This glass milk bottle was manufactured and used mid to late 1900's (1834 Victorian dairy industry was founded) until the time that a cheaper container was invented(plastic bottles and polyethylene plastic lined cardboard cartons). In 1909 the supply of pure bottled milk was required for babies to overcome infant mortality due to unhygienic milk sources (unclean containers and unpasteurized milk). Due to the volume of milk being processed and hand milking could not keep up with demand, dairy farms introduced milking machines in the late 1930's. The great increases in dairy herds from the average of 18 cows per heard in 1950's to 142 cows per herd in 1996 required milk tankers to pick up the regions milk supply. This bottle was so constructed to be easily moved within the milk processing plants from the delivery vats/holding tanks to the final corking/sealing of the bottles for eventual distribution. From 1958 the milk bottle slowly became phased out of production. At this point in time Melbourne was drawing 160,000 bottles per week from the two major glass bottle works companies, e.g. Melbourne Glass Bottle Works Co.Victoria was the major state supplier of cows milk in the history of Australian milk production from the early 1800's. The Kiewa Valley and its region was a major contributor to meet that demand. Each bottle was "branded" during manufacturing to show the contents (pasteurized milk) and where it originated from (region and supplier). This method of recycling the bottles back to specific dairy farms was a good control method but an uneconomical "on cost" which was replaced by the "throw away" less costly plastic and cardboard containers. Kiewa Valley dairy herds had marked bottles bearing "90/9", "6/18", "6/33", "6/35" and "6/36" Found under house at 1 Beauty Ave., Mt Beauty.This heavy gauged glass milk bottle has a rim and a distinctive head at the top. This head has been manufactured to facilitate the movement of the bottle along the milk production line. The method of pouring milk into the bottle has been part of the "production line". This bottle has a one pint capacity and is made from "light green" coloured glass(a protection against light penetration). There are other milk bottles that do not have a "green" tint in them. This thick glass bottle to contain milk required its thickness because of the extensive handling before final consumption. Milk was delivered by the "milk man" direct to the homes of consumers. During this period delivery to homes in cities and towns was made initially by horse and cart and later by truck.On the bottom end of this bottle a circle within it "6/36" and next to this "MILK" and opposite "ONE PINT". Below this "THIS BOTTLE BELONGS TO MILK BOTTLE RECOVERY LTD" and below this "AND CANNOT BE USED WITHOUT WRITTEN PERMISSION" on the base "M" underneath this "15" glass bottles, commercial milk containers, domestic milk bottles, pasteurized milk bottles

This glass milk bottle was manufactured and used mid to late1900's (1834 Victorian dairy industry was founded) up until the time that a cheaper container was invented(plastic bottles and polyethylene plastic lined cardboard cartons). In 1909 the supply of pure bottled milk was required for babies to overcome infant mortality due to unhygienic milk sources (unclean containers and unpasteurized milk). Due to the volume of milk being processed and hand milking could not keep up with demand, dairy farms introduced milking machines in the late 1930's. The great increases in dairy herds from the average of 18 cows per heard in 1950's to 142 cows per herd in 1996 required milk tankers to pick up the regions milk supply. This bottle was so constructed to be easily moved within the milk processing plants from the delivery vats/holding tanks to the final corking/sealing of the bottles for eventual distribution. From 1958 the milk bottle slowly became phased out of production. At this point in time Melbourne was drawing 160,000 bottles per week from the two major glass bottle works companies, e.g. Melbourne Glass Bottle Works Co.Victoria was the major state supplier of cows milk in the history of Australian milk production from the early 1800's. The Kiewa Valley and its region was a major contributor to meet that demand. Each bottle was "branded" during manufacturing to show the contents (pasteurized milk) and where it originated from (region and supplier). This method of recycling the bottles back to specific dairy farms was a good control method but an uneconomical "on cost" which was replaced by the "throw away" less costly plastic and cardboard containers. Kiewa Valley dairy herds had marked bottles bearing "90/9", "6/18", "6/33", "6/35" and "6/36" Found under the house at 1 Beauty Ave., Mt BeautyThis heavy gauged glass milk bottle has a rim and a distinctive head at the top. This head has been manufactured to facilitate the movement of the bottled along the milk production line. The method of pouring milk into the bottle has been part of the "production line". This bottle has a one pint capacity and is made from "light green" coloured glass(a protection against light penetration). There are other milk bottles that do not have a "green" tint in them. This thick glass bottle to contain milk required its thickness because of the extensive handling before final consumption. Milk was delivered by the "milk man" direct to the homes of consumers. During this period delivery to homes in cities and towns was made initially by horse and cart and later by truck.On the bottom end of this bottle a circle within it "6/18" and next to this "MILK" and opposite "ONE PINT". Below this "THIS BOTTLE BELONGS TO MILK BOTTLE RECOVERY LTD" and below this "AND CANNOT BE USED WITHOUT WRITTEN PERMISSION" on the base "M" underneath this "4"glass bottles, commercial milk containers, domestic milk bottles, pasteurized milk bottles

