Van 3 NUU - Louvred Truck (11) VR Service History 3/12/1900 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1898 - 1911 Number Built 14 In use 5 To be restored None *NUU 3.VA - 3/12/1900 NWS Built new - / /1926 - To NU 3.VA - NU 3.VA - circa 1926 - Modified AC Malco 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 NUU The standard louvre van design for the Victorian narrow-gauge lines, the NUU vehicles were constructed in three batches; the first seven from 1899 to 1901, an eighth in 1906 and the last six in 1911, for a total class of fourteen. They looked very similar to the U vans of the Broad Gauge, although two photographs[1][2] of NUU 1 show that its body may have been white for some time. NU In 1926 the class was relettered to simply NU, with no changes to numbers. NU 4 was scrapped in 1938, but otherwise the class remained intact until 1954, when seven members (2, 5, 7, 8, 9, 11 and 12) were sold to Coulston & Hyder, who dispersed the wagons among locations on the Wangarrata to Whitfield line. As of 1996, vans 7 and 12 were at Moyhu, while van 11 was destroyed by fire in 1978. Wagons 6 and 1 were scrapped in 1957 and 1958 respectively, while in 1954 van 13 was recorded as being sold to the Puffing Billy Preservation Society. In 1977, the remaining vans 3, 10 and 14 were handed over to the Emerald Tourist Railway Board, and removed from Victorian Railways records. The Puffing Billy Railway now posesses vans 3, 8, 10, 13 and 14. Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered VanWooden Louvered Van - Made of Timber on a Wrought iron frame3 NUUpuffing billy, 3 nuu, louvered van, 2'6" guage, victorian railways, narrow gauge rolling stock

Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 6A Loco: 6A In service Thursday, 18th July 1901 Livery Green Owner Puffing Billy Gauge 762 Status Preserved - Operational 6A Built in 1901 and painted two-tone green, this locomotive was issued to the Colac to Beech Forest line and was used in that line’s construction. Over the years, it saw service on all four lines, but mostly on the Colac to Crowes and Upper Fern Tree Gully to Gembrook lines. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it saw almost continuous service until being withdrawn in 1983. It has been restored, as far as possible, to its original condition with original design side tanks, low bunker, original size windows, etc., but a steel cow-catcher in place of the original style wooden one. It also has its original colour scheme of two-tone green with white lining.Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 6ANumber Plate 6A Fabricated steel number board made by the Victorian Railways for locomotive 6A. 6A6a, puffing billy, number plate, victorian railways

Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 6A Loco: 6A In service Thursday, 18th July 1901 Livery Green Owner Puffing Billy Gauge 762 Status Preserved - Operational 6A Built in 1901 and painted two-tone green, this locomotive was issued to the Colac to Beech Forest line and was used in that line’s construction. Over the years, it saw service on all four lines, but mostly on the Colac to Crowes and Upper Fern Tree Gully to Gembrook lines. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it saw almost continuous service until being withdrawn in 1983. It has been restored, as far as possible, to its original condition with original design side tanks, low bunker, original size windows, etc., but a steel cow-catcher in place of the original style wooden one. It also has its original colour scheme of two-tone green with white lining.Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 6A6A Number Plate. Fabricated steel number board made by the Victorian Railways for locomotive 6A. 6Apuffing billy, victorian railways, number plate, 6a

Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 7A Loco: 7A In service Saturday, 6th May 1905 Livery Maroon Owner Puffing Billy Gauge 762 Status Preserved - Operational 7A Built in 1905 and painted Canadian red & dark brown, this locomotive was issued to the Wangaratta to Whitfield line and saw service on all four lines with most of its service on the Upper Fern Tree Gully to Gembrook line. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it has seen almost continuous service since. 1979 saw the early two-tone green colour scheme applied to this loco as a trial even though it never historically carried it, but its physical configuration was not altered accordingly. It is now painted its original livery of Canadian Pacific red & dark brown and will eventually be returned, as far a possible, to its original condition with a low bunker, narrow ash-chute, etc.Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 7ANumber Plate 7A Fabricated steel number board made by the Victorian Railways for locomotive 7A7apuffing billy, 7a, number plate, victorian railways

Steam Locomotive - 1711 Peckett “Sir John Grice” Date built - 1926 Locomotive type ; Cranmore Original owner - Metropolitan Gas Coy., West Melbourne Original gauge - 762mm Withdrawn - 1941 Next owner - Whistle Stop Amusement Park, Frankston Built in 1926 for the West Melbourne site of the Metropolitan Gas Company, and issued to traffic the same year this saddle tank locomotive was named “Sir John Grice” in 1928. It was withdrawn from traffic in 1941 and stored until sold privately in 1962. In 1965 it was sold again and went to the Whistle Stop Amusement Park in Frankston and again stored until bought at auction by the Puffing Billy Preservation Society in 1974 and put on static display in the Steam Museum. Restoration started in 1978 and it was returned to service in 1981 painted light green with yellow lining. It is temporarily renamed “Thomas the Tank Engine” with a fibreglass “Thomas” body cover each time it appears in the “Thomas the Tank Engine” shows at Gembrook station.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used at the Metropolitan Gas Coy., West Melbourne, Victoria, AustraliaSteam Locomotive made of steel, wrought iron Peckettpeckett “sir john grice”, 1711 peckett, puffing billy, steam locomotive, industrial narrow gauge railway, metropolitan gas coy., west melbourne

