Victorian Railways Memorandum, dated 30-11-1906 on VR printed form Z 183a, advising Porter (?) G. H. Biquell (?) that he had been transferred to the position of Conductor on the St Kilda Brighton Electric Tramway from 1/12. He was to report to Mr. Bradford at the Power Station, Elsternwick. Signed by J. Keane Acting Station Master West Richmond station. Has been completed using a form with a perforated edge on the left hand side.trams, tramways, victorian railways, st kilda brighton, conductors, personnel, elwood

Buff coloured booklet. Front cover ' Victorian Railways Instruction Book, concerning the Locomotive and the Westinghouse Brake for engine cleaners, Melbourne, August 1935' Inside front cover in blue ink ' J. Badham, Maryborough 27/10/48. Seymour 11/10/48'.Victorian Railwayscottage, miners, badham, victorian railways, locomotive

Victorian Railways Magazine, November 1928, (46 pages, centre stapled) without covers. Has a number of railway articles including Safety, Aviation in Australia, roller bearings in passenger carriages, Metal of the future - Aluminium. On page 8, is a photo titled "A City's Gateway", photo taken looking out from under the clocks from within the railway station , across to St Pauls Cathedral with K 92, a W2 and W1 in the photograph, along with some ladies. Shows the stained glass windows. Photo by A. L. Reid.trams, tramways, victorian railways, flinders st station, tram 92

Issued to employees of the VR St Kilda to Brighton electric street railway, superseding previous copies. The line closed in 1956. Note the spelling of the word "employe" with an accent over the e - an acceptable practice in Victoria at the time - a US based spelling. Book scanned into multiple parts. See Reg Item 3508 for a "Supplement to the Book of Instructions re the working of the St Kilda and Brighton Electric Street Railway, dated 1/1/1915", item 7518 for a June 1907 version, and 7580 for instructions issued in 1911.Demonstrates a Victorian Railway Rule book for electric tramways or Street Railways.Rule Book - 156 pages, five sewn sections within a green coloured Rexene heavy card with glued endpapers with the title "Victorian Railways Instructions re Working of the St Kilda and Brighton Electric Street Railway" and "1927" in gold block. Dated 1 June 1926. Has a table of contents and index - gives definitions - "trams" vs "street railways", general instructions, hand signs, working of cars, working of traffic over single and double line, staff and ticket systems, air brakes, permanent way, overhead, fares, appeals of employees against penalty and electric shock.Copy 3 has stamp of the "Westinghouse Brake Inspector" and "Lloyd Rogers" in ink on the inside front cover. On page 94 and 95 has notes in pencil about the air braking system - may have been for a following issue.trams, tramways, victorian railways, vr, st kilda brighton, rules, employees, safeworking

A large collection of Victorian Railways Newsletters dating from 1962 to the late 1980s. Each booklet is 19 pages a features a combination of articles, illustrations and news items.fictionThese booklets document development and news items from Victorian Railways from 1963 until the late 1980s. During this period the corporate name changed to VLine but the newsletter continued to be published as VLine Newsletter. The newsletter continues to be published for employees of VicRail in the 2020srailways victoria, railways newsletter

Victorian Railways 280HP Walker RailcarVictorian Railways livery circa. 1968victorian railways, railcar

280HP Walker Railcar Victorian RailwaysVictorian Railways livery circa. 1968victorian railways, railcar

