Contractor with steam engine would travel from farm to farm around district as requestedBlack and white photograph of men at small steam engine used to power chaff cutting machine with four workers in charge. Bark roofed building nearby believed to be at Howlett or Bobribb property Bumberrah Victoriamachinery, agriculture

This model was found in the collection of Bay Steamers Maritime Museum. It is not knowt who created it but it is supposed that it was constructed to educate the many masters of the Wattle in the operation of a steam engine - a not so common mode of power these days. A Bay Steamers Maritime Museum examined the model in March 2012 and discovered that is was in poor repair. Using his existing knowledge, and with reference to some historic texts, he made some repairs and returned the model to working order. Here is his anaylsis of the situation as an excerpt from the Bay Steamers Maritime Museum newsletter Steamlines May 2012 "I was confronted with a model of a steam engine used years ago as a training aid for hopeful steam engineers. Already having a knowledge of steam operations, I considered a museum write-up for that model a ‘piece of cake’. However, on turning the model’s crankshaft, the valve timing seemed ‘out of kilter’ with the movement of the piston. Problem was that the two eccentrics on the crankshaft were not properly secured to it. Eventually I fastened the two eccentrics to the crankshaft where I felt that they should be and then realized that one of them had a chain-driven valve-timing device attached. This would be adjusted while an engine was running to achieve best performance and fuel economy whilst in operation by accurately controlling the period of time during which steam under pressure from the boiler would be admitted to the cylinder and give greater time for the steam to expand in the cylinder, move the piston and turn the crankshaft and thus, drive the attached apparatus. When the valves were correctly set up it was then possible to get the model to function properly.The model comprises a green section, which is the actual the model mounted on a brown painted board. There are two parts of the model, painted white representing the steam passages, and black representing the cast- iron portions of the cylinder-block casting, and of the main valve sliding between the cylinder a second sliding valve. Of the black portions, one slides back and forth being connected to a rod which is connected to an eccentric clamped to the crankshaft and is the nearer to the flywheel of two eccentrics. This eccentric is attached to the crankshaft at an angle of 90 degrees to the crank-pin attached to the flywheel. To operate the model simply turn the flywheel by means of the handle attached to its crank-pin. A second eccentric is also attached to the crankshaft, further away from the first eccentric, and it is adjusted to operate 90 degrees from the first eccentric (that is, 180 degrees from the crank-pin) A piston (painted silver) is located in a plastic cylinder and has a piston rod which passes through one end of the cylinder, (in actual practice a steam-proof gland seals the cylinder against loss of steam) terminating in a cross-head slide between four rails guiding it. From this cross-head, a connecting rod joins the piston-rod to the flywheel via the crank-pin attached to the flywheel which is part of the crankshaft. (In actual practice, a flywheel may not be used, particularly in a multi-cylinder engine.) The white portions of the model painted nearest to the cylinder represent the two steam ports cast into the main cylinder block, whilst one section painted in between those two represents the exhaust outlet (which may be connected to a condenser to conserve water, or to the open air). The main slide valve has three white-painted portions painted thereon. It has two white-painted marks representing the steam passages to the steam ports into the cylinder, and a third section in between the other two, being that part of the valve through which exhaust steam passes in line with the ports in the cylinder block. By rotating the flywheel, the operations of an engine will be observed as steam is admitted to the main valve via the gap between the two jaws of two moveable portions of a second sliding valve which is operated by the second eccentric attached to the crank-shaft. This eccentric is used to finely tune the valve timing of this model to obtain best running results of an engine. There are various methods used for reversing a steam engine. model compound steam engine, steam engine, model, crankshaft, valve, flywheel, wattle, engineer, eccentrics

Two black and white photographs of former Bendigo steam motor No. 2 at the David Mitchell estate railway, Lilydale district, photographed c1930. Reference Light railways 208, August 2009, page 9.Yields information about a former Bendigo steam motor.Black and White copy print contained within the Wal Jack Bendigo and Geelong Album, see Reg Item 5003 for more details. .1 - On rear in ink "Steam motor from the Bendigo steam tramway's (rebuilt). This was taken at the David Mitchell Estate at Lilydale used to run to the Mt Evelyn about 6 miles. Broken up after this photo was taken" Similar notes on rear of Ken Magor collections with the additional detail of photographer - Ray Pearson.trams, tramways, bendigo, steam trams, light railways, tram 2

