This is a set of nine photographs of technicians from the Royal Australian Survey Corps operating aerial surveys equipment c1980s. In photo .1P, CPL Steve Gloster was operating a RC10 air survey camera mounted in an Australian Army Pilatus Porter aircraft. The Wild RC10 super wide-angle air survey cameras were first introduced in 1971, were equipped with virtual distortion free lenses for supplementary, spot and special photography. In photo .2P, Roger Rees was operating Air Profile Recorder (APR) equipment. it was possibly taken during OP NERVOSE 84, sometime between June – August 1984 when based in Ngukurr, Northern Territory. The APR was operated at this time in unison with an RC10 camera. In 1963 the Royal Australian Survey Corps introduced the radar airborne profile recorder (Canadian Applied Research Ltd, Mark V, Airborne Profiler Recorder) was introduced for 1:100,000 mapping to replace terrain heighting by aneroid barometry. Later in 1974-1975, the Australian developed WREMAPS II airborne laser terrain profile recorder was introduced. In photo .3P, Neil Jones appears at the door of Airsearch Beechcraft Queen Air aircraft, Registration / Serial VH-MWX. This aircraft was typically used by RA Svy on air survey operations flying mission with Aerodist, APR and RC10 camera equipment. The Australian Army’s Pilatus Porter (short take-off and landing turbo propeller) was also equipped with a Wild RC10 aerial mapping camera for identification photography. The Pilatus Porter was also used on RA Svy’s map field checking operations. Photo .9P was taken at a survey station at an unknown location. In this photo an Australian Army Kiowa Light Observation Helicopter (LOH) is supporting a field survey party undertaking Magnavox AN/PRR-14 portable Doppler satellite observations. The satellite receiver’s antenna is plumbed over the survey ground mark surrounded by white plastic panels. The panels were used to identify the survey station on aerial photography. Introduced in 1974–1975, the Magnavox AN/PRR-14 portable Doppler satellite (US Navy Navigation Satellite System – TRANSIT) receivers and computing system provided independent three-dimensional point positions anywhere in the world, anytime, in any weather accurate to about 1.5metres with precise satellite ephemerides. The Bell OH-58 Kiowa LOH was a family of military helicopters used for observation, utility, and direct fire support. It was identified by RA Svy in the mid-1970s that considerable time was lost in replacing unserviceable remote equipment by road. Therefore Aerodist operations (pre-dating satellite receiver operations) were fully supported by Army’s Kiowa LOH aircraft. This is a set of nine photographs of technicians from the Royal Australian Survey Corps operating aerial surveys equipment c1980s. .1P to .3P, .5P to .9P - Colour and black and white photos on photographic paper and scanned at 300 dpi. .4P - Colour photo on 35mm slide film and scanned at 96 dpi. .1) & .2) - Photo, black & white, c1980s, CPL Steve Gloster operating an RC10 air camera. .3) - Photo, colour, 1984, Roger Rees operating Air Profile Recorder (APR) equipment. .4) - Photo, colour, c1980s, Neil Jones at the door of an Airsearch Beechcraft Queen Air aircraft, typically used by RA Svy on air survey operations. .5) - Photo, colour, c1980s. A Beechcraft King Air aircraft, also used by RA Svy on air survey operations. .6) - Photo, colour, c1980s. An Australian Army Pilatus Porter, used by RA Svy on air survey and map field checking operations. SGT Peter Mustart is possibly in the foreground. .7) to .8) - Photo, colour, c1980s. An Australian Army Pilatus Porter and unidentified personnel, used by RA Svy on air survey and map field checking operations. .9) - Photo, colour, c1980s. An Australian Army Kiowa helicopter supporting a field survey party undertaking Magnavox AN/PRR-14 portable Doppler satellite observations. There are biro marks on photos .4P to .9Proyal australian survey corps, rasvy, army survey regiment, asr, fortuna, aerial surveys

The portable lockup at Eltham is not original to the site. The date of construction is unknown, believed from the 1880s. It is a prefabricated design and each of the timber panels are individually numbered on the inside surfaces. It is amongst a large group of portable lockups, categorised as 'Portable Lock Up - Timber - Later' and also known as the "Casterton style", based on the only known plan for portable lock ups, built for the Casterton Police Station, in 1907. The later portables have been in use since the 1880s. It is not known how many lock ups of this type have been constructed in Victoria. At least 50 examples have been documented around the state. Of these, 42 are known to be extant. The original 1860s site lockup was a 2-cell bluestone construction. Some of the original bluestone remains. It was used in the 1970s as traffic island edging at the intersection of Main Road and Wattletree Road where it was painted white then later relocated back to this site in the 1980s to be used as edging for a driveway access off Main Road beside the former Police Residence where the Police Station originally stood. Evidence of some of this edging remains in place today leading to the replica Police Station. Other blocks were used to define the garden edging in the carpark at the rear of the residence.This lockup used to be located at the Police Station in Pryor Street and was then stored in Youth Road before being acquired for the Local History Centre 3 colour photographseltham, main road, police residence, local history centre, eltham district historical society, courthouse, youth road

Two short sections of flooring cut for distribution during Deakin Universities ‘Open Day’ in December 1994. This was during the conversion of Dalgety Wool Store to Deakin University’s Woolstore Campus. These small pieces of timber are part of Geelong’s history and were salvaged from the Dalgety Woolstores during the renovations. Hundred of meters of ironbark, red gum, pine and other timbers, some more than a century old, were reclaimed from the site and have been recycled as furniture and featured building materials for the woolstore campus. The old brick stores, located on a formerly neglected section of the Corio Bay shoreline, now house the administration and chancellery, architecture and building schools, information technology services, the student union, a cafeteria and, as the focal facility, a Great Hall seating 1500 people and acoustically tuned for symphony orchestras. The refit was developed from the existing grid of substantial timber columns and beams extending over 52,000 square metres. This framework was filled with lightweight panels to enclose workplaces and removed in some parts to establish courtyards, atriums and streets. The brick facades were redefined with new doors and double-glazed windows in proportion to original fenestration. Bright colours and industrial finishes identify the new insertions.Square sections of redgum lumber cut into floorboards. The sides of the lumber have a grove cut on one side and a matching section to fit within this groove on the other side. This has been done to ensure the floorboards have a tight and consistent fit with one another. The bottom of the lumber also has an additional grove running through the middle of the redgum. On top, one of the sections of lumber has three nail holes, which travel all the way through to the bottom of the wood.deakin university, dalgety wool store, red gum

