Showing 1923 items
matching industrial
-
Puffing Billy Railway
Cheetham Salt Hopper Truck No12
Trucks of this type were built to carry salt from the saltpans of Cheetham Salt Company works, at Laverton, Moolap and Geelong. Made from wood and steel, it was found that the wood would not erode as much as steel from the salt and this is the reason these vehicles have metal on the exterior of the wagon. Later new stainless steel hopper trucks were used at the works. Historic - Industrial narrow Gauge railway - Cheetham Salt Company at Laverton, Moolap and Geelong.Two Cheetham Salt Hopper Trucks Gauge 2'0" Made from Wood & Steel No. 12 on metal frame of one of the Cheetham Salt Hopper truck A second hopper truck is not numbered.puffing billy, industrial narrow gauge railway, cheetham salt company, gauge 2' 0", salt -
Puffing Billy Railway
H Class Bogie Flat Wagon
This vehicle was used on the Innisfail tramway line in Northern Queensland and given the "H" Classification. It was later sold to Howard Smith Industries. The wagon has been donated to the Museum and sees use on the Museum's 2'0" gauge line. Historic - Industrial Narrow gauge Railways - Rolling stock - Innisfail tramway line in Northern Queensland H Class Bogie Flat Wagon made of Iron, wrought iron and steelh class, bogie, flat wagon, 2'0" gauge -
Puffing Billy Railway
Four Wheel Long Wheel Base Flat Wagon
Built for use at Bachus Marsh on a Cementation contract, these 3 long wheel base vehicles arrived at the Museum in 1982 and are used on the Museum's 2'0" gauge lines.Historic - Industrial Narrow Gauge Railway - Flat WagonFour Wheel Long Wheel Base Flat Wagon made of Steel and Metal puffing billy, bachus marsh, four wheel flat wagon, two foot, 2'0" gauge -
Puffing Billy Railway
Maribyrnong Cordite Wagon
Cordite Wagon - 18½-inch (460mm) gauge wagons came from the Commonwealth Explosives factory at Maribyrnong in Melbourne’s western suburbs. Both have gun-metal wheels, as avoiding sparks was understandably a priority in an explosives factory. Both wagons also have water tanks to drip water on the wheels as an added precaution. Cordite, an explosive used in artillery, was manufactured and pressed into thin sheets, which still contained a quantity of acetone solvent from the manufacturing process. The sheets of cordite were laid in racks of perforated trays in the cordite wagons, which were hand-pushed to the cordite drying-house where the trucks were coupled together in rakes and warm air was blown through them. The acetone, being very volatile, was evaporated out of the cordite and recovered to be re-used in the manufacturing process. Historic - Industrial Narrow Gauge Railway - Commonwealth Explosives factory, Maribyrnong, Victoria, AustraliaCordite Wagon - Rectangular yellow wagon made of wood and brass with aluminium traysThe number 77 is on the endspuffing billy, wooden wagon, 18½-inch gauge, explosives, maribyrnong cordite factory, maribyrnong explosives factory, puffing billy museum, industrial narrow gauge railway -
Puffing Billy Railway
Wonthaggi Coal Skip, Early 20th century
One of two types of four wheel skips widely used on the Wonthaggi Coal Fields for transportation from the underground workings to the surface screening and loading areas. Haulage underground was accomplished by the use of pit ponies, whilst an endless rope system was used to bring the skips to the surface areas. Much of the coal for the colony of Victoria was sourced from Newcastle and the Hunter Region in New South Wales, along with local supplies from private and co-operative coal mines at Outtrim, Jumbunna and Korumburra in Gippsland. After the 1909–1910 strike by coal miners in the Hunter Valley, the Victorian state government were determined to ensure stability in local supplies of coal. The State Coal Mine and the town of Wonthaggi came into being in 1910 to supply coal for the Victorian Railways. It was one of the largest and most dangerous collieries in Australia. At its peak in 1926 the mine produced 2,435 long tons (2,474 t) per day, with the Victorian Railways buying 90% of production. In 1928, Wonthaggi coal accounted for around 60% of Victorian Railways coal consumption.Historic - Industrial - Victorian Railways - Narrow Gauge Railway rolling stock - Wonthaggi Coal Fields, Victoria, AustraliaRectangular steel bin with wood frame and steel wheelspuffing billy, coal skip, wonthaggi, wonthaggi coal fields, 2'0" gauge, brown coal -
Puffing Billy Railway
Four Wheel Brick Skip
Typical of many small four wheel skips constructed to transport raw bricks from the moulding press to the kilns for firing.Historic - Industrial Narrow gauge railway - Fritsch, Holzer & Company Brick works, Hawthorn, Victoria, Australiatwo Wooden skips with steel wheels "JF 12" & "SB 34"puffing billy, fritsch, holzer & company, brick skip, fritsch, holzer & company brickworks, pressed red brick -
Puffing Billy Railway
Side Tipping Timber Skip, circa 1900?
