For over 45 years, Richard has used Wendy regularly for recreational fishing and occasional sailing out of Queenscliff. He has the original cotton canvas sails that were fitted on the boat when she was built, and which still are in working condition. Richard says that one of his favourite pastimes has been trolling for pike around Swan Island, close by Queenscliff, ensuring that the heritage of this Lacco-built boat fishing boat is preserved. In about 2015, Wendy underwent a rebuild including: a new centre-case, ribs and deck, and a new Yanmar engine. The works were done by Bryon Miller of Peninsula Wooden Boats. Wendy remains berthed, fore and aft, at Number 12 pile in front of Queenscliff Lonsdale Yacht Club. Well known couta boat in QueenscliffeAustralian made Kopsen vortex bilge pump.Kopsen Vortexcouta boats, 'wendy", bilge pump

Six page typed document, signed by Albert Richardson, and a handwritten copy of same. Written on top right of typed document: 'These recommendations all adopted by General Meeting Bendigo and District Tourist Association, 30.11.1967' Document describes the 'Central Nell Gwynne area, situated at West Bendigo, approximately 150 yards north of main Calder Highway to Mildura, local section Marong Road, which is a public purposes reserve under Section 14 of the Land's Act 1958. The steel poppet legs donated by the late Jack Barker to the City Council for preservation be a permanent reminder of the gold mining era and containing the engine beds and 20 head crushing battery foundation, be developed as a mining museum for tourists, educational and historical purposes'bendigo, mining, central nell gwynne

Memorandum from the Office of D.R.S. Sup't Bendigo 1st July, 1938. FPM/S. Issues of Tools Comprising Enginemen's Kits on Engines. The sup't of loco Supplies has drawn attention to the enormous increase in the number of tools issued for Enginemen's kits, and below is set out the issues for 6 months under the old system and the issues for the 6 months under the new system. The percentage increase in hand hammers, hand lamps and feeders is particularly large. The above state of affairs is giving much concern and unless an improvement results it is probable that the whole system may be abandoned and the old method reverted to. Enginemen are requested to give this matter close attention in order to ensure the success of the present system. F.P. Martin District R.S. Superintendentorganisation, union, a.f.u.l.e

Document. Cannons at Eaglehawk. Typed document by the Bendigo Branch of the Royal Historical Society of Victoria on the cannons at Eaglehawk. It reads - The two cannons were originally ship cannons, smooth bore type and later modified by the insertion of a rifled tube. This suggests that they were used as fort land guns in gun emplacements, and it is possible that these were mounted around Port Phillip Bay during the Russian scare at the turn of the century. The large ring at the rear is for lashing down to control recoil, and the swivel mounts enable elevation. These were placed in position at Eaglehawk by ox team, and at a later stage a steam traction engine overturned attempting to move one. In later years a large earth mover was used to move them a few feet.cottage, miners, cannons at eaglehawk

Document. 3 page typed document titled 'Resources of Bendigo Goldfields'. An address to the citizens of Bendigo Goldfield. Mentions gold figures from the period 1898 - 1908. Document mentions the engine drivers strike and Mr. A. J. Moore, consulting mining engineer who had a paper on the Bendigo Goldfield appear in the Chemical Engineering and Mining Review. Mentions number of companies on the dividend list from 1870 - 1920. Also mentions in March 1891, 19 companies were over 2000 feet. Lansell's 180 was 2640 feet. Also large brown envelope, McColl, Rankin & Stanistreet with notes re - Romance of Goldfields, Premier Companies, Sebastian Mining Leases, Resources of Bgo Goldfield, and Sheepshead Line of Reef.cottage, miners, resources of bendigo goldfield

Single page photocopy of a report by Mr. J. Harrison, Mayor of the City of Ballaarat, dated 2nd May 1932 of the "brave deed" of Mr. Charles Foster, ESCo driver who rescued a small boy from in front of a tramcar. Council complimented him on his bravery and recommended a letter be sent. Has been a typed original, has number 334 in top right hand corner. On base of page in handwriting has a note regarding an obituary for a Mrs. John Whytes (?), Mayoress? Collected by Mr. Colin Homes, 5331 6036 of the Ballarat Engine and Machinery Preservation Society, April 1998, with some notes on trolley buses in Council Correspondence Inwards and a reference. VPRS series 2500 Unit 155.trams, tramways, esco, accidents, foster charles, city of ballaarat

