Used to support bucket on a windlass rope.mining, equipment, trades, blacksmithing

Mining Safety Hook. Used to lift Ore up from shaft.stawell

Mining Safety Hook. Used to lift Ore up from shaft.stawell

Invoice with William letterhead. william heath, blacksmith, invoice, letterhead, safety cage, safety hook

Handwritten extract from the Bendigo Advertiser 5/12/1893 where three miners had a narrow escape in a winding accident at the Huster's Reserve No 2 Company's Mine, in Pall Mall. At the change of shift, three miners, William Merrin, Frederick Willoughby and E. Johns got into the cage on the western compartment to be lowered to the 845 ft. plat. The Driver Russel lost control of the engine and hauled the empty cage in the eastern compartment to the poppet heads. Cage went up with a crash, but the safety hooks caught it and let the rope go. The men in the cage in western compartment were very alarmed has cage hit the bearers on the 845 feet plat with considerable force. If it had crashed through the bearers they would have landed in the water below. The shaft was 1070 feet deep. The Mine Manager, S. T. Glanville ordered the driver off the mine; another rope re-attached and the men hauled to the surface.document, gold, mining accidents, sensational winding accident at the hustler's reserve no 2 co, william merrin, frederick willoughby, e johns, driver russell, s t glanville

From the Argus, Friday 18 July 1879:- SAFETY MINING CAGES. The report of the board on safety mining cages was laid on the table of the Legislative Assembly fortnight The board, which has tested the following inventions Nances, Williams patent, Jackson and Middleton's patent Sesmours patent, Allans patent, and Hassan a patent, reports as follows - 1. That the preponderance of evidence given by miners and others qualified to form an opinion is strongly in favour of the adop-tion of a safety cage for general use in the mines of this colony, provided that a reliable invention can be brought forward, and its practical utility satisfactorily determined 2. That in view of the rapid increase of cage accidents, and supported by the evidence before them, the board are of opinion that some special provision should be made to check such a prolific source of danger as is shown to exist in the working of the shaft and machinery employed for winding purposes. 3. That this check could be imposed by means of such a regulation as that at present contained in the statute, i e -" Every cage used in a mine shall be fitted with special and suitable appliances to prevent its sudden fall down a shaft and also to prevent its coming into contact with the poppet heads." The board, however, consider that mine proprietors should be permitted to exercise their own discretion in the selection of safety cages, but safety hooks and balance catches must be used in connexion with every case 4. That the board have witnessed trials of all the inventions brought under their notice, and from the result of their observations the members are of opinion that the adoption of these safety appliances will afford additional security to the large section of the community engaged in mining operations.48 foolscap pages report stitched together. safety cages, safety mining cages, george collins levey, mining, mitchell and osborne's patent safety catches for mining cages, mining cages, seymour's patent safety cage, pryor's safety cage, white's safety cage, mining accidents, dyke's freehold gmc creswick, angelo mining co castlemaine, britannia qmc ballarat, alexander kennedy smith, george r. fincham, henry roberts williams, robert clark, r. richardson, allan's patent balalrat, hassan's patent daylesford, david white, charles stewart, w.h. grainger, h.b. nicholas, t. hassan, r. allan, a.k. smith, james thomson, william collard smith, j.h. seymour, john s. delbridge, william buttle, james davidson, j.p. carolin, r. clark, thomas eyre, george marshall, g. thureau, william bottoms, robert carr, j.c. march, john keam, david park, j.a. lewis, lester's hotel, ballarat, robert allan, nancarrow saftey cage, robert malachi serjeant, robert henderson, g.f. smith, r.w. newman, william benson, f. bennett, john sharp, thomas couchman, john a. wallace, john small, william h. grainger, james cowling, tools

This item was worn by Marjorie Burton during summer holidays in Croyde,a village on the west-facing coastline of North Devon, England. In England she did office work – typing, shorthand and secretarial work - in accountants’ offices and also trained as a comptometrist with Burroughs in London. She came from middle-class working church-going family. Her mother was a milliner who made many of Marjorie’s clothes, hats and outfits. Marjorie married in 1938 to a salesman who later became a mechanic in the R.A.F. during WW11. Marjorie Burton ( nee Whiteman), born 12 June, in Birmingham, England came to Orbost in 1995. This item is an example of a handcrafted item and reflects the handcraft skills of women during the mid 20th century.A pale hand-stitched torquoise coloured cotton bikini set. The bottoms are briefs and elasticated at the front. They have high rise leg openings . The top is a bra style with a strap pinned at the centre of the back with a gold safety pin and stitched at the shoulders to loop over. There are 2 hooks and eyes for closure.women's-clothing swimwear burton-marjorie

