Yields information about the appearance of one Bendigo's single truck trams and its truck.Black and white photograph of Bendigo No. 14 side and truck or bogie - 21E truck. Photographed by John Webster, 2/6/1950. Copy 1 - On rear in ink "Bogey of Tram 14 Bendigo 14" and on right hand edge "BB9 F4 / T15 / F16 / 1/6/50 1/50 - 63 at 12, VV HP3".tramways, trams, bendigo, 21e trucks, tram 22

The drawing provides details of the two sets of springs that fit on either side of the axle box of a Brill 21E four-wheel truck. Gives load, sizes, and material dimensions. Revision E dated 7-11-1958. Prepared by the MTTB for use on four-wheel trams. Original drawing dated 30/9/1927Yields information about Brill 21E truck axle box springs.Drawing Foolscap size with two punched holes on the left hand side.tramcars, 21e trucks, brill 21e, springs, mmtb

Set of 14 colour photographs of the installation of the No. 2 end motor into No. 28's 21E truck on 20/2/2000 and its subsequent checking on Wendouree Parade. 1321.1 - Pushing truck with only No. 1 motor installed onto No. 5 road - Alan Snowball watching. 1321.2 - Motor on crane, with motor suspension bearings lying by rail. 1321.3 - Motor in position - still on crane 1321.4 - Bear caps being fitted - Warren Doubleday fitting cap 1321.5 - Lunch 1321.6 - Bearing caps in position, with split pins and cables joined and insulated with heat shrink 1321.7 - Gear end of motor frame showing previous welding repairs for cracked gear case support arm. 1321.8 - Dipstick tubes being fitted to oil boxes. 1321.9 - Packing motor suspension bearing boxes 1321.10 - St Aidans Drive - truck towed by 661 and service car 26. 1321.11 - ditto 1321.12 - ditto with out 26 - Alastair Reither and Simon Jenkins looking on. 1321.13 - truck with 661 at St Aidans Drive 1321.14 - placing truck under No. 28.21e trucks, motors, 28, btm, tram 26, tram 661

Set of 7 Agfa Colour slides, cardboard mounts, by Keith Caldwell dated 11.3.1962 of the transfer of cars from Footscray to the "Main System" the day after the system was closed. See Keith Kings history of Footscray notes. All trams running trolley wheels. .1 - Footscray depot cars X1 463, X2 678, X1 460 and X1 466 in Gordon St, about to turn into River Street. .2 - X2 678 turning from Nicholson St into Irving St. Footscray with the Rockmans Store in the background. This store was later demolished for the Ring Road. Also is J. Boltons Chemist shop advertising Kodak film and another shop advertising Darrell Lea Chocolates, Peters Icecream and ? Lopes fruit shop. .3 - X1 460 at same location. .4 - X2 678 crossing Maribyrnong River Bridge - note the person crouching down on the south side of the bridge behind the tram. .5 - X1 460 in Rosamond Road, just before the curve onto Williamson Rd. This site became the Bunnings site. The tram has a modified 21E truck. .6 - X2 468 as above with part of the curve in the view. Has an advertisement for Bon Stores of Hopkins St Footscray. .7 - X2 678 at ditto..1 - in ink - "Farewell Footscray" Sun 11.3.1962 - Footscray Depot cars departing areas en route to Main system." .2 - .7 all have "Footscray Sun 11.3.62"trams, tramways, footscray, closure, maribyrnong, gordon st, river st, irving st, maribyrnong river, bridges, x1 class, x2 class, rosamond rd, 21e trucks, tram 463, tram 678, tram 460, tram 466

