Ore bearing rock brought out of the mine was crushed at the battery by heavy metal stampers and the fine material passed over copper pates coated with mercury. Gold particles would combine with the mercury forming an amalgam which was then scrapped off the copper plates and put into the amalgam bucket ready for retorting too extract the gold. The amalgam of mercury and gold was placed into the retort which was heated to evaporate the mercury. The mercury cooled as it ran down the pipe which was recovered to be reused leaving the gold behind. The gold would later be put into a crucible and heated to burn of impurities and the molten pure gold poured into an ingot.A heavy cast iron bucket 20 centimetres high, 16 centimetres in diameter at its base and 22 centimetres diameter at the top. It has a spout five centimetres wide protruding two centimetres. There is a handle which is a semi- circular shape 19 centimetre wide extending 14 centimetres above the bucket The inside of the bucket has an enamel coating. amalgam bucket, bendigo gold, gold retort

Medal issued to commemorate the 50th jubilee of the Town of Kew. It names J.F. McCrea as Mayor. John Falding McCrea was Mayor of Kew 1910-11. Kew was proclaimed a municipality on 22 December 1860, seceding from the Boroondara Road Board District, then comprising Kew, Hawthorn and Camberwell. It was proclaimed a town on 8 December 1910, the year this medal was issued, and a city on 10 March 1921. On 22 June 1994 Kew city was united with Camberwell and Hawthorn cities to form Boroondara city.Mint gilt medal with original ribbon.Kew Jubilee medal in the shape of a Maltese cross. Gilded bronze with attached original red, white and blue cloth ribbon. On the front is the Coat of Arms of the Town of Kew and an inscription: ‘Town of Kew. To Commemorate Its Jubilee 1910’. On the reverse is inscribed 'Kew Jubilee 1860-1910. Cr J.F. McCrae J.P. Mayor'. The medal was also issued in bronze.Obverse description Shield of six wheat-sheafs above motto CRESCO on ribbon; above shield is the Royal coat of arms with lion and unicorn supporters and, on ribbon DIEU ET MIN DROIT; on arms of cross top, TOWN / OF, bottom, KEW, left TO COMMEM / -ORATE, right, ITS JUBILEE / 1910 Reverse description Within line circle set at centre of cross shaped flan, CR. J.F. McCREA / J.P. / MAYOR on arms of cross, top, KEW bottom, JUBILEE, left 1860, right, 1910jubilee - kew (vic), commemorative medals - kew (vic), australian commemorative medals

The telescope is original to the Wilsons Promontory Lightstation and was provided by the Department of Shipping and Transport in about 1900. The device magnifies images of distant objects through its curved interior mirrors, and lightkeepers used this telescope to monitor and record the names of ships, the time they passed, and their direction, as well as read meanings of flags and other visual signals communicated by vessels. The telescope is similar to Cape Nelson’s two metre long telescope, which is included in the VHR registration for the Cape Nelson Lightstation. It is particularly important for its good condition, completeness and confirmed provenance and has first level contributory significance to the cultural heritage values of the lightstation..1 Brass telescope, cylindrical tube shape with mobile interfolding sections. Middle section of tube has been covered with textile or leather and painted black. Narrow plaited rope fixed as a border to this section is also painted black. .2. The telescope is attached by a brass fitting to a wooden tripod on a three legged triangular ply wood base with three castors.

Kerosene lamps were used as a main source of lighting throughout Australia prior to the supply of domestic electrical services. This was obviously later in many rural areas. This lamp was used in the home of Mrs. Laura Flower nee Sommer wife of Mr. Stanley Flower of Wodonga.This lamp is representative of the lamps used throughout Australia prior to the introduction of domestic electricity supplies. It was used in the home of a Wodonga resident.This item has a cast iron base in a pyramidal shape with the four sides having an identical leaf and flower design. A piece of brass attaches the base to a clear glass bowl. The bowl contains a white wick. The brass wick holder has an external knob for regulating the light intensity. There is more brass between the bowl and the mantle which is made of plain glass.Inside the base of the lamp: an Rd No which is uncleardomestic appliances, kerosene lamp