This glass milk bottle was manufactured and used mid to late 1900's (1834 Victorian dairy industry was founded), until the time that cheaper containers were invented(plastic bottles and polyethylene plastic lined cardboard cartons). In 1909 the supply of pure bottled milk was required for babies to overcome infant mortality due to unhygienic milk sources (unclean containers and unpasteurized milk). Due to the volume of milk being processed and hand milking could not keep up with demand, dairy farms introduced milking machines in the late 1930's. The great increases in dairy herds from the average of 18 cows per heard in 1950's to 142 cows per herd in 1996 required milk tankers to pick up the regions milk supply. This bottle was so constructed to be easily moved within the milk processing plants from the delivery vats/holding tanks to the final corking/sealing of the bottles for eventual distribution. From 1958 the milk bottle slowly became phased out of production. At this point in time Melbourne was drawing 160,000 bottles per week from the two major glass bottle works companies, e.g. Melbourne Glass Bottle Works Co.Victoria was the major state supplier of cows milk in the history of Australian milk production from the early 1800's. The Kiewa Valley and its region was a major contributor to meet that demand. Each bottle was "branded" during manufacturing to show the contents (pasteurized milk) and where it originated from (region and supplier). This method of recycling the bottles back to specific dairy farms was a good control method but an uneconomical "on cost" which was replaced by the "throw away" less costly plastic and cardboard containers. Kiewa Valley dairy herds had marked bottles bearing "90/9", "6/18", "6/33", "6/35" and "6/36" Found under the house at 1 Beauty Ave., Mt BeautyThis heavy gauged glass milk bottle has a rim and a distinctive head at the top. This head has been manufactured to facilitate the movement of the bottled along the milk production line. The method of pouring milk into the bottle has been part of the "production line". This bottle has a one pint capacity and is made from "light green" coloured glass(a protection against light penetration). There are other milk bottles that do not have a "green" tint in them. This thick glass bottle, to contain milk, required its thickness because of the extensive handling (man and machine) before final consumption. Milk was delivered by the "milk man" direct to the homes of consumers. During this period delivery to homes in cities and towns was made initially by horse and cart and later by truck.On the bottom end of this bottle is a circle within it "6/35" and next to this "MILK" and opposite "ONE PINT". Below this "THIS BOTTLE BELONGS TO MILK BOTTLE RECOVERY LTD" and below this "AND CANNOT BE USED WITHOUT WRITTEN PERMISSION" on the base "M" underneath this "20"milk, dairy, glass bottle

This glass milk bottle was manufactured and used mid to late 1900's (1834 Victorian dairy industry was founded) up until the time that a cheaper container was invented(plastic bottles and polyethylene plastic lined cardboard cartons). In 1909 the supply of pure bottled milk was required for babies to overcome infant mortality due to unhygienic milk sources (unclean containers and unpasteurized milk). Due to the volume of milk being processed and hand milking could not keep up with demand, dairy farms introduced milking machines in the late 1930's. The great increases in dairy herds from the average of 18 cows per heard in 1950's to 142 cows per herd in 1996 required milk tankers to pick up the regions milk supply. This bottle was so constructed to be easily moved within the milk processing plants from the delivery vats/holding tanks to the final corking/sealing of the bottles for eventual distribution. From 1958 the milk bottle slowly became phased out of production. At this point in time Melbourne was drawing 160,000 bottles per week from the two major glass bottle works companies, e.g. Melbourne Glass Bottle Works Co.Victoria was the major state supplier of cows milk in the history of Australian milk production from the early 1800's. The Kiewa Valley and its region was a major contributor to meet that demand. Each bottle was "branded" during manufacturing to show the contents (pasteurized milk) and where it originated from (region and supplier). This method of recycling the bottles back to specific dairy farms was a good control method but an uneconomical "on cost" which was replaced by the "throw away" less costly plastic and cardboard containers. Kiewa Valley dairy herds had marked bottles bearing "90/9", "6/18", "6/33", "6/35" and "6/36" Found under the house at 1 Beauty Ave., Mt BeautyThis heavy gauged glass milk bottle has a rim and a distinctive head at the top. This head has been manufactured to facilitate the movement of the bottle along the milk production line. The method of pouring milk into the bottle has been part of the "production line". This bottle has a half pint capacity and is made from "clear" glass. There are other milk bottles that have a "green" tint in them and this tint was to protect the contents from sun damage. This thick glass bottle to contain milk required its thickness because of the extensive handling before final consumption. Milk was delivered by the "milk man" direct to the homes of consumers. During this period delivery to homes in cities and towns was made initially by horse and cart and later by truck.On the top half of this bottle is "MILK" and opposite "HALF PINT". Below this "THIS BOTTLE BELONGS TO MILK BOTTLE RECOVERY LTD" and below this "AND CANNOT BE USED WITHOUT WRITTEN PERMISSION" on the base is "2 M" underneath this "8/11" and underneath is "ISM -169"glass bottles, commercial milk containers, domestic milk bottles, pasteurized milk bottles

This glass milk bottle was manufactured and used mid to late 1900's (1834 Victorian dairy industry was founded) up to the time that a cheaper container was invented(plastic bottles and polyethylene plastic lined cardboard cartons) and produced. In 1909 the supply of pure bottled milk was required for babies to overcome infant mortality due to unhygienic milk sources (unclean containers and unpasteurized milk). Due to the volume of milk being processed and hand milking could not keep up with demand, dairy farms introduced milking machines in the late 1930's. The great increases in dairy herds from the average of 18 cows per heard in 1950's to 142 cows per herd in 1996 required milk tankers to pick up the regions milk supply. This bottle was so constructed to be easily moved within the milk processing plants from the delivery vats/holding tanks to the final corking/sealing of the bottles for eventual distribution. From 1958 the milk bottle slowly became phased out of production. At this point in time Melbourne was drawing 160,000 bottles per week from the two major glass bottle works companies, e.g. Melbourne Glass Bottle Works Co. Victoria was the major state supplier of cows milk in the history of Australian milk production from the early 1800's. The Kiewa Valley and its region was a major contributor to meet that demand. Each bottle was "branded" during manufacturing to show the contents (pasteurized milk) and where it originated from (region and supplier). This method of recycling the bottles back to specific dairy farms was a good control method but an uneconomical "on cost" which was replaced by the "throw away" less costly plastic and cardboard containers. Kiewa Valley dairy herds had marked bottles bearing "90/9", "6/18", "6/33", "6/35" and "6/36" This particular one has "7/14".This heavy gauged glass milk bottle has a rim and a distinctive head at the top. This head has been manufactured to facilitate the movement of the bottled along the milk production line. The method of pouring milk into the bottle has been part of the "production line". This bottle has a one Imperial pint capacity and is made from "clear" glass. There are other milk bottles that have a "green" tint in them. Around the bottom side of the bottle and blown into the glass "ONE IMPERIAL PINT". Below these markings and stenciled is "KIEWA" (in freehand style and underlined) underneath is "PASTEURISED FULL CREAM MILK" underneath this ,in freehand stiyle is "USE" next to this in block style "KIEWA BUTTER, CREAM, AND ICE CREAM MIX" to the left of this ,and barely readable is stenciled "THIS BOTTLE ALWAYS REMAINS/ THE PROPERTY OF/ NORTH EASTERN DAIRY Co. Ltd". On the base of the bottle is molded a big "2". with a smaller "m". An identification mark of "7" over "14" is within a circled boundary. Below this is moulded "RM - 15". glass bottles, commercial milk containers, domestic milk bottles, pasteurized milk bottles