The Lister Auto-Truck was a small monowheel tractor built for moving light loads around factories, railway yards and similar sites. They were built by R A Lister and Company of Dursley, Gloucestershire, well known for their range of small stationary engines The Auto-Truck was one of several monowheel tractors to appear in the 1920s and '30s, with the availability of small, reliable petrol engines, as developed for motorcycles and the stationary engines for which Lister were already known. These were tricycle vehicles, with the single leading wheel used for both drive and steering. Their simple construction carried most of the mechanism on this wheel as a single unit, the chassis with the trailing wheels being little more than a trailer for balance. Simplicity was a key feature. The engines were single-cylinder and air-cooled. Ignition was by magneto, rather than requiring a battery and electrical system. One of these designs was produced in the 1920s by George Grist of the Auto Mower Co., Norton St Philip, Somerset. The engine was a JAP 600 cc four-stroke air-cooled sidevalve, a typical small engine of the time. The Auto Mower Co. were Lister agents and when Lister heard of this 'Auto-Truck' they bought one for use in their own factory. It was used to carry heavy engine castings from the foundry to the machine shop. Lister customers saw them and there was such interest in wanting to buy them that Lister negotiated with Auto Mower to build them under licence. Although Lister were already well known for their small petrol stationary engines, these were heavy cast-iron engines with water hopper cooling and unsuitable for vehicle use. Lister remained with the JAP engine for the Auto-Truck. The Auto-Truck was designed for use in factories or other places with smooth surfaces of concrete or tarmac. This allowed the use of small solid-tyred wheels with only simple suspension, making the vehicle simple, cheap and lightweight. They had little ability on soft surfaces though and could even topple over if driven carelessly across slopes. Their design was a compromise between the top-heavy nature of the tall engine grouping above its wheel and a well thought-out chassis for stability. The bearing between them was a large diameter ring roller bearing, mounted at the lowest part of the chassis. This gave rigidity and stability, even after long wear. A ring of rolled channel girder was attached to the engine group and rollers on the chassis carried the load upon this. On early Auto-Trucks this bearing is set very low, in line with the chassis members, and is covered by thin steel plates. The front panel of the engine cover is distinctive with large ventilation holes and a Lister signature cut through it. Strangely this panel is made of thick cast iron, providing substantial weight high on the engine and only adding to its top heaviness. To improve visibility of moving vehicles in noisy factories, this panel was often painted white, the rest of the vehicle being Lister's usual brunswick green. The driver was seated on a Brooks bicycle saddle, which in recognition of the lack of vehicle suspension, was carried on the end of a cantilevered bar that acted as a leaf spring. A wide handlebar on the engine group was used for steering. A squeeze bar the width of this handlebar engaged the clutch. Controls included a hand throttle, a gear lever with two forward and one reverse gears, and a large handbrake lever. The engine unit rotated freely for a full 360° rotation. When used in reverse, the Auto-Truck could either be driven from the saddle, looking backwards over the driver's shoulder; or they could dismount, swivel the engine unit around and control it as a pedestrian-controlled truck from behind. Under the engine cover were two equal diameter tanks, a fuel tank for petrol and a shorter oil tank. Engine and chain-drive lubrication used a total-loss oil system, controlled by a small pump and needle valve. Info Ref: Lister Auto-Truck - Wikipedia https://en.wikipedia.org/wiki/Lister_Auto-TruckHistoric - Industrial monowheel tractor for moving light loads around factories, railway yards and similar sites.The Lister Auto-Truck - small monowheel tractor Made of steel with three wheels. Powered by a J.A.P single cylinder petrol motor which is Hand Cranked to start.Lister puffing billy, lister, lister auto truck, monowheel tractor

Coat worn by Sister Danson (VFX151507) during the British presence in Japan following the end of the Second World War. About 16,000 Australians served in the British Commonwealth Occupation Forces, including 130 from the Australian General Hospital with whom Sister Danson presumably served. Sister Danson was born in Numurkah and served as Leiutentant with the Heidelberg Military Hospital before embarking for Japan in 1947.This coat is part of a complete uniform set held by the Shepparton RSL. The uniform has representative and historic significance as an example of the style of uniform worn by nursing staff of the Australian General Hospital during the 1940s and into the 1950s. The uniform set has social significance to the Shepparton area, being owned and worn by a serving community member who was born in Numurkah, enlisted in Shepparton and returned to the community in later life.Shin length grey woollen double breasted coat fastened with three buttons on front centre. Interior bakelite or plastic button fastens panels on interior. Two hip-height pockets with folded flap on exterior. Grey fabric belt fastened with a metal buckle; belt is held in place with two fabric loops on either side of the waist. "AUSTRALIA" shoulder flashes on both left and right shoulders; on left arm a blue and brown rectangular colour patch and on the right arm, a blue square patch with embroidered crown and the words "BRITISH COMMONWEALTH FORCES." Epaulettes on either shoulder carry two metal badges signifying a senior Sister and fastened with a metal button. A pin is missing from the base of the epaulette. Interior lined with purple-grey lining; pocket on interior left chest and manufacturer's label at base of neck underneath loop.Shoulder flashes read "AUSTRALIA" and "BRITISH COMMONWEALTH FORCES". Label reads "TAILORS & HABIT/MAKERS/J. RAVENSDALE/& SON/NICHOLAS BLDG./SWANSTON ST MELBOURNE/SISTER DANSON". Buttons read "AUSTRALIAN MILITARY FORCES"second world war, world war ii, medical, wwii, nurse, women