Construction of the Colac-Beech Forest railway line began in 1900 with about 100 men engaged in laying and ballasting the track, as well as others forming the earthworks and building culverts and bridges. The result of this labour saw the railway advance from Colac until it climbed a spur hugging the side of a forty degree slope emerging on top of the ridge at Beech Forest. This photograph was taken 28 miles (45 kilometres) from Colac between Devitt Bros. Siding and Ditchley, just out of Beech Forest. Two 2-6-2 Tank engines of the narrow-gauge A class built by Victorian Railway's Newport workshop, were commonly dubbed 'Coffee Pots'. As well as pulling a load of NQR wagons a NBB saloon car ended the train. The devastation to the standing timber was deliberate: the Engineer-in-Chief of VR ruled that all trees within a certain distance of the railway line were to be cut down. This certainly saved the line from destruction several times in the future.B/W. An NA class locomotive, NQR wagons and an NBB saloon car, all with workmen, going around a bend between Devitt Brother's Siding and Ditchley on the Beech Forest line in 1901.beech forest; ditchley; devitt bros siding, railways;

These minutes contain information on attendees, meeting chairs, apologies, correspondence, subscriptions, donations, legacies and general business. Reports are also included from Auxiliaries, Auditors, Library and Home teacher, Directors, The Black and White committee, Victor Maxwell House, Helen Keller Hostel, The Victor Maxwell Kindergarten, The Sandy Robertson Kindergarten, Alexis Albert House, Lighthouse, Silver Lighthouse committee, Newcastle Branch, 'Heathfield' and other Woollahra properties. 22/3/1965 it was noted to assist blind persons with the transfer to Decimal Currency an application had been made to the Commonwealth Treasurer for early release of specimen coins and notes. 24/1/1996 it was resolved that a dollar note gauge be supplied to all blind persons in N.S.W. 30/11/1966 it was noted the Management Committee had recommended to Council that the Society should transfer all its activities currently conducted at Williams Street to Mitchell Street and that the William Street be offered for sale at not less than $700,000. 1 volume of typed sheets glued to pagesroyal blind society of nsw, annual reports

DH5 Diesel Hydraulic locomotive The DH class was a class of diesel-hydraulic locomotives built by Walkers Limited, Maryborough for Queensland Railways between 1966 and 1974. In 1966 Queensland Railways tested a Walkers Limited built diesel-hydraulic shunting locomotive. This was later purchased and by 1974 the 73 DH class locomotives had taken over shunting duties in most Queensland yards. They were also used on short distance freight services. With the closure of many freight yards and the move to longer trains withdrawals started in the 1980s. Many were sold for further use on Queensland sugar cane railways. Locomotive's Queensland Railways Service History : Locomotive : DH5 Serial No: 587 In Service : 27/08/1968 With drawn from Service : 7/07/1992 LOCOMOTIVE DETAILS DH class No. originally constructed : 74 No. in service : 2 No. stored : Wheel arrangement : Bo-BoDH Roadworthy weight : 40T Maximum axle load : 10T Tractive effort (85%) Length overall: 33' Height overall : 12' 6 1⁄2" Driving wheel diameter : 36" Date of manufacture :1970 Manufacturer :Walkers Place of manufacture : Maryborough, Queensland Locomotive type : Diesel Hydraulic DESCRIPTION - B-B DH FORMER CLASS AND NUMBER - 8/1968 Built By - Walkers, Maryborough, Queensland Service History Date built - 1968 Original owner - Queensland Government Railways Original gauge - 1067mm Withdrawn - Next owner - State Electricity Commission of Victoria DH5 8/1968 Sold to SECV as CC2, In service 8-1993 Sold to Mackay Sugar CC02 (Ex DH5). CC02 was purchased by Cooks Construction in 1992 and used on the 900mm Yallourn railway in Victoria. Mackay Sugar purchased in 2001. Title Value Status Preserved - Operational Gauge Narrow 2ft 6in (762mm) Owners Puffing Billy Railway Operators Puffing Billy Railway Manufacturer Walkers Ltd - Maryborough, Queensland Builders number 587 Associated locos Renumbered from CC02 Liveries carried VR Blue & Gold Puffing Billy Service History or Notes Date acquired - 2008 Acquired from - Mackay Sugar Mill ? State when acquired - Operational ? Work done - Regauged, overhauled Restored to service - Current State - Operational Historic - Queensland Railways - Diesel Hydraulic locomotive DH5DH 5 Diesel Hydraulic locomotive made of steel and metalDH 5puffing billy railway, dh5, locomotive, cc02, diesel,, queensland railways, diesel hydraulic locomotive dh5, walkers diesel hydraulic

2287.1 - Four page technical pamphlet, titled "Combined Guard's Van Valve and Gauge for Vacuum Brakes", published by Westinghouse Brake and Saxby Signal Co. Ltd. November 1926. Manual No. D.P. 8. 2287.2 - Eight page technical pamphlet, titled "Brake Control Valve for Automatic Vacuum Brake", published by Westinghouse Brake and Saxby Signal Co. Ltd. January 1928, Manual No. D.P. 15. Saddle Stapled. 2287.3 - Twelve page technical pamphlet, titled "Vacuum Brake Apparatus", published by Westinghouse Brake and Saxby Signal Co. May 1924, Manual No. D.P. 3. Saddle Stapled. 2287.4 - Eight page technical pamphlet, titled "Prestal Vacuum Brake Cylinders Combined and Separate Types", published by Westinghouse Brake and Saxby Signal Co. Ltd. January 1928, Manual No. D.P. 14. Saddle Stapled. Two copies held.Each have "Colin Rutledge" stamped on top of page 1.trams, tramways, westinghouse, railway brakes, vacuum brakes, equipment