NKS Type Gangers Trolly - Victorian Railways 2'6" gauge trolley - a KS series Section Car oftern called the Kasey Jones The narrow gauge version of the broad gauge KS series cars. They were classed NKS with two stroke motors. These cars were built by the Spotswood Workshops, with castings coming from the Newport Workshops. KS is lighter car capable of carrying 4 men or sevenhundredweight Trolly 9 was built for the State Electricity Commission of Victoria for use on their metre gauge railway of Yallourn. It was sold to a preservation group at Walhalla and regauged to 2 foot 6 inch. It came to the Puffing Billy Railway in the early 1980s.Historic - Victorian Railways Narrow Gauge - Track Patrol Vehicle used by the State Electricity Commission of Victoria for use on their 900mm gauge railway of Yallourn. And then at Walhalla Railway where it was regauged to 2 foot 6 inchMotorised small rectangular trolly made of wood and wrought iron - currently stored dismantled Engine Type: 1 Cyl. reversible Fuel: 2 stroke Transmission: Belt driveNKS 9puffing billy, puffing billy museum, trolley, narrow gauge, 2'6" gauge, victorian railways, state electricity commission of victoria - yallourn., trolly

Report - stapled and bound within blue light card covers, 118 pages + 10 photo pages + 5 diagram or graph pages + fold out map titled "Victorian Railways - Report of the Victorian Railways Commissioners for the Year ended 30th June 1925". Has a With Compliments slip on the inside front cover. Note: This document is available as a pdf on the Parliament of Victoria website.trams, tramways, railways, finances, financial statements, annual reports, costs

Victorian Railways Bread Plate - Black & White Maker : W H Grindley & Co (Ltd) Earthenware manufacturer at the Newfield Pottery and then the Woodfield Pottery, Tunstall, Stoke-on-Trent The company was founded at the Newfield Pottery in 1880 by William Harry Grindley (princliple partner) and Mr Turner (the '& Co.') They produced Earthenware and Ironstone China - particularly for the Canadian, United States, South American and Australian markets. In 1891 the company moved to the Woodfield Pottery, Woodland Street, Tunstall. In 1960 the business was purchased by Alfred Clough Ltd. In 1978 renamed Grindley of Stoke (ceramics) Ltd. Federated Potteries Co. Ltd. took them over in 1982 and in 1988 the business was re-purchase by W. H. Grindley. 1991 saw the company in the hands of the receivers. and the same year they were taken over by Woodlands Pottery. DURALINE (trade mark) printed mark used by Grindley Hotel Ware Co Ltd c.1930's onwards The Number i.e "6-53" = "month-year" Supplier to Victorian railways : Loftus Moran, Melbourne: Mr Loftus Henry Moran was well known in the tea trade. Originally employed by Griffiths Bros Ltd, he started his own business, Loftus Moran Pty Ltd, in 1909 In 1913 he purchased the tea business of Mcintyre Bros, and later' that of Steele Bros, and absorbed them in his own company. He had a wide business connection among hotels and guest houses for supplying crockery and other supplies. Ref: DEATH OF MR LOFTUS MORAN (1944, May 27). The Argus (Melbourne, Vic. : 1848 - 1957), p. 4. http://nla.gov.au/nla.news-article11809686 1st Advertisement of the Plates in the papers: CHIPPED CROCKERY. Nothing is more objectionable than chipped crockery--besides its use is illegal. DURALINE Plates, manufactured by The Grindley Hotel Ware Co., are tough as raw-hide. This is why they are used by practically every hotel and institution in Australia. Obtainable only from LOFTUS MORAN PTY. LTD., Hotel Supply Specialists, 131 Queen's Bridge Street, Melbourne South Advertising (29 March 1933, ). The Argus (Melbourne, Vic. ), p. 7. http://nla.gov.au/nla.news-article4726734Historic - Victorian Railways - Refreashment Services crockery - plateceramic Victorian Railways Bread Plate - Black & White Victorian Railways ( in black on fount of plate ) "DURALINE" ( in Black on back of plate ) super Vitrified GRINDLEY HotelWare Co England Loftus Moran Pty Ld Melbourne 8 -53puffing billy, victorian railways, crockery, plate

Victorian Railways 153hp Walker Railcar 32RMVictorian Railways livery circ 1955victorian railways, rail car