The design for the badges was chosen from competition entrants by school children from the nearby area. The badges were worn by volunteer tour guides.Two (2) tour guide badges, B&W, with the writing: Darebin Parklands Tour Guides. Round in shape, made from plastic with metal fastening. This item and all other Darebin Parklands Association archival material is now held by State Library Victoria (Accession No: YMS 13746). Please contact State Library Victoria if access is required.tour guide, badge

Black metal lamp with handle attached to top. Lamp is a rectangular shape with small curved section on top. Top of lamp hinged to allow access to inside section. No glass on side panels. Small cylindrical section in centre of inside section of lamp presumably to hold light source (candle?) Further research required re operation and provenance of lamp.gold mining, mining equipment, lamp

Viola Annie McVicars (1911–1990) was born in Korumburra on 29 April 1911. At the age of 21, she married William John Ayling (1909–1995). After their marriage in 1932, they moved to Kew, initially to 81 Tennyson Street, and later to 180 Pakington Street. A professional tailoress, Viola Ayling was also a talented amateur potter, creating her ceramics at her home in Pakington Street, where she had an internal studio and a handmade, wood-fired brick kiln in her backyard. Following her death in 1990, her studio pottery passed to her daughter, and following the daughter’s death, to her granddaughter. This piece of glazed earthenware is part of a collection of 15 functional and decorative ceramic items donated by Viola’s granddaughter to the collection in 2024.A pair of handmade bookends, expertly potted and glazed. The style is representative of Australian ceramic design of the period, particularly that employed by Klytie Pate.Pair of hand moulded abstract ceramic wall sculptures with holes and marks of the original wires on the reverse. The front and back are glazed while the interior has been left unglazed. The free-form shapes resemble waves which were initially covered with a white glaze which was then overgrazed in a semi-transparent turquoise glaze. Both pieces are signed by the artist on the reverse.Signature to bases: "V. Ayling"ceramics, pakington street -- kew (vic.), viola annie mcvicars, viola annie ayling, ceramic sculptures

Pamphlet - folded and cut in the shape of a Melbourne W class tram with arched advertising windows, for the marketing of an auction of "The Cromwell Building" - Wednesday 19 August 2009 (year based on calendar search). Gives details of the building and site, and agent contact details. Has photos of the building on the corner of Elizabeth and Bourke Streets. Agents Alexander Robertson and Colliers Jardine.trams, tramways, auctions, real estate, advertisements, bourke st, elizabeth st

A small timber church, containing an entrance area, congregation area, vestry and a small store room. The main part of the church is rectangular, but the smaller rooms give the building a 'T' shape. The roof is 'A' framed and is corrugated iron. There are three crosses on the roof; one on the entrance and two on the main building; one on the front and one at the rear. There is a bell in the yard. Built in 1895moe, church, old gippstown, west gippsland, gippsland, gippsland heritage park, goldfields, coal mine, victorian era, historical village, church of england, holy trinity anglican church, rev. c.j. chambers, latrobe valley, old gippsland heritage park, latrobe city council

This will be for an Armstrong Siddeley Cheetah Engine. They were produced between 1935 - 1948. For example they were used on AVRO ANSON AIRCRAFT.This propellor is crafted from eight layers of timber. The hub is round. It has eight holes for mounting bolts. The bolt holes are approx 13mm diameter. The two tips are aerofoil shape and squared off. Tip ends are 9.5 cm wide. On both sides of the hub are segments cut out. Approx 20 cm wide and 5 cm high.There is a brass plaque attached to the hub. Inscribed on it is; “DWG No. 2 3931/7. D.7. 33'. P.6.95' CHEETAH X LH”aircraft engines, avro ansons, propellor