The Ballarat School of Mines Annual Report 1891. Annual Report, Crown Grant, Affiliation Statute, Constitution, Examination Statutes, Associateship of The School, Certificates Granted by the Council, Clunes Branch Report, Departmental Expenditure, Fees, Form of Bequest, Gauge-Testing Apparatus, General Balance Sheet and Liabilities and Assets, Honorary Correspondents, Life Governors, Meteorological Observations, Number of Students attended The School of Mines, Office Bearers, Practical Treatment of Ores, Report of the Professor of Mineralogy and Geology and Curator of the Museum, Report of the Superintendent of Laboratories, Report of the Lecturer on Engineering and Surveying, Report of the Lecturer on Mathematics, Report of the Lecturer on Electrical Engineering and Telegraphy, Report of the Lecturer on Botany, Report of the Lecturer on Geometrical and Freehand Drawing, Report of the Lecturer on Materia Medica and Physiology, Report of University Classes, Report on Mining Laboratory, Examinations Held, Scale of Charges for Assays and Analyses, Statement of Receipts and Expenditure for the year 1891 and Special Trust Funds, Statistics - Students attending Lectures, Subjects and Lecturers, Subjects and Examiners, Subscriptions and Donations from 1st January to 31st December 1891, Syllabus of Lecture CoursesThe Ballarat School of Mines Industries and Science Annual Report, 1891. Cover is browning around the edges, front cover has small tear on bottom of cover, 132 pages. ballarat school of mines, annual report, andrew anderson j.p. - president, f. j. martell - vice president, r. denham pinnock - vice president, rivett henry bland - trustee, the hon. sir w. j. clarke - trustee, the hon. john warrington rogers - trustee, james oddie - trustee, the hon. henry cuthbert - honorary solicitor, c. eyres - honorary treasurer, charles kent - auditor, andrew berry - registrar, f. m. krause - professor of mineralogy and geology, and curator of the museum, alf. mica. smith - chemistry, metallurgy, natural philosophy, f. m. krause - geology, mineralogy, geological surveying, j. h. horwood - lecturer on engineering and surveying, h. j. hall - lecturer free-hand and model drawing, george day - botany, j. f. usher - materia medica and physiology, c. w. wilson - university classes, isaac jaques jones j.p., mr e. wattis - manager, mining laboratory, j. a. dawson - electrical engineering and telegraphy, elder gray, harry e. sando, charles matthews - auditor, j. h. daley - auditor, henry crone - assistant registrar of titles, henry b. loch, isaac jacques jones, charles eyres, j.a, j.a. dawson, statistics, university classes, bella guerin, c.w. wilson, clunes branch of the ballarat school of mines, w.e. burbridge, h.j. hall, museum, state school students, daniel walker, a.j. higgins, state school science classes

Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 5A Loco: 5A In service Saturday, 23rd March 1901 Scrapped Monday, 7th July 1958 Livery Black Owner VR Gauge 762 Status Scrapped Service History : Mar 1901 Colac - initial allocation of a new locomotive Mar 1901 - Feb 1902 Colac Dec 1902 - Oct 1908 UFTG. Nov 1908 - Oct 1912 Colac Nov 1912 - May 1913 Other Jun 1913 - Jun 1915 UFTG. Sep 1915 - Sep 1920 Moe Oct 1920 - Nov 1921 UFTG. Mar 1922 - Jan 1927 Colac Mar 1927 - Aug 1927 Moe Oct 1927 - Jan 1928 UFTG. Feb 1928 - Dec 1934 Colac Jan 1935 - Mar 1935 Moe Apr 1935 - Sep 1942 Colac Mar 1943 - Mar 1949 Moe Apr 1949 - Nov 1957 Colac Dec 1957 Colac - Stored. Feb 1958 - Jul 1958 Workshops - ScrappedHistoric - Victorian Railways Locomotive Number Plate used on Steam Locomotive 5AVictorian Railways produced 5a number plate. made of cast iron5a5a, puffing billy, victorian railways