Royal blue rayon knee length dress made of rayon fabric. Bodice is sleeveless with three shoe string straps on each side. Straps have a decorative knot at shoulder joining the three straps. The neckline is an inverted U shape across the front. The bodice is lined with the royal blue rayon fabric. The front of the bodice has two pleated panels running diagonally from the top with the right side overlapping diagonally. The skirt is an A line shape attached to the bodice with two pleats on either side of the front and back. The skirt is lined with brown paper stiffening fabric. A 9cm horizontal band with three pleats is attached above the waist line. On each pleat is a row of decorative buttons (6, 5, 6) made of strings of clear glass beads coiled into a spiral shape. The central back opening has a 36cm zipper.Tag sown inside back of bodice on RHS - Styled by Jeffrey of Melbourne All Rayoncostume, female daywear, dress

Clothing. Infant's cream coloured silk cape with collar and two layers. Semi-circular 180 degrees lined yoke section with round neckline with casing and fold over collar (18 cm). Collar has 9 cm frilled embroidered lace trim with scalloped edges. The cape has two layers both lined with linen fabric. The under layer (110 cm) is edged with 9cm frilled embroidered lace and three horizontal pleats above the hemline. The top layer (52 cm) is edged with 9 cm frilled embroidered lace with a 14 cm panel of embroidered lace across the centre of the cape. The layers create the effect of a long cape with a collar and a shoulder cape. The cape is fastened at the throat with silk fabric ties (8 cm X 50 cm) with fabric frills at the hem.costume, children's, infants cream coloured silk cape

Silver silk, with a jacquard woven floral pattern. Long sleeves have pleated tops, forming a leg-o-mutton sleeve, which gathers in at the elbows, to a narrow fitted sleeve to the wrist. A 4cm wide band of cream satin embroidered and corded lace. Cream cording and lace trims the cuffs, the shoulder/arm hole seam, and two bands on each side of the V shaped cross-over bodice. Metal press-studs fasten the cross over bodice at the waistline. Cream satin with embroidered lace overlay forms a 5cm wide stand-up collar and a centre front panel at neckline. Twelve metal hooks and eyes fasteners fasten the grey cotton front lining of the bodice. The cotton lining of the bodice is part machine, and part hand stitched. Relocated to Clothing Box 176 10.2.2022costume, female, silver silk and lace trimmed bodice.

B&W postcard, 'Gembrook Train Leaving Fern Tree Gully'. The postcard has a photo of a level crossing at Ferntree Gully. The down train has just cleared the crossing and a large group have either just crossed the line or are about to. One woman is carrying an umbrella. A horse-drawn carriage is in the process of crossing the track, obscured by a large shrub. There is a warning sign at the crossing saying 'Railway Crossing, Look out for trains'. Behind the train is a hill with scattered trees. The photo has a patterned, printed frame around it. On the back of the postcard is a written message. 'Am sending ad/vanced birthday/ cards to the/ little girls with/ love. Had a letter from Addie last/ week. A.S. Hunt' and in the address panel, 'Mrs W. Upton/ Wyndham/ Werribee.' A postage stamp has been removed from the card, obscuring the date stamp.

Set of four black and white photographs of interior and equipment of the former ESCo / SECV Wendouree Parade Ballarat A power station sent to the Editor of Trolley Wire - used in the November 1997 issue of Trolley Wire. All photos by Richard Gilbert. Photos taken on 20/8/1971. All photos on Kodak paper. 1144.1 - Looking along building at main distribution switch panel - used on page 24 of trolley wire. 1144.2 - a view across the main steam generator section of the power station - and AC plant - used on page 23. 1144.3 - of the British Thomson Houston rotary converters in used at the time of the photo - used on page 23. 1144.4 - a view from the opposite end of the building shown in 1144.1 - showing the rotary converters are in the front of the photo, AC generators in the middle and foreman's cabin - used on page 22. All have yellow stickers with photo number for magazine printer, and white sticky labels with photo number and words "photo xx same size" written on black ink and photo numbers in pencil from Richard.trams, tramways, trolley wire, esco, power station, ballarat a power station, rotary converters

Set of 3 transparencies taken on 22/11/1962 on Kodak mounts. 1190.1 - No. 7 (bound for North Bendigo) at the Charing Cross stop with No. 19 just left for Quarry Hill. Has the buildings on the south side of High St. in the background, including RACV building. No. 7 has front dash panel ad for Streets ice cream, and roof ads for Ilford Film and an SEC "Cook with Electricity". Passengers are boarding the tram. 1190.2 - Bendigo No. 2 at Charing Cross with fountain in the background and other buildings on the south side of High St. Tram has two SEC roof ads - good side on view - "Electric Cooking - Matchless" and "Switch to Electric Cooking". 1190.3 - Nos. 19, 2 and 7 at Charing cross with a Austin ? motor car. Has buildings on the south side of High St. in the background, along with SEC and Ilford film roof ads.Information written on in black ink and date stamped on purple ink. 1190.1 - "Nos. 19 and 7 at Alexandra Fountain, Charing Cross, Bendigo" 1190.2 - "No. 2 at Alexandra Fountain, Charing Cross, Bendigo" 1190.3 - "Nos. 19, 2 and 7 at Alexandra Fountain, Charing Cross, Bendigo" tramways, trams, bendigo, charing cross, alexandra fountain, tram 2, tram 7, tram 19