Green folder gold block printed cover for "The J.G. Brill Company" and associated companies containing the following bulletins. All four pages, unless noted otherwise, printed on art paper, with the company name associated companies and agencies - e.g. Noyes Bros in Australasia. Contain a photo of the truck, a photo of a vehicle using the truck or bogie, line diagram, dimensions and parts diagram and listing. Bulletins 229, 246, 247 and 249 are for window (sash) components seats. Give diagrams and photos of this equipment. 1. No. 220 - The Brill 21E truck 2. No. 221 - Brill No. 50E truck 3. No. 224 - The Brill 27MCB truck 4. No. 225 - The Brill 76E truck 5. No. 227 - The Brill 39E truck 6. No. 228 - The Brill 77E truck 7. No. 229 - The Brill Renitent Post 8. No. 234 - The Brill 78M truck for light weight cars 9. No. 236 - Parts of Brill Short Base Pivotal Truck No. 27G 10. No. 237 - Parts of Brill Short Base Pivotal Truck No. 27F 11. No. 238 - Parts of Brill High Speed Truck No. 27E 12. No. 240 - Two Important Brill full elliptic Spring Trucks - 51E and 68E types. 13. No. 242 - The Brill 79E truck for Birney Safety Cars 14. No. 246 - Brill Reversible seats - Winner and Waylo types - 8 pages 15. No. 247 - Brill Non-reversible seats. 16. No. 249 - The Motorman's seats for Birney Safety cars. (different style of layout). All contained with a 'Shipman's "Common-Sense" Binder', comprising a green cloth covered cardboard, continuous cover, printed end papers, binder clips for inserting documents. Style No. 62848. Gold block front with name of company and Brill logo and on spine of document "Brill Publications" in gold. Has a ESCo date stamp of 3 May 1921 on front page of Bulletin No. 220.On front cover of first Bulletin, date stamp of ESCo, Ballarat "3 May 1921" in purple ink.trams, tramways, 21e trucks, j c brill co, bogies, interurban, birney, brill trucks

Demonstrates aspects of the two types of trucks or bogies used on Ballarat trams and their design basis. Photocopied from a catalogue.Five pages, each page trimmed to a slightly different width, photocopy of an article titled "Brill's 21-E traction truck", reproduced from the 1905 Brill catalogue. Gives details of the truck, its capability, basis, use in New York for example, how it functions, load and speed capacity, motor size, basic dimensions, limitations and drawings. 2nd copy held as well - on toner based copy rather than heat sensitive paper. Scanned copies of all sheets added 25/3/15.trams, tramways, trucks, 21e trucks, brill trucks

Catalogue No. 206 of the J. G. Brill Co. of Philadelphia PA, titled "Brill Trucks" on front cover and "City and Interurban Trucks" on page 1. Comprises: Card cover very light grey on outside, grey inside which is a larger size than that of the rest of the book. Has the names of the J. G. Brill associated companies (American Car Company of St. Louis, G. C. Kuhlman Car Co. of Cleveland Ohio, Wason Manufacturing Company of Springfield, Massachusetts and Compagnie J. G. Brill, Paris France) as well. On the inside of the front cover and on the inside back cover are patterns involving the Brill logo. To the printed catalogue is a matching out 4pp again with the same Brill logos. This sheet is the same size as the text pages. Forty page printed text on a heavy gloss manila colour art paper. Front cover gives details of Brill's office addresses, and agents, including the Australasian agent - Noyes Brothers. Page 3 gives an introduction to the quality of Brill trucks and page 39 gives an index to the various trucks and components. Each truck type has a photograph, parts list and dimension details. Trucks covered are: Radiax, 21E, 22, 22E, 27E, 27F, 27G, 27MCB, 39E, 50E. Equipment detailed are the Half-Ball brake hanger, oil retaining center bearing, standard journal (axle) box, solid forged side frames and axle data. Page 38 details the information to be provided when ordering trucks. Image of each sheet added 25/3/2015.On front cover, date stamp of ESCo, Ballarat "1 Apr 1914". The printers signature is shown on page 40.trams, tramways, 21e trucks, 22e trucks, j. c. brill co., bogies, interurban

Photo shows Q class tram No. 144 picking up a passenger at the Hawthorn Road stop in Dandenong Road. The tram has the destination of Brighton Cemetery with a sign under the driver's window, "via Windsor". The Conductor can be seen leaning out from the rear of the tram. A lady is possibly waiting for the next service. On the other side are 8 people at a tram stop waiting shelter. Many are dressed in summer clothing, with some looking at the photographer; most likely the photo is taken from the top of an overhead tower wagon. There is a sign stating "This road for tram traffic only". In the left-hand foreground is a light fitting with a coloured lens showing the it is a tram stop. There are two horse-drawn carts on the south side of the roadway.Yields information about tram services in Dandenong Road and the road itself at the intersection with Hawthorn Road early to mid 1920s.Black and white photo with notes on the rear.In ink on the rear "Q class 139-150, combination straight sill, 7'6" wheelbase, 21E truck GE203 motors, 13.027 tare"trams, tramways, dandenong road, hawthorn road, shelters, tram 144, q class, brighton cemetery