VR Commissioner's Special train, steam locomotive D3-639 crossing the Echuca-Moama Road Rail Bridge over the Murray River from Moama, NSW to Echuca, Victoria. Commissioner Edgar Henry Brownbill on footplate, 1962. Commissioner Edgar Henry Brownbill was in office 1957 to 1967. George Coop advises - "The train on the Eltham/Moama bridge is actually the Commissioner’s Special on one of its inspection tours of the VR rail system. This was a very grand special train with accommodation for the Commissioner and staff in carriages also used once for the Royal Train and other State purposes. You can just see the Commissioner of the day, dressed in his suit and wearing engine drivers gloves, standing in the loco cab doorway. A good ‘hands on’ impression is created amongst local staff if can be seen that the boss is no ‘desk jockjey’. The observation car on the back was originally made for the ’Spirit of Progress’. I climbed up onto the bridge iron plate work to get this view. It was safe enough as the cantilevered pedestrian walkway was still on the east side at the time." "I was resident in Echuca from Jan. ’59 to approx. May ’64. At that time the single Echuca/Moama bridge was a combined road/rail bridge. The rail gauge was 5’3” and still is, I believe, on the new bridge that sits just upstream of the old one. This rail line into NSW has always been 5’3" gauge because it has no connection with any NSW tracks. The old Echuca/Moama bridge, locally called the ‘Iron Bridge’ has, over years, undergone some structural changes. The two lattice iron hoops arcing over the roadway have been raised and lowered and changed design. Presently a pedestrian walkway is cantilevered off the west (or downstream) side of the bridge. It used to be on the eastern side. Guess changes went in when new rail bridge only was built on the eastern side as well." Image dated as c.1963 based on same image in Port of Echuca collection (possibly frame 32 of film) (print 19.5 x 24.5cm) On reverse in pencil: "Brown card" in black pen: "Commissioners special. F. Brown on Footplate. George C.L. Coop c1963". https://victoriancollections.net.au/items/59d575b921ea6e1278d78042 However based on frame no. 10, date set as 1962Digital TIFF file Scan of 35mm Ilford FP3 black and white negative transparencyd3-639, d3-class steam locomotive, echuca-moama road rail bridge, edgar henry brownbill, george coop collection, murray river, vr commissioner's special train

Replica of a Victorian Railways replacement number board that 6A carried in the later 40's and 50's. This plate was created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek. Loco: 6A In service Thursday, 18th July 1901 Livery Green Owner Puffing Billy Gauge 762 Status Preserved - Operational 6A Built in 1901 and painted two-tone green, this locomotive was issued to the Colac to Beech Forest line and was used in that line’s construction. Over the years, it saw service on all four lines, but mostly on the Colac to Crowes and Upper Fern Tree Gully to Gembrook lines. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it saw almost continuous service until being withdrawn in 1983. It has been restored, as far as possible, to its original condition with original design side tanks, low bunker, original size windows, etc., but a steel cow-catcher in place of the original style wooden one. It also has its original colour scheme of two-tone green with white lining.Historic - Replica Victorian Railways Locomotive Number Plate of the type used on Steam Locomotive 6A in the later 40's and 50's created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek. Number Plate 6A Cast aluminum replica number board.6Apuffing billy, menzies creek, 6a, number plate

Replica of a Victorian Railways replacement number board that 7A carried in the later 40's and 50's. This plate was created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek. Loco: 7A In service Saturday, 6th May 1905 Livery Maroon Owner Puffing Billy Gauge 762 Status Preserved - Operational 7A Built in 1905 and painted Canadian red & dark brown, this locomotive was issued to the Wangaratta to Whitfield line and saw service on all four lines with most of its service on the Upper Fern Tree Gully to Gembrook line. It was temporarily withdrawn from service in 1958 and returned to service at Belgrave in 1962 for the reopening of this line where it has seen almost continuous service since. 1979 saw the early two-tone green colour scheme applied to this loco as a trial even though it never historically carried it, but its physical configuration was not altered accordingly. It is now painted its original livery of Canadian red & dark brown and will eventually be returned, as far a possible, to its original condition with a low bunker, narrow ash-chute, etc.Historic - Replica Victorian Railways Locomotive Number Plate of the type used on Steam Locomotive 7A in the later 40's and 50's created for the preservation society's reenactment trains in 2012 for the 50 year celebration of reopening to Menzies Creek Number Plate 7A Rectangular black and white number plate. Cast aluminum replica number board.7Apuffing billy, 7a, number plate

Number Plate 14A Loco: 14A In service Thursday, 25th June 1914 Withdrawn April 1962 Livery Red Owner Puffing Billy Gauge 762 Status Preserved - Operational 14A Built in 1914 and painted Canadian red & dark brown, this locomotive was issued to the Colac to Crowes line and saw service on all four lines, but mostly on the Colac to Crowes line. It was withdrawn from service in 1962 at Colac and sent to Newport Workshops for storage where it remained, except for a brief time at Bendigo North Work-shops in 1963. After overhaul, it was brought to Belgrave in 1965 where it has seen almost continuous service since. In 1978, it became the first of the preserved NA’s to trial a historic colour scheme for which the Canadian red & dark brown was chosen, but ended up mistakenly being painted a “London Tan” & dark brown. In 1996 it received a more correct Canadian red livery. This “temporary” trial livery has now given way to 14A’s designated livery of all-over black. Its physical configuration will match the late 1940s era with the extended bunker, guard irons, etc.Historic - Victorian Railways Locomotive Number Plate used on Steam Locomotive 14ANumber Plate 14A Rectangular black and brass number plate. Cast brass number board.14Apuffing billy, 14a, number plate

testCalendar - large wall with clear plastic sheet - spiral wire bound at top issued by Comeng Rolling Stock division of ANI Corporation in 1985. Features 6 paintings by Phil Belbin. 1 - (Jan - Feb) NSW 8029 leading the southbound Intercapital Daylight out of the Bowral tunnel. 2 - (Mar - Apr) - trams 939 and 918 - Victoria Parade reserved track. 3 - (May - Jun) - South African Railways Blue Train 4 - (Jul - Aug) - VR S300 and 301 5 - (Sep - Oct) - QR 1298 on the Sunlander crossing a 2' gauge cane steam loco. 6 - (Nov - Dec) - Commonwealth Railways - Rawlina - Transcontinental train leaving Rawlinna - with the Tea and Sugar Train. For details of the artist see - https://en.wikipedia.org/wiki/Phil_Belbin (accessed 2-1-2018). See btm7022note from Bruce Belbin his son re use of the image. tramways, trams, art work, painting, victoria parade, railways