Side Tipping Timber Skip Wooden Contractors Wagon. Gauge 17 inch (430mm) Typical of the many side tipping wagons used for soil and rock disposal in construction work and mining throughout Australia and the world. The wagon would be loaded with soil and pushed along a short line to the end of track where the load would be emptied out to either side. By using a central pivot the wagon’s body can be tipped either side to allow the contents to be easily removed ready for the next load.Historic - Industrial Narrow Gauge RailwayWooden bodied, steel framed side tipping skip.puffing billy, side tipping skip, industrial narrow gauge railway -
Puffing Billy Railway
End Opening Wagon, 1900?
End opening Wagon Gauge: 17 inch (430mm)Historic - industrial Narrow gauge RailwayEnd Opening Wagon - Made from wood and steel with one end that openspuffing billy, four wheel wagon -
Puffing Billy Railway
Lathe - Gap Bed, early 1900s
Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy -
Puffing Billy Railway
Sectioned Tangye Steam Operated Water Pump, 1900s
Sectioned steam pump so that the pump workings can be seen. Inscriptions & Markings: Tangye Birmingham, This steam pump was presented by the colonial gas Assn Ltd (brass plaque) The Colonial Gas Association was originally formed in London on 2 February 1888, as The Australasian Gas Association Limited. The primary objective of the company was to provide investment capital to help finance the construction and management of gasworks being established by the London engineering firm John Coates & Co in metropolitan cities and regional towns throughout Australia and New Zealand. By 1890, the Australasian Gas Association had acquired gasworks at Benalla, Shepparton, Wangaratta, Warragul, Maldon and Seymour, and had constructed a large gasworks at Box Hill to supply the eastern suburbs of Melbourne. In 1893, the company's name was changed to the Colonial Gas Association Limited. During the 1890s, the company acquired regional gasworks in Queensland, Western Australia and South Australia, followed by its first gasworks in New South Wales, in 1911. In 1914, the company consolidated its metropolitan supply area by purchasing the Oakleigh and Footscray gasworks. Further expansion occurred in the 1920s with the purchase of established gasworks at Williamstown, Frankston and Dandenong and the acquisition of ten further gas undertakings in Queensland and New South Wales, making the firm the fifth largest gas producer in Australia. info from The Colonial Gas Association Limited, circa 1893 https://collections.museumvictoria.com.au/items/1553322 Originally formed by the five Tangye brothers from Cornwall as James Tangye & Brothers in 1857, this Birmingham engineering firm grew to become one of the largest suppliers of jacks, pumps, steam and oil engines, hydraulic presses, gas producers and machine tools in the late 19th and early 20th centuries. The successful sideways launching of I.K. Brunel's 'Great Eastern' from the mud of the Thames in 1857 using Tangyes hydraulic jacks gave the firm much needed publicity and new orders flowed in. To finance expansion, George Price provided additional capital and the company name became Tangye Brothers & Price in 1859. A new factory known as the 'Cornwall Works' was built in Clement Street, Birmingham. In 1872, the firm became Tangye Brothers and in about 1879- 1880 began production of internal combustion stationary engines based on Horace Robinson's patents, later using the Otto four-stroke design for its Soho range of gas engines. Examples of the Soho engine were exhibited by the firm at the 1880 Melbourne International Exhibition. Petrol and oil engines were made from the 1890s onward, and by 1910 had developed into the Model B, BR and AA series engines. Tangyes supplied custom-built pumps and presses for particular applications, becoming a major exporter of engineering equipment. In 1884, Tangye Brothers opened a custom-built branch office, showroom and warehouse in Melbourne at Cornwall House in Collins Street West, advertising the full range of engineering products. These lantern slides images are taken from Tangyes product catalogues from the 1910-1925 period and are believed to have been used as sales promotional aids in Australia by the Tangye Brothers. info from https://collections.museumvictoria.com.au/articles/4670 Historic - Industrial Steam Operated Water Pump built by Tangye Bros and used by the Colonial Gas Company - Melbourne, Victoria, AustraliaSectioned steam pump so that the pump workings can be seen. Tangye Birmingham, This steam pump was presented by the colonial gas Assn Ltd (brass plaque)puffing billy, steam pump, sectioned, tangye bros -