This photograph is of the square-rigged schooner "Alma Doepel". Details added to the back of the photograph incorrectly describe the vessel as "Amy Doepel / ketch / Amy Doepel". The rigging on the vessel dates the photograph to sometime between 1931-1933. The location is yet to be determined. Frederick Doepel was a shipping agent in Bellinger Valley, NSW. He employed an experienced shipwright to build Alma Doepel, which was made from local timber. He named the ship “Alma Doepel” after his baby daughter Alma. The ship was registered in Sydney and launched 19th October 1903, and her first sea voyage was in December. She traded in timber Port Macquarie/Bellinger River and New Zealand. “Alma Doepel” was purchased by Henry Jones & Co., Hobart jam makers, in partnership with Harry Heather, her new captain, in 1916. The ship was then registered in Hobart. She carried jam and timber to the mainland, particularly Melbourne, and brought back cargo for Tasmania. She even carried the piles for the building of Portland Harbour. When Harry Heather passed away in 1937 he was succeeded by Eric Droscoll. Before the square-rigged "Alma Doepel" left for Tasmania on March 8th 1937 she was fitted with a new set of sails, becoming a fore-and-aft rigged schooner. She had been the last 'top sail' schooner in Bass Strait trade! "Alma Doepel" continued her coastal trading until 1942, when she was requisitioned by the Army. In January 1943 she was left in Melbourne by her crew and the Army took her over, taking her to Sydney in February, 1943. She was relaunched by the Army in 1944 minus two of her masts and her small 1936 engine, and was fitted with three large bus engines. In March 1945 she headed for the war zone, delivering cargo up and down the coast of New Guinea, at one time carrying over 400 troops. In 1946 she returned to Hobart where the Army re-converted her back for Bass Strait trading and returned her. In January 1947 Eric Driscoll took “Alma Doepel” to the eastern Tasmanian coastal port of St. Helens, trading cargo of local mountain ash timber to Melbourne on the mainland until 1959. She was then stripped down to her hull with only a single mast and two engines, and fitted with wooden bins on rails in her hold. From 1961 to 1975 she carried limestone to a factory to make carbide. Michael Wood and David Boykett, two of the governors of "Sail and Adventure", then bought her for the price of her two Gardiner engines and in 1976 they brought her to Melbourne. An Alma Doepel Supporters Club was formed to support the ship’s major restoration to a topsail schooner. In 1987 she was overhauled in Adelaide, with the support of Elders IXL and she returned to Sydney to lead the Parade of Sail on Bicentenary Day, 25th January 1988. She returned to Melbourne in February and began sail training voyages in Port Phillip Bay, operating from an office on Station Pier. The Alma Doepel Voyagers Club was started. Trainees joined the crew in sailing the ship over nine or ten days of instruction in sailing and seamanship. These trips plus chartered trips and fund raisers continued until early 1999, when she was no longer in a condition to operate; she needed a lot of attention. She lay idle in Victoria Dock for quite some time. In April 2001 “Alma Doepel” was taken to Port Macquarie’s Lady Nelson Wharf where she became a museum ship maintained by volunteers. In 2008 she had time in dry-dock and after sea-trials headed off to Victoria Harbour, Docklands, in Melbourne, where she is currently being restored with the help of The Supporters.This phot graph is significant for its connection with the Bass Strait trade, being the last top-sail schooner to brade across the strait. The photograph is also significant in its representation of the the sailing ships that traded around Australia in the 1930s.Photograph of "Alma Doepel " a wooden, 3 masted, square rigged sailing schooner built in Sydney, launched in 10/10/1903. Photograph is sepia coloured, mounted on card, inscription on the back. Information also provided with photograph. Photograph (marked incorrectly on back) "Amy Doepel / ketch / Amy Doepel". Sticker with "91" in pencil. Information provided (dated incorrectly) "1943, Sydney, New South Wales"flagstaff hill, warrnambool, shipwreck coast, maritime museum, maritime village, photograph, alma doepel, frederick doepel, henry jones and co, harry heather, eric droscoll, alma doepel supporters club, elders ixl, parade of sail, bicentenary day, alma doepel voyagers club, last top sail schooner in bass strait trade, square-rigged, fore-and-aft rigged