This item was made by Mrs Whiteman and worn by her daughter Marjorie Burton. Marjorie Burton ( nee Whiteman), born 12 June, in Birmingham, England came to Orbost in 1995. In England she did office work – typing, shorthand and secretarial work - in accountants’ offices and also trained as a comptometrist with Burroughs in London. She came from a middle-class, working, church-going family. Her mother was a milliner who made manyof Marjorie’s clothes, hats and outfits. Marjorie was married in 1938 to a salesman who later became a mechanic in the R.A.F. during WW11. This item is an example of a home-made item of clothing and reflects the needlework skills of women in the first half of the twentieth century.A short white linen petticoat opening at the back with 2 metal hooks and eyes. The waist has threaded elastic. Sewn to the top are two long tapes fastened with safety pins - probably for hanging. The bottom panel is double with a scalloped hem.petticoat women's-clothing underwear burton-marjorie

A razor strop is flexible strip of leather or canvas used to maintain a shaving edge on a thin blade such as a straight razor. Fine powdered jeweler's rouge or other pastes can be added as an abrasive to polish the blade. The strop may be a hanging strip or a hand-held paddle. This one is a hanging strop. Strops were quite commonly found in barber shops and homes before the invention of the safety razor, They are still used for sharpening tool blades.This item is an example of the self-reliance shown by rural families when household necessities were not readily available.A flexible double-layered horse hide leather strop. One strip has a slightly coarser texture. This is a hanging strop which has a metal swivel on top so that the strop can be turned over while hanging from a hook/peg.On hand grip The Keen Edge Strop, genuine horse hide All Black Stropper No. 2strop razor-strop shaving personal-effects

A rim splitter was used on the outer rims of older vehicles to facilitate removal and replacement of tires. The tool was used to remove a tyre and replace it onto a split wheel rim. After the air was let out, the safety rim key was pulled. The swing arms were spread out and the three arms evenly spaced around the rim. The single arm with the screw gear needed to be close to the split so that the hooks fit on the rim and the rim was then pulled inward and the tyre could be be removed from the rim. After the tire was repaired or a new one was ready to be put on the collapsed rim the tool was used to push the rim back together and the safety key could be reinserted. A rim splitter were a universal type tool used for many cars of the 1920's and 1930's.A cast iron rim splitter which has two hinged side arms with hooked ends. The middle shaft has a hooked end and an inner bolt that can be screwed up or down.St Joseph Michigan Hercules Product Co Made in U.S.A. L 7motoring rim-splitter tyres tool

This shaving strop is typical of those used in barbers shops. It was used to sharpen the edge of a straight blade razor.This item is of social and historical interest and belonged mainly to the era prior to the invention of safety blades and electric razors.Light brown double leather strop with black leather handle at one end and metal hook at the other end. There is text on both ends of the strap and the handle.On handle Super 99."Sharpen" on strap section with carborundum at the other end. On the reverse: genuine horse hide Finish . shaving strop, barber's strop, warrnambool

Part of the Leo Reoch Cohn Collection. See Catalogue No. 5527.2 for his service record. The badge represents the 1st Australian Armoured Car Section.A triangular metal and enamel unit badge depicting the colour patch of the Armoured Car Section suspended below a gold coloured disc. The disc and badge are connected with a gold coloured chain with a safety pin attached. The back of the disc has a pin and hook attached to allow the wearer to fasten it to a garment. The disc features Arabic writing. The triangular badge has a central enamel purple triangle which is bordered with white enamel.Stamped on the back of the triangular badge: 'E. B. EDWARDS, (hallmarks below)'.souvenir, armoured car section, leo reoch cohn, unit badge