7082a: - Induction fan discharge from the Stawell Gold MIne, this gunck would include the diesel fumes of trucks and mining machines. The steam Plume drifts over the nearby trees blackening and killing the. It also drifts over the reservior adding a touch of spice to the town's drinking water. site closed in 2001. Another fan is located near to Darlington Lane and McLennan Street.2 Photographs: 7082:Showing workmen drilling a shaft with a car in the background 7082a: Showing Steam? coming from the shaft.On Reverse: 7082 Mick Walsh 52 Patrick Street Phone 053 ******mining

Photograph of a Kettle Decatizing apparatus, as produced by H. Krantz Soehne (manufacturers of finishing machinery) of Aachen, Germany. It was sent to Arthur Heaton & Co. Ltd as part of a price quotation. Decatizing is the process of forcing steam through wool.Photograph, 1931, of a Kettle Decatizing apparatus, as produced by H. Krantz Soehne (manufacturers of finishing machinery) of Aachen, Germany. Decatizing is the process of forcing steam through wool.H. KRANTZ SOEHNE / AACHEN. 231.textile machinery textile finishing, h. krantz s?? arthur heaton and co. ltd, decatizing, textile machinery, textile finishing

Miniature biscuit tin used as a sample.Steam Biscuit Factorydomestic items, food storage & preservation

The steam train is pulling into the former Rupertswood Station. Guests who were invited to the Clarke family's mansion, 'Rupertswood Mansion' used Rupertswood Station after the servants had departed the train at Sunbury Station. This ensured that the servants arrived at the mansion and were able to arrange the luggage in the allotted rooms before the guests arrived. In later years students from Salesian College who needed to travel up the line from Sunbury used the siding, which was finally closed as buses transported the students.When William Clarke built Rupertswood Mansion in 1874, he also included his own railway station and a lodge at the main gates of the estate. He copied this practice from large estates in England.A black and white non-digital photograph of a passenger steam train arriving at a station with passengers waiting to board the train.rupertswood station, steam locomotives, rupertswood mansion, sunbury

No. 127 is a 2'-gauge ex-South African Railways 'NGG16' class Beyer-Garratt locomotive. It was built by Beyer Peacock & Co of Manchester (builder's No.7428 of 1951) to their "Beyer Garratt" patented design of articulated steam locomotive. The South African Railways Class NG G16 2-6-2+2-6-2 of 1937 is a narrow gauge steam locomotive. Between 1937 and 1968, the South African Railways placed 34 Class NG G16 Garratt articulated steam locomotives with a 2-6-2+2-6-2 Double Prairie type wheel arrangement in service on the Avontuur Railway and on the Natal narrow gauge lines - The third order was for a further seven locomotives in 1951, numbered in the range from NG125 to NG131, once again from Beyer, Peacock. These and the subsequent locomotives had welded water and coal bunkers and flat-topped water tanks with rounded top side edges. The Beyer, Peacock locomotives ordered by the SAR, numbers NG109 to NG116 and NG125 to NG131, were shared more or less equally between the Natal and Avontuur lines No. 127 was purchased from the South African Railways by the Emerald Tourist Railway Board for the Puffing Billy Railway in late 2011 / early 2012, together with a container load of spare parts stripped from a derelict NGG16, and prepared for transport to Australia. The spare parts will assist in the restoration of sister NGG16 No.129 in the short term, while No.127 will provide the PBR with the option of restoring a second NGG16 at some future stage, if required. details from http://www.australiansteam.com/BP7428.htmHistoric - Overseas - South African - Narrow Gauge Railways - Steam Locomotive Garratt Steam Locomotive - 2-6-2+2-6-2 Beyer Peacock & Co NGG16 No.127 build No.7428puffing billy, ngg16, sar, beyer peacock & co garratt ngg16 no.127 build no7428, narrow gauge, steam locomotive, garratt