This commemorative badge identifying the wearer as a Girl Guide and was used in the 1970's and later. The Girl Guides "World Camps" was founded in 1924 and each subsequent "camp" was in other global countries. The Camp Baree was held in 1947/1948 in Pennsylvania in the USA. In Victoria, Australia, a Barree Regional location for Girl guides, encompasses the Kiewa Valley and its regions. Girl guides in rural areas covered the same developmental programs as in the city areas but the bush settings of annual camps did not have the same impact as for city based guides. The comradeship however, bringing together girls from a widely diverse background, was still a very important objective of the Girl Guide movementThe significance of this badge is that the Girl Guides held a World Camp in the Barree region which included the Kiewa Valley.This world wide attention(Girl Guides) to this region paid special attention to the "home side" girls and highlighted in particular those girls in the Kiewa Valley who participated in the Girl Guide movement. The ability to have such a personal contact with so many girls from so many world regions helped to break the somewhat isolated regional life. The fundamental lessons of the girl guides was and still is to enrich young girls knowledge of skills which provides self esteem, pride in achievements and the togetherness with like minded girls. Social barriers are left behind and good friendships are formed. Some of these friendships continued as life long links.This round badge made from brass and has coloured enamel sections outlining various "Barree Region" scenery. In the far distant horizon are snow capped mountains. These are coloured brown with white tipped summits.The central focus is a blue stream with a dark blue "gum" tree to the left and a brass etched tent pegged onto green grass. These pictures are framed within a house structure. A red coloured boomerang lies under the "house" frame with the name of the region on it,"BARREE REGION" The badge is fastened onto a lapel or other clothing by two "L" shaped hooks extending from the back of the badge.On the front of the badge (on the sketched boomerang "BARREE REGION". On the back in raised lettering is"BERTRAM BROS MELB."societies, girl guides, barree region, metal identity badges

This text-book is divided into three parts: I. The Right-Angled Triangle; II. The General Triangle and Mensuration; III. The General Angle and Compound Angles. This corresponds to the Matriculation and School Certificate stage.This text-book is significant as it was the book used by Mount Beauty High School students in the mid 1900's. It is also significant as it was used by I.Davies a member of a local family. And it also has good interpretive capacity.Red cover, black lettering, embossed around a triangle, CAMBRIDGE MATHEMATICAL SERIES, with trademark in centre of triangle.Pencilled name inside front cover looks like I.Davies.book, maths, trigonometry, mount-beauty-high-school, school, students, elementary, c.v.-durell, r.m.-wright

This clear, light green, glass "hand blown" fruit preservation jar was used before the mass manufacturing of "screw topped" fruit preservation glass jars imported from Asia or great Britain. The "Mason's Patent" on the jar was for the screw-neck form of the jar top. The screw neck provided the jar with a vacuum seal (preservation) method of fruit jar storage. The reference on the jar of the actual date that the patent was established was in effect for 13 years with extension of a further 7 years. It was an American world wide patent which resulted in only specific manufacture to Glass Works that had paid the manufacturing levy imposed. The air bubbles in the glass suggests that this jar was "hand blown". This would then place the manufacture date before 1900. Preserves came in glass jars bought at the local grocery store or at a large city store on a shopping expedition. The shape of the jar changed as did the stopper used to seal it. Jars were recycled remaining the property of the manufacturer. History of Mason's.This fruit jar is significant to a rural area such as the Kiewa Valley and in the early 1900's when the preservation of fruit and vegetables was an intrinsic part of the typical rural farm/property family. Local shops could only supply fruit and vegetables as seasons permitted. The travelling "green grocer" was more prevalent in towns and cities but not in semi remote rural areas. Historical: Change of jars - shape, glass, stopper, embossing & use. Aesthetic: Display showing embossing & shape especially if in good condition.This vintage "Mason's Patent", screw on thread lid fruit jar was hand blown (air bubbles). It was produced for the home canning of local fruit. The jar is made from thick glass and is tinted light green. Clear glass jar with slight green tinge used for preserves. sides almost straight but jar has a slight bulge almost all the way to the top. Heavily embossed on 1 side. Horizontal print in large capital letters. At the top - manufacturer's name with emblem beneath it. The base has a slight bulge inwards with embossing.In a half ecliptical form "MASON'S" and underneath the Mason's logo.Under the logo "PATENT/ NOV 30 th / 1858". On the base "C201" (double molded).fruit and vegetable preserves, domestic fruit and vegetables bottling, off seasonal fruit and vegetable storage, jar, bottle, preserves, mason's preserves