Copy of the Australian Railway Enthusiast - Vol 9, No. 4, December 1971, which contains seven photographs of the closure of the Ballarat Tramway System on 19/9/1971 by Greg Triplett. Item 579 refers for centre page photograph. Magazine has articles on the Beech Forest Narrow Gauge, The Atjeh Tram (Indonesia), cable cars preserved in Melbourne and a derailment at Yering Vic. in 1900. Ballarat Photos 1 - 40 in Lydiard St. 2 - Bogie car in Wendouree Parade from the wheat silos 3 - Intersection of Sturt and Lydiard Street from the Town Hall 4 - Tram at City Centre with Boer War (?) statue in front of the tram - night photo 5 - 35 at Sebastopol Terminus - night photo 6 - 42 at the Lydiard Street terminus - night photo 7 - 40 leaving Sebastopol as the last tram - night photo (see item 579) Second copy added 31-8-2017. Second copy has a "Technical Book & Mag. Co." yellow label on the front cover.trams, tramways, ballarat, closure, lydiard st, sturt st, sebastopol

Set of thirteen colour photographs of the repair of the broken joint in Wendouree Parade as part of the track works in the area. Photos taken on 15 and 16/3/2003, printed on AGFA paper. 2555.1 - Gary Wood, Oedf Byslma looking at the excavated area, with sleeper cutting going on in the background. 2555.2 - Gary Wood and Alan Snowball, cleaning rails and the area, shows status, which was tight to gauge. 2555.3 - Removing sleepers. 2555.4 - First sleeper installed. 2555.5 - Cutting sleepers to length - Rolf Jinks and Andrew Mitchell. 2555.6 - Installing sleepers. 2555.7 - All 4 new ones positioned. 2555.8 - Cutting bolts from old plate. 2555.9 - Bending the rail. 2555.10 - Tram 33 at the temporary terminus. 2555.11 - Rail repositioned. 2555.12 - Installing the screw spikes - Gary Wood, Alastair Reither, Andrew Mitchell and Alan Snowball. 2555.13 - Welding the plates etc - 16/3/2003 - Alan Snowball.trackwork, wendouree parade, track, tram 33

Greenbat Battery Loco Built by Greenwood & Batley Ltd Builders No. 420363/2 This Greenbat Battery Loco has been loaned to the Museum by the Walhalla Goldfields Railway, who had acquired it in 2013 along with a large quantity of narrow gauge trollies and light rail from Orica’s now closed munitions factory in Melbourne’s western suburbs. The trolley on display was one of two in use from the 1970s. Orica - Deer Park Munitions factory Orica Deer Park in Melbourne’s west has been used since circa 1875 for various forms of manufacturing and storage of chemicals. Although the site is bounded by Ballarat Road, Station Street, Tilburn Road and the Western Ring Road, the current entry point for industrial operations is situated at Gate 6 off Tilburn Road. Operations include: • a specialty chemicals facility producing products for mining services operations • quarry services • other chemical manufacture activities. The Deer Park factory complex is of historical significance as the location of the first plant for the manufacture of high explosives in Australia and has been, for its entire history, the most important, if not only, commercial manufacturer of high explosives in Australia. It commenced operation under the importer Jones Scott and Co, and then the Australian Lithofracteur Company (Krebs Patent), a rival to Nobel's dynamite patent. The factory was producing nitro-glycerine based explosives in Australia only a couple of years after Nobel's Ardeer factory began operating in Scotland. The explosives factories complex is of historical significance for the association with the Australian Lithofracteur Company, Australian Explosives and Chemicals, the Nobel company and later ICIANZ, which grew to become one of the largest explosives, chemical and plastics manufacturers in Australia. It was the pioneer of the industry and retained its dominance through monopolistic practices, taking over most of its competitors in the Australasian region. Substantial parts of the pre-Second World War layout of the site remain which, with a number of significant buildings dating back to the 1920s and '30s, indicate past and present processes of manufacturing, the necessary safety measures required and the integrated nature of the explosives and chemical industry. The narrow gauge tramway, which ran through the explosives section, was a rare survivor of nineteenth century materials-handling methods into the 21st Century. Greenwood & Batley were a large engineering manufacturer with a wide range of products, including armaments, electrical engineering, and printing and milling machinery. They also produced a range of battery-electric railway locomotives under the brand name Greenbat. The works was in Armley, Leeds, UK. Greenbat was the trade name for the railway locomotives built by Greenwood & Batley. The company specialised in electric locomotives, particularly battery-powered types for use in mines and other hazardous environments. Historic - Industrial Narrow Gauge Railway - Battery Locomotive - Orica - Deer Park Munitions factory - Deep park, Victoria, Australia Battery Locomotive - made of iron puffing billy, greenbat battery loco, battery locomotive, industrial narrow gauge railway, orica - deer park munitions factory