Puffing Billy Railway
The Quasi Arc Co Ltd Generator - Flat Belt Driven D.C, 1900s
QUASLARC Generator Built by the Quasi-Arc Co. Ltd. Victoria London SW.1, This generator is believed to have been used for welding purposes. The generator is driven by a belt from a nearby steam plant. The quasi-arc co ltd 6 kw. d.c generator 60/30 volts 0/200 amps 1200 rpm comp cont rating No 4696 Historic - Industrial Generator Large casting with a drive pulley on one end, cast aluminum covers, bronze makers plaque. The quasi-arc co ltd 15,grasyenor ????ens. Victoria,London,S.W.1 This machine is designed for use with ????? Arc electrodes 6 kw. d.c generator 60/30 volts 0/200 amps 1200 rpm comp cont rating No 4696puffing billy, generator, welding, quasi - arc -
Puffing Billy Railway
Steam Powered Water Pump, 1900s
Steam Powered Water Pump in active use on George & George BoilerHistoric - Industrial Steam Powered Water Pump in active use on George & George Boiler Steam Powered Water Pump Blue with steel rods and brass valves.Snow steam Pump works Bufflalo, N.Y.,U.S.A Size 3x2x3 Number 51520puffing billy, water pump, steam, blue, snow steam pump works -
Puffing Billy Railway
Wagon, Explosives, 1900s
18½-inch (460mm) gauge wagon came from the Commonwealth Explosives factory at Maribyrnong in Melbourne’s western suburbs. It has gun-metal wheels, as avoiding sparks was understandably a priority in an explosives factory. It also has water tanks to drip water on the wheels as an added precaution Historic - Industrial Narrow Gauge Railway - Commonwealth Explosives factory, Maribyrnong, Victoria, AustraliaExplosives Wagon - Four wheel wagon with timber frame, copper water tanks and bronze wheels.explosives wagon, puffing billy, commonwealth explosives factory, maribyrnong explosives factory -
Puffing Billy Railway
New Record Saw Bench, circa 1930's
Saw Bench - New Record Saw Bench Timber framed with steel wheels, belt driven saw blade powered by a Rosbery internal combustion engine. The Rosebery Engine No C28437 R.P.M 800 H.P. 6 Manufactured By Westinghouse Rosebery Pty.Ltd. Sydney Rosebery Engine Works Ltd began as the engine and pump manufacturing division of Buzacott & Company, and in 1923 became an incorporated company. In 1935, Westinghouse gave Rosebery Engine Works the right to manufacture and sell nearly all Westinghouse products. The name of the company then changed to Westinghouse Rosebery Ltd From the late nineteenth century, petrol engines gradually supplanted steam engines for running a wide range of machines, and in turn petrol engines were largely supplanted by electric motors. The Champion was a successful small petrol engine made by the large Sydney company, Westinghouse Rosebery, based on the American-designed Fuller and Johnson engine. With hopper cooling and a fuel tank between the skids, and weighing only 240 pounds (109 kg), it was easy to mount on wheeled transport, making the Champion a self-contained mobile source of power. Engines of this type were used in rural areas for driving chaff cutters, small saw benches, pumps and orchard sprayers. These engines were also commonly used in both rural and urban areas for powering concrete mixers. Both Westinghouse Rosebery in NSW and Toowoomba Foundry in Queensland made these engines in large quantities, beginning in the 1920s when tariff protection made local manufacturing viable. The production of small petrol engines continued in Australia until the 1970s, when reduced tariff protection led to increased competition from cheaper imported engines. Historic - Industrial Timber working - belt driven saw blade powered by a Rosbery internal combustion engine. Timber framed with steel wheels, belt driven saw blade powered by a Rosbery internal combustion engine. The Rosebery Engine No c28437 R.P.M 800 H.P. 6 Manufactured By Westinghouse Rosebery Pty.ltd. Sydneysaw bench, puffing billy, new record, internal combustioin, westinghouse rosebery pty.ltd., rosebery pty, internal combustion engine. -
Puffing Billy Railway
Flat Belt Driven Mill, 1930s