3A Built in 1900. This is the second locomotive to be built at the Victorian Railways Newport Workshops. Painted in the then standard Victorian Railways two-tone green, this locomotive was issued to the Upper Ferntree Gully to Gembrook line and was used on the line’s construction. Over the years, it saw service on the Colac to Crowes and Moe to Walhalla lines, but it saw more service on the Gembrook line than any other. It was withdrawn from service in 1955 at Upper Fern Tree Gully and sold in 1960 to the Lord Mayor’s Camp at Portsea where it remained on static display until obtained by the Puffing Billy Presservation Society in 1977. Number 3A Entered service 6th april 1900 Livery two-tone green Gauge 762mm / 2' 6" Service History : Apr 1900 UFTG. - initial allocation Apr 1900 - Jul 1901 Upper ferntree gully Feb 1902 - Jan 1906 Colac Feb 1906 - Jul 1906 Upper ferntree gully Sep 1907 - Mar 1908 Colac Oct 1908 - Oct 1909 Upper ferntree gully Nov 1909 - Apr 1910 Other Oct 1910 - Nov 1911 Upper ferntree gully Feb 1912 - Oct 1914 Colac Dec 1914 - Oct 1917 Moe Dec 1917 - Jul 1920 Colac Sep 1920 - Jun 1922 Moe Jul 1922 - Jun 1925 Upper ferntree gully Aug 1925 - Mar 1928 Other May 1928 - Nov 1929 Moe Jan 1930 - Apr 1935 Wangaratta Jun 1935 - Sep 1936 Workshops Oct 1936 - May 1949 Upper ferntree gully Nov 1949 - Mar 1950 Workshops Apr 1950 - Jun 1955 Upper ferntree gully Nov 1955 - Mar 1959 Workshops Nov 1960 - Aug 1973 Lord Mayor’s Camp at Portsea Apr 1977 - salvaged from Lord Mayors camp and delivered to Menzies creek station.Victorian Railways - Narrow Gauge NA class steam locomotive number 3A Victorian Heritage Register (VHR) Number H2187 Dates that 3A worked on the Upper ferntree gully to Gembrook Line. Apr 1900 - initial allocation of a new locomotive Apr 1900 to Jul 1901 Feb 1906 to Jul 1906 Oct 1908 to Oct 1909 Oct 1910 to Nov 1911 Oct 1936 to May 1949 Apr 1950 to Jun 1955 Apr 1977 to Belgrave Steam Locomotive3Apuffing billy, victorian railways, 3a, narrow gauge, steam locomotive