The Yellow-billed spoonbill is a waterbird which can be commonly seen wading through shallow waters. This particular variety of Spoonbill is found across Australia, mostly in the northern and well-watered inland areas. It resides in freshwater wetlands, dams, lagoons and swamps. The species feeds on mainly aquatic insects and larvae. The bill has vibration detectors called papillae inside the spoon which enables the bird to feel the vibrations of its prey in murky water. These birds nest in the colonies of other birds like the Ibises and Royal Spoonbills. They live in high forks of trees over water or in reed beds. This specimen is part of a collection of almost 200 animal specimens that were originally acquired as skins from various institutions across Australia, including the Australian Museum in Sydney and the National Museum of Victoria (known as Museums Victoria since 1983), as well as individuals such as amateur anthropologist Reynell Eveleigh Johns between 1860-1880. These skins were then mounted by members of the Burke Museum Committee and put-on display in the formal space of the Museum’s original exhibition hall where they continue to be on display. This display of taxidermy mounts initially served to instruct visitors to the Burke Museum of the natural world around them, today it serves as an insight into the collecting habits of the 19th century.This specimen is part of a significant and rare taxidermy mount collection in the Burke Museum. This collection is scientifically and culturally important for reminding us of how science continues to shape our understanding of the modern world. They demonstrate a capacity to hold evidence of how Australia’s fauna history existed in the past and are potentially important for future environmental research. This collection continues to be on display in the Museum and has become a key part to interpreting the collecting habits of the 19th century.The Yellow-billed spoonbill specimen is a large taxidermy of mainly white colouring. The bill is a large and unique spoon shape and is yellow. The long gangly legs and the skin on the face are also yellow. The eyes are made from a black and yellow glass and the bird is stylized standing on a square wooden platform. A paper identification tag is tied to the bird's upper left leg.6c. / [illegible] / Spoonbill / taxidermy mount, taxidermy, animalia, burke museum, beechworth, australian museum, skin, reynell eveleigh johns, bird, australian birds, spoonbill, yellow-billed spoonbill, yellow billed spoonbill, waterbird

Distinguish Flying Cross medal awarded to John Hudson WILKINSON 400444 born 18/2/1914 at Rutherglen. He was a Pharmaceutical Chemist prior to enlisting in the RAAF on 2/9/1940 He was reporting missing during air operations over East Prussia and later presumed to have lost his life on 30/8/1944 Awarded the Distinguished Flying Cross - citation reads Pilot Officer Wilkinson is an air gunner of great ability and determination. He has taken part in a large number of operational sorties many of which have been against some of German's most heavily defended targets. On one occasion in March 1944 when engaged n an attack on Stuttgart a Junkers 88 attacked his aircraft five times but Pilot Officer Wilkinson by his accurate directions to his captain and coolly aimed return fire drove ff the enemy aircraft in a badly damaged condition. At all times his unwavering devotion to duty and constant alertness have inspired confidence in his crew. The Distinguished Flying Cross (DFC) is the third-level military decoration awarded to officers, and since 1993 to other ranks, of the United Kingdom's Royal Air Force and other services, and formerly to officers of other Commonwealth countries, for "an act or acts of valour, courage or devotion to duty whilst flying in active operations against the enemy"Black case which opens out from right side. The top affixed by two side hinges on the left and push in pin on the right side. Inside case the top is lined in satin fabric imprinted with a black crest and the base is lined in felt containing a silver metal medal in the shape of a cross attached to a purple and while diagonally striped ribbon.On Top - DFC impressed in gold colour paint. Inside Top - Royal Mint Medal inscriptions -400444 Flt Lt Wilkinson Stuttgart 1944 pilot officer john hudson wilkinson, dfc, ww2, raaf, kia

items issued to John Raymond Bruns VX88627, refer Cat No 5592 for his service history. The RSL badge has a clip over a top crown with the numbers "88" meaning a financial member for 1998.1) Badge, Returned from Active Service, brass depicts a Rising Sun, crown, wings, anchor and boomerang, rear has two lugs and stamped. .2) Badge RSL Membership, shows three central figures on a plaque style shape, white, gold, red & blue colours, rear has one lug with a pin through, rear is stamped..1) On rear, "A 32763" .2) On rear, "48617", "Badge remains property of the league"badges, rsl, ras, 2nd 38th