In 1901 Cameron was captain of the Rokewood Rifle Club. John Cameron was a Rokewood blacksmith in 1902. John (Jack) Richard Watson was the son of Thomas Watson (10/11/1838 - 27/04/1920) and Emma Eliza Jane Phillips (25/05/1844 - 12/10/1925) and was born at Yendon on 16/12/1876 and died 11/10/1973 aged 96 at the Wimmera Base Hospital in Horsham while residing in Murtoa. Still a teenager Thomas reached Melbourne in the 1850's and found work helping to build the Spencer Street Bridge over the Yarra Yarra, as it was known then, before making his way to the Ballarat Goldfields. After being tricked out of a claim he sought work with the Victorian Railways, and later acquired a farm at Yendon. Emma Phillips was born in Geelong and had moved with her mother to Ballarat. Emma was a member of the Ballarat Philharmonic Orchestra and sang in the choir of St Pauls Church in East Ballarat, where they were married. Jack worked in the gold mining industry - firstly as a braceman at the New Kohinoor Mine at Sebastapol and then to a mine at Rokewood, both times following his older brother Frederick George. He later worked in 15 different mines before changing occupations. He was employed as an engine driver for the Murtoa Waterworks Trust at the Murtoa Power Station when he lost his lower left arm when it was caught in an engine belt in 1929. Jack married Edith Emma Yung (01/07/1887 - 05/10/1988 ) who was born at Allendale and died aged 101 at Wendouree after livivng most of her married life at Murtoa. They had five children all born in Murtoa: Richard Henry (Harry); Edith 'Alice'; Grace; Ernest Alfred (Alf) and Jonn Grenville (Gren). They were married at Yendon. Sepia photo of eighteen men and one girl. Eight are in uniform, and two are identified as Boer War soldiers. They all stand in front of Cameron Coach Builders showroom and workshop. The person fifth from the left is J.R. Watson.Front top Rifle Club (Murtoa - crossed out) Rokewod 1898; Lower LHS South Africa Boer War; C - Rokewood Rifle Club; Loer RHS J.R.Watson. Sign on Building: Agricultural & Mining & Smith above Cameron Coach Builder. Verso: Madeley Photo Corindhap plus a signature.corindhap, rokewood, rokewood rifle club, j.r. watson, cameron coach builder, john cameron, emma eliza jane phillips, thomas watson, john richard watson, edith emma watson