During prestige, long distance train journeys some carriages had air-conditioning, and the majority of passengers had to brave unheated carriages. To offer some comfort during the winter months, the non-air-conditioned carriages were provided with footwarmers. These were metal containers roughly 100 mm thick and 300 mm wide, and about 750 mm long, which were filled with salt crystals (concentrated crystalline hydrated sodium acetate). The footwarmers were covered by sleeves of thick canvas, and two footwarmers were usually placed in each compartment of non-air-conditioned carriages. To activate the chemicals, the footwarmers were heated almost to boiling point. This was done by removing the canvas sleeves and placing the footwarmers in a large bath of very hot water. After they had been heated, they were removed from the bath and the sleeves refitted. They were then ready to be placed in the carriages. The McLaren patent foot warmer was used on railways in New South Wales, Queensland, Victoria and South Australia as well as South Africa and New Zealand. It was during the 1901 royal visit by the Duke and Duchess of Cornwall that these foot warmers were first used in New Zealand in the royal carriage. Before railway carriage heating was introduced, McLaren patent foot warmers were placed on the floor of New South Wales government railway carriages from 1891 to provide a little passenger comfort. The rectangular steel container worked a bit like a hot water bottle but instead of water contained six and a half kilograms of loosely-packed salt crystals, (concentrated crystalline hydrated sodium acetate). This was permanently sealed inside the container with a soldered cap. After the foot warmer was heated in vat of boiling water for about one and a quarter hours the crystals became a hot liquid. (The melting point for sodium acetate is 58 degrees). There was a whole infrastructure of special furnaces set up at stations for the daily heating of foot warmers. By 1914 the Victorian railways had 4,000 foot warmers in service and by 1935 there were 33 furnaces at principal stations to heat them. After about 10 hours the container was picked up by the handle and given a good vertical shake which helped the cooled liquid reform into a solid mass of hot crystals. Staff or sometimes passengers shook them en route when the foot warmers began to get cold. However, as they were heavy this was only possible by fit and agile passengers. At the end of the journey the containers were boiled again for reuse on the next trip. Sodium acetate railway foot warmers were introduced in Victoria in 1889, Adelaide to Melbourne express in 1899. "Shaking up" on this service took place at Murray Bridge and Stawell on the tip to Melbourne and at Ballarat and Serviceton on the trip to Adelaide. The use of foot warmers began to decline in New South Wales from the 1930s with the first trial of carriage air-conditioning in 1936, steam heating from 1948 ad LP gas heating from 1961. By the early 1960s the main services using foot warmers were the overnight mail trains. info from : http://www.powerhousemuseum.com/collection/database/?irn=67564#ixzz4UBNzVf6t Under Creative Commons License: Attribution Non-Commercial There was a whole infrastructure set up at stations for the daily heating of foot warmers in special furnaces. In Victoria alone in 1935 there were 33 heating works.Historic - Victorian Railways - Carriage Heater - Foot warmerA rectangular-shaped stainless steel casing with a welded seam down the back and welded ends. There is a handle at one end for carrying and shaking. Inside the foot warmer are two baffle plates and three trays to contain the sodium acetate. There was a cast-iron ball in each internal compartment. puffing billy, victorian railways, carriage haeter, foot warmer, passenger comfort, station furnace, railway ephemera, early heating methods

The Victorian Railways jacket would have been part of a uniform for railways employees.The Victorian Railways jacket has local significance as it was donated by a Wodonga resident. It also has historic significance due to its relative rarity and representativeness as part of the uniform worn by Victorian Railways staff, as it is in relatively good condition.Blue Victorian Railways jacket, with the VR logo stitched on each lapel and silver buttons."VR" logo stiched onto the lapels of the jacket victorian railways, vr, victorian railways uniforms, railway uniforms, victorian railways jackets, v.r.

The Wodonga line and train station opened in November 1873 when the section of the line from Wangaratta was completed. The expansion of the railways to the northeast of Victoria occurred after the Victorian Government took over the railways in 1867 and the trains serviced large towns such as Seymour, Wangaratta and Wodonga, as well as smaller towns along the way. The first section of the Wodonga to Tallangatta line opened in 1889 and was further extended in 1891. It was a vital community link until the passenger service closed in September 1961 The last regular goods train on the line ran on 21st April 1978. The north- east train line to Wodonga remained a significant factor in the development of Wodonga as a rural city in the 20th century. Local significance due to the importance of the railways to Wodonga as a means of transport, communication and impact on business and commerce. State and national significance due to the role played by the railways in opening up the country for development.A bound volume of the Victorian Railways Time Table for 2nd May 1910 to 30th November 1910. Black with gold inscription. The binding is not original but was carried out to preserve the contents"Victorian Railways/Time Table/ 2nd May 1910/ 30th November 1910"victorian railways, wodonga, timetable, transport

Victorian Railways Diesel Electric Rail Motor 63RMVictorian Railways livery as per 1934 painting diagramvictorian railways, diesel electric, rail motor