Items belonged to Wayne William Forbes No 3176337 RAE. Refer Cat No 754 for service history also 2586. Part of an extensive collection including his fathers..1) Wooden stained shield shaped plaque with a Rising Sun badge mounted centre. The badge has been bent into a curved shape. .2) Wooden stained shield shaped plaque with a Royal Australian Engineer plaque centre. Under is a gold coloured scroll with 1 Field Squadron Group RAE SVN. At the top is a small brass plaque..2) Presented to SPR W FORBESmilitary history - army, plaques, rae

A moulding plane is a specialised plane used for making the complex shapes found in wooden mouldings that are used to decorate furniture or other wooden object. Traditionally, moulding planes were blocks of wear resistant hardwood, often beech or maple, which were worked to the shape of the intended moulding. The blade, or iron was likewise formed to the intended moulding profile and secured in the body of the plane with a wooden wedge. A traditional cabinetmakers shop might have many, perhaps hundreds, of moulding planes for the full range of work to be performed. Large crown mouldings required planes of six or more inches in width, which demanded great strength to push and often had additional peg handles on the sides, allowing the craftsman's apprentice or other worker to pull the plane ahead of the master who guided it. The maker of this plane is unknown but probably made in London early to mid 18th century. There are many of his tools including decorative moulding planes of all sizes and designs for sale around the world with no makers marks however moulding planes from this era are well sought after by collectors of vintage tools.A vintage tool made by an unknown maker, this item was made commercially for firms and individuals that worked in wood and needed a tool that could produce a ornamental finish to timber. The tool was used before routers and spindle moulders came into use after World War ll, a time when to produce a decorative moulding for a piece of furniture, door trims etc or other items had to be accomplished using hand tools and in particular one of these types of planes. These profiled planes came in various shapes and sizes to achieve a decorative finish. A significant tool from the early to mid 18th century that today is quite rare and sought after by collectors. It gives us a snapshot of how furniture and other decorative finishes were created on timber by the use of hand tools. Tools that were themselves hand made shows the craftsmanship used during this time not only to make a tool such as the subject item but also the craftsmanship needed to produce a decorative finish that was needed to be made for any timber item.Wood Moulding Plane Rabbet typeMarked J Heath on end, (no makers mark)flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, plane moulding, moulding plane, plane, j heath, ames

A single rollover kerb has just been laid on western side cut into the embankment. At the crest of the hill on right in front of the Ford Laser is a fire hyrdant. This photo was processed at the same time as image EDHS_07261 of roadworks in Sackville Street about 200 m away which has been dated as c.1983 (between Sep 1982 and May 1983). The paling fence on the left has a change of angle just before the crest of the hill then flattens. More recent Google Streetviews show the same fence and shape and in more recent times a new fence but same shape. Google Streetview for Jan 2008 indicates a more recent road widening and new profile kerb and channel. The embankment was further cut away and the footpath that was adjacent to the fence lowered to road level. The fire hydrant that was on the right hand side has been relocated to the left next to the footpath. Significantly more electrical wires are now strung on the telephone poles. In 2017 Bolton Street was again upgraded. The fire hyrdrant was then relocated to another (unknown) location.1983, footpaths and gutters, road construction, road drainage, road sealing, bolton street, eltham, sackville street