Black and white print of a donated negative. Print made 8/1998. Photo of SEC tram no. 31 in Main St, Ballarat East, with destination of "Gardens via Drummond St." Tram has been fitted with dash canopy lighting, but not the large white strip under the lighting. Has small triangles on the panels. Also has a small ad for White Horse whisky. Shows buildings on either side of Main St. and the Caltex service station in the background on Main Road and Bridge St. Photo taken 23-6-1962. Copy made Oct. 2001 for the "gold, Gold GOLD" temporary exhibition - colour laser print onto card, with Velcro dots on rear. Stored in box D1 (Display Box) 02/2003. High Res scan of negative added 17/1/2019.tramways, trams, main st, 31, ballarat, tram 31

Black and White print of an aerial view of Bendigo SECV Bendigo tram 18 at Charing Cross terminus for the Eaglehawk route with another bogie tram and two single truck trams in the background. Trams have dash canopy lights, but no large white strip under the drivers windows. Photo not dated but appears to be at during early 1960's. Tram 18 has White Horse Whiskey ad on front dash panel, SEC Roof ads. Numbers of other trams cannot be determined. All trams have roof ads, including SEC ads and a CASTROL ad. Good view of the fountain and buildings on the north east corner. Has Ezywalkin store, City Club Hotel and other buildings. Shows traffic arrangements for cars to do a right turn from Pall Mall into Mitchell St. On a building in Mitchell St. is an advertisement for "ASTOR Radio"trams, tramways, charing cross, bendigo, mitchell st, aerial views, tram 18

Negative No. N377 and black and white print made by a laser printer (stored in folder) of Ballarat No. 17 at the City Terminus, Sturt St. Tram has destination of "Victoria St." and a White Horse whiskey dash panel advertisement. Has the short tram stop/section pole adjacent to the tram. In the background has the SEC offices, "The Baby Shop", also Crockers and Tunbridge's stores. Note a Conductor can be seen walking across from the SEC offices to the tram. Date of photo on folder - 11/6/1960. Note: Reg Item 858 of Ron Fluck of 31/12/58 shows tram number to the side of the headlight while Wal Jack (Reg. Item 396) of 23/1/61 shows tram fitted with dash canopy lights. Original negative rescanned 24/5/2020 and image file updated.Paper folder that contained the negative had "NR39A" in red ink, "BA4" in pencil, date stamp of "5 Sep 1960" on front, and on rear date stamps "26 Sep 1962" and "6 Oct 1962".trams, tramways, city terminus, sturt st, tram 17

Yields information about a piece of the original equipment from the ESCo Ballarat power station.Colour photograph of the ESCo Wendouree Parade power station - DC face plate starter for one of the rotary converters - DC hand operated drum and multiple lever panel" - see Jan. 1998 issue of Fares Please! for details of the donation and a copy of the photograph as used. Photo taken by Warren Doubleday. Printed on Kodak Paper. Photo taken mid Dec. 1997. Photos of cabinet with doors opened and signs added 2/4/2018. Images .1 - Brookhirst makers plate with Patent Nos. .2 - Machine with doors open .3 - wiring diagram .4 - Brookirst cabinet latch at the bottom of the machine. .5 - Safety sign re opening the doors. .6 - bottom section of cabinet with cable found in machine .7 - top half of machine .8 - similar to .6 .9 - close up of the cable. See January 1998 Fares Please!esco, power station, rotary converters

Set of 15 Digital Images of the aftermath of the sub-station repairs, wiring it up and the installation of the isolating transformer taken between 11/12/2004 and 18/12/2004 .1 - Garry Wood with some concrete for the substation floor .2 - Alan Snowball and Paul Mong laying the floor. .3 - Part of the Switchboard modified to position the new Isolating Transformer .4 - ditto .5 - the Transformer arrives - 15/12/2004 .6 - being positioned in the depot .7 - the manufacturers plate - Illawarra Transformers Wollongong .8 - unpacked .9 - being positioned .10 - In position .11 - the door to no where - the platform across to the store and archives yet to be built .12 - some of the equipment installed but found not to be suitable for the purpose. Was ex an PTC sub .13 - wiring it up .14 - Paul working .15 - the new control panel. trams, tramways, btm, substation, testing, isolating transformer

Utility Pouch was a rectangular web case that was designed to carry three Bren 30 round magazines, or two Anti-tank Rifle Magazines, or Small Arms Ammunition, or a number of Grenades, or a Water Bottle. They were secured with a flap at the top, hinged at the rear, which was fastened with a brass stud fastener on a short web tab.The object is representative of utility pouch/pouch for carrying magazine/ammunition and other items of equipment from the mid to late 20th century. The original design is the 1937 pattern web equipment.Utility Pouch of rectangular web case. Of rectangular parallelepipped shape made of thick and sturdy fabric (canvas). The colour is of a pale shade of green. Front view - Rectangular shape with overlapping closing flap with a press-stud fastener to maintain closed. Left and right views - Both sides are identical. Made of a one piece of fabric forming the base as well ("U" shape) Back view - Rectangular with metal hooks on the middle part for attachment to a belt. There is a Twigg buckle on the top part of the pouch mounted on another piece of canvass ending in a triangular shape. . Bottom view - ‘the fabric forming the base is also forming the sides of the pouch. Top view - closing flap overlapping on 3 sides and forming part of the back of the pouch. Inside view - There is excess fabric from the back panel that forms an additional layer at the base of the pouch.. Handwritten on the back: 3/750133. DELVE S.J.E. On the inside of the closing flap: presence of very faded markings (unreadable)

Purchased from Baptist Community Care Shop in Station Street , Mitcham1980s Wedding dress with vee neckline, bodice coming to a point over waistline. Satin bodice with lace motives re-embroidered with pearl and sequins. Tulle yoke and sleeves with embroidered pattern lace motives and sleeve edge also re-embroidered. Satin bow on shoulders with pearl and sequins embroidering. Back of bodice to point over waistline, buttons down back - eleven self covered buttons over zip fasteners. Back waist finished with large bow at waist. Circular skirt gathered at bodice. Three panels inserted in centre front to 67cm high and 60cm wide. Attached underskirt. Train gathered to back waistline, two widths of material with embroidered lace inserts around hemline. Nine arrangements of embroidered lace flowers inserts over the train coming out of satin petal shaped pouches gathered at top to give an impression of a vase.costume, female ceremonial