Cyrus Chambers was a self-described mechanic who started out winding bobbins in his father's woollen mill and went on to invent machines that changed their industries. Cyrus Chambers came from Quaker parents the ninth of thirteen siblings, he once said a year before his death. “I believe I have succeeded because, first, I was industrious; second, because I made a study of the subject that was before me.” At age 7, Chambers went to work in his father’s mill. His job was to monitor bobbins—wooden spindles around which thread was wound and to remove and replace them as they became full. "There was no child labour law at that time," he later recalled. Chambers loved machinery and always regarded himself as a mechanic rather than an inventor. At age 16, Chambers was sent to learn dentistry with an older brother, (Edwin) who was already in the field and willing to take him on as an apprentice. Chambers was talented at working with small parts. He used his brother's dental instruments to build a miniature high-pressure steam engine of silver. It ran at 3,000 revolutions per minute and weighed less than a half-ounce. At that time it was the smallest engine that had ever been constructed. The engine was displayed at the 1876 Centennial and is now in a permanent collection at the Franklin Institute USA. Chambers major invention was the paper folding machine and came from reading that school teachers made less than the young girls who were employed to fold book pages as they came off the press. He told friends that his first efforts were to make the machine that would fold newspapers after demonstrating his device he met with Horace Greeley of the New York Tribune who advised Chambers would never invent the machine that would be able to fold his newspaper or books. In less than a year Chambers had built a full-size machine capable of folding large newspapers and books and was installed at J B Lippincott & Co folding pages for the "Comly Speller" this machine ran successfully for twenty-five years until the printing works burnt down. Chambers then went into partnership with a brother and they established the firm "Chambers, Brother & Co" at a plant in Philadelphia. It was also observed in 1910 and a fact that there was not a periodical or newspaper printed or recently published book that had not gone through one of Chambers inventions. Chambers went on to produce many mechanical inventions and improvements to existing tools and machinery most notable was his invention for the machine that would make clay bricks. This machine made forty bricks per hour and by the end of Chambers life after many improvements, it could make more than four hundred. Although there were a large number of bold cutters made of this patent at Cyrus Chamber’s foundry in Philadelphia, the item is associated with a notable American inventor of the nineteenth century. This particular patent for a bolt and rivet cutter won Chambers the prestigious Elliott Cresson Medal. This cutter is just one of the many inventions and mechanical improvements that Cyrus Chambers made during his lifetime, contributing to the ongoing development of mechanical improvements that were occurring in American industry of the time and therefore a notable addition to the Flagstaff collection.Cast iron bolt cutter with removable tempered steel cutter. Chambers New No. 2.Raised embossed lettering on cast body of cutter "New No 2" on one side, "Chambers Bros & Co" on the other sideflagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, cyrus chambers, bolt cutter, paper folding machine, brick making machine, elliot cresson, elliot cresson medal, franklin institute, gold medal, rivet cutter

A porter illegally in the signal box moved the points under a train coming into the south platform from a siding. The 5th carriage took two lines as shown, and brought down the overhead stanchions over both the passenger and goods lines. For about 36 hours, the service beyond Mitcham was maintained by steam trains connecting with electrics at Mitcham. Men are pictured putting up temporary overhead stanchions over the passenger lines around 10 a.m. on Saturday 22/6/1945 and another photograph shows the steam crane near the signal box lifting the Melbourne end of the derailed carriage. The other picture is on the same day 22/6/1945 of A2 engine at Box Hill. See also Item 11003 for another photo of the derailment. Accompanying typed sheet reads, "...shows the steam crane about outside the signal box lifting the Melbourne end of the derailed carriage".

Two publicity cards for Australian Aerial Services Ltd a. heart-shaped fold-out card highlighting the safety record of Australian Aerial Services Ltd. 'Flying with Shell' pop-out on card with image of bi-plane 'There is no need to be Half-hearted about taking a Flight in our Aeroplanes!When you are up aloft with us you are perfectly safe'; b. rectangular card highlighting safety record of AAS Ltd with aerial route map on reverse. Inside card: We will not stunt; Land on Unknown Grounds; or Fly unnecessarily Low. We always - Take off into wind; Overhaul our engines and aircraft periodically; and Consider comfort of our Passengers' Red stamp of 'Wilkinson & Lavender Ltd on back of card - Booking agents for Australian Aerial Services Ltd'business, transport, aviation

Various articles for Newsletter ('Marunari??) for November???? 1. Re Jack Moorhead (''the most competent engine driver in the Bendigo field'') with handwritten copy of same; 2. 3 pages of handwritten notes for inclusion in the newsletter - various topics; 3. ''The Canons (sic) on Camp Hill'' - history of the Lookout Tower site and flag post, cannons and statue - semi-nude lady - which was damaged in storm and later removed. Source of information for this item attributed to Misses D and D Davenpor, London and the Bendigo Advertiser; handwritten notes re this same article. 4. ''Boys will be boys'' by Mr A Richardson - article based on Annual Report of the Secretary for Mines and Water Supply, 1885 re 11 year old lad who fell down mine; handwritten notes on same article.document, names of bendigo pioneers, jack moorhead.