This grappling hook is constructed from two U-shaped lengths of steel pipe, each pinched together in the centre of its arm then the ends spread apart and formed into points. The two pieces are joined with a length of heavy chain, with the end links closed to make the chain into a circle. the hook is usually attached to a rope, chain or pole of suitable length for the job undertaken. Another name for a grappling hook is a grapnel hook. Grappling hooks come in many shapes and sizes and have numerous uses. Some are carried on board vessels and used for pulling things on board or out of the sea, rescuing people from the sea, pulling other vessels closer and moving cargo. They may be used for dredging the seabed for submerged objects. A grapnel anchor can be used to moor or stabilise a vessel. The hook can be thrown out to catch on something, such as a clifftop, and then used for climbing. A form of a grappling hook, a grapnel, can be used for military purposes and is fired from a purpose-built gun or launcher. This grappling hook is an example of equipment used onboard a vessel for safety and functional purposes. Grappling hooks have been used through the centuries and their design has remained basically the same. Grappling hook with four pointed arms. The hook comprises two double-pronged grappling hooks on a chain joined to form a circle. Hooks are made from strong steel.flagstaff hill, maritime village, maritime museum, great ocean road, shipwreck coast, grappling hook, grapple, grapple anchor, marine tool, marine equipment

The Manifolds were a significant pioneering pastoral family in Western Victoria. The donated riding skirt originally belonged to Mrs Edward Manifold, formally Beatrice Mary Synnot Anderson. Beatrice was Edward Manifold’s cousin once removed whom he married in 1900. Edward, the son of John Manifold, was born on 15 November 1868 and educated at Geelong and Melbourne Grammar schools and at Trinity Hall, Cambridge (B.A., 1891). He chose the Danedite portion of land at Purrumbete, and on the death of his bachelor brother Thomas Peter (1863-1895), after a hunting accident, he took over his allocation, Wiridgil. He also owned Boortkoi, near Hexham and on these properties, he ran merino sheep, a Lincoln stud which dated back to 1870, and Shorthorn cattle. 3000 acres were also leased to dairy farmers. Edward was a member of Hampden Shire Council in 1909-31 and three times president at Camperdown. The town was largely bordered by Manifold land and partly dependent upon the local pastoral dynasties, which benefited the local area from the families’ various business interests. Though an offer to build public baths to commemorate the Queen Victoria Jubilee in 1897 was not proceeded with, the town acquired a hospital, a reserve on Mount Leura, a clock tower and a cricket pavilion, as well as notable donations from the Manifolds to St Paul's Church and the grammar school. Edward was a keen polo player and racing man. He was also a successful owner of steeplechasers and a committeeman of the Victoria Racing Club for many years. He was also a member of many Western District racing clubs. On the 16 July 1900, Edward had married his sixteen-year-old cousin Beatrice Mary Synnot Anderson by whom he had three sons Thomas Peter, Andrew and Robert Edward Manifold. Edwards's estate at his death was valued for probate at nearly £500,000. Edward died following an operation on 14 February 1931 at a private hospital in Yarra Vale Melbourne. Beatrice passed away in 1954, aged 79 in Ballarat where she was born in 1874. Contextual historic Family background: The Manifold brothers Thomas (1809-1875), John (1811-1877) and Peter (1817-1885) were the fourth, fifth and sixth sons of William Manifold and Mary, nee Barnes, of Courthouse Farm, Bromborough, Cheshire, England. The family had decided to emigrate to Van Diemen's Land. Thomas was sent ahead, arriving in Hobart Town on 23rd January 1828 with £1500 and a letter of recommendation from the Colonial Office. Thomas acquired 1280 acres on the west bank of the Tamar River. John and Peter, with their parents and three sisters, arrived on 8th July 1831. Land grants by then had finished but William brought ninety acres next to his son Thomas’ land and on the combined properties the family built Kelso House. The Manifolds’ properties were comparatively poor and when news of the Port Phillip District, in Victoria reached Thomas, he lost no time in coming to see for himself in February 1836. He was impressed with what he saw and hurried back to Tasmania to buy lambs and ewes. With one of his brothers, on July 9th he landed his stores at Point Henry and proceeded to occupy both sides of the Moorabool River. Thomas, at the end of the year, returned to Tasmania and left Peter and John to run the new property. Thomas, however, returned to Victoria for several visits and on one of these visits he, along with his brothers, examined the country near Ballarat. In December 1838 they managed to penetrate the Stony Rises, and Peter and John reached Lake Purrumbete and the Mount Leura country. During this time, on 4th July 1838, Thomas married Jane Elizabeth, eldest daughter of Captain Walter Synnot, formerly of Ballinate, County Armagh, Ireland, and then of Van Diemen's Land. Thomas joined his brothers, and they occupied the Purrumbete run in January 1839. On the journey to Purrumbete they could not take their stock and drays through the Stony Rises, so went north of Lake Corangamite, to the neck of land between it and Lake Gnarpurt. By April the move from Moorabool area was complete. As yet they had no hut and were working day and night, but their delight in their new run was unbounded. John wrote to his mother: “We are at last got to the land we wished for it