Series of five black and white photographs of the Electrical Control room supervisory panel, that was located in Bouverie St and Queensberry St Carlton known as Carlton Control at the time of the implementation late 1964 .1 - General view with the Press standing around. .2 - View of the operators control desk .3 - ditto with the operator at "work" .4 - The room and map without the chair etc. .5 - ditto but a side view. The MMTB News - 1721.4 - Vol. 1, No. 4 - 20 pages, November - December 1964, with a colour photo of the new Supervisory control room at Carlton on the front cover. Has articles on; chairman's message, tramway band, Carlton Control - Supervisory Centre, safe electrical working, Christmas celebrations, the old power control centre, a obituary for H. H. Bell, Remembrance day. Printed on gloss white paper.Items .4 and .5 are stamped on the rear.trams, tramways, carlton, substation, electrical equipment, electrical switching, carlton control

Set of 14 colour prints of Z and Z3 trams being built and equipment at Preston Workshops and Comeng Dandenong, c1979. .1 - Two pantographs of different types laid on top of each other. .2 - ASEA trucks or bogie one marked 115 .3 - Jacobs truck or bogie for a Z3 tram .4 - Z class roof sections stored at Comeng yard .5 - Z class fronts being finished off .6 - Z or Z3 class cars bodies being built at Comeng .7 - Z cab interior showing control panel .8 - Z cab being built .9 - Z class underside or underframe .10 - Interior of Z class being built .11 - ditto .12 - as for .8 .13 - Z3 front .14 - Z class being built. Printed on Kodak Papertrams, tramways, preston workshops, z class, z3 class, pantographs, bogies, tramcar bodies, tramcar manufacture, tramcar trucks, tram 115

Colour postcard, five panels featuring Transporting Art trams: 1 - SW5 726 route 5, by Mental as Anything 2 - Flinders St station with a pipe band marching. 3 - SW5 723 - Bob & Lorraine Jenyns (See also Reg Item 5210) 4 - SW5 829 - The Peace Tram by Megan Evans and Eve Glenn. It was painted in 1986, and overpainted in 1991 by a new work by Lin Onus. 5 - Z 10? - not part of the Transporting Art Project - tram was allocated to Camberwell for some time and is showing route 75. .3 and .4 advised by Russell Jones 16/9/2020. Back has space for name and address, stamp and a message and details of the postcard. Produced by Steve Parish Postcards. Card No. PC323 and a historical note regarding trams on the back. Has "Melbourne Australia" along the bottom edge.trams, tramways, flinders st station, sw5 class, transporting art, tram 723, tram 726, tram 829, tram 10?

Set of four colour prints of trams in Flinders St taken from the Princes Bridge station building deck - 14-5-1985, by an unknown photographer. All printed on Fujicolor Paper with rounded edges. .1 - W2 517 on route 8 northbound in Swanston St with Flinders St station entrance in background. Has a Winfield cigarette advertisement on the side. .2 - W2 453 on route 8, southbound about to cross Princes Bridge with the Anniversary Arch 1984-85 in the background. .3 - W2 605 and W6 994 northbound in Swanston St, with the Flinders St Station concourse buildings in the background. Has a "new black & white 30's" cigarette, Invicta and King Gee work trousers advertisements. .4 - W5 831, south bound on route 72 at the station stop. Has a Reflex copying paper advert on the side panel..3 has in ink on the rear - "W6 994, W2 605 W5 ? Princes Bridge 14.5.85"trams, tramways, flinders st station, princes bridge, swanston st, tram 517, tram 453, tram 994, tram 605, tram 831

Thomas Heath built this shop for his saddlery business around 1875. In 1926 after 58 years operating his saddlery in Bacchus Marsh he retired and the assets of his business were sold in a clearing sale. The building was located close to the current day location of 192 Main Street and has been demolished. Apart from his services in saddlery his premises was known to be a gathering place for much discussion. Heath was known to openly express his political opinions and his saddlery premises was known by many in the community as the 'Parliament'.Small sepia unframed photograph on card with gold border framing photograph. Housed in the album, 'Photographs of Bacchus Marsh and District in 1883 by Stevenson and McNicoll'. The photo is of a double-fronted weatherboard building with a shingle roof. The front gabled section stands directly on street level and is flanked by a picket fence. The door and overhead window and the side window with arched panels may indicate that this was the shop section, with a dwelling to the rear. The recessed side section of the building with a twelve-sectioned window, chimney and a back extension was probably the dwelling used by the family. In the doorway stands the saddler, probably Thomas Heath. To his left is a woman, possibly Mrs Heath, and a much younger woman, possibly a daughter of the Heaths. In front of the two women is a small dog. A hitching rail runs along the front of the workshop. Indicating the type of business Mr Heath ran. On the front: Stevenson & McNicoll. Photo. 108 Elizabeth St. Melbourne. COPIES CAN BE OBTAINED AT ANY TIME. On the back: LIGHT & TRUTH inscribed on a banner surmounted by a representation of the rising sun. Copies of this Portrait can be had at any time by sending the Name and Post Office Money Order or Stamps for the amount of order to STEVENSON & McNICOLL LATE BENSON & STEVENSON, Photographers. 108 Elizabeth Street, MELBOURNE. saddleries, saddlers, thomas heath 1842-1930 saddler, heath family bacchus marsh, stevenson and mcnicoll 1883 photographs of bacchus marsh and district