Demonstrates a souvenir item for the opening of the electric tramways in Ballarat in the form of a postcard which has actually been used to send a message. Has a strong association with the people who sent and received the card.Postcard size Souvenir Tram ticket, printed using blue ink on one side with fare, photos of power station, engine room, boiler room and a tram & No.10344 stamped on edge. On reverse side is space for stamp, address etc., - with line & "postcard' etc., printed in red ink. Letter/note to Ethel Hodgson of Lethbridge, stamped in Ballarat on 26-8-1905. Fares given on card are : Mount Pleasant and Orphanage and Grenville St. 3d, or Grenville St. and Tram sheds 3d. Printed in a blue/grey ink of various shades onto a white card. Acted as a souvenir card. One Penny stamp, with Ballarat Cancellation stamp and - "5" stamped on the top of the postage stamp. See also Reg Item 608 and 7084 for further versions of this object.Letter on rear and Has I.R. Kellett in ink in the top right hand corner.trams, tramways, esco, opening, ballarat, tickets, letters

Colour postcard with serrated edges of MMTB tram No. SW5 834 southbound in St Kilda Road with the Shine of Remberance in the background. Has as number of parked motor cars on either side of the road. Tram is showing destination of "East Malvern - Darling Road", route 3. Has ads on ends and side of tram, but out of focus. One is for "Dufor Engine Valves" Card by Nucolorvue. On rear of card printed in dark green ink is "MELBOURNE, VICTORIA/ St. Kilda Road with tram and Shine of Remembrance." Also wording for stamp location, copyright etc. On left hand edges is "ML 132", Set EW. Second copy added 21/07/2001. Card is ML 132 NCV1106 - a lot more sharper or in focus card, different colours.trams, tramways, melbourne, st kilda road

Auction catalogue for a sale on 13th March, 1946 under instructions from the Commonwealth Disposals Commission at the Army Salvage Depot, Fishermen's Bend. An extensive sale including Caterpillar, Cletrac, International Diesel Tractors, Elec. Generators, Elec. Motors, Chevrolet, Dodge, Ford V8, Motor Engines, Harness, Steel Shelving and Miscellaneous Equipment. J. H. Curnow & Son were the auctioneers. Catalogue has column for £, S and D down the right side of the page to write in the price of each lot. Contains a description of some lots. The back cover has a black and white photo of the entrance gates to the Commonwealth Disposals Commission Auction Depot. It has a clock in the top centre and two sets of double iron gates. The Prahran Telegraph Printing Co. were the printers of the catalogue.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - army salvage depot, commonwealth disposals commission, j h curnow & son, j l jamieson & co, w g wedd, the prahran telegraph printing co

Hard bound book, 172 pages, including end covers, 10 sections, title "Mind the Curve", with subtitle "A history of the Cable Trams", stitch bound to hard red Rexene covers with gold block title on the spine only. Dust cover has the title, author, drawing of Bourke St and details of the book and author on the returns. Written by John D Keating, published by the Melbourne University Press in 1970. Has index, acknowledgements, table of contents, list of illustrations and references Looks at the establishment, construction, operation and demise of the cable tram system in Melbourne. Provides location details of the engines houses, tramcars, ticketing, management, politics, the Northcote line and the workers. 2nd copy added from the collection of Colin Jones - title page signed by John Keating - see image i5/trams, tramways, melbourne, mmtb, cable trams, mto co, horse trams

The Liquidator, Bendigo Amalgamated Goldfields Ltd. To Miss G. Alice Jones. Re Hamilton. Pink paper dated Nov. 1, 2, 4, 8-9, 11, 14, 19, 20, 21, 26, 29, Dec., Jan. 29, Feb. 1, 1930, Dec 17, 19, 21 to 24 1929, July 13, 21, 24, 29, 30, 31, Feb. 1, 2, 3, 4, 5, 6, 7, 8, 10, 26 1930 and 28/3/30. Items include write to Hamilton for £8 damages for trespass to engine house on lease from Horwoods, interviewing people, writing letters to various people and attending court. "R516 Posted 28/3/30 by BF?" written in the top left corner.the miss g. alice jones collection - account, bendigo amalgamated goldfields ltd, hamilton, mr stanfield, horwoods, mr. ;hyett, mr w j stephens, leggo & co, mr c curnow, mr h m leggo, mr clarkson, mr ennor, church of england, mrs frew, horwoods foundry

