Photo shows Victorian Railways tramcar No. 42 and 33 at Elwood depot. Bogies or trucks are of the Brill 77E type. Note the oil lamp on the driver's dash panel - all VR trams carried them.Yields information about the Victorian Railways bogie trams.Photograph - Black and White - VR 42 and 33 at Elwoodtramways, trams, victorian railways, vr trams, elwood depot, brill 77e, tram 42, tram 33

It is unknown how this came into the collection at the Warrnambool Museum. However, during the 18th and 19th centuries it was fashionable for young men of means to undertake a 'grand tour'. During their travels they would often pick up souvenirs with these sometimes being ancient artefacts from classical Greece or Rome. It is thought that the item most probable came to the museum in this manner.From discussion with specialists at the British Museum and the University of Reading it was ascertained that the oil lamp is indeed ancient Roman and over 2000 years old. The marking on the top could be Venus although it is quite worn away so it is difficult to tell for sure.A terracotta oil lamp housed in a wooden box. On the top of the lamp are 3 circle incisions and in the centre of the circles is a depiction of a figure. There is a small finger sized handle on the side of the lamp. The handle has 2 incised lines leaving 3 raised ridges. It is squared off at the top. The top of the oil lamp has a hole in which to place a cloth wick and a spout from which the smoke would have come out. The spout is blackened from smoke. The container box is guessed to be from the time of acquisition which would be around the early 1900s and is made from a polished wood. Light in colour.In the box was a label saying, 'Venus coming out of the gate of the temple'. It also stated that the lamp may have been placed at the feet of the dead in the catacombs.oil lamp, roman, terracotta, classical, archaeology, victorian, grand tour

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. This particular lamp has the design of the early kerosene lamps. Its gimbal bracket and counterweight heavy base allow it to swing with a vessel's movement and still stay horizontal. The lamp is significant for its design which is an example of a 19th and early 20th-century kerosene lamp with a wall-mounted gimbal bracket and counterweight base. These features were important to vessels at sea, allowing the lamp to swing with the vessel's movement and stay vertical on rough seas.Kerosene lamp; round electroplated metal top and base, both shaped inward to join together. The base is a solid counterweight to work with the gimbal wall attachment bracket. There is no glass cover.shipwreck coast, flagstaff hill maritime museum, flagstaff hill maritime village, warrnambool, flagstaff hill, kerosene lamp, lighting, marine lamp, kerosene lantern, lamp, lantern, marine equipment, wall gimbal, wall mounted lamp, ship lamp

Sherwood Ltd. Was a manufacturer of oil lamps and burners at the Nechells Park Works Birmingham UK and regarded at the time as a renowned name in the oil lamp and burner manufacturing industries in Birmingham during the early part of the 20th century. They started selling as ‘Isaac Sherwood & Son Ltd.’ in 1904, later around 1920 they merged with Linley and Co makers of American pattern lamps and became ‘Sherwood-Linley” moving to 44-50, Granville St. Birmingham. They became one of the largest manufacturers of lighting devices and burners in England. They produced all sorts of illumination devices and became famous for their oil burners. Apart from oil burners, they produced table and floor lamps, sconces, lanterns and chandeliers that made Sherwood unique. A Significant item as part of a kerosene lamp that was commonplace in homes and other premises during the early 20th century as a means of lighting before electric lighting became the standard. These types of items give a snapshot into domestic and social life during this period.Lamp Burner housing, brass with wick-screw (no wick). Made in England Sherwoods LTD Birminghamwarrnambool, flagstaff-hill, shipwreck-coast, flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp burner, sconces, kerosene lamp, wick adjuster, sherwood & son ltd, sherwood-linley

Photograph of tram 53, shows the Victorian Railways colour scheme, the oil lamp that was provided on VR trams on the St Kilda to Brighton, Electric Street Railway. The tram is shunting at the depot or waiting to run to St Kilda Railway Station possibly after the closure of section south of the depot. Photographer not recorded. Yields information about the location, the streetscape and the trams in use at the time. Black and white photograph of Victorian Railways tram 53 outside Elwood Depot in St Kilda St, possibly in the late 1950s.tramways, trams, vr trams, elwood tram depot, st kilda st, victorian railways, tram 53