An original newspaper cutting from The Illustrated London News 28 August 1852 regarding the steam-packet Great Britain leaving London for Port Phillip and Sydney.Realism, historical, etchings, newspaperAn original newspaper cutting from The Illustrated London News 02 April 1853 regarding the Royal Mail steam ship SS SYDNEY leaving London for Port Phillip and Sydney and its return journey.On the reverse - [NIL] iron-screw steam-ship, 1853, ss sydney, royal mail ship, port phillip, port jackson

The Outer Circle Railway was opened in stages in 1890 and 1891, as a steam-era suburban railway line. It traversed much of the modern City of Boroondara, including the suburbs of (from north to south) Kew East, Camberwell, Burwood, Ashburton, and Malvern East. At its longest, it ran from Fairfield station, on what is today the Hurstbridge line, to Oakleigh station, on the current Pakenham and Cranbourne lines.Steam train in a cutting on the Outer Circle Railway line. Exhibition enlargement donated by Stewart West from an original owned by Miss Foley.trains, outer circle railway

Steam Locomotive - 2-6-2 2-6-2 Beyer Peacock & Co Garratt NGG16 No.129 build No. 7430 Loco - Garratt NG129 Date acquired - 1996 Acquired from - South African Railways State when acquired - Work done - Currently being rebuilt to 2 ft 6 in (762 mm) gauge as a backup for G42. Expected Return to service in 2019. Restored to service - Current State - Currently being Rebuilt It was built by Beyer Peacock & Co of Manchester (builder's No.7430 of 1951) to their "Beyer Garratt" patented design of articulated steam locomotive. The South African Railways Class NG G16 2-6-2+2-6-2 of 1937 is a narrow gauge steam locomotive. Between 1937 and 1968, the South African Railways placed 34 Class NG G16 Garratt articulated steam locomotives with a 2-6-2+2-6-2 Double Prairie type wheel arrangement in service on the Avontuur Railway and on the Natal narrow gauge lines - The third order was for a further seven locomotives in 1951, numbered in the range from NG125 to NG131, once again from Beyer, Peacock. These and the subsequent locomotives had welded water and coal bunkers and flat-topped water tanks with rounded top side edges. The Beyer, Peacock locomotives ordered by the SAR, numbers NG109 to NG116 and NG125 to NG131, were shared more or less equally between the Natal and Avontuur lines Historic - Overseas - South African - Narrow Gauge Railways - Steam LocomotiveSteam Locomotive - 2-6-2+2-6-2 Beyer Peacock & Co Garratt NGG16 No.129 build No.7430 made of steel, wrought iron and ironpuffing billy, beyer peacock, beyer peacock & co garratt ngg16 no.129 build no.7430, narrow gauge, steam locomotive, garratt locomotive, garratt ng129, garratt ngg16 no.129

From the late 1920s several brands of irons, including Hotpoint and Light' N Easy were manufactured in Australia by the Australian General Electric Co. Ltd. Light' N Easy irons were marketed as a versatile iron, small and light enough to be taken with you if you needed to travel away from home.This iron is representative of electrical appliances developed under licence in Australia from the late 1920s onwards.Small yellow steam iron. There are controls and a water level indicator on the side of the iron. There are 25 steam vents in the base. Steam and dry iron with surge of steam. A 3 metre electrical cord is attached.Label: " General Electric Housewares Pty Ltd. Vic/ Nottinghill Melbourne 3166/ 700 Watts/ APP NO. V79008 Cat 04/06 240 Voltsdomestic appliances, light 'easy irons

SS Iberia was an ocean liner completed in 1954 for the Peninsular and Oriental Steam Navigation Company (P&O). Along withother liners, Iberia mainly provided passenger service between the United Kingdom and Australia. In the Annual Report 1954, Padre Oliver mentions: " Two fine new P & O ships made their maiden voyages during the year: "Arcadia" and "Iberia". In each case I was privileged to help to represent the Mission at the official luncheon."Marine artColour printed reproduction of a painting or lithograph print featuring 20th C passenger liner, hull and superstructure primarily painted white, under steam at sea. Small tug/fishing vessel in foreground. Larger steam ship on horizon. Print on plain board backing with plain mitred timber frame. Eyelet screws with wire.Printed signature lower right. 'JOHNSTON'iberia, passenger ship, p&o, marine painting, passenger ships, artwork-paintings, peninsular and oriental steam navigation company