Bushells tea and coffee producers started in Brisbane(1883) and expanded to Sydney, Melbourne(1899), Fremantle and finally to Auckland(1937). Like other Pacific Island sourced condiments Tea and coffee were a lot easier to import than British or European goods. Local Australian industries were starting to develop and grow to overcome the long transportation times and the high costs of goods from traditional suppliers. Bushells Pty Ltd is a prime example.This "Bushells" Coffee tin is a good example of Australian "grown" condiment suppliers serving the "whole" of the Australian marketplace. Rural areas were not neglected and the purchase price for goods were a reasonable levels. Kiewa Valley experienced a population growth from the late 1940's and due to the migrant works in the Kiewa Hydro Scheme the greater use of coffee was initiated. Rural areas, on the whole, where the population was more connected to some degree with a British heritage lineage were predominately tea drinkers. The American film productions, however, screened in Australia post 1950's showing a greater degree of coffee drinking "stars" had a long term effect upon the drinking habits of the rural populous. This round tin of coffee with lid is made from pressed steel lid framed top and bottom. Sturdy cylindrical body is made of cardboard. Paper information label is pasted onto the container with promotional and logo information.In large print and on opposite sides are two manufacturers labels.The topprint and on a diagonal slant in gold letters on a dark blue background is "BUSHELLS" underneath this "PURE" and below this on a red background "COFFEE". On one side in smaller print "EASY TO MAKE" and below this "Use one dessert-spoonful for each cup of coffee desired. Place in the pot and pour over it fresh water briskly boiling. Let stand for five minutes, then strain". Below this "1 IB. net" and underneath is a signature "BUSHELLS" below this in small print "Pty. Ltd." Below this, in a vertical row are"SYDNEY MELBOURNE fREMANTLE AUCKLAND"coffee and tea processors and distributors, hot drink suppliers

This "ladies" pocket knife was used up to the late 1900's by influential and "well off" ladies, not only as a fashion statement but as a practical tool when away from the kitchen/home to peel fruit and provide a cutting instrument for small items. It was a method to show the growing independence of women to skillfully process food away from the home and kitchen. The use of such a small compact knife could also have been used by male cigar smokers (docking the end of the cigar)This "lady's "purse" knife was a demonstration of the growing independence of women in Australia and especially in rural areas up to the 1940's. The two World Wars provided the opportunity for women to take over what was traditionally "men's work". This evolution of women's equality in society brought changes to what the traditional role of rural women had been entrenched from first colonisation of Australia. The use of such a small compact knife could also have been used by male cigar smokers (docking the end of the cigar). This method of preparation of a good cigar would have been used by wealthy property owners or men of "class"This small one blade knife (lady's) has an "ivory" body containing one small blade. Horizontal lines in "off white" appearance run from one end to the other. One end has a "U" fitting(to provide an anchorage for a chain). This small knife could also have been used by male cigar smokers.ladies pocket knife, small knives, traveller's cutting implements

This photograph was typical of the mid 1900's when photography was in the hands of the professional artist for important events, be they family or public occasions. This photograph holds and protects from ageing, part of a very significant occasion, the 90th birthday photograph of the matriarch Claire Roper, one of the founding grazier families from Tawonga within the Kiewa Valley This photograph therefore hold a very historical significance and has good exhibition value. This black and white photograph was professionally taken on Kodak paper in the time of the Australian Melbourne Olympics 1956. See KVHS 0092 for frame.On back of photograph "KODAK official sponsor of the Olympic Games" Underneath the symbolic rings of the Olympic Federationphotograph of early 1900's kiewa valley pioneer, the roper family, claire roper, pioneer family, cattle, bogong high plains

This "first reader" for children in a Victorian Primary school was fashioned by the period that it was printed in (1951), and the associated educational principles was applied by the Victorian Educators. It defines the role play of young children, at this point, in their educational development and contained within the(1950's) "society's" mores and expectations. This book was widely used by state schools in Victoria including Mt Beauty and Tawonga Primary Schools.This reader is significant to the Kiewa Valley because it demonstrates that there was still a very marked "one book" fits all school environmental approach by State educators which the local schools were apart of. This book is one of the KVHS children's school book collection, which many were donated by local families whose children went to Mt Beauty Primary School. Therefore this reader represents a social history significance for the period from 1950's and 60's. The book is in good condition, consequently making it suitable for exhibitions, and highlighting schools in the Kiewa Valley along with what local children read in these schools. This primary school reader has an orange cover with "John and Betty" printed in green. Below this is the green outline of a young boy leading his dog(Scottish Terrier) on a lead. Behind him is the red outline of a young girl (bow tied waist belt) in front of a cat(tail up). A thick green line is situated below the figures. The cover is 180 gsm thick. Inside the book are colored sketches of a boy and a girl playing well defined "boy" and "girl" activities (gender specific for the period of print 1951) Below these activities are simple descriptive words for the above activities.On the front page "John and Betty" below this "The earliest Reader for the Little Ones". Below this "Illustrations by Marjorie Howden" Further down the page and in smaller print is "Education Department of Victoria 1951". Below this and under a fine line "A.C. Brookes, Government Printer, Melbourne"first grader reader, primary education 1950's style