This lamp would have been attached to a coach, or even an early automobile, for lighting purposes. It could also have been used for outdoor purposes in a household or business setting. Lamps such as this were used in the 19th century and early 20th century and preceded or accompanied the use of oil lamps and were later superseded by electric and gas lighting.This item is of historical interest and is retained for display purposes.This is a rectangular-shaped lamp made of metal. It is painted black and has clear glass with bevelled edges on two sides and a small round red-coloured glass on another side. The lighting mechanism inside the glass appears to have held a candle. The body of the lamp is mounted on a solid round metal pipe. There is a metal handle at the top for attaching the lamp to a wall or stand.vintage lighting, coach lamps

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. An anchor lamp like the lamps in this pair would be raised on the highest ship mast at night to signal other seafarers that the ship was at anchor or sailing at night. The metal loops on opposing sides of the lamp could hold a pair of rods or ropes. and be used to raise the lamp.The lamp is made to the design of a 19th and early 20th-century kerosene anchor lamp carried as essential marine equipment and used as a signal lamp on sailing ships. Lamps; a pair of cylindrical kerosene anchor lamps. Each has a flat back, a hinged door, a metal handle and two metal loops or guides fixed on each side. The glass window is convex and inside the lamp is a wick in an enamel wick holder.brass lamp, lamp, anchor kerosene lamp, kerosene lamp, marine equipment, marine lamp, navigation, light, ship light, ship lamp, lantern, maritime, nautical, safety lamp

Timber framed oil on canvas. Painting depicts a woman sitting at a table reading a letter (her back to viewer). To her left on the table is a framed photograph of a WWII soldier, immediately in front of him is a poppy and behind him to his right, is a mantel radio and to his left, an oil lamp. Timber framed oil on canvasPlaque "Lilydale Art Society Inc / Spring Show Nov 18 & 19 1995 / "Australia Remembers 1945-1995" / Art Competition / 1995/ 1st Prize / Sponsored by Lilydale Sub Branch RSL / and "Australia Remembers 1945-1995 Assoc."

Photograph of tram 37 shows the Victorian Railways colour scheme, the oil lamp that was provided on VR trams on the St Kilda to Brighton, Electric Street Railway. Has 3 Robur Tea roof advertisements. The tram is shunting at the depot or waiting to run to St Kilda Railway Station, possibly after the closure of section south of the depot. Original Victorian Railways Photograph. Yields information about the location, the streetscape and the trams in use at the time. Black and white photograph of Victorian Railways tram 37 outside Elwood Depot in St Kilda St, possibly in the early 1950s. Original Victorian Railways Photograph.tramways, trams, vr trams, elwood tram depot, st kilda st, tram 37, victorian railways

List of deceased local TOC H men who passed during World War 2. Historical. ResearchBronze PlaqueEastern oil Lamp with cross, on top of plaque. 1939-1945. Text below reads 'WITH PROUD THANKSGIVINGG WE REMEMBER THE GOOD FELLOWSHIP OF LOCAL "TOC H" MEN WHO JOINED THE RANKS OF THE ELDER BRETHREN DURING THE WAR.' 4 Wall mounting holes, 1 in each corner.ww2 memorial

Isaac Sherwoods Ltd were manufacturers of oil lamps and burners in Birmingham, in 1904 they were trading as Isaac Sherwood & Son Ltd. but by 1920 they had taken over Linley & Co. of 73-75 Great Lister Street, makers of `American' pattern lamps to become Sherwood-Linley at Nechells Park Works, Eliot Street. The company were a leading manufacturer of oil and candle lamps exporting their goods all over the world. The subject lamp is operated with a candle, which is inserted on the underside, it is sprung and as the candle burns the spring keeps the candle pushed upwards keeping the flame burning until the candle is extinct. Sherwoods invented and patented this innovation for candle lamps.The subject item is incomplete however it has some significance as it was designed to be used in a sea going vessel, as a result is quite rare also the item is made by a well known manufacturer.Spring loaded candle Lamp, brass, with gimbal wall attachment for use on a ship, shade and mount missing. Candle-stop has the words "Sherwoods Limited, trademark sound".flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, candle lamp, gimbal spring, sherwoods limited