A scotch eye auger is perfect for quickly making holes in dry or wet wood for making chairs, stools, and any number of woodworking projects. The scotch eye serves as a peg gauge and whatever peg you make to go into the hole should fit into the augers eye. Robert Sorby & Sons: The forbearer's of Robert Sorby had been cutlers in the Sheffield region of England, dating from the mid 17th century. Robert Sorby and Sons were registered in Sheffield in 1828 as a manufacturer of edge tools, saws, scythes and hay knives. In addition to manufacturing tools, they also diversified into the manufacture of crucible steel for tool manufacture. From circa 1860-1967, the Sorby factory in Sheffield was known as the “Kangaroo Works”. The Kangaroo Brand of tools was made by Robert Sorby & Sons. During the 19th century, they had a large trade in Australasia. By the early 20th century, they were manufacturing carving tools, planes and plane irons, circular saws, wood saws, butchers saws and cleavers, garden tools, pruning knives, coopers’ knives, bricklayers tools and joiners tools. In 1923 Robert Sorby & Sons was bought by Sheffield company Hattersley and Davidson. They are today one of the few remaining British tool manufacturers.The company has a long tradition of making edged tools for various uses and exporting them to Australia, however the subject item was probably made from the early 20th century up until 1967 when the company stopped exporting to Australia.Scotch Eye Auger, Double Twist with Lead Screw, square shaft, socket set at right angleRob Sorbey Sheffield stamped on shaft with Kangaroo trade markflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, ring auger, carpenders tools, hole drilling, rob sorby & sons

Sub Nigel Gold Mines No. 3 Wheels: 0-6-0 WT Builder: Orenstein & Koppel Build Date: June 1931 Construction No.: 12331 Empty Weight: 10 tons 7 cwt Weight in working order: 12 I/2 tons Driver Diameter: Unknown Tractive Effort: Unknown Boiler Pressure: 185 lbs Cylinders: Unknown Fuel: Coal Gauge: 2 ft 6 in (760mm) Builders Number 12331 Used to haul gold bearing ore from mine to reduction works at the Sub Nigel Mine at Dunnattar, Transvaal, South Africa. It was the first locomotive fitted by roller bearings by SKF and featured in the SKF catalogue at the time. This interesting 0-6-0WT locomotive was built by Orenstein & Koppel in 1931 as their builder's number 12331, becoming No.3 in the locomotive fleet at the Sub Nigel Gold Mines Ltd, South Africa. No.3 was obtained by the Puffing Billy Preservation Society and imported to Australia in the early 1970s. It arrived at the museum on 30th Jan 1973. It has since been displayed at the Puffing Billy Museum, Menzies Creek. Details from http://www.australiansteam.com/ok12331.htm Donated by Gold Fields Property Co. Ltd South Africa in 1973.Historic - Industrial Narrow Gauge railway - Steam Locomotive with SKF Roller bearings - used at the Sub Nigel Mine at Dunnattar, Transvaal, South Africa.Steam Locomotive - Steel (Painted)The Sub Nigel Ltd / 12331puffing billy, steam, locomotive, orenstein, koppel, sub nigel mine, skf roller bearings, sub nigel no. 3

Skippy St Elmo - Champion Skier and High Country Housewife. For much of the winter 1945 newly married Skippy St Elmo was alone in Wallace's Hut while her husband Toni worked as an assistant hydrographical observer for the SEC. During her first two weeks Skippy had her first ski lesson and promised herself that someday she would be able to ski. Before winter's end she was accompanying Toni around the snow gauges. The following year, Skippy and Toni became the first full time residents of Falls Creek. Along with a group of other SEC workers they built the first lodge at Falls Creek, “Skyline” in 1947. Not only did Skippy fulfill her promise to be able to ski but also went on to become the Victorian Women's 1949 Downhill & Combined Champion and in 1954 won the Albury Ski Club Men's championship. While modest about her skiing success, Skippy was very proud of her domestic skills and cooking prowess using a camp oven. She also was spent time sewing ski wear for both Toni and herself. Skippy definitely earned the title of “Falls Creek’s First Lady”.This item is significant because it documents a pioneering figure of Victorian skiing.Poster composed of photos and text explaining basic information about Skippy St. Elmo mounted on display board.skippy st elmo, key figures of falls creek, skyline