Flat Belt Driven MillHistoric - Industrial - Flat Belt Driven MillMade from iron.flat belt driven, mill, puffing billy -
Puffing Billy Railway
Lister Auto Truck
The Lister Auto-Truck was a small monowheel tractor built for moving light loads around factories, railway yards and similar sites. They were built by R A Lister and Company of Dursley, Gloucestershire, well known for their range of small stationary engines The Auto-Truck was one of several monowheel tractors to appear in the 1920s and '30s, with the availability of small, reliable petrol engines, as developed for motorcycles and the stationary engines for which Lister were already known. These were tricycle vehicles, with the single leading wheel used for both drive and steering. Their simple construction carried most of the mechanism on this wheel as a single unit, the chassis with the trailing wheels being little more than a trailer for balance. Simplicity was a key feature. The engines were single-cylinder and air-cooled. Ignition was by magneto, rather than requiring a battery and electrical system. One of these designs was produced in the 1920s by George Grist of the Auto Mower Co., Norton St Philip, Somerset. The engine was a JAP 600 cc four-stroke air-cooled sidevalve, a typical small engine of the time. The Auto Mower Co. were Lister agents and when Lister heard of this 'Auto-Truck' they bought one for use in their own factory. It was used to carry heavy engine castings from the foundry to the machine shop. Lister customers saw them and there was such interest in wanting to buy them that Lister negotiated with Auto Mower to build them under licence. Although Lister were already well known for their small petrol stationary engines, these were heavy cast-iron engines with water hopper cooling and unsuitable for vehicle use. Lister remained with the JAP engine for the Auto-Truck. The Auto-Truck was designed for use in factories or other places with smooth surfaces of concrete or tarmac. This allowed the use of small solid-tyred wheels with only simple suspension, making the vehicle simple, cheap and lightweight. They had little ability on soft surfaces though and could even topple over if driven carelessly across slopes. Their design was a compromise between the top-heavy nature of the tall engine grouping above its wheel and a well thought-out chassis for stability. The bearing between them was a large diameter ring roller bearing, mounted at the lowest part of the chassis. This gave rigidity and stability, even after long wear. A ring of rolled channel girder was attached to the engine group and rollers on the chassis carried the load upon this. On early Auto-Trucks this bearing is set very low, in line with the chassis members, and is covered by thin steel plates. The front panel of the engine cover is distinctive with large ventilation holes and a Lister signature cut through it. Strangely this panel is made of thick cast iron, providing substantial weight high on the engine and only adding to its top heaviness. To improve visibility of moving vehicles in noisy factories, this panel was often painted white, the rest of the vehicle being Lister's usual brunswick green. The driver was seated on a Brooks bicycle saddle, which in recognition of the lack of vehicle suspension, was carried on the end of a cantilevered bar that acted as a leaf spring. A wide handlebar on the engine group was used for steering. A squeeze bar the width of this handlebar engaged the clutch. Controls included a hand throttle, a gear lever with two forward and one reverse gears, and a large handbrake lever. The engine unit rotated freely for a full 360° rotation. When used in reverse, the Auto-Truck could either be driven from the saddle, looking backwards over the driver's shoulder; or they could dismount, swivel the engine unit around and control it as a pedestrian-controlled truck from behind. Under the engine cover were two equal diameter tanks, a fuel tank for petrol and a shorter oil tank. Engine and chain-drive lubrication used a total-loss oil system, controlled by a small pump and needle valve. Info Ref: Lister Auto-Truck - Wikipedia https://en.wikipedia.org/wiki/Lister_Auto-TruckHistoric - Industrial monowheel tractor for moving light loads around factories, railway yards and similar sites.The Lister Auto-Truck - small monowheel tractor Made of steel with three wheels. Powered by a J.A.P single cylinder petrol motor which is Hand Cranked to start.Lister puffing billy, lister, lister auto truck, monowheel tractor -