is a beautiful place, and cannot be surpassed by any I have ever seen”. The three brothers occupied Purrumbete together, breeding both sheep and cattle until Thomas went to Grassmere run on the Merri River near Warrnambool in 1844. John and Peter soon gave up breeding sheep but retained the well-known '3M' brand for the cattle. These were Shorthorns, derived from four bulls originally imported by the Boldon brothers and later improved by further importations, and were renowned for size and quality. By the time of the gold rush in 1851, John and Peter were breeding over 1000 head a year, as well as fattening stores. The diggings at this time had disorganised Grassmere by drawing away Thomas's men, and his wife decided to take her two sons and two daughters to Europe for their education. Thomas gave up the property next year, went to England to join his family, and eventually brought the family back to live in Melbourne. At Purrumbete things were different. The brothers, John and Peter, preferred black stockmen to white, so the discovery of gold upset them very little while providing the very market they required. John was on his second visit to England when the rush started, and Peter went in his turn soon after John returned. On 2 September 1856 John married Marion Thomson, at Cormiston, Van Diemen's Land. They had four daughters and five sons, from three of whom, William Thomson, James Chester and Edward, the later generations of the family descend. Through the years the brothers had to contend with the scab, fluke and footrot, depression, rabbits, bush fires and pleuro-pneumonia. In 1861 they appointed as manager Henry Manifold Matson, their nephew, who had already been with them for five years. Thomas died in Melbourne on 7 November 1875, John at Purrumbete on 3 January 1877 and Peter at Purrumbete on 31 July 1885. Devout members of the Church of England, John and Peter, during their lives, gave generously towards building St Paul's Church, Camperdown, and guaranteed part of the vicar's stipend. Peter was a member of the Hampden and Heytesbury Roads Board from 1859 and carried on into the Hampden Shire Council when it was formed in 1864. However, it was not for public works that they were known, but for their personal example. In a new land where speculators and adventurers were all too common, the Manifold brothers were among those who intended it to be their home and their children's home. Industrious, unpretentious and hospitable, they were respected in their community as men of the highest integrity. This riding habit is a characteristic example of the type and style of riding clothes that well-dressed ladies wore in the 1920s. It highlights the changes that were beginning in society for women. Prior to 1918 ladies still had to ride side-saddle with skirts over Jodhpurs. Society of the time regarded women riding astride as unseemly and just not done. This riding habit is particularly significant on a number of levels, it shows the beginnings of change in society's attitudes through women's fashion after the First World War. A change that was to bring a start to a more liberating societal attitude towards women after the successful establishment of the Representation of People Act 1918 that gave women the right to vote. This garments provenance is linked to one of Victoria's important pioneering families the Manifolds, one of the first families that came from Van Diemen's land to settle the Western District of Victoria in 1844. Originally the garment belonged to the wife of the great-grandson of pioneer William Manifold, Edward Manifold who married Beatrice May Synnot Anderson, Edwards Cousin in 1900. The garment was made by the Mayfair tailors J. Busvine & Co. in the early to mid-1920s (estimate) who at the turn of the century were tailors to the Courts of Europe. Their clothing is highly collectible today and examples can be found in a number of significant museum collections around the world, notably the Metropolitan Museum of Art in New York and the FIDM in Los Angeles. Safety skirt/apron, part of a three-piece, side saddle riding habit tailored for Mrs Edward Manifold. This side saddle skirt is made from black woolen material fixing at the waist with two metal hooks and three buttons to the front opening. One internal concealed pocket lining to the top part of the apron made of cotton the seat is shaped for side saddle riding and the skirt wraps around the body the longer side draped over the leg that is in the stirrup. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, side saddle riding habit, side saddle safety skirt, side saddle apron, mrs edward manifold, beatrice manifold, female riding habit 1920s, shipwreck coast, flagstaff hill maritime village, great ocean road

A razor strop is flexible strip of leather or canvas used to maintain a shaving edge on a thin blade such as a straight razor. Fine powdered jeweler's rouge or other pastes can be added as an abrasive to polish the blade. The strop may be a hanging strip or a hand-held paddle. This one is a hanging strop. Strops were quite commonly found in barber shops and homes before the invention of the safety razor, They are still used for sharpening tool blades. This one was owned and used by Mr Bill Weston, an early Orbost sleeper cutter.This item is an example of the self-reliance shown by rural families when household necessities were not readily available.A brown leather (probably horse hide) razor strop with a double hook at one end. It consists of two strips of leather with padded 'tongue' at bottom. This is a hanging strop which has a metal swivel on top so that the strop can be turned over while hanging from a hook/peg Front top in gold : MALWA Base in gold: 910razor-strop shaving personal-effects