Ward Brothers (George and Samuel) registered a company (Australian Sewing Machines Limited Pty Ltd) with the head office address in Errol St, North Melbourne, and Prahan. The earliest newspaper advertisement for this company was in 1897. Around this time the Ward Brothers first imported sewing machines from England and Wertheim placed their decal on them and mounted them in their own Australian made cabinets. David Ward later imported machines from Beisolt & Locke in Germany and registered name  A.N.A. (All Native Australian), his shop was in Collingwood Melbourne. Some of these machines had Ward Brothers decals on them as well. The three brothers sold under the same name as Ward Brothers. The early Ward Brothers logo had a map of Australia with a picture of all three brothers on it. In 1911 all three of the Ward Brothers decided to share a stall in the yearly Melbourne exhibition. The A.N.A was the machine that got rave reviews. It was at this time that the Australian Sewing Machine Company Pty Ltd decided to add the A.N.A logo to their logo to cash in on the new found celebrity status that the A.N.A has gained. To cut a long story short. David Ward took his brothers to court to prevent this from happening. This was a long drawn out affair that took quite a few years. The settlement was decided out of court and nothing was disclosed of the deal that was made. David seemed to have left the scene, then the remaining Ward Brothers and A.N.A. combined and then became “Wardana”. There are many Ward Brothers sewing machines in displays, they originated from Japan, England, America, and Germany. It seems that where ever they got the best deal for sewing machines or parts is the direction they went. This is where the Bendigo sewing machine company came into the picture. All imported sewing machines into Australia drew a government tax. Bendigo Cording's Traction Company was given proposed two-pound tariff protection that gave the company a significant price advantage for its machines. As a result, the Ward Brothers purchased a huge number of Bendigo shares to get cheaper machines for their sewing machine cabinets. Ward Brothers then placed one of their company officials on the Board of “Bendigo Sewing Machines Limited” and the rest is history. Ward Brothers had shops Australian wide and in most of the major country towns. History for “Bendigo Sewing Machines Limited”     Cordings Traction Company owners (H. Keck MLC, W. Wallace, and W. Ewing) operated their business out of the former W. Webb & Co. building in Queen St. Bendigo. Around 1923-1924 they decided to switch from traction engines to manufacturing sewing machines. The actual date is not known but that year's financial report made note of both Cordings and Bendigo Sewing Machines Limited. The switch was made with the government of the day agreeing to a tariff of two pounds per head for every machine head made completely in Australia. The change from traction engines to sewing machines went well. Government representatives visited the factory in Bendigo to inspect and ensure that the sewing machines were Australian made as a result they agreed on granting the two-pound tariff to the company. After the first 12 months, they built 30, the following 12 months the company had produced 1500 machines probably due to the involvement of the Ward brothers. However, the government proposed a new condition to the tariff agreement which was that the company must produce 20% of Australia's requirements for sewing machines. In 1924 after having had produced 1500 machines resulting in reaching their financial limit for tariff support. According to the government, the requirement was 15,000 machines for the next year had to be produced to qualify for the tariff. The company had already reached its production limit and unfortunately folded. There were several attempts to regain government assistance to save this new industry but it was to no avail. Even a promise to open another factory in Sydney was offered but unfortunately wasn't accepted. An item fabricated in Australia from a majority of imported parts from either Germany, America or England giving a snapshot into the early manufacturing industries that were operating at the time of Federation. Sewing machine, treadle, in timber cabinet. Branded Ward Bros, A.N.A., Australian Sewing Machine Coy. Decorative carved timber cabinet, hinged, fold-out laminated timber top and five drawers; two small on each side with handles and one long, shallow, between side drawers without handle. Thread is on bobbin in a rocket shuttle (both in good condition) plus spare empty shuttle (rusty). Brass ‘Half Yard’ ruler inlaid across front, measuring scale in inches and centimetres. Two metal shuttle cover plates (or throat plate / slide plate); front one is impressed with a gauge for needle and thread. Gold trim and decals on flatbed and machine front and back, serial number under shuttle cover, brand on decals and on round metal plate on back of machine. Front right of machine has a bobbin winder. Treadle belt shows signs of wear and laminate on timber machine cover is peeling slightly.Decal coat of arms on right front of machine: kangaroo on left, man with broad-brim hat, holding pick-axe on right, in centre, top “SEWING MACHINE / THE / A. N. A.” then below it, the rising sun, then below that is state of Victoria shield with the Southern Cross constellation. Wheat sheaves around edge on left and flowering plant on right. Gold ribbon banner at bottom with script “WARD BROS.“ Decal of map of Australia on flatbed of machine. States and capital cities are marked and named (no northern territory), portrait of two men. In centre of map are interwoven letters “A. N. A.” and written in script “WARD BROS.” Decal across front of machine body has large, decorated gold lettering “A. N. A.” Decal across the top of machine “THE AUSTRALIAN SEWING MACHINE COY. PTY. Ltd.” Steel shuttle cover at front has an impressed gage listing cotton and needle sizes and number of stitches. Brass disc on back of machine “A. N. A.” in centre. Brass ruler across front of machine has carved or pressed words in the timber. In centre “INCHES” above ruler and “CENTIMETRES” below ruler, and on right above ruler is “HALF YARD” Decal across back of machine’s body “A.N. A. / MADE IN U.S.A.” Stamped into metal under shuttle cover is “219415” (2 and 5 are partially there, first 1 could instead be a 7) flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, ward bros., australian sewing machine co., a.n.a., treadle sewing machine, rocket shuttle sewing machine, home industry, clothing, wardana, australian sewing machine company, all native australian, dressmaking, clothing manufacturer

This memorial was erected by the residents of Apollo Bay and District in 1922.Colour photograph of the War Memorial at Apollo Bay, that features a scuplture of an Australian soldier with slouch hat and holding a rifle. It includes a list of those who served during World War One and World War Two. A characteristic figurative monument, the memorial comprises a single standing soldier, looking down the main street, a top a polished granite pedestal with honour roll set on a huge rock faced granite block.The memorial is fenced by heavy set square concrete bollards supporting heavy gauge chain between each. tBuilt by J. Wilson & Co. of Bendigo, the Apollo Bay Memorial depicts the lone soldier, a typical symbol of the sentiments of communities who had lost faith in heroism and had learnt to recognise the level of loss caused by war amongst ordinary volunteers. This recognition,which occurred throughout Australia, marked a turning point as the 'unknown soldier' was increasingly commemorated instead of military leaders as had previously been the traditional practice. apollo bay war memorial, australian soldier memorial, cawood, mitchell, finlayson, marriner, maguire, mclennan, stephens, vipont, lang, turner, thomson, h.f. smith, a.e. hunt, ormsby, elston, gooday, p. bird, costin, de vere, de forest, j. bowie, c. hughes, r. irving, mcminn, newman, riley, sculley, townsend, thornton, thurst, wright, j. wilson, stonemason