7A Built in 1905 and painted Canadian red & dark brown, this locomotive was issued to the Wangaratta to Whitfield line and saw service on all four lines with most of its service on the Upper Fern Tree Gully to Gembrook line. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it has seen almost continuous service since. 1979 saw the early two-tone green colour scheme applied to this loco as a trial even though it never historically carried it, but its physical configuration was not altered accordingly. It is now painted its original livery of Canadian red & dark brown and will eventually be returned, as far a possible, to its original condition with a low bunker, narrow ash-chute, etc. Loco: 7A In service Saturday, 6th May 1905 Livery Canadian red & dark brown Owner Puffing Billy Gauge 762 / 2' 6" Status Preserved - Operational Service History : May 1905 Wangaratta - initial allocation of a new locomotive May 1905 - Apr 1906 Wangaratta Jul 1906 - Nov 1910 Colac Feb 1911 - Jul 1912 Moe Sep 1912 - Dec 1917 Colac Mar 1918 - Sep 1921 UFTG. Nov 1921 - Sep 1923 Colac Dec 1923 - May 1925 UFTG. Jun 1925 - Aug 1925 Workshops Sep 1925 - Aug 1927 UFTG. Aug 1927 - Feb 1928 Workshops Mar 1928 - May 1928 UFTG. Jul 1928 - Moe Sep 1928 - Mar 1930 UFTG. Apr 1930 - Sep 1930 Workshops Oct 1930 - Oct 1936 UFTG. Nov 1936 - Moe Dec 1936 - Aug 1945 UFTG. Dec 1946 - May 1953 Colac Sep 1953 - Oct 1954 Moe Dec 1954 - Jun 1955 Workshops Nov 1955 - Dec 1957 UFTG. - Stored Feb 1958 - Apr 1962 Workshops May 1962 - Belgrave - In active service at Puffing Billy Railway Belgrave Victorian Railways - Narrow Gauge NA class steam locomotive number 7A Dates that 7A worked on the Gembrook Line Mar-1918 to Nov-1921 Dec-1923 to Jun-1925 Sep-1925 to Aug-1927 May-1928 to Apr-1930 Oct-1930 to Nov-1936 Dec-1936 to Dec-1946 Nov-1955 to Feb-1958 May-1962 - Returned to Gembrook line Oct - 1977 - Transferred to ETRB ownership Steam Locomotive with wrought iron frame with cast iron cylinders7Apuffing billy, 7a, victorian railways, narrow gauge, steam locomotive

14A Built in 1914 and painted Canadian red & dark brown, this locomotive was issued to the Colac to Crowes line and saw service on all four lines, but mostly on the Colac to Crowes line. It was withdrawn from service in 1962 at Colac and sent to Newport Workshops for storage where it remained, except for a brief time at Bendigo North Work-shops in 1963. After overhaul, it was brought to Belgrave in 1965 where it has seen almost continuous service since. In 1978, it became the first of the preserved NA’s to trial a historic colour scheme for which the Canadian red & dark brown was chosen, but ended up mistakenly being painted a “London Tan” & dark brown. In 1996 it received a more correct Canadian red livery. This “temporary” trial livery has now given way to 14A’s designated livery of all-over black. Its physical configuration will match the late 1940s era with the extended bunker, guard irons, etc. Loco: 14A In service Thursday, 25th June 1914 Withdrawn April 1962 Livery Canadian red & dark brown Owner Puffing Billy Gauge 762mm / 2' 6" Status Preserved - Operational - Converted to running on Light Oil in 2018 Service History: Jun 1914 - Colac - initial allocation of a new locomotive Jun 1914 - May 1921 Colac Aug 1921 - UFTG. Sep 1921 - Feb 1923 Moe May 1923 - Apr 1927 Colac Jul 1927 - Apr 1929 UFTG. Apr 1929 - May 1932 Other May 1932 - Nov 1934 Moe Dec 1934 - Jan 1940 Wangaratta Jun 1940 - Workshops Oct 1940 - Mar 1947 Colac May 1948 - Nov 1960 Colac - Stored Apr 1962 - Jul 1962 Workshops - Stored Dec 1965 - Belgrave - In active service at Puffing Billy Railway Belgrave Victorian Railways - Narrow Gauge NA class steam locomotive number 14A Dates that 14A worked on the Gembrook Line Aug-1921 to Sep-1921 Jul-1927 to Apr-1929 Dec-1965 - Returned to service Oct-1977 - Transferred to ETRB ownership Steam Locomotive with wrought iron frame with cast iron cylinders - Converted to running on Light Oil in 201814Apuffing billy, 14a, victorian railways, narrow gauge, steam locomotive