Puffing Billy Railway
Blacksmith's Bellow
Blacksmith's Bellow Used by the Blacksmith to blow more air into his fire which further heats the flame to provide a temperature hot enough to heat the steel that he is working onHistoric - Industrial - Blacksmithing equipment Blacksmith's bellow. made from wood and leather and wrought iron fittings puffing billy, bellow, open hearth, blacksmith, heat -
Puffing Billy Railway
Fowler - Diesel Locomotive
Fowler Diesel Locomotive Diesel Locomotive fitted with a Detroit 471 engine. One of the early diesel locomotives used to work on the Queensland canefields. Privately Owned - Exhibit on loan Historic - Industrial Narrow Gauge Railway - Diesel Locomotive that worked in the Sugar cane fields in Queensland Diesel Locomotive made out of steel wrought iron and iron puffing billy, fowler, locomotive, diesel, detroit 471, industrial narrow gauge railway -
Puffing Billy Railway
KBW Belt Driven Slotting Machine
KBW Slotting MachineHistoric - Industrial - Slotting MachineLarge metal KBW Slotting Machine KBWbelt driven, puffing billy, slotter, kbw, slotting machine -
Puffing Billy Railway
Sugar Cane Truck No. "1076" - Gauge 2'0"
Sugar Cane Truck "1076" Gauge 2'0" A four wheel truck of simple construction typical of many hundreds used on the canefield tramways of Queensland and Northern New South Wales. Donated by Moreton Sugar Mill, Nambour, Queensland in 1965Historic - Industrial narrow Gauge railway - sugar cane truck used at Moreton Sugar Mill, Nambour, QueenslandWooden Truck with Winch 1076 puffing billy, sugar cane truck, industrial narrow gauge railway, moreton sugar mill -
Puffing Billy Railway
Allen Twin Cylinder Engine Driving A Brush Electrical Generator
Allen Twin Cylinder Engine Driving A Brush Electrical Generator Built by W. H. Allen & Co, Ltd ., Bedford, England ( serial Number R1/14738/4) it was used at Kodak Australia, Abbotsford plant , to provide power through the attached Brush Electrical Generator ( serial 21177 of 1929 ) for the photographic plant. Donated by Kodak ( Australia ) Ltd. in 1966Historic - Industrial Twin Cylinder Engine Driving A Brush Electrical Generator used by Kodak Australia, at their Abbotsford plant, Abbotsford, Victoria, AustraliaTwin Cylinder Engine Driving A Brush Electrical Generator made of steel , iron, wrought iron, brassBuilt by W. H. Allen & Co, Ltd ., Bedford, England ( serial Number R1/14738/4)puffing billy, twin cylinder engine, brush electrical generator, w. h. allen & co, ltd -
Puffing Billy Railway
Zeehan & North East Dundas Tramway Bogie 1896, wagon bogie, 1896
Zeehan & North East Dundas Tramway Bogie 1896 The North East Dundas Tramway (NEDT) was a 2 ft (610 mm) narrow gauge tramway on West Coast Tasmania that ran between Zeehan and Deep Lead (now Williamsford). It was part of Tasmanian Government Railways. The line was opened in 1896 to carry ore from the Williamsford mines to Zeehan where it would be loaded onto another train for shipment to Burnie. The narrow-gauge (2 ft) was chosen because of the extremely difficult terrain that the railway crossed, requiring several big trestle bridges, including one at the foot of Montezuma Falls. After some rain the engine and carriages would get soaked by spray from the falls. There was a break-of-gauge with the mainline 1,067 mm (3 ft 6 in) system at Zeehan. The railway was closed in 1932. The rolling stock for the Tramway was built in the Launceston Railway workshops, and comprised twenty five eight-wheel low-side trucks, tare 3 tons 1 cwt. 1 qr., load 10 tons; six eight-wheel flat trucks, tare 2 tons 18 cwt. 1 qr., load 10 tons; two four-wheel bolster trucks, for carrying long timber, tare 1 ton 19 cwt., load 5 tons; and four passenger cars, each with six cross-seats with reversible backs, to carry eighteen passengers, also a locker for mails and parcels. All trucks and cars have cast-steel wheels 21 inches in diameter and are fitted with automatic vacuum brakes. The trucks have side levers and the cars have hand-screw brakes. The vacuum brake can be worked from the engine or from the passenger cars, which act as brake vans. When this brake was introduced, one effect was to accelerate the journey speed by about 10 minutes owing to more even running on down gradients. Historic - Industrial Narrow Gauge railway - Bogie used on the Zeehan & North East Dundas Tramway, Tasmania, Australia Bogie made from steel, iron and wrought ironZN & NTDS ML TRAM 1896 Griffinpuffing billy, bogie, zeehan & north east dundas tramway bogie, zeehan & north east dundas tramway, industrial narrow gauge railway, gauge: 2' (610 mm) -