This memorial was erected by the residents of Apollo Bay and District in 1922.Colour photograph of the War Memorial at Apollo Bay, that features a scuplture of an Australian soldier with slouch hat and holding a rifle. It includes a list of those who served during World War One and World War Two. A characteristic figurative monument, the memorial comprises a single standing soldier, looking down the main street, a top a polished granite pedestal with honour roll set on a huge rock faced granite block.The memorial is fenced by heavy set square concrete bollards supporting heavy gauge chain between each. tBuilt by J. Wilson & Co. of Bendigo, the Apollo Bay Memorial depicts the lone soldier, a typical symbol of the sentiments of communities who had lost faith in heroism and had learnt to recognise the level of loss caused by war amongst ordinary volunteers. This recognition,which occurred throughout Australia, marked a turning point as the 'unknown soldier' was increasingly commemorated instead of military leaders as had previously been the traditional practice. apollo bay war memorial, australian soldier memorial, cawood, mitchell, finlayson, marriner, maguire, mclennan, stephens, vipont, lang, turner, thomson, h.f. smith, a.e. hunt, ormsby, elston, gooday, p. bird, costin, de vere, de forest, j. bowie, c. hughes, r. irving, mcminn, newman, riley, sculley, townsend, thornton, thurst, wright, j. wilson, stonemason

This memorial was erected by the residents of Apollo Bay and District in 1922.Colour photograph of the War Memorial at Apollo Bay, that features a scuplture of an Australian soldier with slouch hat and holding a rifle. It includes a list of those who served during World War One and World War Two. A characteristic figurative monument, the memorial comprises a single standing soldier, looking down the main street, a top a polished granite pedestal with honour roll set on a huge rock faced granite block.The memorial is fenced by heavy set square concrete bollards supporting heavy gauge chain between each. tBuilt by J. Wilson & Co. of Bendigo, the Apollo Bay Memorial depicts the lone soldier, a typical symbol of the sentiments of communities who had lost faith in heroism and had learnt to recognise the level of loss caused by war amongst ordinary volunteers. This recognition,which occurred throughout Australia, marked a turning point as the 'unknown soldier' was increasingly commemorated instead of military leaders as had previously been the traditional practice. apollo bay war memorial, australian soldier memorial, cawood, mitchell, finlayson, marriner, maguire, mclennan, stephens, vipont, lang, turner, thomson, h.f. smith, a.e. hunt, ormsby, elston, gooday, p. bird, costin, de vere, de forest, j. bowie, c. hughes, r. irving, mcminn, newman, riley, sculley, townsend, thornton, thurst, wright, j. wilson, stonemason

This memorial was erected by the residents of Apollo Bay and District in 1922.Colour photograph of the War Memorial at Apollo Bay, that features a scuplture of an Australian soldier with slouch hat and holding a rifle. It includes a list of those who served during World War One and World War Two. A characteristic figurative monument, the memorial comprises a single standing soldier, looking down the main street, a top a polished granite pedestal with honour roll set on a huge rock faced granite block.The memorial is fenced by heavy set square concrete bollards supporting heavy gauge chain between each. Built by J. Wilson & Co. of Bendigo, the Apollo Bay Memorial depicts the lone soldier, a typical symbol of the sentiments of communities who had lost faith in heroism and had learnt to recognise the level of loss caused by war amongst ordinary volunteers. This recognition,which occurred throughout Australia, marked a turning point as the 'unknown soldier' was increasingly commemorated instead of military leaders as had previously been the traditional practice. apollo bay war memorial, australian soldier memorial, cawood, mitchell, finlayson, marriner, maguire, mclennan, stephens, vipont, lang, turner, thomson, h.f. smith, a.e. hunt, ormsby, elston, gooday, p. bird, costin, de vere, de forest, j. bowie, c. hughes, r. irving, mcminn, newman, riley, sculley, townsend, thornton, thurst, wright, j. wilson, stonemason

This memorial was erected by the residents of Apollo Bay and District in 1922.Colour photograph of the War Memorial at Apollo Bay, that features a scuplture of an Australian soldier with slouch hat and holding a rifle. It includes a list of those who served during World War One and World War Two. A characteristic figurative monument, the memorial comprises a single standing soldier, looking down the main street, a top a polished granite pedestal with honour roll set on a huge rock faced granite block.The memorial is fenced by heavy set square concrete bollards supporting heavy gauge chain between each. tBuilt by J. Wilson & Co. of Bendigo, the Apollo Bay Memorial depicts the lone soldier, a typical symbol of the sentiments of communities who had lost faith in heroism and had learnt to recognise the level of loss caused by war amongst ordinary volunteers. This recognition,which occurred throughout Australia, marked a turning point as the 'unknown soldier' was increasingly commemorated instead of military leaders as had previously been the traditional practice. apollo bay war memorial, australian soldier memorial, cawood, mitchell, finlayson, marriner, maguire, mclennan, stephens, vipont, lang, turner, thomson, h.f. smith, a.e. hunt, ormsby, elston, gooday, p. bird, costin, de vere, de forest, j. bowie, c. hughes, r. irving, mcminn, newman, riley, sculley, townsend, thornton, thurst, wright, j. wilson, stonemason