Steam-driven traction engines had a variety of uses on farms before petrol and diesel power motors were developed. The one in the photograph is hauling a farm shed to a specific location.A non-digital black and white photograph of a steam-driven traction engine pulling hauling equipment and a small wooden building along an unmade track. A group of men are standing at the rear by the track supervising the shift. There are trees in the paddock.steam-driven traction engines, farms

12A Built in 1912 and painted Canadian red & dark brown, this locomotive was issued to the Colac to Crowes line, but over the years saw service on all four lines. It was withdrawn from service in 1954 at Moe and sent to Newport Workshops for storage where it remained until 1972. After overhaul at Ballarat North Workshops, it was brought to Belgrave in 1973 where it saw continuous service until withdrawn in 1982 for a complete rebuild. It was returned to service in 1992 in close to its early 1940s condition with all-over Black livery. It will be returned to its post WWI condition with low bunker, narrow ash chute, steel cowcatcher and Canadian red livery. Loco: 12A In service Monday, 23rd December 1912 Livery Canadian red & dark brown Owner Puffing Billy Gauge 762mm / 2' 6" Status Preserved - Operational Service History: Oct 1912 - Colac - initial allocation of a new locomotive Oct 1912 - Nov 1916 Colac Jan 1917 - Jan 1919 UFTG. Mar 1920 - Wangaratta Jul 1920 - Sep 1925 Colac Jan 1926 - Aug 1926 Moe Sep 1926 - Oct 1937 UFTG. Mar 1938 - Mar 1943 Moe Aug 1943 - Dec 1946 UFTG. Mar 1947 - May 1948 Workshops Mar 1949 - Apr 1950 UFTG. May 1950 - Aug 1954 Moe Oct 1954 - Jul 1970 Workshops Aug 1973 - In service at Puffing Billy Railway Victorian Railways - Narrow Gauge NA class steam locomotive number 12A Dates that 12A worked on the Gembrook Line Jan-1917 to Mar-1920 Sep-1926 to Mar-1938 Aug-1945 to Mar-1947 Mar-1949 to May-1950 Aug-1973 - Returned to service. Oct-1977 - Transferred to ETRB ownership.Steam Locomotive 12Apuffing billy, 12a, victorian railways, narrow gauge, steam locomotive, na class