Puffing Billy Railway
Benwerrin Coal Company Coal Skip, circa 1899 - 1904
BENWERRIN COAL COMPANY SKIP This quarter ton coal truck or skip was used at a small mine situated at Benwerrin near Deans Marsh in Victoria’s Otway Ranges. The mine first opened in 1899 and closed in 1904. With the fuel shortages due to World War 2, the Benwerrin Coal Company reopened the mine in 1941. The coal was loaded into skips and winched out of Box’s Creek valley on a narrow gauge incline to a loading point that was close to the Deans Marsh-Lorne Road. It was then taken by road to the Deans Marsh Railway station. The average gradient of the tramway was 1 in 4 over a length of just under 500 metres (1600 feet). The gauge of the tramway has often been referred to as 375mm (or 15 inches) as shown on the map opposite taken from “Sawdust and Steam”. However, actual measurements of the wheels show the gauge to be 400mm (or 16 inches), which is quite unusual as is the small size of the skip itself. The mine produced up to 30 tonnes of brown coal each week until it closed in 1949 and the incline tramway and its skips were abandoned. Preservation of this coal truck came as a result of interest by the Tramway Museum Society of Victoria (TMSV) in the Barlow or Box type rails that it ran on. These rails had originally come from the Beaumaris Horse Tramway and were obtained by the Benwerrin Coal Company from Hayden Bros’ abandoned timber tramway at nearby Barwon Downs. Members of the TMSV visited the mine in the 1960s only to find that most of the tramway had recently been recovered for scrap. There remained a significant number of relics around the mine adits including most of the skips. One of these remained in good condition and it was recovered for preservation in May 1967. It was restored but never displayed and a second restoration took place by the author over 2012/13 so that it could be placed in the Menzies Creek Museum where it was delivered in February 2013. Little remains of the mine today with trestles and sleepers destroyed in the “Ash Wednesday” Bushfires in 1983. References: Houghton, N (1975), Sawdust and Steam, Light Railway Research Society of Australia. Historic - Industrial Narrow Gauge Railway - Benwerrin Coal Company , Benwerrin , Victoria, AustraliaCoal Skip - made of Iron sheet and wrought iron frame & wheelsB,C.Co Melbournepuffing billy, coal skip, benwerrin coal company, narrow gauge -
Puffing Billy Railway
Twin Cylinder Racking Engines
Twin Cylinder Racking EnginesHistoric - Industrial - Twin Cylinder Racking EnginesTwin Cylinder Racking Engines made of metal, iron and steeltwin cylinder racking engines, puffing billy -
Puffing Billy Railway
Clarkat Tug Locomotive, 13 April 1943
Clarkat A Clarkat Aircraft Tug that has been converted to run on Rails, This Clarkat 'B' was one of 11 machines shipped on 13 April 1943 to the Lathrop Holding & Re-consignment Depot in Lathrop, California. and was used at Jack's Magazine, Maibyrnong, Victoria and later on at Coal Creek Historical Village, Gippsland, Victoria. Clarkat Tug Model C S/N Cx30F Made by Clark Tructractor Div of Clark Equipment Co Battle Creek Michigan U.S.A Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 Historic - Industrial Narrow gauge railway equipment - Jack's Magazine, Maribyrnong, Victoria, Australia Clarkat Aircraft Tug that has been converted to run on Rails, made of steel Coal Creek Tug Clarkat Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 clarkat, clarkat aircraft tug, puffing billy, jack's magazine -
Puffing Billy Railway
Portable Compound Steam Engine, Marshall & Son's - Builders Number 48317, circa 1908 / 1909