This copper nail, sometimes known as a ‘Dumpy Bolt’ or spike, was salvaged from the hull of the wreck of the “George III”. It dates back to at least 1810. It was found by an abalone diver on the south east coast of Tasmania. The nail would have been used to hold the layers of the ship’s keel frame and the planking together. The nail has been passed from the abalone diver to an interested business man on a trip to the south of Hobart, on again to the business man’s close friend who then donated it to Flagstaff Hill Maritime Village. The metal of nails such as this one, after being in the sea for a long time, become affected by the natural reaction of the sea water, causing it to degenerate and thin, and the stress from the force of the sea over the years alters its shape. Iron nails had been used on ships previously, but they quickly corroded in the salt; ships needed regular, costly and time-consuming maintenance to replace the iron nails. Towards the end of the 18th century the British Navy trialled the use of copper nails, finding them to be very successful. Merchant ships began to adopt this process in the early 19th century, although it made ship building very expensive and was more often used for ships such as the “George III” that sailed on long voyages. The three masted sailing ship “George III” was a convict transport ship built in Deptford, England, in 1810. On 14th December 1834 she left Woolwich, England, bound for Hobart Town, Van Diemen’s Land (Tasmania), under Captain William Hall Moxey. She was carrying 220 male convicts plus crew, guards and their families, totalling 294 persons (another 2 were during the voyage). Amongst the cargo were military stores including several copper drums of gun powder. On 27th January 1835 the “George III” was near the Equator, about half way into her journey. A fire broke out and the gun powder was in danger of explosion, threatening the whole ship. Two convicts braved the heat and smoke, entered the store and seized the gun powder drums, suffering burns for their efforts but saving a probable disaster. The fire destroyed some of the provisions and food was scarce. Many became ill with scurvy and some died during the journey. Nearing the end of their journey on 10th April 1835 the “George III” was headed through the D'Entrecasteaux Channel, south east Tasmania, between the mainland and Bruny Island. She was sailing in the moonlit night to hasten her arrival in port due to the great number of sick on board. She struck uncharted rocks, known only to the local whalers, between Actaeon Reef and Southport Lagoon and within hours began to break up. The ship’s boats were used to first rescue the women and children. Firearms were used to help quell the panic of the convicts below decks and some were killed by the shots. Many convicts, including the sick, were drowned. In all, 133 lives were lost including 5 of the crew, guards and their families. It was the third worst shipping disaster in Tasmanian waters. A monument in honour of the prisoners who perished in the “George III” has been erected, noting the date of the wreck as “Friday 10th April 1835.” (NOTE: there are a few differences between sources regarding dates of the shipwreck, some saying March and others April 1835. There are also differences in the figures of those on board and the number of lives lost.) The copper nail is significant as an example of sailing ship construction; fasteners used in the early 19th century on ships carrying convicts to Australia. The nail is also significant for its association with the ship “George III”. The “George III” is registered on the Australian National Shipwreck Database, ID 7195 as an Historic Shipwreck. She is the third worst shipwreck in Tasmanian waters. She is also associated with Early Australian History and the transportation of convicts to Australia. The incident of the fire on board and the bravery of the convicts in making the gun powder safe is an example of the social character of the people in early Tasmanian colonisation. Copper nail (also called a Dumpy bolt or spike) from the convict ship George III, wrecked in 1835. Nail is long, bent in an ‘L’ shape about 3/5ths along, tapering from both ends to the bend. Both ends are flat and do not taper to a point, nor have a thread. The shorter end has been polished, showing bright copper. There is pitting along the nail and virdigris is evident on the longer, unpolished end. The nail is displayed with the longer section resting on a wooden board between two ‘U’ shaped uprights, the shorter section upright. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, george iii, ship construction, ship nail, 1835 shipwreck, 19th century shipwreck, william moxey, d'entrecasteaux channel, convict transportation, copper nail, dumpy bolt, spike, keel nail

A mortise axe is a specialist axe designed for hewing sills and notches in joints. The axe has a long, narrow head, making it easier to work on large logs. The shape enables the user to hew a long way down into the notch, where otherwise a chisel would be used. This tool has one blade, which may be pushed, swung or struck with a mallet. Others, have two, one of which is used for separating the fibres, and the other for levering out the waste.This is an example of a common woodworking tool used by the early settlers in the Orbost district.A long wooden handled axe used to cut mortises in posts for post and rail fences. The blade is made of iron and is quite long.axe mortise-axe fencing timber farm-tool

Ground sheets such as this were typically used as rain protection by German troops. Two or more zeltbahn (ground sheets) could be attached together via the button holes to form a tent for two or more people. Some models of ground sheets, particularly those which are triangular in shape, could also be fashioned into personal raincoats worn by soldiers. Grounds sheets have also been known to have been used to wrap deceased bodies in prioir to burial.This groundsheet, despite a lack of clear provenance, is a representative example of the types of ground sheets used by the German forces during wartime. The zeltbahn (ground sheet) also has social significance in that they were known to have been used to wrap deceased bodies in prior to burial.Large square sheet constructed of biege/brown coloured water resistant material. 67mm hem folded over and sewn along all edges with brown stitching. Metal buttons are spaced at 200mm intervals along parallel edges, next to a button hole which can be used to attach to another ground sheet. Four corners bear a large round eyelet in silver-coloured metal in between three smaller eyelets; two of four corners have short lengths of brown cord attached to these eyelets. One corner has only two smaller eyelets surrounding the larger.Printed in black ink in the centre of the sheet is the incriptions "OVS 1298."ground sheet, zeltbahn, tent, raincoat, german