The steam engine indicator, or dynamometer, is an instrument used on a steam engine (such as that of a vessel or train) to measure and record the change in the pressures of the engine’s cylinders during their operating cycle. The engineer would use it to identify problems or defects such as bad valve settings or constricted steam pipes. It could indicate the difference in efficiency caused by adjustments made to the engine, being able to instantly measure the variation of pressure from the engine stroke at any given time. This force of power would be registered by a pencil, fitted to the adjustable arm, which would trace a line on paper wound around the cylinder. The recorded information could be used in conjunction with mathematical tables. This particular instrument was made by T.S. Mc Innes, one of the better manufacturers of engine indicators. Mc Innes engine indicators were still being used in the mid 1900’s. This specific instrument was used by Mark Forsythe of North Berwial, Scotland and late of Ararat, Victoria when he was chief engineer on the “SS Talawena” in 1892. The Port of Warrnambool, in Victoria, harboured steam ships that carried both passengers and cargo along the south west coast in the late 1800’s and into the 1900’s. The engineer of a steam ship was responsible for reaching and maintaining the optimum level of steam energy to serve the locomotion and efficiency of the steam ship. The engineer would use a steam engine indicator to measure and record information to achieve this purpose. Engine Dynamometer or Steam Engine Indicator in square, fitted oak case. This brass instrument is used to measure and record steam pressure for setting up and adjusting valves on a steam engine. It has an oscillating recording drum with vertical, silver clip attached for holding paper in place around the drum. The drum oscillates left to right. There is a pulley attached to a length of cord, which is attached to the drum. Beside the drum is a fine metal arm, vertically adjustable, small hole in the end to hold a pencil. Inscription stamped into bracket of the arm. The engine indicator is mounted on a hinged side of the case that swings out ready for use. Attached chains prevent the side from opening past vertical. There is storage for other accessories and an empty compartment in the base (where a scale or ruler may have been located). The case has a collapsible wooden handle, brass hinges and two brass, hook-shaped catches. There is a code stamped inside the lid. It contains a brass, ‘T’ shaped steam-cock (or stop cock) with two open ends made of metal pipe with different sized threads. (Turning the handle on top opens and closes the space in the pipe and would close off the flow of steam from one end to the other.) Also inside the case are three different spiral springs, each with a threaded nut on the end that has a threaded hole inside it. Used by Mr Mark Forsythe when chief engineer on the SS Talawena in 1892 “T.S. MC INNES PATENT” and “522 _ _” (last 2 digits are unreadable) pressed into the arm of the brass indicator. “[ ] X ’ stamped inside the lid of the case. The 3 springs all have a number stamped into them: (1) “32” and “12” (2) “12” and “16” [above] “12” (3) “64” and “150” Card that came with instrument “This instrument was used by Mark Forsythe of North Berwial Scotland and late of Ararat, Victoria when chief engineer on the SS Talawena in 1892" dynamometer, steam engine indicator, t.s. mcinnes, glasgow, dobbie mcinnes, port of warrnambool, warrnambool, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, maritime museum, shipwreck coast, great ocean road

This is an oil painting of the Steam Tug Wattle after conversion to a passenger carrying vessel. She was a popular tourist outing for people in the Port Philip Bay area. This painting shows that Wattle was appreciated as a historic vessel, a fun mode of transportation and that there was some appeal to seeing images in her likeness such as this painting.Oil painting of the Steam Tug Wattle after conversion to a passenger-carrying vessel.The port side of the ship is shown in an open water landscape, and is moving towards the left hand edge of the frame The painting is signed in the bottom right hand corner " '98 David Carden"oil painting, passenger vessel, tourists, wattle, painting, bay steamers maritime museum, port phillip bay

This remote-controlled ship model was made by the blacksmith at Flagstaff Hill Maritime Village in the likeness of the Village's display passenger ferry, the S.S. Rowitta. SS ROWITTA: - The 1909 steam ferry, SS Rowitta, was installed as an exhibit at Flagstaff Hill in 1975 and was enjoyed by many visitors for 40 years. Rowitta was a timber steam ferry built in Hobart in 1909 using planks of Huon and Karri wood. She was a favourite of sightseeing passengers along Tasmania’s Tamar and Derwent rivers for 30 years. Rowitta was also known as Tarkarri and Sorrento and had worked as a coastal trading vessel between Devonport and Melbourne, and Melbourne Queenscliff and Sorrento. In 1974 Rowitta was purchased by Flagstaff Hilt to convert into a representation of the Speculant, a historic and locally significant sailing ship listed on the Victorian Heritage Database. (The Speculant was built in Scotland in 1895 and traded timber between the United Kingdom and Russia. Warrnambool’s P J McGennan & Co. then bought the vessel to trade pine timber from New Zealand to Victorian ports and cargo to Melbourne. She was the largest ship registered with Warrnambool as her home port, playing a key role in the early 1900s in the Port of Warrnambool. In 1911, on her way to Melbourne, she was wrecked near Cape Otway. None of the nine crew lost their lives.) The promised funds for converting Rowitta into the Speculant were no longer available, so she was restored back to her original configuration. She represented the importance of coastal traders to transport, trade and communication in Australian times before rail and motor vehicles. Sadly, in 2015 the time had come to demolish the Rowitta due to her excessive deterioration and the high cost of ongoing repairs. She had given over 100 years of service and pleasure to those who knew her. The remote-controlled model of the S.S. Rowitta is significant for its association with the Tasmanian early to mid-1900s passenger ferry, the wooden screw steamer Rowitta. It is is connected to the history of the Rowitta, that was a large exhibit on display at Flagstaff Hill Maritime Village from the museum’s early beginnings until the vessel’s end of life 40 years later. The display was used as an aid to maritime education. The Rowitta represents the importance of coastal traders to transport, trade and communication along the coast of Victoria, between states, and in Australia before rail and motor vehicles. The vessel was an example of a ferry built in the early 20th century that served many different roles over its lifetime of over 100 years. Model of the wooden steam ferry "S.S. Rowitta". This is a radio-controlled model built by the Flagstaff Hill blacksmith.flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, ship model, remote controlled steam ship model, s.s. rowitta, tarkarri, speculant, purdon & featherstone of hobart, passenger ferry 1909, tasmanian passenger ferry, vessel, charles street wharf launceston, sorrento, remote control boat, rowitta model, remote-controlled model