Worn by Jessie Allan for her marriage to William Thomas Kenny on 13 May 1945 at St Stephens Church, Richmond. They lived in 19 Baldwin Road, Blackburn from 1965. Jessie deceased 1.4.2010. Funeral at St Alfred's Anglican Church, Blackburn South.1945 Cream satin wedding dress with a rouched bodice to a centre panel, high neckline and pointed collar. Bead work on centre panel and edge of bodice, long sleeves to a pointed wrist and beading. Thirty covered buttons down centre back. Skirt cut on cross and three metre train at back.|.2|Champagne coloured Wedding Veil - (approx 6ft in length) - complete with orange blossom 3 1/4' headdress. Headdress is handmade, attached to a wire frame|.3|Cream satin slipper. Machine stitched half in rows. Bow with satin loop and spray of wax orange blossom attached.|.4|Horse shoe shaped wedding item to hang over bride's arm. Rouched satin with ornamental - artificial (wax) orange blossom and buds with 2 mm ribbon to hang over arm. Cream coloured to match wedding dress.|.5|Satin horse shoe, rouched, with satin ribbon handle.|.6|Cream braided horse shoe with gilded wishbone and wax orange spray attached. A bow with long loop to hang on the arm.|.7|Satin Horseshoe Good Luck charm with 'petal' flowers surrounding it, made of cut material - ribbon bow with pearls in centre.|.8|Doll in taxi - Rosy-cheeked, dark hair, blue eyes, dressed in bridal dress with veil, with pearls and 'flowers' decorating the doll. The doll stood across the back seat, under the window. Lavender in base of stand.|.9|Bridal Ring Box - 'Good Luck' horseshoe charm box - in the shape of a prayer book. Cream box with silver motifs printed on.|.10|Groom's Buttonhole of spray of wax orange blossom - 4 flowers and 3 leaves. Cream flowers with yellow stamens - green leaves. 10 Items in total..7 'Wishing you all The Best' 'Good Luckcostume, female ceremonial

Produced by Contour Consultants Australia Pty Ltd on behalf of Dallas Price Homes Pty Ltd as part of the planning process for redevelopment of the former Eltham Shire Office site at 895 Main Road. In 1963 the Shire of Eltham purchased the Shillinglaw property of approximately 2 acres in Main Road, Eltham for the widening of Main Road and as a site for new Council offices. This land, which contained the Shillinglaw Cottage (c1878-80), was the remaining section of the Shillinglaw family holding that originally comprised 30 acres, being Lot 90 of Holloway's 1851 subdivision. Eltham Council intended to demolish this cottage, but through extensive community action it was saved, funds were raised, and it was relocated to the current site adjacent to the Eltham Library. The new Eltham Shire Offices opened in 1965 were designed to ensure retention of the three Italian Cypress trees that were located outside the Shillinglaw Cottage. In 1971 the building was extended at the southern end to provide additional space, including for the Eltham Library and Council's Engineering Department. Renovations were undertaken to the offices during 1987. The Victorian State Government commenced to restructure local government in 1994, which resulted in the establishment of the Shire of Nillumbik and the cessation of the Shire of Eltham. This new Nillumbik Shire Council was headed by government appointed commissioners, who decided in 1995 to put the former Eltham Shire offices on the market. Eventually in June 1996 the property was sold for $1.1 million and the building was subsequently demolished. A planning application for the site was then submitted to Nillumbik Shire Council in September 1996 for construction of a 24-hour service station, convenience store, cafe/takeaway food premises, a retail facility and community facility. There were many objections to this proposed development and in controversial circumstances a planning permit was granted by the Nillumbik Shire Council commissioners. After protracted actions involving a planning panel and a planning advisory committee, established by the Minister for Local Government, the proposal was eventually rejected as not satisfying the requirements of the planning scheme. In December 1997 the purchaser withdrew from the contract of sale, just prior to Council announcing a withdrawal from the contract. While there have been a number of possible development proposals considered by subsequent Nillumbik Shire Councils, this site has remained vacant since July 1996. TIMELINE (Prepared by Jim Connor, Eltham District Historical Society- March 2018- Based on press, council and personal records) June 1996 - Eltham Shire offices sold to Dallas Price Homes for $1.1 million. July 1996 - Shire office building demolished against community's wishes. Council claimed building riddled with asbestos. September 1996 - Planning application submitted to Nillumbik Shire Council to construct on the site a 24 hours Shell service station, convenience store, Hungry Jacks café/takeaway food premises, a retail facility and community facility. 213 objections and petition of over 1400 signatures received. Minister for Planning and Local Government orders an independent investigation into valuation and sale. 9 October 1996 - Permit granted by Nillumbik Shire Council commissioners, in controversial circumstances. A Planning Special Committee consisting of 3 commissioners and 3 community representatives considered 32 community objections. One commissioner declared a potential conflict of interest so only 2 commissioners were able to vote. After hearing all objections, the community representatives moved a foreshadowed motion to refuse a permit. The commissioners then closed the meeting, formerly opened a council meeting (for about a minute) and approved the application. October 1996 - Community members appealed planning decision to Administrative Appeals Tribunal. November 1996 -Minister for Planning and Local Government Robert McClelland calls appeal in and directs MT to refer this 'major policy issue' to the Governor in Council. February 1997 - Planning panel (Dimity Reed and Margaret Pitt) established to consider submissions. March 1997 - New council elected with five councillors. April 1997 - Three of the five new councillors vote to fight Commissioner's decision to grant a permit. April 1997 - Planning panel (Dimity Reed and Margaret Pitt) conducts hearings at Nillumbik Shire offices. June 1997 -Planning panel rejected Dallas Price Homes proposal as being 'totally inappropriate' for the site and recommends the site be rezoned for 'public purposes'. July 1997 - Dallas Price Homes threatened to sue Council and individual councillors. October 1997 - Report released of an Advisory Committee (Paul Jerome) established by the Minister for Planning and Local Government. Committee considered Dallas Price Homes proposal and an alternative concept plan proposal by Council for a gallery, workshop, offices and cinema community-based development. Advisory Committee recommended Dallas Price Homes proposal be rejected as not satisfying the requirements of the planning scheme and recommended further testing of the financial viability of Council's proposal. December 1997 - Dallas Price Homes withdrew from the contract of sale, just prior to Council announcing a withdrawal from the contract, which expired on 28th November and was not renewed by either side, after previously being extended twice pending a decision by the Minister. Council had to pay developer $58,000 for demolition costs. February 1998 - Dallas Price Homes application rejected by Planning and Local Government Minister. October 1998 - Nillumbik Councillors suspended and an Administrator appointed (until March 1999). The demolition of the former Shire of Eltham offices and proposed sale and development driven by the Commissioners for Nillumbik Shire Council brought the community together in substantial protest at the infrigement of ratepayers democratic say in local government and ciommunity assets combined with protests about inappropraite development of Eltham's Gateway. This issue led to the formation of the Eltham Community Action Group which still operates strongly today (2023) on behalf of the community to ensure appropriate development within the community.895 main road, commissioners, dallas price homes, development application, eltham hub, hungry jacks, nillumbik shire council, re-zoning, shell service station, town planning, eltham gateway, eltham gateway action group, eltham shire offices, shillinglaw cottage, shillinglaw farm, shillinglaw trees, jim connor collection