Kelly Slater is contemporary surfing's dominant competitive presence and a truly inspirational surfer. By the end of 2009 Kelly had won a record 9 professional World Surfing Championships. This surfboard is one of Kelly's from 1996 shaped by world renowmed shaper Al Merick from Channel Island Surfboards, Santa Barbara, California. This board was ridden by Kelly in Indonesia in 1996 and featured on the cover of Surfer Magazine in November 1996 in a sequence shot at speed reef Grajagan.This surfboard was ridden by Kelly Slater throughout 1996 and most famously featured on the cover of Surfer Magazine. In 1996 Kelly Slater was at the peak of his surfing powers. During this year he won his 4th World Professional Surfing championship equalling the record held by Australian Mark Richards. This surfboard has international significance and represents a number of innovative design trends during this period.Kelly Slater surfboard shaped by Al Merrick (Channel Island Surfboards)in 1996. The surfboard is a three fin, 6' 6" rounded pin, colour yellow. The board, with Kelly riding it, featured on the cover of Surfer magazine in November 1996 in a sequence, shot in Indonesia at speed reef Grajagan.Deck - Quiksilver, Al Merrick logo Bottom - 'Glasscraft by Bob Haakenson Santa Barbara' behind last fin. Al Merrick logo 63921A Kelly on stringerkelly slater, al merrick, surfer magazine, grajagan, channel island surfboards, quiksilver

The former Ballarat Gaol was commenced in 1856 and completed in 1862, This view looks up Lydiard Street South, and was taken before the Ballarat Courthouse was built south of the gaol in 1868. The wall was built from quarried basalt with local bricks. A system of burning the lime mortar between the joints and the shape of the wall meant it had a high degree of stability. From 1870 on more buildings were constructed and these became the School of Mines and Industries Ballarat. The Gaol closed in 1965. This image shows the Ballarat Gaol c. 1861 giving us an understanding of what the site looked like before all the changes that have occurred over the years since the gaol closed and other organisations have had the site. Black and white image showing the former Ballarat Gaol from Lydiard Street South.Label on underneath photograph: The Ballarat Gaol, c.1861 - This view looks up Lydiard Street towards our present school entrance. The gaol buildings remain unchanged . Note that the Court House, now S.M.B's Elec. classrooms, has not yet been built on the right hand side of the gaol.ballarat gaol, ballarat school of mines, gaol, m113, lydiard street, courthouse, lime mortar, lydiard street south

This brass bell bracket has been carefully shaped to fit around the shape of a bell. Its fitting allows it to swing freely. The bracket allows the bell to be fixed to a horizontal surface such as a s wooden frame, post or base. It may have been portable or fixed to a counter, desk or table. The bell may have been used to sound the time, to draw attention to an event such as a church surface, to signal a time to start or stop, or even as a percussion instrument.This metal bell bracket appears to be handmade and may have been used as a portable signal for a school or public meeting. It could have been used on a ship to signal the watch or the time.Bell bracket; the brass, bracket is bell-shaped with a removable hinged section across the top where the bell swung. The base is composed of a curved and shaped base stand. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, bell bracket, bell stand, bell frame, swinging bell, portable bell, bell ringing, signal