This lamp pattern was originally made in USA between 1880 and 1900. The pattern is called Feathered Cartouche and generally had a painted motif on each of the panels on the front. This lamp is probably a copy of the American lamp and made in Australia sometime in the first half of the 20th century. The lamp has an English style collar rather than an American one and the pattern is not as crisp as the American ones. There were several lamp patterns made here that were copies of American patterns and that style of collar was used on most of them. (ref Oil Lamp Antiques)This item is an important example of the early technology of artificial light. It has historical significance in demonstrating lighting devices used before the widespread use of electricity.Ornate clear glass kerosene lamp. Glass chimney is missing. Base is square and patterned with raised oval shapes, as is the stem. Both base and stem are hollow. At the top, the kerosene holder is squarish with round corners.. The wick holder is of brass and has a small wick adjustor.lamp, kerosene lamp, lighting - domestic

Photograph of one of the three Victorian Railways "Luxury" cars that were sold to the MMTB following the closure of the final section of the St Kilda - Brighton tramway on 28-2-1959. The tramcar has been placed on No. 15 trucks to enable movement around the workshops. Two of the trams, No. 52 and 53 were modified with longer running boards, full driver's bulkheads to replace the blackout blinds, route number boxes, removal of the red oil lamps above the headlight, conversion to from Broad gauge (5'3") to standard gauge, changes to destination boxes, seating and many other changes. Reference Destination City, Edition 5, page 103.Yields information about the former VR "Luxury" trams sold to the MMTB in 1959.Black and white photograph of one of the three Victorian Railways Trams sold to the MMTB at Preston Workshops.tramways, mmtb, trams, victorian railways, st kilda brighton electric tramway, preston workshops, vr class

This Christian Bible by Professor James Moffatt from the United Free Church College in Glasglow Scotland was at a time when translated Christian bibles(Greek to English) were being review as to the accuracy of their translated words. This period was in the early 1900's specifically during and between the two major World Wars of 1914-18 and 1939-45 and also covering the Great Depression(1939). All these periods were ones of death, destruction and "loss of faith". Bibles which provided greater clarity of better times ahead flourished. This book offered its readers hope for the future (in terrible times). The regions that it covered were those who belonged to the Christian Faith. The significance of this bible to the Kiewa Valley is that it provides an insight of those Christians living in a semi remote rural region at the period in Australian history where forces outside of this area were placing hardships which were "foreign" to them, as a family and as a community. The major Christian religions within the Kiewa Valley were either of the Catholic or English Protestant teachings. These groups still remain the dominant ones well into the 2nd Millennium. Spiritual relief to overcome harsh rural setbacks is not just specific to the Australian rural sector but is also global. With the influx of migrant workers from the war torn European nations (after WWII) a broader coverage of Christian and other faiths developed. A "positive" saying, when crops failed and bush fires and river floods sprang up, rallied the faithful "with God's help" This hard covered bible consists of six pages of preamble including title, publishing details, printer and author's preface. The book has 388 pages of black print. Relevant reference lines are notated by numbers on the left side of the page. On the front dust cover is a cream silhouette against a light blue backdrop highlighting a smoking "Aladdin's" Arabic oil lamp on a cenotaph. The hard cover has a embossed emblem of a lantern with a plume of smoke rising from the spout. This is all encapsulated by a circle. The spine also has this emblem. On the dust jacket, front "THE MOFFATT NEW TESTAMENT", and the back cover has blue writing on a cream background. On the spine, at the top "JAMES MOFFATT" below this a white on blue silhouette of "Alalddin's lamp" below this is (in blue letters against a light blue background " THE NEW TESTAMENT A NEW TRANSLATION" On inside cover a signature "Clare Roper". The hard cover has marked in red print "THE NEW TESTAMENT ANEW TRANSLATION MOFFAT" christian bible, prayer, new testament, religion, faith.

