The book covers the years from 1906 to 1912."Ledger" on the spinegrocer, ledger, truscott

Hand written page of notes on Lansell's 222 Mine. Mines Report for 1884. Description of the plant. All designed, made & erected by A. Harkness & Co. at their works Victoria Foundry, High St., Sandhurst.mining, surface equipment, lansell's 222 mine, lansell's 222 mine, mining equipment, a harkness & co., victoria foundry

Photograph: sepia toned photograph, wooden frame, light tan mat, of 13 men 7 standing, 6 seated. Two young boys to either side of group. Men are dressed in dark uniforms, and small military style cap, some with temperance written across the top. At rear - fire reel. Written on bottom of photo: Chuck, gold medallist, Vice-Regal Photographer, Ballarat, London. On rear of frame in pencil ' Bendigo Temperance Fire Brigade. Jim Larson ( or Lawson ) h .? In C in white cap. Label on backstates: ' Large assortment of pictures always on hand. C. Botta, picture framer and .mirror manufacturer, Mitchell Street, Bendigo, Walnut and Bg Mantelpieces made ..the premises.'organization, club/society, bendigo temperance fire brigade, bendigo, temperance fire brigade, chuck

2 chrome plated hand operated hair clippers with adjustable cutters. 1 British & 1 German.Burman & Sons Ltd Made in England, Strong made in Germany.trades, hairdressing, clippers

Cream tin plate German alarm clock, silvered dial with black and gold hands & numerals Brass bezel, legs and handle, convex glass.Schuler made in Germanyhorology, clocks, alarm

Black tin plate alarm clock with two tone cream and white dial labelled Westclox America, black hands and numerals, convex glass and chrome bezel.RD1932 Made in Canada made by Western Clock Co Limited Peterborough Canada.horology, clocks, alarm

Ladies wristwatch in blue velvet box, watch square silver plated case with embossed decoration, round gold coloured dial with a second dial and hand at bottom, brown leather band.H.Bright Watchmaker & Jeweller Carlton & Brunswicj Swiss madehorology, watches

2 Ladies wrist watches, 1 with black leather band circular white face with luminous numbers and hands, separate seconds dial, marked Election Swiss made. The other smaller with no band, white circular face with black numerals and red 12 and wavy pattern on case.Swiss made 0935 84 116361 2horology, watches

Ingersoll eclipse pocket watch and fob chain EPNS case and chain, black numerals with gold dots with separate second hand at bottom. Label inside reads Robt.H.Ingersoll & Bro makers Ely place London 15.5.15Made in USA Ingersoll Eclipsehorology, watches

Large plastic doll 1960's era, dressed in red crocheted dress, white undergarment, white shoes, white socks & red ribbons in hair, also 28 other items of hand knitted and crocheted garments for doll.Evergreen made in Hong Kong No 1027toys, dolls, plastic

Child's bomber-style jacket made of khaki camouflage print polyester, hand embroidered. Purchased in South Vietnam in 1969 by Phil Rogers, Army No:2790936, B Company 6 RAR, and posted home on the birth of his son Brett 31/08/1969.Back: My daddy is in Vietnam. Vung Tau, 69-70, Viet Nam plus a labelled map of Vietnam. Sleeves: Golden dragons Front: Tiger's head, Crossed South Vietnam flag and USA flag.commemorative clothing, souvenir, children

Brown vinyl covered Australian Military Forces Soldier's Pay Book ( 48 pages with crest on front cover) issued to Neil Ernest Swainston on 21/04/1971, Cash Office 30, Paymaster Wendy A Sherwell. Details of payments made are written in pen.Inside front cover lists 'Instructions to Soldier'; back cover has pocket containing green-printed Paybook Variation Authority slips. Small ID photo of Private Swainston stapled to page 48.Hand-written in black marker pen:S16/ Army No. 3801127/ Swainston Neil Ernestpayments, national service - australia

Dark grey hand held super 8 movie camera with zoomCanon camera Co Inc Made in Japanmovie camera, super 8, zoom

Brace and eyed auger bits were used for boring deep holes into timber, providing space for mechanical fasteners, such as bolts or spikes. Made of iron, the pictured tool comprises a Jennings type, double twist auger bit with a threaded point to draw the bit into the wood. The other end of the shank is shaped as an eye and fitted to a hand brace. Sometimes simple cross-bars were used instead of a brace. The eye design provides greater strength than a standard auger bit. This tool’s cradle further secures the bit, preventing unwanted twisting during use. Since the late 1800’s, brace and eyed auger bits such as this were used for boring holes in fence posts, bridge building and other heavy construction.Bit bolted on and held with hook. Brace probably blacksmith made. Bit commercially made. May have been used vertically. Surface pitted.auger, fencing, brace, blacksmith, tool, tools, farm, farming, churchill island