shoulders when pulling a wagon or plough. The collar often supports and pads a pair of curved metal or wooden pieces, called hames, to which the traces of the harness are attached. The collar allows the horse to use its full strength when pulling, essentially enabling the animal to push forward with its hindquarters into the collar. It is a padded appliance that conforms well to the shape of the horse's body and is constructed so that at all points of contact with the body of the horse it avoids the air passage.The early settlers in Moorabbin Shire depended on the draught horse to pull the equipment need to plough the fields, grade the roads, pull their wagons of produce and small carts for transport as they developed the land after the Henry Dendy Special Survey 1841 Horse Collar small 20thCearly settlers, pioneers, draught horse, ploughs, farm equipment, saddles, leatherwork, blacksmiths, cheltenham, sandringham, city of moorabbin, county of bourke, moorabbin roads board, parish of moorabbin, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman stephen, highett william, ormond francis, maynard dennis, market gardeners, horse drawn wagons, plateway, vegetables, poultry farms, dairy farms,

In the 17th century young girls were taught embroidery as a necessary skill for marriage, this also helped them make very beautiful handbags. By the late 18th century, fashions in Europe were moving towards a slender shape and women wanted purses that would not be bulky or untidy in appearance, so reticules were designed. Reticules were made of fine fabrics like silk and velvet, with wrist strap often decorated with pearls, sequins, beads and embroidery. A lady's black velvet, silk lined, evening bag with draw-string and hand made tassels. The bag is decorated with beads in a floral designmoorabbin, brighton, early settlers, pioneers, cheltenham, craft work, dressmaking

Max Havelaar: Or the Coffee Auctions of the Dutch Trading Company (Dutch: Max Havelaar, of de koffi-veilingen der Nederlandsche Handel-Maatschappy) is an 1860 novel by Multatuli (the pen name of Eduard Douwes Dekker), which played a key role in shaping and modifying Dutch colonial policy in the Dutch East Indies in the nineteenth and early twentieth century. In the novel, the protagonist, Max Havelaar, tries to battle against a corrupt government system in Java, which was then a Dutch colony.The novel was central to the growing public awareness of corruption and exploitation by the Dutch colonial master in the East Indies. Published in 1860 it is considered the highpoint of Dutch literature in the 19th century. Hard cover book by Dr.J.van den Bergh published in 1920 containing a newly selected collection of extracts of the publication "Ideen" (Ideas) by Multatuli. The book is in 2 parts and contains about 600 pages. There are a number of drawings as illustrations.The illustrator is Anton van der Valk.

An Adze is versatile cutting tool similar to an axe but with the sharp cutting edge perpendicular to the handle rather than parallel. The wooden handle of this adze is shaped like an axe handle and the blade also has a slight curve. They are used for smoothing or carving wood such as sleepers An adz, with its long handle, cuts with the grain, and the nature of the chips is different from an axe. While they have a similar shape, they should never be confused with a hoe used or mattock for agriculture and horticulture.Carpenter's adze or cutting adze The tapered eye in the adze and tapered handle end forces the head to tighten when swung; but enables removal of the head for sharpeningtimber tools

Geelong is famous for its bollards. Created by local artist Jan Mitchell, the colourful bollards spot the foreshore, representing a fascinating and fun chronicle of the city’s past. Few people know that Mitchell planned for a flock of sheep to be part of her public art project. The wool industry is an important part of Geelong’s history, so Mitchell thought what better than a flock of sheep to welcome people to the city. The flock (and a Shepard) were to be placed out on the Melbourne-Geelong highway, near Lara, to welcome travellers to the city. The sheep would then be scattered along the road as a wayfinding signal to bring people to Geelong. When traffic authorities heard the plan for bollard sheep along the road, they squashed the project as a potential distraction for drivers. Another flock was also suggested for the hills of the eastern gardens, overlooking the bay. This was also disapproved; so Mitchell only ever partially completed four sheep bollards. The bollards are remnants of Jan Mitchell’s flock of sheep. The sheep also show the evolution of one of Geelong’s most iconic art installations. From the first sheep showing the raw timber of the old Yarra Street pier, to the sheep without a face, through to the completed sheep, it is possible to trace Mitchell’s process in the preparation of the bollards. The lost bollards form part of the National Wool Museum’s unique collection. The first bollard is the least complete, still in its original timber colour. From the central cylindrical shape, an additional wedge protrudes. This unpainted wedge forms what would have been the face of the sheep, with an ear present on either side that would have been painted white. Presently they are a bare metal. No legs are present on this bollard. The second and third bollard are completed to a similar level. They have a central cylindrical shape with an additional wedge protruding from the front of the timber. This wedge forms what would have been the face of the sheep, with an ear present on either side. The face and ears have been painted white but the finer details such as the eyes have not been added. These bollards bodies have also been painted white and have their legs attached. The legs are thin metal cylinders, approximately 50mm in diameter and 500mm long. The fourth bollard Is complete. It has the same central cylindrical shape with an additional wedge protruding from the front of the timber. This wedge forms the completed face of the sheep, with an ear present on either side that has been painted white. The face also features completed painted eyes. This bollard has its legs attached. The legs are thin metal cylinders, approximately 50mm in diameter and 500mm long. geelong, bollards, geelong's bollards, jan mitchell