This manual telephone exchange console is an important piece of equipment which provided the most efficient method of long distance communications in the 1950's to the 1980's. Communications were critical, not only for the regional Hospital, but also for large construction sites i.e. the Kiewa Hydro Scheme, especially if they are in dense rugged mountainous regions. The degree of Occupation Health and Welfare on industrial sites were at a bare minimum compared to the work scene after the 1980's.This telephone exchange console is highly significant to both the Kiewa Valley and Mount Beauty region because it was so important in the communications field relating to operational safety and work related controls. The success of any large undertaken relies heavily upon good communications. In the hospital this method of communications is still used i.e. patient to ward station. This flag system link a patient's room to the controlling nursing station. Identification of the patient needing help is crucial for swift action from the available medical staff. Similarly in large construction sites such as the Kiewa Hydro Scheme, successful instant communications was also essential. This switchboard required a 50 volt supply to successfully operate and was in use when both telecommunications and postal were under the one Federal Government carrier i.e. The Post Master General. A benefit with a line communication system (such as the one that fed this console was that interference from atmospheric conditions did not impede the connection.This console telephone switchboard (manual) unit has a shutter operation (precursor to the light indicator) to identify the caller to the telephone switchboard operator. This switchboard has a ten point indication shutter system allowing the operator to clearly identify where the caller is located. The console has a 44 connection point holes with their configurations in a triangular shape. The shutters are held closed by a small lever at the top which is opened by a small electrical charge from the incoming call. The operator uses a wind up handle to power a magneto connector(handle on the console's right side). The telephone hand set is located on the left side of the console. sec vic kiewa hydro scheme, alternate energy supplies, alpine population growth and communications

This pair of "adjustable" boots came from the 1950's era in which the majority of footwear was either locally manufactured or imported from England or Europe. Quality hard wearing leather was a rural necessity especially for the cattle mustering activity in the Kiewa Valley and the Bogong High Plains region. The late 1900's provided a cheaper made riding boot from Asia, however many rural based riders still prefer an Australian made boot. The better quality (stronger stitching) of Australian boots is the main considerations of "stock horse riders". In 1947 a scientific research project started to provide an impact analysis of any damage to alpine vegetation by cattle grazing in the Alpine regions incorporating the Bogong High Plains area. This monitoring is the longest running ecological study ever undertaken in Australia. From this study, compelling evidence was presented to the Victorian Government to cease cattle grazing in the Alpine regions including the Bogong High Plains. All grazing was banned by the Victorian Government in 2005. Recreational horse riding within the Bogong High Plains is still permitted.These pair of women's riding boots are very significant to the Kiewa Valley as the boots were worn by one of the descendants of a pioneer family living and operating a cattle station before the SEC Hydro Electricity Scheme opened up the semi remote rural location in the 1950's. These boots were worn during the annual six weeks (approx.) mustering of cattle in the Bogong High Plains location (Victorian Alps region). The owner of these boots was Clare Roper, part of the Roper Family who built a "lodging" hut on the "High Plains" for accommodating riders during the periods (up to six weeks) when controlling grazing cattle during the summer muster seasons. It was unusual for women in the early to mid 1900's to go up on the High Plains to join the muster, which Clare Roper often did. These boots have high historical significance and good interpretive capacity.These brown "knee high" lady riding boots, are fastened by long "boot" laces which go from the base of the "fastening" position to a boot height of 22 cm. At the top end of the boot is a leather flap which crosses the front section of the boot and is fastened to the outside leg region by two straps. These provide the wearer with an adjustable tie. The boot has a "tongue" of 22 mm long. The boot has six pairs of metal boot lace "hooks" and eight pairs of boot lace "eyelets".ladies riding boots. cattle mustering footwear. rural footwear. cattlemen. bogong high plains. roper family. horses.

This stock horse saddle was probably used in the mid 1900's. This was the period when cattle mustering was at its prime. The movement of cattle was by mounted stock horse only and not by other methods. Northern territory cattle stations in the late 1900's started to use helicopters for "cattle control". In the KIEWA Valley/Bogong High Plains and other rural cattle producing areas required well trained stock horses and stockmen for cattle control. It is only in the later 1900's that motor bikes and four wheeled quad-bikes have taken over, in part, from the mounted stockman.This horse saddle is very significant to the Kiewa Valley because of the early introduction of cattle stations in what initially was regarded as a semi remote location. The maintenance of cattle in the Kiewa Valley is and was an important requirement. A good stock horse saddle as and is important, especially during the period when cattle were grazed on the Bogong High Plains. The mustering and and moving cattle from the valley pastures to the high country was a demanding and dangerous exercise requiring "sure footed" stock horses.The "good" saddle was a vital part of this cattle mustering. A scientific study started in 1947 to study the impact of grazing cattle on the natural Alpine and sub Alpine vegetation found grazing cattle had an adverse affect on the natural Alpine and sub alpine vegetation, and grazing on the plains was stopped by the Victorian Government in 2005.This "camp draft" in the High Plains could take up to six weeks.This all leather "stock horse" saddle shows plenty of wear. It is in "full harness" configaration with stirrups and leg protectors horse, country, leather, gaiters, high, grazing, cattlemen, laces, studs

This type of cast iron kettle was used by pioneer families, mainly rural in the early 1900's upon open fires (log). It covered rural activities that needed a constant readily available source of boiling water, in or mainly outside the kitchen of homesteads. This kettle was used in the early to late 1900's for the refreshment of stock men and farmers that had irregular "tea" breaks under sometimes hard and gruelling conditions.This kettle belonged to and was used by a Kiewa Valley, pioneer family, the Roper Family. This kettle was moved from their Kiewa Valley property to their hut built on the Bogong High Plains. The Bogong High Plains area provided Kiewa Valley cattlemen a good supply of fodder to supplement their Kiewa Valley grazing areas. This "camp draft" activity , in the high plains, could take up to six weeks.This large cast iron modified camp pot (cauldron) has a long tap connection located at the bottom end. The "tap" is made from brass and has a simple elongated "bar" control swivel at the end to control the water flow. The tap suggests that only water was heated (to a constant boil) for the replenishment of cattlemen's, or other horse rider's, tea or coffee mugs. Refreshments at a "temporary" location on the Bogong High Plains. There was a "log" hut built by the Roper family as temporary accommodation for cattlemen and other family members.Ot the flat bottom "FIRST QUALITY 2 GALLONS"camp fire cooking utensils, hot plate, cast iron cooking appliance, drovers kitchen