Kempthorne Lighting Pty. was established as Coffey Lanterns in East Malvern, Melbourne Victoria in 1931 by brothers Selwyn and Owen Coffey. They manufactured lighting fixtures and fittings including oil lamps for marine use as well as for the domestic market. In early 1936 two other brothers, Erle and Terence had joined the company which was renamed Kempthorne Lantern Works Pty., Ltd. In 1946 Kempthorne joined with a small design team who had developed a domestic fan to form the subsidiary, Mistral fans. The company previously known as Kempthorne Holding Ltd was listed on the stock exchange in 1968. In 1977-1979 Kempthorne Mistral Ltd. Was a holding company comprising of Kempthorne Lighting Pty., Ltd. & Mistral Fans Pty., Ltd. An early Australian made marine lamp by a significant manufacturer that is still in business today making electrical equipment. The item is an important artefact that was made by an early Australian business that started in the 1930s. Over the years this company has demonstrated many innovations to the manufacturer of electrical items. Marine copper Lamp, round with brass makers lozenge and rounded hollow lugs set on either side of the lamp. Heavy metal handle with brass locking pin. Lid with catch on top. Made by Kempthorne Pty Ltd Melb. 1941flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, copper ship lamp, ship lamp, kempthorne pty ltd

This trade mark (V inside a clover) was German. It was used by the lamp makers Veritas Efsca Works in Birmingham, and for a time by Valor Co. Ltd. which took over Veritas. Valor Co. Ltd. was established in Birmingham in 1890 and produced oil containers for the Anglo-American Oil Com. In 1901 the firm advertised themselves as Stampers And Pieces. Later it was named 'The Valor Co. and was associated with the Aston Brass Co., and advertised as makers of oil lamps and stoves. Valor became a maker of oil heaters cookers and many other products that were fueled by oil. Later it sold gas heaters and ovens. In 1936 Valor Co. Ltd. was made a Public Company and operated under the name The Velor Company Ltd. The company changed names over the years and it was still operating under Velor Fires in January 2002.Oil or kerosene lamps were the means of lighting for homes, farms and industry in the late 19th and early-to-mid 20th centuries. Lamps like these were important as Lighthouse Keepers and Assistant Keepers' equipment. They were in common use in until the lighting was powered by gas and electricity. The reflector at the back of the lamp makes it of greater significance as most lamps don't have this feature. The logo is also interesting as it originated in Germany and was used with permission by a British company and the company that brought it out for a short time. Similar lamps are still available today, usually with gas for fuel. Kerosene lamp; blue painted metal fuel can and metal rear reflector support. and a round corrugated reflector at the rear. The mid-section wick is made of brass. The glass cover or chimney is bulbous in shape. Inscriptions include a trademark "V" inside a clover. It is British-made in Birmingham by either Veritas Efsca Works or Veritas Valor.Trademark; "[clover symbol] surrounding a "V" Stamp: "BRITISH MADE" Marked on adjusting device: "English Made 1 in w" Marked on support of deflector shield - "British Made" and symbolwarrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, oil lamp, table lamp, kerosene lamp, valor co. ltd, v inside a clover, veritas, british made, lamp reflector, lighting, lamp, the valor company ltd

Oil burning Tail-lamp for a (1917/23) model Ford T Model Motor Car in unused condition. Mounted on a varnished wooden block mount.Faintly engraved on top "Ford" Faintly engraved on bottom "PAT MAY 26 -14 PAT JUN 23 - 14 PAT NOV 23 - 15 PAT DEC 21 - 15 PAT NOV 7 - 16 PAT AUG 28 - 17" On front of Timber Mounting "Donated by Jim Dowton Sale FORD - Model T 1917 - 1923 Tailamp - part 6568x" On back of timber mounting "ON LOAN J.DOWTON SALE TAIL-LIGHT 1912 - 1919 T MODEL FORD"1920, 1918, 1919, 1917, 1923, ford, tail light, tail lamp, henry ford, t model, ford car, kerosene lamp, 1921, 1922, 6568x, part number 6568x, dowton

The Kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. The Anchor Lamp design was used for marine purposes in the days of sailing ships when a ship at anchor or sailing in the dark was required to display a white light on the top of its main mast. The Anchor Lamp's top loop was for a rope to hoist it up the mast, and ropes through the two bottom loops to anchor it in place and prevent it from swaying. The light could be seen by ships up to 20 miles away due to the magnification of the Fresnel glass lens. This lamp in our collection has a design is similar to the early marine designs but its finish and materials resemble lamps made in the 20th century to represent the older ones. The etched "20" on its cover could represent the 20-mile distance the light could shine, and the "↑" Broad Arrows could represent a maritime navy ship. The lamp is an example of 19th and early 20th-century Anchor Lamps fueled by kerosene and used onboard ships when at anchor or sailing at night.Kerosene lamp; This Anchor Lamp design has a brass frame, a handle with a loop at the top, a rail around the base two opposing loops, and a kerosene burner and tank with ventilation holes around it. A clear glass Fresnel 360-degree lens covers the burner. It is an All Round design. The brand Anchor is inscribed on a plate fixed to its brass cover. An etched inscription on the cover includes the Broad Arrow symbol identifying government property.Engraved plaque: "Anchor" brand. Etched into the metal: "↑20↑"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, kerosene lamp, lighting, ship light, anchor lamp, marine technology, marine lamp, 20 mile light, broad anchor, oil lamp, whale oil lamp, ↑

This lamp is typical of lamps used in Welsh Coal Mines. It was purchased from the supplier around mid 1995. The Welsh Miners’ Lamps were ingeniously designed over 180 years ago to alert coal miners to danger. It ensures the burning of a protected flame in the presence of explosive gas, by regulating the necessary supply of atmospheric air, and by allowing the products of combustion to pass through without igniting the gaseous atmosphere. If the atmosphere is so heavily charged that noxious gas enters the lamp, its presence will be indicated by a change in the length and color of the flame, and (unless there are exceptional circumstances), the miner has sufficient warning to secure his safety. (http://www.welshminerslamps.com/info_lamp_personaluse.shtml, accessed 06/05/2015) E. Thomas & Williams, Ltd. mining lamps have been in continuous production since 1860. Cambrian Lamps are approved for use in coal mines where methan gas and oxygem deficinecy are hazards.Solid Brass traditional miners Flame Safety Lamp with Copper Chimney. The base of this lamp is tooled from solid brass because brass does not spark when it hits rock and is therefore the safest metal to use underground. The lamp burns lamp oil (kerosene). R. Thomas and Williams Ltd Makers Aberdare Wales Cambrian No 152897mining lamp, miner's lamp, thomas and williams, wales, welsh, welsh miners lamp, mining, cambrian lampworks, miners flame safety lamps

8HP Blackstone Lamps Start Oil Engine engine number 71076 Engine Details Maximum operating RPM of 240. Fitted with a 3'9" Flywheel Tested on the 6th of November 1908. Shipped to Cluter buck South Australia for installation on concrete base. Recovered and restored during the 80's in South Australia Purchased privately in 2013 in Tailem Bend South Australia and transported to Victoria. Currently on loan to the Puffing Billy Museum at Menzies Creek as an operating exhibit. Blackstone & Co. was a farm implement maker at Stamford, Lincolnshire, United Kingdom. In 1896 they built lamp start oil engines. The Lamp or hot-bulb engine (also hotbulb or heavy-oil engine) is a type of internal combustion engine. It is an engine in which fuel is ignited by being brought into contact with a red-hot metal surface inside a bulb, followed by the introduction of air (oxygen) compressed into the hot-bulb chamber by the rising piston. There is some ignition when the fuel is introduced, but it quickly uses up the available oxygen in the bulb. Vigorous ignition takes place only when sufficient oxygen is supplied to the hot-bulb chamber on the compression stroke of the engine. Most hot-bulb engines were produced as one-cylinder, low-speed two-stroke crankcase scavenged units Historic - Industrial - single cylinder, horizontal, 4 stroke, hot-bulb ignition oil engine Blackstone 8HP Oil Engine made from steel, wrought iron and brassOval Plate with Black Stones and Clutter Buck Brass Plaque engine number 71076blackstone, oil engine, clutter buck, black stone, puffing billy, hit and miss, engine, blackstone & co