The adze is an agricultural tool, similar to an axe, but the blade is affixed perpendicular to the handle. Used primarily for smoothing or carving wood, the adze can also be used as a hoe. The wooden handles vary in length depending on their particular purpose and can be designed for one handed or two-handed use. This adze was made by Australian farming company, Hytest.Adze. Long, slightly curved wooden handle, with a steel arched blade perpendicular to the handle. Hytesthytest, adze, axe, tool, tools, farming, farm, churchill island

The adze is an agricultural tool, similar to an axe, but the blade is affixed perpendicular to the handle. Used primarily for smoothing or carving wood, the adze can also be used as a hoe. This adze is missing its wooden handle, which may vary in length depending on their particular purpose and can be designed for one handed or two-handed use. Rusted, well worn, blacksmith made with bias on blade. No handle. An adze is a tool similar to an axe.adze, churchill island, farm, axe, tool, tools, blacksmithing, smithing, blacksmith

The double-ended ring spanner served as a useful, manual tool for maintaining farm machinery. The hexagonal rings would be placed over a nut to secure it, before the spanner was rotated to tighten the nut. The ring design provides greater purchase, or grip on all sides of the nut, which in turn reduces the risk of rounding the nut, or slippage. Early spanners were mostly made from iron and hand-forged using an anvil and hammer. Since the mid-19th century, gravity or powered drop forging techniques were used to compress metal for greater strength. Ring spanners produced in the 20th century are mostly made of chrome vanadium steel.stainless steel, some pitting. One end slightly smaller than the otherdouble, ended, spanner, tool, tools, churchill island, farm

Alexander Mathieson & Sons Ltd ('& Sons', after c. 1890), of the Saracen Tool Works, Glasgow, advertised as 'manufacturers of planes, mechanical, engineering and edge-tools'. They received 'prize medals' at the London, Melbourne and Edinburgh International Exhibitions of 1851, 1862, 1880 and 1886, in their 'quest for perfection in tools'. Mathieson's vast output included specialised craft implements for coopers, ship's carpenters, tinsmiths and wheelwrights. The firm originated when master plane-maker John Manners opened premises in Saracen Lane, Glasgow, in 1792. 4 Alexander Mathieson (c. 1797–1852) took over his business in 1821, which he gave as the foundation date of his firm. He was later succeeded by his son, Thomas A. Mathieson (1822–1899), a prominent Glasgow magistrate and preceptor of Hutcheson's Hospital charitable institution. In 1854, Mathiesons moved to East Campbell Street, and had opened branches in Edinburgh, Dundee and Liverpool by 1876. The third generation comprised Thomas O. and James H. Mathieson (born 1867), the latter being a Glasgow bailie (councillor), whose estate totalled an enormous £150,939 in 1926. Mathieson's hand- and small machine-tools (e.g. bandsaws and beading machines) were exported worldwide, especially their 'heavy duty auger bits used... for boring railway sleepers'. Wooden smoothing plane with handle. Adjustable via wedge. Borer holes in handle.Ward blade. Plane made by Mathieson & Son Glasgow Best Guaranteed.plane, block plane, hand tools, carpenter's tools, mathieson, churchill island

A Spokeshave is an ancient woodworking tool, used to shape items by gradually shaving back the wood. Originally made from stone, they evolved to have wooden handles with a steel blade, and the type varied depending on its purpose. It could be used for wheel spokes, chair legs, paddles, bows, or arrows, and was an essential tool for farming and homesteads. More modern examples are now made entirely of metal.Cylindrical length of wood, with tapered handles at each end. The centre section has a steel insert with a brass guard strip, and there is a small crack on woodwork.spoke shave, woodwork, hand tools

This brace would be used to drill into timber. A drill bit would be inserted into one end of the brace and then placed on the timber where the hole is to be drilled. The other end of the brace would be placed against the user’s abdomen, with one hand holding the brace firmly then the free hand would be used to turn the centre of the brace and drill the hole. This type of drilling method was used prior to the use of the electric drill. This brace appears to have been made by the firm of Alexander Mathieson & Sons from Glasgow, Scotland. Alexander Mathieson & Sons Ltd ('& Sons', after c. 1890), of the Saracen Tool Works, Glasgow, advertised as 'manufacturers of planes, mechanical, engineering and edge-tools'. They received 'prize medals' at the London, Melbourne and Edinburgh International Exhibitions of 1851, 1862, 1880 and 1886, in their 'quest for perfection in tools'. Mathieson's vast output included specialised craft implements for coopers, ship's carpenters, tinsmiths and wheelwrights. The firm originated when master plane-maker John Manners opened premises in Saracen Lane, Glasgow, in 1792. 4 Alexander Mathieson (c. 1797–1852) took over his business in 1821, which he gave as the foundation date of his firm. He was later succeeded by his son, Thomas A. Mathieson (1822–1899), a prominent Glasgow magistrate and preceptor of Hutcheson's Hospital charitable institution. In 1854, Mathiesons moved to East Campbell Street, and had opened branches in Edinburgh, Dundee and Liverpool by 1876. The third generation comprised Thomas O. and James H. Mathieson (born 1867), the latter being a Glasgow bailie (councillor), whose estate totalled an enormous £150,939 in 1926. Mathieson's hand- and small machine-tools (e.g. bandsaws and beading machines) were exported worldwide, especially their 'heavy duty auger bits used... for boring railway sleepers'. Iron carpenter's brace, metal handle, rotating knob, thumb screw, rustedATMIEBON (x) Mathiesonbrace, woodwork, carpenter's tools, spofford brace, churchill island