Victorian Institute of Occupational Safety and Health (VIOSH) Australia is the Asia-Pacific centre for teaching and research in occupational health and safety (OHS) and is known as one of Australia's leaders on the field. VIOSH has a global reputation for its innovative approach within the field of OHS management. VIOSH had its first intake of students in 1979. At that time the Institution was known as the Ballarat College of Advanced Education. In 1990 it became known as Ballarat University College, then in 1994 as University of Ballarat. It was 2014 that it became Federation University. VIOSH Australia students are safety managers, senior advisors and experienced OHS professionals. They come from all over Australia and industry. Students are taught active research and enquiry; rather than textbook learning and a one-size fits all approach. VIOSH accepts people into the Graduate Diploma in Occupational Hazard Management who have no undergraduate degree - on the basis of extensive work experience and knowledge. Derek Woolley was a speaker at the Third World Conference on Cooperative Education, held in Melbourne, 21-25 February 1983. This model of education was the basis for the VIOSH program at Ballarat College of Advanced Education. Tables of statistics were included to support the course development. Page 4 has a Bibliography, List of the External Advisory Panel and Seminars and Short Courses attended - 1977-1980. Four A4 pages type written - top section hand written. Two columns per page.viosh, victorian institute of occupational safety and health, third world conference on cooperative education, melbourne, ballarat college of advanced education, external advisory panel, seminars and short courses, occupational hazard management, derek woolley, head of school of engineering, derek viner

In February 2001 the National Council for the Centenary of Federation called upon Australians to nominate someone whom they felt had significantly affected their lives, their community or our country. Thousands of these heroes and quiet achievers were selected. Betty Churcher, a member of the National Council, chaired the Peoplescape Selection Panel. Nominators then made life size, cutout figures to represent their "hero". The sculptures were installed in alphabetical order, on the hill at Parliament House and down to the Federation Mall in Canberra, each with a plaque at its base outlining the individual's achievement. This portrait was painted by Betty Barberis to represent her mother "Dolly" Barton. Dolly raised 12 children, lived through 2 World Wars and the depression. She kept the family dairy farm running whilst her husband was serving in World War 2 whilst still supporting the war effort through the Red Cross and CWA and the church guild. Betty’s great body of work included landscapes, banners, millinery, ceramics, and a bronze sculpture of her husband Vern Barberis who was a fellow schoolteacher and represented Australia as a weightlifter, winning a bronze medal at the Helsinki Olympics in 1952. She was also an art teacher of 22 years. Betty passed away at The Grange, Wodonga on 26 November 2013.This portrait was created by a renowned and highly regarded artist from Northeast Victoria for a national celebration of the centenary of Australian Federation in 2001.A large oil painting depicting a portrait of Dolly Barton, mother of the artist Betty L. Barberis. The painting includes representations of her 12 children, her farming way of life, her commitment to the community and to the war effort. The image was painted on to yellow corflute for exhibition. It has since been covered with perspex to protect the image.betty l. barberis, myrtle ann 'dolly" barton, peoplescape 2001