Photo shows Q class tram 145 in Dandenong Road, at a stop picking up a male passenger. The tram has the destination of Brighton Cemetery with an Auxiliary board "Via Dandenong Road." The conductor can be seen at the back of the tram observing the passenger boarding. Photo possibly mid 1920s.Yields information about tram services in Dandenong Road during the 1920s and the road itself.Black and white photo with notes on the rear.In ink "new cars Q class 139 - 150, combination straight sill, 7'6 wheelbase, 21E trucks GE203 motrs, 13.027 Tons Tare."trams, tramways, q class, dandenong road, tram 145, brighton cemetery

Series of four photographs by Lloyd Rogers of Victorian Railways tramcar No. 20 1 - arriving at Preston Workshops - 2/12/1992 2 - The body of VR Tram 20 on stands at Preston Workshops - 1993 3 - the 21E truck from the tram at the Preston Workshops with Lloyd Rogers standing alongside 1993 4 - The 21E truck from VR 20 is being reassembled at Bendigo tram depot 1-2-2005.Yields information about former VR tramcar No. 20 after its recovery.Series of four photograph printed on Kodak paper.Two have details on rear including photo numbervr trams, tram 20, tramcars, preston workshops, bendigo

Black and White photograph of a Brill 21E type, used on four wheel trams. Note the motor suspension spring is not located in the original position provided for on the truck. One of a series of photographs done by the MMTB to illustrate the various types of bogies used by the MMTB. Possibly during the 1960's.trams, tramways, mmtb, brill trucks, brill 21e, bogies, trucks, preston workshops

Black and White photograph of a Brill 21E type, used on four wheel trams. Note the motor suspension spring is not located in the original position provided for on the truck. One of a series of photographs done by the MMTB to illustrate the various types of bogies used by the MMTB. Possibly during the 1960's. Two copies held.trams, tramways, mmtb, brill trucks, brill 21e, bogies, trucks, preston workshops

Set of five digital images of the Brill 21E truck for ESCo No. 12. First two at Harrybuilt Engineering 20-11-2024 and the two of the delivery to Ballarat are on 11/12/2024. All photos by Paul Mong. Yields information about the construction of the Brill 21E truck by Harrybuilt.Digital image of 5 colour photographs.tramcars, btm, brill 21e, tram 12, harrybuilt

Drawing titled "No 2 end brake lever" showing a part of a Brill 21E truck, shows the positioning of the holes for other parts of the brake rigging. Would have been used at the depot or the SECV Workshop for the drilling of a plate. Item undated.Yields information about the position of the drill holes on a brake lever fitted to single truck trams.Hand drawn drawing in pencil on plain quarto sheet.tramcars, equipment, rolling stock, brakes, brill 21e

Photo shows an ESCo tram at the corner of Doveton and Sturt St, possibly No. 18. The Town Hall is in the distance. The tram has forward lean or sag indicating collapsed springs on the No. 21E truck. Has adverts for Suttons Music store and Bushells teas.Yields information about ESCo trams during the 1920s and their operating condition.Light card photograph held on sheet 8416 by four photo corners.trams, tramways, sturt st, doveton st, esco, 21e truck

Article looks at the development of the maximum traction bogie, the Brill 22E in regard to the engineering aspects. Written by N. F Henley with drawings of the various concepts and history of the Brill truck. See item 9663 for s similar article on the Brill 21E truck.Yields information about the development of the Brill 22E truck which is used on some of the BTM trams.Seven A4 sheets, photocopy of an article titled "The development of the Manchester bogie" from the UK magazine Tramway Review published by the Light Railway Transit Association, Winter 1988.trams, tramways, maximum traction, bogies, trucks, brill trucks

Yields information about the size of a Ballast trailer that was built but was never used.Digital image from the Wal Jack Ballarat Album of a drawing of a wartime built ballast trailer - never used, scrapped about 1943. Shown as being built on a 6'6" 21E truck frame. No details as to who made the photograph or when/ See image i2 for rear of photograph.No details on rear.trams, tramways, ballast trailer, work trams