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.The "Flying Scotsman's" first run in Victoria. This photo was taken at the crew changeover in Longwood after the run from Albury. The Flying Scotsman Pacific 4-6-2, perhaps one of the most iconic steam locomotives in the world, visited Australia in 1988-89 for a series of events associated with the country’s Bicentennial Celebrations. This included the AusSteam 88 Steam Locomotive exhibition in Melbourne. At the top edge of the locomotive "SCOTSMAN" and on the lower edge of the locomotive "4472"railways wodonga, fred rochow, wodonga railwaymen, fireman noel strauss, driver len gregson, the flying scosman

Black and white photograph of steam roller and steam-tractor pulling church building along road.Written beneath photograph, "Church of England. Being shifted from cnr. Main St. and Pratt St. to Ringwood St. 1924."

This Steam Engine Coupling was recovered from the wreck of the Newfield and is thought to be part of a Donkey Engine (or steam donkey, or donkey winch), which is a small secondary steam engine with a cylindrical shaped boiler. In 19th century merchant sailing, a steam donkey was often used in marine applications such as to help raise and lower larger sails, loading and unloading cargo or for powering pumps. The barque Newfield left Liverpool on 1st June 1892 with a cargo of 1850 tons of fine rock salt for Brisbane. About six weeks later the ship ran into very heavy weather approaching the Australian coast. On 28th August at about 9pm her master, Captain George Scott, observed between the heavy squalls the Cape Otway light on the mainland of Victoria, but due apparently to a navigational error (the chronometers were incorrect), he mistook it for Cape Wickham on King Island, some 40 miles south. He altered course to the north expecting to run through the western entrance of Bass Strait, but instead, at about 1:30am, the ship ran aground about about 100 yards from shore, one mile east of Curdies River. The vessel struck heavily three times before grounding on an inner shoal with six feet of water in the holds. The Newfield remained upright on the reef with sails set for a considerable time as the wind slowly ripped the canvas to shreds and the sea battered the hull to pieces. Seventeen men survived the shipwreck but the captain and eight of his crew perished.Flagstaff Hill’s collection of artefacts from the Newfield is significant for its association with the shipwreck Newfield, which is listed on the Victorian Heritage Registry. The collection is significant because of the relationship between the objects. The Newfield collection is archaeologically significant as the remains of an international cargo ship. The Newfield collection is historically significant for representing aspects of Victoria’s shipping history and its association with the shipwreckCoupling is believed to be part of the Donkey winch's steam-engine. Threaded brass collar (with side outlet) attached to a copper pipe via a locking nut, and a four holed flange with bolts and coupling plate the other end.warrnambool, shipwrecked coast, flagstaff hill, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, shipwrecked artefact, 1892, 1893, 28 august 1892, 29 august 1892, barque, curdie's river, donkey engine, newfield, nineteenth century, peter ronald, peterborough, port campbell, shipwrecks, steam engine coupling, steam donkey, victorian shipwrecks