This stock horse bridle was probably used in the mid 1900's. This was the period when cattle and sheep mustering was at its prime. The movement of cattle and sheep was by mounted stock horse only and not by other methods. Northern territory cattle stations in the late 1900's started to use helicopters for "cattle control". In the KIEWA Valley/Bogong High Plains and other rural cattle/sheep producing areas required well trained stock horses and stockmen for cattle/sheep control. It is only in the later 1900's that motor bikes and four wheeled quad-bikes have taken over, in part, from the mounted stockman.This horse bridle is very significant to the Kiewa Valley because of the early introduction of cattle and sheep stations in what initially was regarded as a semi remote valley location. The maintenance of cattle and sheep in the Kiewa Valley was, and still is an important requirement of livestock management. A good stock horse bridle is important, especially during the period when cattle and sheep were grazed on the Bogong High Plains. The mustering and and moving cattle/sheep from the valley pastures to the high country was a demanding and dangerous exercise requiring "sure footed" stock horses.The "good specialised" bridle was a vital part of this cattle/sheep mustering. A scientific study started in 1947 to study the impact of grazing cattle/sheep on the natural Alpine and sub Alpine vegetation found grazing cattle had an adverse affect on the natural Alpine and sub alpine vegetation, and grazing on the plains was stopped by the Victorian Government in 2005.This "camp draft" on the Bogong High Plains could take up to six weeks.This harness bridle includes "blinders, winklers or blinkers" and would therefore be used on a pack or "working" horse. This bridle has rings on each end of the browband. The bridle is one used by a horse working in a team configuration pulling a heavy cart or wagon. The bridle has ten adjustable straps to allow it to accommodate a variety of horse sizes. See KVHS 0495 for a stock horse saddle.horse, country, leather bridle, gaiters, high country grazing, cattlemen, laces, studs

This Pie Iron was used in the mid to late 1900's when stock, both cattle and sheep, were grazed on the Bogong High Plains. Providing meals for stockmen over open fires, even in log cabins in the Victorian Alpine region, was usually by a "camp cook" or a stockman designated "cook" from the Valley station/property. The use of "camping cooking utensils were a necessity and not a "weekend" affair. Stockmen could spend up to six weeks on the plains and all their cooking needs required had to "pack horsed" from the valley below. A scientific study started in 1947, to study the impact of grazing cattle on the natural Alpine and sub Alpine vegetation found grazing cattle had an adverse affect on the natural Alpine and sub alpine vegetation, and grazing on the plains was stopped by the Victorian Government in 2005.This item is highly significant to the Kiewa Valley as it demonstrates the kind of cooking utensils that were required for camp drafts in the Bogong High Plains environment. As the control of cattle and sheep in the High Plains was very demanding upon horse and rider, good "tucker" was a pre- requisite for a successful operation. As the time spent in this remote location was governed by the climatic condition maximum utilisation of the very good pastures in the High Plains was crucial to a successful and profitable season.This pie iron has two pie forms in horizontal configuration and both top and base rounded forms are connected at one end (Top) with pop rivet application. This application allows for the "opening" up of the two halves. The bodies are made from cast iron in a "cup" form and a metal rod and wooden handle extend to permit the opening of the two sides. The inner side of the "cups" are smooth which relates to pie requirements and not the jaffle/sandwich irons. A clasp metal "D" ring is installed at the end of one wooden handle (to keep the iron in the close/cooking position).camp fire cooking utensils, hot plate, cast iron cooking appliances, pie irons, jaffle irons, drovers kitchen

This Cresolene vapouriser is an "American" product when "home" based remedial products were of a high demand due to lack of specialised medical facilities such as a hospital in rural communities. "An apparatus for reducing medicated liquids to a state of vapor suitable for inhalation or application to accessible mucous membrane A device for volatising liquid anesthetics." The only criteria used by Health authorities in the decision to provide a community with hospitals was and still is the size of the population it feeds. The introduction of the SEC Victorian Hydro Electricity Scheme started in the 1940's, was the impetus for health planners to build a hospital in the Kiewa Valley. Rural regions especially those considered semi or fully remote locations had to rely on farm based remedial health "alternative medical treatment". This product is such a remedy.This vapouriser is very significant to a rural area such as the Kiewa Valley as it demonstrates the "home" remedies that were available to rural communities such as the cattle and sheep stations before the Kiewa Valley had a hospital(1949). The influx of workers employed by the SEC Vic. Hydro Electricity Scheme(circa 1940's onward) changed dramatically the need for a hospital and specialised medical treatment. The reliance of "health products" such as this vaporiser were still in high demand especially when on the box of this product was printed "Guaranteed under the Food and Drugs Act, June 30, 1906, Serial no. 436". Also on the packaging is printed "A remedy Whooping Cough also Asthma, Catarrh, Colds Diptheria, Croup, Coughs Hay Fever, Sore Throat, Influenza, Etc." An additional benefit of this product "Is obnoxious to Moths, Flies, Mosquitos, Ants, Cock Roaches, Hen Lice, and other Troublesome insects." This advertising is dated before a tightening in the "advertising" legislation of post mid 1900's. However it was a good attraction for rural communities wanting relief of "rural" pests. This vaporiser stand with its cradle and dish is made from cast iron (stand) and tin (dish). At the bottom of the "dish" is a flame diffusion port with eight heat directional holes. The stand upright is painted gold in colour.See KVHS 0342 (B) for markings and advertising material printed on the box which contains this item.home based vaporisers, first aid, home nursing, over-the-counter medicines