This brace would be used to drill into timber. A drill bit would be inserted into one end of the brace and then placed on the timber where the hole is to be drilled. The other end of the brace would be placed against the user’s abdomen, with one hand holding the brace firmly then the free hand would be used to turn the centre of the brace and drill the hole. This type of drilling method was used prior to the use of the electric drill. This brace appears to have been made by the firm of Alexander Mathieson & Sons from Glasgow, Scotland.Iron carpenter's brace, metal handle, rotating knob, thumb screw ..... rusted.brace, spofford brace, woodwork, tools, churchill island

Hand shears - also called blade shears - were used to shear sheep prior to the introduction of machine shears and are still used today where no power machinery is available. Hand shears consist of two blades with a hinge at the end furthest from the point. The cutting edges pass each other as the shearer squeezes them together and shears the wool close to the animal's skin. In 1892 Jack Howe an Australian shearer sheared 321 sheep in one day using hand shears. This record has never been broken. This pair was made by Burgon and Ball in Sheffield under patent number 294. Filed in 1865, this brand of shears has been in constant production since then, although this pair was probably made in the 1930s.Spring double handled hand shears for shearing sheep."HIND'S PATENT DOUBLE HOLLOW GROUND BURGON AND BALL PATENT NO. 294 (inside a shield with a crown on top) MADE IN ENGLAND"churchill island, hand shear, burgon and ball, shearing

A Sickle is an agricultural hand tool used for harvesting or reaping grain crops using the sharp blade in a swinging or hacking motion. It was also used for cutting back forage and other plant growth. They have been used since early Iron Age times and many examples have been found in the Middle East dating back 18,000 to 8,000 BC. This is a bagging hook – a type of larger and heavier sickle used mainly for harvesting of grain. It continued to be used after industrialisation and the implementation of the mechanical reaper. Designed by British manufacturing firm, Brades & Co, and made to be used by the left hand, its age is unknown. Left handed sickle. Blade painted black; handle varnished. Metal ferrule on handle. Hook on blade at handle endB?RADE? BRADER OZ?sickle, harvesting, churchill island heritage farm

A scythe is an agricultural hand tool that cuts grass and is used by making large sweeping motions through the crop. Eventually replaced by horse-drawn or motorised machinery, they are occasionally still used as they are inexpensive and efficient. There are different types of scythes with larger or smaller blades. This particular scythe has a bored hole in the handle, probably for affixing a long wooden handle. Made by Trojans and Sons, a Melbourne based company that made a wide range of gardening and agricultural tools, this scythe formed an integral part of farming on Churchill Island. scythe with surface rust, no handle, good steel, rough welds on socket, hole for mounting handle (e.g. with screw)TROJAN/264scythe, hand tools, agriculture, churchill island heritage farm

Made and imported by Swedish company, Husqvarna, this machine was used to mince larger pieces of meat. The grinder was clamped securely to a table, and meat was then fed into the machine through the funnel at the top. The wooden crank handle was turned, moving the spiral grinding mechanism, and pushing the meat through the sieve-like fitting at the end. While hand mincers were ubiquitous in the late nineteenth and early twentieth-century kitchens, and was responsible for reducing food waste and promoting frugal ideals, the Husqvarna brand sold over 12 million worldwide.Hand operated mincing machine, larger than usual, with multi small holed attachment in place. Tin plating worn off top edge of bell. Plan wooden handle. Stamped with name, number, etc.HUSQVARNA 10 one side; also on attachment holder. RELIANCE/MADE IN SWEDEN + five pointed star on other side. "H" stamped on crank inside.husqvarna, mincer, hand, kitchen tool

Belonged to Churchill Island Heritage Farm volunteer Jeff Cole's Aunt May Hart, a very stylish woman of the 1920s, keen on horse racing.One pair dark brown rabbit skin (?) gloves. Scalloped, overlocked edge. Three "S" shaped stitching decorations with small punched holes along thumb side of stitching on each gloveCAPE LAMB (?)/ MURRAY GLOVES/6 1/2/ MADE IN AUSTRALIA stamped inside left glove. $15 hand written inside left glove. "721" stamped inside left glove. "20"stamped inside right glove.gloves, fashion, ladies gloves, churchill island heritage farm, may hart