A razor strop such as this one was used to sharpen and polish straight-edged razors. This particular design has a swivel hook with a locking clip that allows for movement as the strop is being used. This strop is branded "Sherlite". On May 5th, 1922 the Commonwealth officially accepted and advertised the Trade Mark Application of Thomas Sherry of Victoria, for the Trade Mark of "Sherlite" to be used under the heading of "Leather, Skins unwrought and Wrought”. Thomas Sherry’s application was to use the word “Sherlite” for detachable soles made of rubberised leather. Straight razors and cut-throat razors were the major tools for shaving before the safety razor was invented in the 1880s and even today specialist shaving shops still sell straight razors. Along with the razor, the process of shaving would commonly involve lathering up shaving soap with a shaving brush that had boar bristles. Men could own several razors and rotate them through the week and some shops sold the razors in a set, a razor for each day of the week. Straight razors could require stropping more than once during the shaving of a heavy beard, and stropping would also be performed at the end of each shave. Honing would only be performed two or three times a year, preserving the blade's edge. A lot of skill was needed to hone and strop the blades of these early razors and the methods to do so were a large part of the curriculum in Barber colleges. The razor would be sharpened on a grinding wheel then honed on sharpening stone and finally finished using a strop. Straight edge razors would usually be sold unfinished and that process would be completed by the customer. A razor strop, usually made from leather, thick canvas, or light timber, would be used to straighten and polish the straight razor for shaving. Strops could also be used to polish other blades such as knives, small metal tools, and chisels. Sometimes an abrasive polishing compound is also used to give a mirror finish. Some strops, such as this one in our Collection, are designed to be used while hanging from a nail or peg, while others are handheld. The person using the strop would draw the spine of the blade down along the strop with the blade following, without putting any pressure on the blade. At the end of the stroke, rotate the blade over its spine then draw the spine along the strop again so that the edge moves away from the top. The finer grade of leather strap is used to give the final finish.Razor strop, leather, and metal. Sherlite brand, double straps: two straps of different grade leather joined at ends with metal fittings. Stropping faces; sharpening surface is stained red and finishing surface is stained black. One end has a padded, bulbous-shaped leather grip handle, the other end has a metal, swivel hook hanger. Inscriptions painted in gold on leather at the hook end.Razor strop, leather and metal. Sherlite brand, double straps: two straps of different grade leather joined at ends with metal fittings. Stropping faces; sharpening surface is stained red and finishing surface is stained black. One end has padded, bulbous shaped leather grip handle, the other end has metal, swivel hook hanger. Inscriptions printed in gold on leather at hook end.Printed gold lettering stamped “Sherlite”flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shaving leather, shaving accessory, barber’s equipment, barber shop razor strop, razor strop, straight razor, razor and knife sharpener, sherlite razor strop, personal effects, toiletries, thomas sherry

The first spring balance in Britain was made around 1770 by Richard Salter of Bilston, near Wolverhampton. He and his nephews John & George, founded the firm of George Salter & Co., still notable makers of scales and balances, who in 1838 patented the spring balance. They also applied the same spring balance principle to steam locomotive safety valves, replacing the earlier deadweight valves. https://en.wikipedia.org/wiki/Spring_scale Today, spring scales are very popular with recreational fishers. The ability to weigh things reasonably accurately with a small inexpensive apparatus allowed for the exact weight of items to be ascertained. However, it was not accurate enough to weigh small amounts in ounces or grams.Scale. Has ring for hanging, spring and hook device for weighing. Measures in lbs.Scale of pounds weight.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Safety Eyeshields which were issued to protect the eyes from liquid irritant sprayed from enemy aircraft. during WWIIThese eyeshields were the property of one of the pioneer families in the city of Moorabbin. 2 One-piece transparent plastic eyeshield visor, mounted on green green fabric band that is secured by three metal staples. At each end of the fabric band is secured two lengths of black elastic, one end features a metal hook, the other a metal ring, and when joined secure the eyeshields to the wearer's head. The elastic straps are joined to the to fabric by metal pop studs, and these press down into two further pop studs located on the visor making the plastic bend to the shape of the wearer's face. Cardboard case is made of heavy duty card, open one end to form and envelope for storage. A felt material is attached as a cushioned nose strip. They are in a brown paper envelope and contained within a Cardboard case is made of heavy duty card, open one end to form and envelope for storage. There are printed with instruction on how to use them.Eyeshields, Anti-Gass, Mk. II. Air Spray Immediate action to be taken to prevent blisters - with instructions.world war ii, safety equipment, eye shields, anti-gas, eyeshields