This packaging/box containing a home based health product was in use well before the Federal Department of Health legislation tightened up the permissible advertising for "health" products. The strict Occupation and Health Legislation of the later 1900's would not have allowed the grandiose statements printed on this container. It was only later in the 1900's that stricter laws covering medical or quasi medical products came into Australian legislation.This box is very significant (in the time period of pre 1940's), to a semi isolated region as the Kiewa Valley, especially before the valley had a hospital, pre 1949. The reliance of "health products" such as what is stored in this box, were still in high demand, especially when on the box of this product was printed "Guaranteed under the Food and Drugs Act, June 30, 1906, Serial no. 436", a quasi legitimising statement. Also on the packaging is printed "A remedy Whooping Cough also Asthma, Catarrh, Colds Diptheria, Croup, Coughs Hay Fever, Sore Throat, Influenza, Etc." An additional benefit of this product "Is obnoxious to Moths, Flies, Mosquitos, Ants, Cock Roaches, Hen Lice, and other Troublesome insects." This advertising is dated before a tightening in the "advertising" legislation of post mid 1900's. However it was a good "purchase" for rural communities wanting relief of "rural" pests.home based vaporisers, first aid, home nursing, over-the-counter medicines

This linesman belt was used under the 1947 Electricity Regulations and before tighter Occupation and Health regulations (late 1990's early 2000's) were introduced that mechanical lifting platforms(wherever possible) replaced the belt up the pole method.The safety concern was that it required that tools needed by the linesman had to be placed in a large canvas bag and attached to the belt (extra weight) then the linesman had to climb the ladder. Ladders had to be at the correct angle and not able to "slip" from their initial footings. A full harness and a secondary fall belt is now mandatory for pole linesmen. The safety of fellow workers could be compromised if they were required to assist or recover the first linesman if needed. In 2006 an additional 269 registered lineworkers were employed. Please note that the terminology of linesman has become unisex. The linesman's belt enabled the linesman to place his feet against the pole adjust the belt (if needed) and lean back securely allowing both hands to be free to work with. This linesman belt is very significant to the Kiewa Valley due to the numerous poles and high voltage overhead power structures that needed maintenance for the extensive "mushroom" installation of electrical power polls(wood and metal). On high poles (steel) climbing pegs were welded on, however in the Alpine areas snow in winter caused an OH&S problem which were hard to overcome. The safety of a linesman when maintenance of electricity line on poles can be highlighted by the New Zealand linesman who survived an 11,000 volt shock when carrying out maintenance. For the record 11,000 volts is four times more powerful than execution by "the electric chair". The maintenance of the linesman's belt was his responsibility (keeping it clean and in "good" condition). Labour laws change this initial responsibility, from the linesman, to the employer. Climbing pegs were installed on higher poles that extended beyond the reach of ladders.This thick leather linesman belt is made from two lengths of heavy lengths of leather straps sewn together to make up 80% of the belt. The remaining 20% is "the belt tonge" which has eleven holes for three (solid steel tang) buckle connections.kiewa hydro electricity scheme, victorian state electricity commission, relays, generators, electrical pole maintenance

This bottle of castor oil was used during the mid to late 1900's when there was a Hospital in the Kiewa Valley, but regarded as only for serious injuries and near death situation. For this reason many households had a "first aid" box full of items such as this bottle of castor oil. Home based remedies for non life threatening injuries and illnesses were a part of life in a semi remote rural region. True and trusted family "health" remedies were passed from generation to generation.This Castor Oil bottle is very significant to the Kiewa Valley as it demonstrates the self reliance of the early farming and grazing pioneer families. Knowledge of "first aid" was uppermost to the survival of families before the late 1900's. Naturopathic remedies such as connected with the castor oil contained in this bottle, although may not be sanctioned by medical research, does not take into account of the positive "self healing" of the human mind (if you think it is doing you good it creates a positive action). Such preservation techniques were handed down through the generations.Medical Reference material was limited to books available and read and not not from "the internet" in the latter part of the 1900's. The availability of General Practitioners increased because of the boost in the population growth (SEC Vic Hydro Electricity Scheme) in the Kiewa Valley from 1940's onward. This small indigo coloured glass bottle has a narrow neck and a screw on lid.It has an embossed manufacturer's name and contents (Castor Oil) on one side and identification marks embossed on the underside base.medicine bottles, home first aid remedies, indigo glass medicine bottles

Soft drink came in bottles bought at the local grocery store or at a larger city store on a shopping expedition. The shape of the bottles changed as did the stopper used to seal it. Bottles were re cycled remaining the property of the manufacturer. The history of Zedmanfg Company, Albury. Historical: Change of bottles - shape, glass, stopper, embossing, use. Aesthetic: Display showing embossing & shape especially if in good condition. Clear glass bottle. Bottom half has straight sides. Upper half tapers to the top where a metal crimp fits over the lip. Manufacturer's name is heavily embossed in cursive script diagonally across the lower half. The place 'Albury' is embossed below the diagonal script, in capital letters.There is heavy embossing at the base and at the bottom of the sides. All in capital letters. It has a crown seal - AGMZedManfg Co. Albury - across the bottom half of the bottle. At the base on the sides around the circumference 'This bottle is the property of the Zedmanfg Co. Albury. On the Base: F1486, GM inside A, M 113 glass, bottle, domestic, household, albury, zedmanfg co., drinks, lemonade

Soft drink came in bottles bought at the local grocery store or at a large city store on a shopping expedition. The shape of the bottles changed as did the stopper used to seal it. Bottles were re-cycled remaining the property of the manufacturer. History of Cohn Bros., Bendigo & Swan Hill.Historical: Change of bottles - shape, glass, stopper, embossing, use. Aesthetic: Display showing embossing & shape especially if in good condition.Clear glass bottle. Bottom half has straight sides. The top half tapers to the top where a metal crimp fits over the lip. Manufacturer's name is embossed in print in block letters with its logo just above halfway from the bottom. At the base on the sides is embossing in capital letters around the circumference. The base is embossed with the crown seal of AGM.On 1 side half way up is embossed - Cohn / circle with CB inside around top of circle is Bendigo and around bottom of the circle is Swan Hill / Bros.is on the other side of the circle. - On the other side is embossed - The property of the Cohn Bros. Vic. Bry. Co. Ltd. Bendigo & Swan Hill. At the base - F1449 AGM (crown seal) M 2glass, bottle, domestic, household, drinks, lemonade, cohn bros., swan hill, bendigo