6 NC Brake Van (4 ton capacity) Service History Purchased by the Puffing Billy Preservation Society (Body & underframe only): NC 6 Brake Van (4 ton capacity) - Awaiting restoration *NC 6.VA - 17/12/1919 NWS Built new - /11/1928 - Modified AC Malco BO 5/10/1934 NWS Into Workshops - 9/10/1934 NWS Out of Workshops (5 days) 17/ 3/1955 - Scrapped Historic - Victorian Railways - narrow gauge rolling stock - NC Class Full Guard's Van 6 NCTimber Guards Van wrought iron framepuffing billy, nc van, narrow gauge, victorian railways, 6nc, guards van, narrow gauge rolling stock

Photo shows a tramcar maintainer or pitman inspecting the underside of a bogie tram at Elwood Depot using an electrical lead lamp.Yields information about the maintenance and inspection of tramcars.Photograph from the Victorian Railways Magazine June 1930 showing a Tramcar maintainer.In ink of rear of prints "Photo Victorian Railways"tramways, trams, st kilda brighton electric tramway, vr trams, victorian railways, tramcar maintenance staff, elwood tram depot, pitman

Three similar photos used in the VR magazine, but this one has a different outlook or view from the others. In the magazine, each photo location was given. See item 611. Yields information about the VR trams and their routes.Photograph from the Victorian Railways Magazine June 1930 showing a hand at tram controller.In ink of rear of prints "Photo Victorian Railways"tramways, trams, st kilda brighton electric tramway, vr trams, victorian railways, drivers

It was constructed on a former Victorian Railways NKS type underframe and powered by a single cylinder, 500 cc B.S.A. side valve motorcycle engine to drive axle by roller chains through an 'Ariel Square Four' gearbox and has traveled on all four 2'6" narrow gauge lines that operated in the state of Victoria.Historic - Narrow Gauge Railway - Track Patrol Vehicle used by Puffing Billy Preservation Society and made from parts of a Victorian Railways track patrol vehicleMotorised small rectangular trolly made of wood and wrought iron ME1 P.B.P.S Track Construction Departmentme 1, trolley, victorian railway, 2'6" gauge, puffing billy, trolly

Model of Victorian Railways Broad Gauge - Dalhouse Station The Models were hand made including electric motors and cast metal by Desmond Henry Ramsay over 40 years - from the age of 15 ( 1930 ) until his death in 1970. The locomotives and carriages are all replicas of Victorian Railways Broad Gauge. The Dalhouse Station and station yard were inspired by victorian railways design. This Model of Victorian Railways Broad Gauge was kindly donated to the Puffing Billy Railway Museum by the family of Desmond Henry Ramsay - Elwyn Stankiewicz - Vanessa Bourke - Roger Ward. (plaque afixed on case)Historic - Hand made Model of Victorian Railways Broad Gauge by Desmond Henry RamsayModels of Victorian Railways Broad Gauge rolling stock - Hand Made - plastic and cast metal puffing billy, victorian railways, model railway, o scale, desmond henry ramsay

Typed letter in response to advice from the Ballarat School of Mines that trained female telegraphers were ready for employment. Victoria Railways were not interested in employing girls. telegraphy, victoria railway, women students, female telegraphers, e.b. jones, victorian railways