This boat hook head is in very good condition and has been manufactured. It would be attached to a pole or handle to give it a long reach. A boat hook is a common piece of marine equipment and many have been made by boat owners to suit their own purpose. They would also have been forged byblacksmiths and shipsmiths and have been available from ship's chandlers over the centuries. A boat hook can be used for many situations such as catching mooring ropes and chains, reaching rigging, pulling things or people out of the water, and a variety of fishing applications.This boat hook head is an example of equipment carried on vessels over hundreds of years for safety purposes and for general applications. Marine boat hook head, all brass. The body is a conical shape with a pointed end and curved, horn-shaped hook moulded into the side. The body is hollow until it reaches the hook's height. A screw hole is close to the base, in line with the hook.flagstaff hill, warrnambool, maritime village, maritime museum, shipwreck coast, great ocean road, boat hook, marine, fishing, boating, equipment, boat hook head, rigging, safety equipment

Brown leatherette case containing ladies' sewing kit. Lined with flesh coloured moire silk, gathered pocket containing a sheet of 200 pins, brass thread holder containing 2 reels of silk thread, one shade 677 the other 706. Other half of case has leather strap with 2 packets of Lighthouse brand needles, scissors, thimble, two needles, punch, button hook, one unknown tool, 1loose '30's button, 2 needle cards, one containing 12 safety pins of various colours.Lithgow Sheet, 200 solid headed English Pins. Abel Morrall's Dress and Lingerie Pins. Art Silk Hose Mending, Flora MacDonald Needles are a Pleasure to Use.domestic items, sewing

Framed certificate for the Accreditation of the Ballarat Tramway Museum as a Manager of Rail Infrastructure and Provider and Operator of Rolling Stock. The certificate signed by the Acting Secretary Department of Infrastructure and Alan Ross, Director of Public Transport Safety. Framed with a wooden glazed frame, with a sheet of heavy cardboard and taped in. Certificate printed on preprinted paper - Certificate No. 37. Has a hook on the top.trams, tramways, rail safety accreditation, museum, btm

This item is from the "Barone" Collection. "Barone" (also known as "Seaview") was a stately Brighton home built at 9 Moule Avenue prior to 1855 and demolished in 1986. The house's residents included Edward Elgin Browne (during 1859-72), a Melbourne tea merchant, and the family and descendants of retired Scottish Army captain Archibald Black (during the period 1880-1970). Its neighbors included “St Ninians” owned by the Ward- Cole family, “Seacombe” owned by the Moule family, and the home of James Grahame and his family. The items in the "Barone" collection were largely donated by two of the house's later owners, Mrs Doris Halkyard and Mrs Brian Brandt.An English-made “Busvine” black wool herringbone twill riding habit comprising jacket and safety skirt, (jodhpurs missing) from late 1800’s to early 1900’s. The jacket (.1) features a black short pile silk velvet inset notched lapel collar secured with a single button at the apex of the waist and a single button near the collar for use in inclement weather. The sleeves join the bodice high on the shoulder with a full cut head to the sleeve and a tapered curved shape to the hand. The sleeve secures at the wrist with four black buttons. From the waist the jacket flares over the hip through princess line shaping and finishes with a curved front on either side. The seams of the shaping panels intersect single functional flapped besom pockets on either front panel. The back of the jacket features a centre back seam and two princess-line shaping seams that finish in a double vent on either side of the centre back. The jacket length would have finished approximately just below the bottom of the wearer. The apron fronted safety skirt (.2) secures from the waist at the front of the left thigh with five buttons. Over the wearers, right leg the skirt shapes to accommodate the rider’s right knee whilst sitting sidesaddle with her legs on the horses left flank. The base of the skirt has an elastic strap, which hooks around the rider’s leg to reduce the danger of the rider’s skirt become tangled, should the rider become un-seated. When the riders is not mounted the skirt can be secured with a button around the body to provide additional modesty as well as assist walking without the skirt dragging on the ground.Jacket: Manufacturer's label “Busvine, By serial appointment to Her Majesty The Queen, 4 Brook Street W.” Owner label “Doreen Wright” this label appears far more modern than the manufacturers label. Skirt: Manufacture's label: “J. Busvine and Co, 4 Brook Street, London W." In handwriting “Miss Wingfield” Manufacturers label: Busvines Patent Safety Skirt, protected by two separate patents. 4 Brooks St London West.barone, riding habit, j. busvine and co, seaview, brighton