Soft drink came in bottles bought at the local grocery store or at a large city store on a shopping expedition. The shape of the bottles changed as did the stopper used to seal it. Bottles were re cycled remaining the property of the manufacturer. History of ECKS Ltd..Historical: Change of bottles - shape, glass, stopper, embossing, use. Aesthetic - Display showing embossing & shape especially if in good condition.Clear glass bottle with graphite stopper. Straight sides. Top third tapers sharply into a neck. One third from the top it is heavily embossed with the letters ECKS. It is heavily embossed, in capital letters, around the bottom of the sides and lightly embossed on the base and near the opening.Below the opening is embossed '28'. Side: 'ECKS'. Bottom of sides around circumference: 'The property of ECKS limited Melbourne and its use by others is illegal.' Base: 22bottle, lemonade, soft drink, ecks

Soft drink came in bottles bought at the local grocery store or at a large city store on a shopping expedition. The shape of the bottles changed as did the stopper used to seal it. Bottles were re cycled remaining the property of the manufacturer. History of R.J. Hadden's company in Benalla.Historical: Change of bottles - shape, glass, stopper. embossing, use. Aesthetic: Display showing embossing & shape especially if in good condition.Clear glass bottle heavily embossed. It was used for lemonade. It has straight sides that taper towards the opening two thirds of the way up. On 1 side the company's logo forms a circle with the word 'lemonade' embossed horizontally inside the circle. On the other side, at the base, are 2 lines of embossing.R. J. HADDEN - moon shape across the top forming the top of a circle with BENALLA completing the circle below. LEMONADE is embossed horizontally inside this circle. On the other side of the bottle: 'This bottle is the property / of R.J.Hadden, Benalla.' Base: lemonade, benalla, bottle, drink, r.j.hadden, soft drink

Soft drink came in bottles bought at the local grocery store or at a large city store on a shopping expedition. the shape of the bottles changed as did the stopper used to seal it. Bottles were re cycled remaining the property of the manufacturer. History of Murray Brewery, BeechworthHistorical. Change of bottles - shape, glass, stopper, embossing, use. Aesthetic. Display showing the embossing & shape especially if in good condition.Clear glass bottle. Embossed print in capital letters, around half of the circumference, one third of the way down from the top between the 2 longitudinal joins. The bottom half has straight sides and the top half tapers to the top where a metal crimp fits over the lip. Around the circumference is embossed print in capital letters. The base also has embossing. Crown Seal.Around circumference one third from top: 'Murray B.' Around circumference at base: ' Propetery of Murray Breweries pty Ltd. Beechworth.' Base: F1767 Symbol: 'AGM' and '445' 'M O'beer, drinks, lemonade, beechworth brewery, murray breweries, bottles

Soft drink came in bottles bought at the local grocery store or at a large city store on a shopping expedition. The shape of the bottles changed as did the stopper used to seal it. Bottles were re cycled remaining the property of the manufacturer. History of Marchants & Co. Ltd.Historical: Change of bottles - shape, glass, stopper, embossing, use. Aesthetic: Display showing embossing & shape especially if in good condition.Clear glass bottle with groove criss cross patterned sides near the base and three quarters of the way up where the bottle tapers to form straight sides half way to the opening. Between the criss cross patterns is white and red painted print and a 'ceramic label. The red plastic stopper is attached at the opening.On one side: Red and white "Serve Icy Cold / Marchants / It's the Most On the other side: A / Sparkling / Summer Drink / Bottled by Marchant & Co. Ltd / Melbourne. Please Return / stopper / with bottlemarchants, lemonade, soft drink, plastic screw, bottles, drinks

Beer came in bottles sold at licensed premises either locally or in larger cities visited during shopping expeditions.The shape of the bottles changed. The bottles were re cycled remaining the property of the manufacturer who paid for them. History of the Richmond Brewery, Richmond.Historical: Change of bottles - shape, glass, embossing. Collected by bottle collectors. Aesthetic: Display showing embossing & shape especially if in good condition.Clear glass bottle used for beer. Bottom half has straight sides. The top half tapers to the opening where a metal crimp fits. It has a crown seal. The glass is joined on two sides longitudinally. It is heavily embossed, in capital letters, around the base of the side around its circumference and at the base.Bottom sides: 'The property of Richmond N.S. Brewing Co. Pty. Ltd.' Base: 'R.B.' and underneath these letters 'R.'. and in between and much smaller S.3.bottle, beer, richmond brewery, drink, richmond

Beer came in bottles sold at licensed premises either locally or in larger cities visited during shopping expeditions. The shape of the bottles changed. Bottles were recycled remaining the property of the manufacturer who paid for their return. History of the Richmond Brewery.Historical: Change of bottles - shape, glass, embossing. Collected by bottle collectors. Aesthetic: Display showing embossing & shape especially if in good condition.Clear brown bottle with heavy embossing. The bottom half has straight sides. The top tapers to the opening. Half way up the sides it is heavily embossed with R.B. and underneath these letters R. The face of a tiger features in heavy embossing on the side of the bottle. At the bottom around the circumference and on the base is embossing. There is a broken cork sealing the bottle. Sides: R.B. and underneath this R. with a head of a tiger. Bottom around the circumference: 'The property of Richmond N.S. Brewing Co. Pty. Ltd.' Base: '650'beer, drink, bottle, richmond brewery, richmond