Portable Compound Engine - Marshall & Son's. Builders Number 48317 Built by Marshall Sons & Co., Ltd., Gainsborough, England (Builder’s Number 48317 of approximately 1908/1909), to the order of Robison Brothers, Engineers, South Melbourne. It was used for operating a pump to supply irrigation water at Robinvale in Northern Victoria. Robison Bros & Co. P/L was founded by James McFarlane Robison and his brothers in 1854, initially as plumbers and coppersmiths, the firm expanded into general engineering, boiler-making and brass, iron and steel founders and became one of Melbourne's most important engineering firms. They constructed railway bridges, gold mining equipment, railway locomotives, pumping stations, brewing vessels, abattoir machinery, amongst much else and including the first turnstiles at the Melbourne Cricket Ground. A portable engine is either a steam engine or an internal combustion engine, that remains in one place while operating (providing power to machinery), and can be easily moved from one work site to another. Mounted on wheels or sometimes skids, it is required to be towed between work sites.Historic - Industrial Portable Compound Engine - steam engine - Marshall & Son's. Marshall & Son's Portable Compound Engine - Builders Number 48317 made of steel Marshall & Son's. Builders Number 48317puffing billy, state rivers and water supply commission of victoria, portable compound engine - marshall & son's., portable compound engine, marshall sons & co., ltd., robison bros & co. p/l -
Puffing Billy Railway
Tank Locomotive, 0-6-2 T No.1 "Delta", 1950
0-6-2 Tank Locomotive No.1 "Delta" Gauge 2'0" Identification: 1 Delta Type: 0-6-2T Builder: Perry Engineering, Mile End, South Australia Builder's number: Perry 7967.50.4 of 1950 Building date: 1950 Current status - Static Exhibit Wheel Arrangement 0-6-2T Cylinders (Diameter X Stroke) 10 inches X 18 inches Boiler Pressure 180 psi Driving Wheel (Dia.) 28 ½ inches Weight 16 tons Coal Capacity 27 cubic feet Water Capacity 500 gallons The Perry Engineering Co, Mile End, South Australia built a total of 18 locomotives for the 2’0” gauge tramways used by the sugar industry in Queensland. This 0-6-2T locomotive was built by Perry Engineering Co. Ltd. of Mile End, Adelaide as their Builder's No. 7967.50.4 of 1950. It was used at Qanaba Mill, Bundaberg where it was known as No.1 "Delta". / Qanaba Mill No.1 No. 1 “DELTA” 0-6-2 TANK LOCOMOTIVE Gauge: 2 foot Built by Perry Engineering Company of South Australia in 1950 (Builder’s number 7967.50.4), “DELTA” is a medium sized Australian designed locomotive featuring Walschaert’s valve gear driving piston valves. Weighing 16 tons (16.3 tonnes) it was one of the post-war narrow gauge steam locomotives, which worked in the canefields of Queensland until 1978. “DELTA” worked at various sugar mills in the Bundaberg area and was finally withdrawn from service at Quanba Mill after a life of 28 years. Obtained by the Puffing Billy Preservation Society in 1981. Delivered to Australian Estates Co., Kalamia Mill named DELTA in 1950. Purchased by Fairymead Mill as No 20 DELTA. Purchased by Millaquin Sugar for Qanaba Mill as No. 1 DELTA, 1970 Withdrawn from service, 1978. Obtained by Puffing Billy Preservation Society for display at the Puffing Billy Museum.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used in Queensland in Sugar Mill service. Locomotive No.1 "Delta" - Steam Locomotive - made of steel, and wrought ironDelta0-6-2 tank locomotive no.1 "delta" perry engineering - puffing billy railway perry 7967.50.4 of 1950, puffing billy, qunaba sugar mill, bundaberg, perry engineering, delta, steam locomotive, 0-6-2 tank locomotive no.1 -
Puffing Billy Railway
Malcolm Moore No. 1013 - Four Wheel Diesel Rail Tractor Gauge 2'0", circa Nov 1943
Malcolm Moore No. 1013 Four wheel Diesel Rail Tractor Gauge 2'0" Malcolm Moore rail tractor (Builder’s Number 1013) It was built for the Australian Army in 1943. It was sold to the Inkerman Sugar Mill in Queensland around 1948 for hauling cane and shunting at the works. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It was purchased from the Inkerman Mill of Pioneer Sugar Mills in 1982. Historic - Industrial narrow gauge Railway - Diesel Rail Tractor - used by the Australian Army and Inkerman Sugar Mill in QueenslandDiesel Rail Tractor made of iron and wrought irondiesel rail tractor, puffing billy, inkerman mill, industrial narrow gauge railway, gauge 2’0”, inkerman sugar mill, australian army -
Puffing Billy Railway
Climax - Geared Steam Locomotive No. 1694, 1928