8A Built in 1908 and painted Canadian red & dark brown, this locomotive was issued to the Upper Ferntree Gully to Gembrook line. Over the years, it saw service on the Colac to Crowes and Moe to Walhalla lines, but it saw more service on the Gembrook line than any other. It was withdrawn from service in 1955 at Upper Fern Tree Gully and sold to the Beaumaris City Council where it remained on static display until 1970. After storage at Newport & Ballarat North Workshops, it was brought to Belgrave in 1976 for restoration. It was returned to service in 1982 after a complete rebuild in close to its late 1920s condition with its extended bunker & modified front end including the tapered “stovepipe” smokestack, steel cow-catcher and the all-over Black livery. Loco: 8A In service Monday, 2nd March 1908 Livery Canadian red & dark brown Owner Puffing Billy Gauge 762mm / 2' 6" Status Preserved - Operational Service History : May 1908 - UFTG. - initial allocation of a new locomotive May 1908 - Mar 1910 UFTG. Apr 1910 - Mar 1915 Colac Jun 1915 -Sep 1926 UFTG. Jan 1927 - Jan 1930 Moe Mar 1930 - Oct 1936 UFTG. Nov 1936 - Dec 1936 Moe Jan 1937 - Oct 1954 UFTG. Dec 1954 - Workshops Jan 1955 - Jan 1968 Other Jul 1970 - Apr 1977 Workshops Jul 1982 - Belgrave - In active service at Puffing Billy Railway Belgrave Victorian Railways - Narrow Gauge NA class steam locomotive number 8A Dates that 8A worked on the Gembrook Line Mar-1908 to Apr-1910 - initial allocation of a new locomotive Jun-1915 to Jan-1927 Mar-1930 to Nov-1936 Jan-1937 to Dec-1954 Jul-1982 - Returned to service PBRSteam Locomotive 8Apuffing billy, 8a, victorian railways, narrow gauge, steam locomotive

Ill, p.17.non-fictionA summary of the improvements made under Operation Phoenix"", the post war rehabilitation of the Victorian Railwaysoperation phoenix, victorian railways - publicity

The Victorian Railways guard's hat would have been part of a uniform guards were required to wear as on-board train staff.The Victorian Railways guard's hat has local significance as it was donated by a Wodonga resident. It also has historic significance due to its relative rarity and representativeness as part of the uniform worn by Victorian Railways staff, as well as its relatively good condition. Dark blue/grey felt Victorian Railways hat with the word 'GUARD' in gold on the front of a faded brown band. The hat has the VR logo and size on the inner sweat band. "Superior /Quality /Fur Felt / VR 7 1/4" in gold letters on one side of the inner leather sweat band.victorian railways hat, victorian railways guard's hat, v.r., victorian railways uniforms, railways uniforms, railways guard's hat

The Victorian Railways jacket would have been part of a uniform for railways employees. The Victorian Railways jacket has local significance as it was donated by a Wodonga resident. It also has historic significance due to its relative rarity and representativeness as part of the uniform worn by Victorian Railways staff. Blue/grey Victorian Railways jacket with "V.R." in gold letters on a dark blue rectangular background, stitched to each lapel and a lighter blue trim on the lower part of each sleeve."V.R." logo on each lapel.victorian railways, v.r., vr, victorian railways jackets

The blue work coveralls would have been worn as protective clothing for Victorian Railways employees working on train maintenance and workshop tasks in the later part of the 20th century. The style of the exterior pockets on the front suggests a date of c. 1970s-1980s.The Victorian Railways coveralls have local significant as part of the Wodonga Historical Society's donations from Wodonga residents. They also have significance from a social history perspective due to the VR logo on the front and the relative rarity of protective work clothing for Victorian Railways employees.Blue Victorian Railways work coveralls, with the VR logo above the proper left pocket on the front. The blue fabric is worn and stained from use."VR" logo above the proper left pocket on the front of the coveralls. "JONES / workwear / SIZE 87 R - 5" on the side of the proper left pocket on the front of the coveralls.victorian railways, v.r., victorian railways coveralls, victorian railways prtective work clothing