Typed copy of recount by Albert Richardson of a fire at Unity Mine on Tuesday 8-10-1907. Report from the Bendigo Advertiser Wednesday October 9th 1907. Notes mention Fire Brigade, miners, how the fire started and how the men down the shaft escaped when the rope crash down the shaft. On the back is a handwritten carbon copy of notes titled Famous Gold Mines of Bendigo and Eaglehawk. Notes give yields of gold for alluvial and quartz mining. Deep Shafts in 1904 of which there were eleven with a depth of more than 3000 feet and 53 over 2000 feet and two which were more than 4000 feet. Wages for 1911 for Engine Drivers and Firemen and Boiler Attendants. Note on winding plants and air compressors.document, gold, ulster gold mining coy no liability, ulster gold mining company no liability, unity mine fire 8/10/1907, bendigo advertiser 9/10/1907, garden gully reef hotel, wm addicoat, louis pabst, edward morris, conrad inglefinger, edward fuller, frederick allen, wm whitford, mr jewell, carlisle mine, famous gold mines of bendigo and eaglehawk, new chum line, garden gully line, hustlers line, victoria quartz mine, new chum railway, mines report 1911 p15, albert richardson

The Procession of floats travelled from the Eltham Shopping Centre to Eltham Lower Park on Saturday 10th April as part of the Shire of Eltham centenary celebrations program. One of three photographs. The Infant Welfare Centre and BP service station can be seen in the background. Participants in the parade included the Eltham Film Society, Scout group, Eltham volunteer fire brigade, riders on horses, including Jock Read on his horse Shamus in front of the fire truck, and horse and carts. A cowley roller from the Melbourne Steam traction engine club and a McDonald roller represented Eltham Shire Council in the 19th and 20th centuries. Another float includes a bark hut with trailer representing pioneers with a banner reading "The trues heores our pioneers". One view shows Eltham Village under construction by H.M. Keast & Sons, Master Builders.This photo forms part of a collection of photographs gathered by the Shire of Eltham for their centenary project book, "Pioneers and Painters: 100 years of the Shire of Eltham" by Alan Marshall (1971). The collection of over 500 images is held in partnership between Eltham District Historical Society and Yarra Plenty Regional Library (Eltham Library) and is now formally known as 'The Shire of Eltham Pioneers Photograph Collection.' It is significant in being the first community sourced collection representing the places and people of the Shire's first one hundred years.Digital imagesepp, shire of eltham pioneers photograph collection, shire of eltham, shire of eltham centenary, centenary celebrations, parade floats, parade, jock read, fire engine

This ship's boiler pipe brush would have been used to keep the steam boiler pipes in good working order. The bristles are arranged in a round shape to fit against the sides of the boiler pipe and clear away debris. The brush has a loop for storing it on a hook so the bristles won't become damaged. The ship's boilers created steam to power the ship's engines. Some larger steamships had several boilers and therefore several funnels. Early steamships also have masts and sails, giving them the option of steam power or wind power. The first successful steamboat trial in America was in 1787 when John Finch displayed its features on the Delaware River in Philadelphia. The first steamboat in Australia was the Sophia Jane, which arrived in Sydney in 1831. The ship traded cargo and passengers between Sydney and Newcastle. This ship's boiler pipe brush is unique in our collection and an essential item in the maintenance of steam boilers. It is connected to the era of steamships, which in Australia began in 1831 with the arrival of the first steamship in Sydney. Pipe brush; long twisted wire handle with stiff bristles around the base section, arranged in a cylindrical shape, and a loop at the other end. Used for cleaning pipes of a ships boiler.warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, steam boiler, steam boiler brush, boiler maintenance, boiler brush, pipe brush, steam boiler pipe, steamship, steamboat, steam power