Tramcar record for SEC Ballarat No. 16, builder, system location, short history and work in Ballarat. Loose on the same folder was a typed sheet of paper dated 21-6-55, noting the SEC proposal for this tram, not intended to recondition it. See btm5526i1.jpg See Reg Item 5614 for a photo of the 21E truck after the body was sold and disposed of.Yields information about the history of individual tramcars in Ballarat.Handwritten note on foolscap lined sheet outlining the history of Ballarat Tramcar No. 16, who built for, date to Ballarat, painting and other changes to the tramcar as compiled by Wal Jack. Part of a series on each SEC Ballarat operated tramcar, except for the ESCo trams. Contained within Reg Item 5507 - Foolscap binder with green covers, black binding edge and metal clips. trams, tramways, ballarat, tramcars, tramcars of ballarat, tram 16

Newspaper clipping and photograph about the departure of the first tram from Ballarat before closure on 2/9/1971. Details the loading, the separation of the 21E truck and transport to Hamilton. Notes that the remaining 18 will be transported to other locations while 6 will remain in Ballarat. See item 3768 for a print of the photograph. The tram returned to the BTPS in 1977. See reference.Yields information about the tramcars following the cessation of tram services in Ballarat - trams being sent to new homes and how this was done.Newspaper clipping from The Courier, 3/9/1971tramways, secv, tramcars, tram 33, transport, closure, hamilton, depot

Photo shows J class tram No. 82 picking up a passenger at an unmarked stop in Dandenong Road before the Wattletree road junction. The tram has the destination of Wattletree Rd with a sign under the driver's window, "via Windsor". The photo is taken from the top of an overhead tower wagon. The tram later was sold to Ballarat where it ran as No. 16.Yields information about tram services in Dandenong Road.Black and white photo with notes on the rear.In ink on the rear "J No. 65 - 83, Combination straight sill, 36 seating capacity, 21E trucks, 6'6" wheelbase 12.007 tons tare" and in pencil 'C J Fraser, 154 Little Collins St, near Russell St, phone 4358"trams, tramways, dandenong road, j class, tram 82, wattletree road

Black and White photograph of a MMTB workshop dolly made from a former Brill 21E truck cut down and fitted with centre pin and bolsters. One of a series of photographs done by the MMTB to illustrate the various types of bogies / trucks used by the MMTB. Possibly during the 1960's. Two copies held.trams, tramways, mmtb, bogies, trucks, preston workshops, brill 21e

Black and white negative, by Wal Jack, of Freight car No. 17 in Cameron St, Brunswick. Has the Coburg rail line in the background. Shows the 21E truck. Dated 8/1940. May not be a Wal Jack photograph as odd negative size. See also Reg item 5333 for another photo of this car at Brunswick.trams, tramways, freight tram, brunswick, cameron st, brill 21e, tram 17

Black and White photograph of a MMTB modified 21E for use under X1 class. One of a series of photographs done by the MMTB to illustrate the various types of bogies / trucks used by the MMTB. Possibly during the 1960's. See also Reg item 4463 for another variation of the use of former 21E trucks. Two copies held.trams, tramways, mmtb, bogies, trucks, preston workshops, x1 class

Letter typed on MMTB Letterhead quarto paper with the name of the Secretary, Telegraphic address and contact details - to J. Bounds of East St Kilda regarding this letter requesting advice on the Brill 21E truck at the Hawthorn Driving School. Advised that it had agreed to dispose it to the TMSV. Dated 6/11/1972. Signed R. M Brown (?) Assistant Secretarytrams, tramways, mmtb, brill trucks, hawthorn, tmsv

Black and White photograph of a MMTB modified 21E for use under X1 class. Has chalk marks "460-1-BR". See also Reg item 4464 for another variation of the use of former 21E trucks. One of a series of photographs done by the MMTB to illustrate the various types of bogies / trucks used by the MMTB. Possibly during the 1960's. Two copies held.trams, tramways, mmtb, bogies, trucks, preston workshops, x1 class