The Gang-gang Cockatoo can be found throughout much of south-eastern Australia. They reside in mountainous forests and open woodlands, often in small groups or larger flocks at sources of food and water. They eat mainly seeds from native trees and shrubs along with wattles, eucalypts and hawthorns. The Gang-gang Cockatoo is also known to incorporate berries, nuts, fruits and insects to their diet. The sound made by this type of Cockatoo is often described as a rasping screech which resembles the sound of a rusty hinge being moved.This type of call is made when the bird is in flight. These birds also fond of attention and can pick their own feathers if they are bored. The name "gang gang" derives from a New South Wales Aboriginal language, either the Ngunnawal or Wiradjuri. This specimen is part of a collection of almost 200 animal specimens that were originally acquired as skins from various institutions across Australia, including the Australian Museum in Sydney and the National Museum of Victoria (known as Museums Victoria since 1983), as well as individuals such as amateur anthropologist Reynell Eveleigh Johns between 1860-1880. These skins were then mounted by members of the Burke Museum Committee and put-on display in the formal space of the Museum’s original exhibition hall where they continue to be on display. This display of taxidermy mounts initially served to instruct visitors to the Burke Museum of the natural world around them, today it serves as an insight into the collecting habits of the 19th century.This specimen is part of a significant and rare taxidermy mount collection in the Burke Museum. This collection is scientifically and culturally important for reminding us of how science continues to shape our understanding of the modern world. They demonstrate a capacity to hold evidence of how Australia’s fauna history existed in the past and are potentially important for future environmental research. This collection continues to be on display in the Museum and has become a key part to interpreting the collecting habits of the 19th century.The male Gang Gang Cockatoo is standing stylised on a wooden perch. The Cockatoo has a dark slate-grey coloured body with a scarlet red/orange coloured head with a wispy crest. This specimen stands with its wings positioned to its sides and has round glass bead eyes. The bill has a hooked shape and is horn-coloured. The legs and feet of this specimen are dark grey.taxidermy mount, taxidermy, animalia, burke museum, beechworth, australian museum, skin, reynell eveleigh johns, bird, australian birds, cockatoo, gang-gang cockatoo, cockie

This is a small wooden Honour Board in the shape of a shield. It has a dark varnish. At the top is a painted banner in red with the latin "SUA TELA TONANTI" . On the left and right sides of the banner are the corps colour patches. A grey background, black square with a red ball in the centre. 1 is shown as POW. 1 has a DSO. 1 has GBE, 3 have an Asterix beside their name. ww2, honour board, ordnance corps

1. & 2. Tunics - Khaki colour cotton drill fabric. Jacket shape with stand up collar, shoulder epaulettes, two front pockets with button down flaps, inside pocket. Button holes and matching holes for removable shank buttons. Two white cotton fabric manufacturers labels, front right side top and bottom. Bottom with handwritten information.Manufacturers labels - black ink print. Top - "M.TX" Bottom - DOCKET NO.6257/OCT 20 1942 / FACTORY NO 1030/ NAME/JACKET/TUNIC/COAT/" Purple Ink stamp "^/MM" Handwritten in blue ink "Peace Offr H.H. Derham/Khaki Drill"uniform, army, tunic