Climax geared locomotive No. 1694 in active service on special occasions - stored at Emerald Station A Miraculous Survivor Climax locomotive No.1694 is a miraculous survivor of a rare breed of steam locomotive. For about 100 years from the mid-1850s sawn timber was carted from Victorian sawmills to the nearest railway station by timber tramway. These tramways were generally very rough, steeply graded, sharply curved, and of narrow gauge. Many had wooden rails, and horses provided haulage. The better ones used steam locomotives. In all about fifty steam locomotives are known to have worked on Victorian timber tramways. These locomotives were usually somewhat peculiar - made to cope with arduous, rough conditions, rather than speed. Climax locomotive No.1694 is the only one of these locomotives to survive intact. It was built in 1928 by the Climax Manufacturing Company, Corry, Pennsylvania, USA, for the Forests Commission of Victoria. The distinctive feature of the Climax locomotive is that the cylinders do not directly connect to the driving wheels. Instead they drive a cross shaft near the centre of the locomotive. From there the drive is transmitted to the small driving wheels through rotating shafts, universal joints, and bevel gears. The driving wheels are mounted in two four-wheel bogies so that they can easily follow sharp curves in the track. None of these features are found in normal steam locomotives. The result is a locomotive that is extremely powerful for its size, and that will cope with sharp curves and steep grades with ease. But this is at the cost of speed, Climax locomotive No.1694 is just about flat-out at 13 km/h (8 mph). Climax Locomotive Built in 1928 for the Forests Commission of Victoria and painted all-over black with the name CLIMAX painted on the sides of the cab in white block letters, this locomotive was issued to the Tyers Valley tramway which branched off the Moe to Walhalla line at Collins Siding. This locomotive was withdrawn from service in 1949 following the closure of the tramway and in 1950 it travelled from Tyers Junction to Collins Siding to Erica where it remained stored until 1965. Loaned to the Puffing Billy Preservation Society for its Steam Museum, it was taken to Menzies Creek in 1965 where it remained until 1982 when the Emerald Tourist Railway Board bought it and transferred it to Belgrave for restoration. It was returned to service for special use on the Belgrave to Gembrook line in 1988 painted in its original all-over black livery, except that the word “Climax” on the sides of the cab was now painted in the style of the Climax Manufacturing Co., a style that this locomotive had never carried.Historical - Industrial railway - Forests Commission of Victoria, Timber Logging Climax Locomotive Climax geared Steam locomotive made of steel and wrought iron Climax 1694climax locomotive works, climax, geared steam locomotive, puffing billy, climax locomotive no. 1694, steam locomotive -
Puffing Billy Railway
861 - John Rees - Decauville Steam Locomotive - formerly John Benn, 1886
861 John Benn Locomotive - in active service - Emerald Station Built in 1886 by Société Anonyme Usines Métallurgiques du Hainaut - Locomotives Couillet for the West Melbourne site of the Metropolitan Gas Company, as a four-wheel tank locomotive similar to 986 and named “John Benn”. The West Melbourne gas works sourced its coal from Maitland, New South Wales, and the coal was brought by ship to a wharf adjacent to the West Melbourne gas plant. John Benn and Carbon were used to haul the coal over a 762 mm (2 ft 6 in) gauge railway from the wharf to the gasworks, a distance of about 450 metres (500 yards). It was withdrawn from service in the 1930s and stored until sold privately in 1962. It was rebuilt by its new owners in the style of an American locomotive of the 1880s and was used for some years at Walhalla. It currently has the name “J.C. Rees” and is used in active service for the 861 Footplate Experience. Wheels: 2-4-2ST Builder: Couillet Build Date: 1886 Construction No.: 861 Empty Weight: Unknown Weight on Drivers: Unknown Driver Diameter: Unknown Tractive Effort: Unknown Boiler Pressure: Unknown Cylinders: Unknown Fuel: Coal Gauge: 30 inchesHistoric - Industrial railways - Metropolitan Gas Company Ltd, Melbourne Steam LocomotiveDecauville Steam Locomotive 861 John Reespuffing billy, narrow gauge, industrial narrow gauge railway, metropolitan gas company, decauville 43, steam locomotive, john rees, john benn, 861 locomotive, couillet, 861