Yields information about disposal of tramcars from Ballarat and 21E trucks.Newspaper clipping from The Courier, 30/1/1956, titled "The End of a Tram" with a photo and caption of depot workers pushing a 21E truck back into the depot after the body of a single trucker was sold for a "sleepout" - See Reg Item 5526 - most likely No. 16 as the dates match up. Contained originally within Reg Item 5507 at the back of the binder. For items see btm5507 loose items list.pdf disposal, 16, sale of trams, depot

Instruction - 3 sheets of a former 8 or 12 page document titled "Westinghouse Magnetic Brake" describing the mechanism for magnetic and clamp brakes on 21E trucks, bogies, 22E, trailers. Lists the advantages of the Westinghouse Magnetic Brake. Has a note on the last pages that 2000 Westinghouse Magnetic Brakes have been sold in Great Britain along up to Nov. 1904. Presumed published in the UK by The British Westinghouse Electric & Manufacturing Co. Ltd. London and Manchester.trams, tramways, westinghouse, instructions, maintenance, brakes

Set of drawings and photocopies of sanding equipment on Ballarat Tramcars, provided to the Launceston tramway Museum for information.Copy of Correspondence with the Launceston Tramway Museum 31/12/2006 concerning sand ejector equipment fitted to Ballarat tramcars. Comprises: Covering letter dated 31/12/2009 Photographs of the Ejector unit with fittings - two views Photograph of the inlet pipe Sketch of the air inlet pipe - prepared by Warren Doubleday Prints of drawings - BA - T7 - 7654 - Ejector for Sand Box, Fabricated type - 21E truck, SEC 1938 - made from scans ex Microfilm BA - T7 - 7647 - Ejector for Sand Box, Brill 21 E Truck - SEC 1938 - cast type.tram, trams, tramcar equipment, sanding equipment, sand ejectors, letters

Series of four Black and white photographs of tram 26 on No. 2 road at the BTPS Depot, undergoing replacement of the broken frame on the Brill 21E truck. The tramcar record sheets note that the car was lifted 15-3-1975 and lower 27-7-1975 and tested on the same day. Seems to have re-entered service on 28/9/1975. .1 - on the front of the road, with a "Defective Not for Service" sign. .2 - car on jacks being either lifted or lowered. .3 - tramcar body lifted showing the word to replace the side frame underway, has the good and broken side frame in the view. .4 - tram being either lifted or lowered - with Rolf Jinks in the view. trams, tramways, btps, depot, brill trucks, maintenance, tram 26