Fordson Henry Ford set up the company Ford and Son in 1917, it later became known as Fordson. Henry had previously tried to interest the directors of the Ford Motor Co in producing agricultural machinery, but when this met with no success he set up the new company to market the tractor he had created. Fordson: Model N 1929-32 Produced at Cork 1932-1945 Produced at Dagenham The Fordson Model N replaced the Fordson Model F. Production of the Model N started in Cork in 1929. Production of the Fordson Model N was transferred from Cork to Dagenham in 1932. The Model N featured a 27 HP engine, standard rear fenders (mudguards), a higher voltage ignition system, and optional pneumatic tires. In 1935 power take-off (PTO) was available as an option on the Model N. Historic - Farm Machinery - TractorSteel Tractor - Orange with black wheels.Fordsonpuffing billy, fordson, tractor

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

Steele's Reef was opened in 1859 along with a number of other reefs in the Yandoit area. The reef was worked by small mining parties until the late 1880s. In 1887, the Steele's Reef Quartz Mining Company fixed steam pumping machinery and commenced sinking a shaft. The company were unable to find a profitable ore body and after two years work closed down. By this time their shaft had reached a depth of 150 feet. The mine was then taken over by the Pioneer Quartz Mining Company who appear not to have worked the mine. In 1906, the Steele's Pioneer Company commenced work, erecting a winding winch at the old shaft sunk by the Steele's Company. The next year the company erected a 10-head battery, set of poppet legs, a pumping engine. Sinking the shaft a further 100 feet, the company struggled to find payable ore and soon closed down.Colour photographs of the remnants of Steele's mine at Yandoit, Victoria. steele's mine, yandoit, mining, ruins

In 1898 a recommendation for a railway of 2 ft 6 in gauge was handed down by the Parliamentary Standing Committee on Railways, to cost $138,000. Construction began in 1900. About 100 men were engaged in laying and ballasting the track while others, not included in the 100, formed the earthworks, culverts and bridges. Locomotive operations initially were two 2-6-2 Tank engines of the narrow gauge A class, dubbed "Coffee Pots", and these were used on the work trains between 1900 and 1902. Because of the lengthy periods of waiting time required to unload sleepers and rails or to load ballast meant that a handy replenishment of coal and water supply was necessary. With earthworks specified to the bare minimum landslips in the narrow cuttings were frequent so a repairer was stationed in each length to deal quickly with minor slips until 1904 when the cuttings were widened.B/W. The driver and seven other men on locomotive 5A and its flat cars at Beech Forest during construction of the line in c.1902. beech forest; railways; loco 5a;

Like so many ships that were used during WWII, she was laid up and remained idle for several years, until finally in 1948 the US Government sold her at auction and the highly decorated USS Barnett, ex MS Santa Maria was officially purchased by the well known Italian Multi Millionaire ship owner Mr. Achille Lauro on April 13, 1948. Soon she headed for a Baltimore shipyard where she received some work to ensure that her engines that had been shut down for a considerable time, were back in full working condition. When the work had been completed she was certified for her delivery voyage to Italy! The delightful all white MS Surriento was ready to depart Genoa on her very first voyage to Australia in her brand new passenger/migrant liner role. A framed oil painting of the migrant ship MV SurrientoSurrientoms surriento, migrant ships, emmigration

WANNON 567 gross tons. Lbd: 167'4" x 26'6" x 11'. Steel hulled, single screw steam coaster, coal burner (burnt briquettes when on Melbourne-Tassie run); 3cyl triple expansion steam engine, 61 nhp; built 1919 at Enkhuisen, Holland, as Boschpolder; 1920 as British flag Rawlinson; 1922 to Canterbury Steamship Co. Ltd. Lyttleton, N.Z, as Gale; 1935 to Belfast & Koroit Steam navigation Co. Ltd., Melbourne, renamed Wannon to ply the Portland, Port Fairy, Warrnambool, Apollo Bay, Melbourne trade route after the loss of S.S.Coramba off Phillip Island. World War 2 as (S-153) carried general equipment, stores to U.S. Army camps at islands such as Woodlark, Kiriwina, Goodenough. Also served at Lae, Finschhafen and Wewak. Returned to owners and in 1957 went to Hong Kong shipbreakers hand tinted photograph of shipship, boat, sea, river, s.s.wannon