The donor's mother, Joy Newall owned these kilts. She lived on a wheat/sheep farm in the Wimmera where her husband also bred merino sheep. Joy was well known in the district for the way she dressed when out in public.Maroon, brown, yellow and blue tartan kilt with eye and hook fastening clips and buttons on three different size settings. A metal clasp and large safety pin fastens on the left side.tag: Fletcher Jones / AUSTRALIA'S FINEST CLOTHING / MADE IN AUSTRALIAclothing, fashion, tartan, kilt, scottish, wool

The domestic sewing box would have been used in the home.A brown varnished rectangular wooden lidded Sewing Box with a lift out top section which has 16 varying sized compartments for storing sewing accessories. There is a has a hollow area underneath the tray. The lid is attached with brass hinges and it has a brass lock and small key. There are several sewing items included - cotton reels and thread, assorted darning thread for hosiery, wool and nylon threads, a box of black pins, assorted sewing needles, thimbles, small decorative sewing scissors, black rolled tape, mixed buttons, hooks and eyes, nickel plated fittings for hats, vintage stocking hooks, a stick of white chalk, two (one green and one ivory) antique cotton thread winders and a medium sized vintage safety pin.a Variety of brands of items include - 'Rite Tone', 'Della Darn' 'C No Darn', 'Clark's Filosheen' hosiery thread, 'Barbour's Linen Wax Thread', 'The Flora MacDonald Best Steel Bodkins' 'National Hat Guard' nickel plated steel and brass fittings, 'Chadwick's Wool and Nylon' reinforcing mending thread, 'The Myrene Snap Studio' size 1 rustless press studs, 'The Pagoda Brand' rolled tape 5 yds, 'Cross Fox Brand' Best quality Steel Stems (long plastic headed pins), 'Toledo' brass thimble and a black box of 'F. Tayler & Co's Solid Headed Mixed Pins'. The brass lock has 'SECURE PATENT' stamped in to it on the inside of the edge of the front of the box. there is also a small VR with a tiny rounded pattern opposite the Patent sign. sewing equipment, sewing box, sewing, embroidery scissors, functional object