Yields information about the drawings that were used by the depot or workshop staff as reference drawings. Has a strong association with the depot workshop staff. Yields information about equipment on Ballarat tramcars and Signalling.Folder containing 46 blueprints or Dyeline prints of SEC tram equipment drawings. Front of folder made from a cloth back sheet of paper extended to secure to a thick cardboard runner. Rear of folder made from an old tram advertising panel or cardboard sheet, cut to size and secured to a thick cardboard runner with a cloth backing on both sides. Sheets secured with three brass screwed clips. Front cover damaged in bottom right hand corner. Rear cover breaking apart on outside around cloth binding. Heavy dirt marks from “grease” on bottom half of rear cover. Contains 46 drawings which have been individually catalogued and numbered on the rear of each drawing within the folder. Some of the drawings have been folded. Reg Item Micro Film No. Old BTPS No. SEC Drawing No Title 4807 42/4 1 VB4/8103C Westinghouse T1F Controller Main Cylinder Segments. 4867 47/2 2 BA-T8-8128 Westinghouse 225N Motor Case Bolt 4830 22/3 B 3 BA-T7-7666 Half Ball Brake Hanger Link, Driving Wheel, Brill Maximum Traction Truck 22E 4868 44/3A 4 BA-T8-8113 Split Suspension Bearing for Type W225 Motor (Westinghouse) 4869 52/2 5 BA-T8-8158 Contact Tips for G.E. Compressor Controller 4818 52/3 6 BA-T8-8159 GE B-23 Contact Finger Tips for G.E. Type ‘B’ Main Cylinder 4870 6/1 7A BA-T3-6734 Brass Nut for Switch Mechanism 4829 6/2 7B BA-T3-6735 Tongue Clip Link for Switch Mechanism 4871 6/3 7C BA-T3-6736 Fulcrum for Switch Mechanism 4872 6/4 7D BA-T3-6737 Plunger for Switch Mechanism 4832 7/6 8 BA-T3-6754 Pivot for Switch Mechanism No numbers 9 or 10 4873 17/5 11 BA-T7-7639 Detail of Motor Pinion for Brill Cars 4831.2 21/4 B 12 BA-T7-7661A Half Ball Hanger Links – single bogie trucks 4874 21/6 13A BA-T7-7663 Axle Box Inner Spring Driving Wheels Maximum Traction Truck 22E 4875 22/1 13B BA-T7-7664 Axle Box Outer Spring Driving Wheels Maximum Traction Truck 22E 4876 22/2 14 BA-T7-7665 Body Spring Brill Maximum Traction Truck 22E 4830.2 22/3B 15 BA-T7-7666A Half Ball Brake Hanger Link Driving Wheel Brill Maximum Traction Truck 22E 4877 22/4 16 BA-T7-7667 Body Spring, Brush Maximum Traction Truck 22E 4820.2 22/6 A 17 BA-T7-7669 Wear cups for Half Ball Brake Hanger Links, Single & Double Bogie Trucks 4878 50/5 18 BA-T8-8149 Connections of Line Breaker and Ratchet Switch for use with Drum Controller 4879 74/6 19 BA-T13-8757/9 Signal boxes, Back of Panel Wiring and External Connections 4880 45/1 20 BA-T8-8116 Trolley Harp 4806 15/3 21 BA-T7-7625 Equalizing Lever, Fulcrum, Brill 21 E truck 4881 15/5 22 BA-T7-7626A Brake Beam Fulcrum Brill 21E truck 4808 16/1 23 BA-T7-7628 Pinion Remover, GE 201G and GE 202 motors 4882 16/3 24 BA-T7-7630 Spring Posts, Brill 21E Truck 4883 21/3 25 BA-T7-7660 Brake Shoe Holder, Driving Wheel, Maximum Traction Truck Brill 22E 4884 21/5 26 BA-T7-7662 Brake Rod Guide, Single Bogie Trucks 4885 22/5 27 BA-T7-7668 Brake Shoe Holder, Pony Wheel, Maximum Traction Truck Brill 22E 4809 42/2 B 28 BA-T8-8101 Trolley Wheel and Axle 4815 42/1 B 29 BA-T8-8102A Motor Suspension Bearing, GE 202 Motor 4796.2 42/5 30 BA-T8-8104 Connection Diagram WH 225N Motor 4886 42/6 B 31 BA-T8-8105B Motor Suspension Bearing, GE 201 Motor 4797.2 48/6 32 BA-T8-8137 WH T1F Controllers 4816 49/2 33 BA-T8-8138 Connection Diagram GE 202 Motor 4887 49/3 34 BA-T8-8139 Connection Diagram K-36-J Controller 4888 50/3 35 BA-T8-8146 GE K-36-JR Controllers, with line breaker (Connection diagram) 4889 50/6 36 BA-T8-8150 Commutator for Westinghouse 225N Motor 4846 51/1 37 BA-T8-8151A Armature Bearing Lining, Commutator End, Type GE 201G Motor 4813 51/2 38 BA-T8-8152 Armature Winding Diagram Westinghouse 225 Motor 4840.2 51/40 39 BA-T8-8154A Armature Bearing Lining, Pinion End, Type GE201G Motor 4890 51/6 40 BA-T8-8156 Armature Bearing Lining, Pinion End, Type GE202A Motor 4891 52/1 41 BA-T8-8157A Armature Bearing Lining, Commutator End, Type GE202A Motor 4892 64/5 42A BA-T9-8392A Step Hangers, Single and Double Bogie Trucks, Hinged Type 4785.2 64/6B 42B BA-T9-8392/1A Step Hangers, Single and Maximum Traction Trucks, Fixed Type 4812.2 43/1 43 BA-T8-8106B GE K36J Controller, Main Cylinder Segments 4893 50/2 44 BA-T8-8145A GE B23E Controller, Main Cylinder Segments 4816 65/2 45 BA-T9-8394B Door Lock for Motorman’ Cabin Maximum Traction Trucks. 4810 73/3 46 BA-T13-8757 Ballarat Electric Tramways Signalling System, Arrangements & Details of Box.On front cover of folder, "1 - 46"trams, tramways, drawings, ballarat, sec, depot, workshops