This is a set of 35 photographs featuring 4th Field Survey Squadron’s newly introduced Survey variant of the Land Rover Perentie light vehicle, at Keswick Barracks, Adelaide SA in 1987. The Land Rover Perentie is a nickname for the Land Rover 110 produced by JRA Limited for the Australian Army, and part manufactured and assembled in Moorebank, New South Wales, during the 1980s and 1990s The name Perentie originates from Land Rover's successful tender to Project Perentie, which was the official Australian Army trial to select new 1 and 2-tonne light vehicles to replace the ageing fleet of Series 2A and 3 Land Rovers. The major differences between the Land Rover Perentie and British Land Rovers were the relocation of the spare wheel to a position under the rear of the load area, a galvanised chassis and the Isuzu engine. The Land Rover Perenties were produced in 4x4 and 6x6 variants and powered by an Isuzu 3.9-litre four-cylinder 4BD1 diesel engine. The Truck, Panel, Lightweight, Survey, FFR, Winch, MC2 model was one of eight 4x4 variants built for the Australian Army. There were 35 vehicles built to satisfy the operational requirements of RA Svy’s units. Source – Wikipedia. See item 6545.9P for related photos of these vehicles.This is a set of 35 photographs featuring 4th Field Survey Squadron’s newly introduced Survey variant of the Land Rover Perentie light truck vehicle, at Keswick Barracks, Adelaide SA in 1987. The black & white photographs are on 35mm negative film and are part of the Army Survey Regiment’s Collection. The photographs were scanned at 96 dpi. .1) to .8) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle features. .9) - Photo, colour, 1986. L to R: unidentified, RQMS - WO2 Peter Symmans, unidentified. .10) to .15) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle features. .16) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle. L to R: WO2 Russ Larsen, SSGT Barry Lutwyche, 2IC Terry Lord, SGT Mick Hogan, unidentified. .17) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle features. .18) & .19) - Photo, black & white, 1987. Loading field trip stores into Land Rover Perentie light truck vehicle. .20) & .21) - Photo, black & white, 1987. L to R: SPR Steve Perks, SGT Mick Hogan loading field trip stores into Land Rover Perentie light truck vehicle. .22) to .25) - Photo, black & white, 1987. L to R: SPR Steve Perks loading field trip stores into Land Rover Perentie light truck vehicle. .26) - Photo, black & white, 1987. CAPT Danny Galbraith loading field trip stores into Land Rover Perentie light truck vehicle. .27) to .31) - Photo, black & white, 1987. Loading field trip stores into Land Rover Perentie light truck vehicle. .32) to .34) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle – broken transfer case lever. .35) - Photo, black & white, 1987. Land Rover Perentie light truck vehicle’s Isuzu 3.9-litre four-cylinder 4BD1 diesel engine..1P to .35P – There are no personnel identified. ‘PERENTI MOTOR VEHICLES JUL 87’ annotated on negatives sleeve.royal australian survey corps, rasvy, 4 fd svy sqn

This is a set of nine photographs featuring 4th Field Survey Squadron’s newly introduced Survey variant of the Land Rover Perentie light truck vehicle on a field trip in SA, in 1987. The Land Rover Perentie is a nickname for the Land Rover 110 produced by JRA Limited for the Australian Army, and part manufactured and assembled in Moorebank, New South Wales, during the 1980s and 1990s The name Perentie originates from Land Rover's successful tender to Project Perentie, which was the official Australian Army trial to select new 1 and 2-tonne light vehicles to replace the ageing fleet of Series 2A and 3 Land Rovers. The major differences between the Land Rover Perentie and British Land Rovers were the relocation of the spare wheel to a position under the rear of the load area, a galvanised chassis and the Isuzu engine. The Land Rover Perenties were produced in 4x4 and 6x6 variants and powered by an Isuzu 3.9-litre four-cylinder 4BD1 diesel engine. The Truck, Panel, Lightweight, Survey, FFR, Winch, MC2 model was one of eight 4x4 variants built for the Australian Army. There were 35 Vehicles built to satisfy the operational requirements of RA Svy’s units. Source – Wikipedia. See item 6544.35P for related photos of these vehicles.This is a set of 35 photographs featuring 4th Field Survey Squadron’s newly introduced Survey variant of the Land Rover Perentie light truck vehicle, at Keswick Barracks, Adelaide SA in 1987. The black & white photograThis is a set of nine photographs featuring 4th Field Survey Squadron’s newly introduced Survey variant of the Land Rover Perentie light truck vehicle on a field trip in SA, in 1987. The black & white photographs are on 35mm negative film and are part of the Army Survey Regiment’s Collection. The photographs were scanned at 96 dpi. .1) - Photo, black & white, 1987. Perentie Land Rover with trailer parked outside unknown motel in SA. .2) & .3) - Photo, black & white, 1987. Field trip featuring Perentie Land Rover. .4) - Photo, black & white, 1987. Field trip featuring Perentie Land Rover. Series 3 Land Rover parked behind. Unidentified personnel. .5) & .6) - Photo, black & white, 1987. Field trip featuring Perentie Land Rover. Unidentified personnel. .7) & .8) - Photo, black & white, 1987. Field trip featuring Perentie Land Rover. Typical sandy 4WD track on fence line. .9) - Photo, black & white, 1987. Field trip featuring Perentie Land Rover. Probable gas extraction facility..1P to .9P – There are no personnel identified. ‘PERENTI MOTOR VEHICLES JUL 87’ annotated on negatives sleeve.tified. royal australian survey corps, rasvy, 4 fd svy sqn

Walter Withers (1854-1914) was born in Handsworth, Warwickshire, England. He migrated to Australia in 1882 and in time was to become one of the country's most famous painters. In 1887/8 he spent a year in London and Paris during which time he married Fanny Flinn. When he returned to Melbourne he was engaged by publishers doing black and white illustrations. In the late 1880's he became associated with artists who formed the renowned "Heidelberg School" and in 1890 moved to "Charterisville" at Eaglemont. He lived in the Heidelberg area until 1903 when he purchased a house on two and a half acres (one hectare) at the corner of Brougham and Bolton Streets, Eltham. He had long been attracted to the Eltham area, but needed access to Melbourne for his painting classes. The extension of the railway in 1901 made the move possible. He remained in Eltham until his death and is buried at nearby St Helena. Many of his important paintings were painted during these later years. There are important collections at the National Gallery of Victoria and the Geelong Art Gallery. His Eltham house remains and his name is honoured by a small park at the corner of Bible and Arthur Streets. Source: Information panel produced for Heritage Display exhibition by EDHS 1990.This photo forms part of a collection of photographs gathered by the Shire of Eltham for their centenary project book,"Pioneers and Painters: 100 years of the Shire of Eltham" by Alan Marshall (1971). The collection of over 500 images is held in partnership between Eltham District Historical Society and Yarra Plenty Regional Library (Eltham Library) and is now formally known as the 'The Shire of Eltham Pioneers Photograph Collection.' It is significant in being the first community sourced collection representing the places and people of the Shire's first one hundred years.Digital image 4 x 5 inch B&W Neg (duplicate of original)eltham local characters, pioneers and painters, sepp, shire of eltham pioneers photograph collection, walter withers, eltham, southernwood