Set of 14 duplicated newsletters printed on coloured quarto or foolscap duplicated paper, "Trammie Link" .1 - November 1978 - 1 quarto sheet - complaining about the lack of union leadership - published by a "tramways rank and file group" .2 - March 1979 - 4 sheets - training, shift work, Burke Road tram, route 72 tram, Gardiner, lifeguards, uniforms. .3 - April 1979 - 4 sheets - disciplinary panel, rosters, Camberwell depot, route 72, buses, North Fitzroy, Doncaster, Clifton Hill, Z class cars. .4 - May 1979 - 4 sheets - discipline, lifeguards, bus safety, union issues. .5 - June 1979 - 3 sheets - politics and unions, Preston depot, Camberwell depot, wage indexation, union matters, finance for public transport, Tramway Record. .6 - August 1979 - 10 pages- Preston Depot, item written by Jim Harper, public transport and government, hook turns, union meetings, women, ACTU, wages, shift work, rosters, depots, wage indexation, shift lengths. .7 - June 1980? - two pages - undated - Service cuts at North Fitzroy, depot committees, news from depots, and note re a meeting on Monday 7 July. .8 - July 1979? - 4 pages - strikes, union campaigns, depot management, industrial issues, discipline, depot facilities. .9 - Sep. 1980 - 3 pages - Lonie report, buses, closure, public transport, union, 35 hour week, unions. .10 - Oct. 1980 - 4 pages - union elections, industrial campaigns, 35 hour week, Lonie repot, public transport. .11 - Oct. 1982 - 3 pages - Preston workshops and new trams, new trams, W class trams, accidents. .12 - Undated - 2 pages about Paul Krutulis - a scab or an Agent Provocateur - see https://www.anu.edu.au/polsci/marx/interventions/years/11revival.htm - accessed 30-8-2016. - Extracted are the 4th and 5th paragraph below which give a bit of a background. .13 - July 1991 - 4 pages - open letter to Jim Harper re union Amalgamation, rank file view, what it would mean to workers - a negative view. Amalgamation was a major push of the Hawke - Keating Government. .14 - March 1992 - supportive of Jim Harper, dismissive of Lou DiGregorio, Union executive, union amalgamation, cross linking of tram routes, racial discrimination within the PTC, Kew Depot, ACTU. Lists the rank and file committee - see key associations. Latham’s frustrations were shared by several would-be heroes in Victoria. In 1977 Paul Krutulis gained an exemption from union membership from the Arbitration Commission as a conscientious objector, only to find that tramway workers at Kew planned to stop work as soon as he appeared. Commissioner Cohen then recommended his dismissal, saying she “had to deal with the reality of the situation.” Krutulis later became president of a group called People Against Communism, before being murdered in September. Thus Krutulis departed the scene to be followed in early 1978 by motor mechanic Jack Kane, who had crossed a picket line at a Melbourne City Council depot. The AMWU forced the Council to sack him before it would end the strike. In September of the same year, Barbara Biggs succeeded in provoking a confrontation in the tramways where Krutulis had failed, by refusing to join the union and prompting 100 unionists at Brunswick depot to go on strike. The union executive had arranged token action confined to this depot, but the members wanted more. The strike spread to Preston, then 2,000 trammies at a mass meeting voted for an indefinite strike amidst “rowdy outbursts”. When Biggs complained at being excluded from the meeting a conductress told her, “We should have let you in, love. You would have been torn to pieces.” Paul was murdered by his brother George in Sydney - see the Age 29/11/1977, but there seems to be some conspiracy theories abounding as well.Handwritten note / letter from Chris Jacobson.trams, tramways, unions, training, shifts, uniforms, route 75, gardiner, light rail, camberwell, z class, buses, discipline, tramway record, preston, north fitzroy, services, strike, depots, discipline, lonie report, public transport, preston workshops, rtbu, actu, ptc

The Aerial Drip Torch (ADT) was an idea conceived in Canada in the 1970s by John Muraro It was developed in 1982 by the New Zealand Forest Service to become the Ashley Aphid Helitorch. Forestry Tasmania acquired one of the machines and modified it in February 1987. Also known as a dragon helitorch it consisted of a large 135-litre tank containing jellied petrol, a displacement pump, propane ignition system, burner nozzle and fire extinguisher system. It was first trialled in Victoria at Swifts Creek in 1991 and the Aerial Drip Torch (ADT) has now become standard practice.Two Aerial Drip Torches (ADTs) were built in the 1990s by the Fire Equipment Development Centre at North Altona, They were developed in conjunction with the Department of Conservation and Land Management in Western Australia. The first was trialled during the 1991/92 autumn burning season. The machine proved to be successful and a second machine was introduced in 1998 to assist with burning operations across the State. The ADTs were commonly used for regeneration burning (controlled burning of logging slash). The first ADT introduced in 1992 had a dry weight of 160kg and a capacity of 130 litres, providing about an hour of operation. Following initial use, systematic modifications were adapted including improved ignition of gel at the drop tube, installation of an air bleed valve at the pump to assist pump priming and improved mounting brackets for the CO2 bottles and propane canister attached to the machine. The second, and lightweight ADT, introduced in 1998 had a dry weight of 68kg and a capacity of 200 litres due to a smaller lightweight frame and plastic (Polyfin) tank. In operation the ADT is suspended below a helicopter via four strops attached to the vessel and a cable to the helicopter cargo hook. Gelled fuel is dispensed via a drop tube which is attached to the pump outlet of the machine, and ignited via a gas torch. Safety features built into the first ADT were: a brass melting plug designed to be activated at 200 C bursting disc designed to burst at170 Kpa should the vessel over pressurise. a pressure relief valve set to 35 Kpa ( vessel operated between 16 &34 Kpa) a low pressure sensor designed to shut down the machine should the vessel pressure drop below 15Kpa. the vessel is filled with CO2 above the gelled fuel to eliminate ignition with in the vessel. CO2 is used to expel any residue of ignited gel from the drop tube to prevent ignition when flying outside the boundaries of the burning area. See FIRE EQUIPMENT NOTE - 46 [ https://drive.google.com/file/d/1CKtcH-3rUlrtbE9dkNP27PYT2-raVVhF/view ]forests commission victoria (fcv), bushfire, bushfire aviation, planned burning