861 John Benn Locomotive - in active service - Emerald Station Built in 1886 by Société Anonyme Usines Métallurgiques du Hainaut - Locomotives Couillet for the West Melbourne site of the Metropolitan Gas Company, as a four-wheel tank locomotive similar to 986 and named “John Benn”. The West Melbourne gas works sourced its coal from Maitland, New South Wales, and the coal was brought by ship to a wharf adjacent to the West Melbourne gas plant. John Benn and Carbon were used to haul the coal over a 762 mm (2 ft 6 in) gauge railway from the wharf to the gasworks, a distance of about 450 metres (500 yards). It was withdrawn from service in the 1930s and stored until sold privately in 1962. It was rebuilt by its new owners in the style of an American locomotive of the 1880s and was used for some years at Walhalla. It currently has the name “J.C. Rees” and is used in active service for the 861 Footplate Experience. Wheels: 2-4-2ST Builder: Couillet Build Date: 1886 Construction No.: 861 Empty Weight: Unknown Weight on Drivers: Unknown Driver Diameter: Unknown Tractive Effort: Unknown Boiler Pressure: Unknown Cylinders: Unknown Fuel: Coal Gauge: 30 inchesHistoric - Industrial railways - Metropolitan Gas Company Ltd, Melbourne Steam LocomotiveDecauville Steam Locomotive 861 John Reespuffing billy, narrow gauge, industrial narrow gauge railway, metropolitan gas company, decauville 43, steam locomotive, john rees, john benn, 861 locomotive, couillet, 861

This whistle was mounted on H.V. McKay Store Building. It was used to indicate the factory's clock on / off times. The whistle could be heard throughout the district.Brass steam whistle

Menus used on P&O liners SS Himalaya and SS Arcadia 1955-56. After the Great war of 1914-18, Australia experienced what up until then had been its biggest surge in immigration from Europe. Australia was seen as the great land of opportunity and became one of the top places to migrate to, particularly from Britain. The increase in migration to Australia led Britain’s leading shipping line to the Far East, the Peninsular and Oriental Steam Navigation Company (P&O;), to invest in a fleet of new ships of around 20,000 tonnes each to handle the business coming their way.29 Cruise Ship Menus from P&O cruises 1955-56Peninsula & Oriental Steam Navigation Companycruise liners, migrants, menus, p&o

This little steam boiler has been beautifully built. It could have been used to drive an engine in a small workshop, a boat or launch, or even farming equipment. It is an example of the steam technology and mechanisation of the 19th century. William Cook introduced steam heating in England in the 18th century. Steam combined with pressure was used for powering transport, such as steam engines for trains, and manufacturing, such as steam engines driving manufacturing machines. Steam boilers are still used today as an energy-efficient means of power.This steam boiler would have been suitable to drive a small engine, possibly that of a small boat. Coal was added to the firebox for fuel to heat water in the boiler. It is an example of the power used to drive machinery and equipment in the mid-to-late 19th century. Steam boilers like this one have played a part in the evolution of steam power. Steam engine boiler; vertical cylindrical coal-fired boiler with a black firebox at its base and a dome top. The cylinder's sides and top have brass fittings, inlet and outlet taps. A round opening near the base is covered by an adjustable metal plate that controls the boiler's temperature. The front door of the firebox has two hinges at the base and when the side clips are opened. A shiny brass collar tops the tall chimney. Oak wood planks around the sides of the boiler, and held in place by brass bands with nut and screw fixtures. The boiler stands on a metal and wood frame with a looped handle at the back. An inscription has been noted. Circa 1880. "1948 D/430" flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, boiler, steam engine, steam boiler, coal fired boiler, vertical boiler, boat boiler, power source, steam driven, engine boiler, steam machine, firebox, steam engine boiler

Pallett and Wiseman operated out of "Coopers Timber Yard", Bridge St., Bendigo. They operated a steam chaff and corn crushing mill. They also supplied firewood, coal and coke.Sepia coloured photograph. Five men standing in front of a horse and cart. The cart is full of sacks of some produce. A building in the background with a sign on the top "Pallett & Wiseman steam chaff & corn crushing ma... Date and location unknown. Part of the Barker"s family collection.bendigo businesses, pallett & wiseman

0-6-2 Tank Locomotive No.1 "Delta" Gauge 2'0" Identification: 1 Delta Type: 0-6-2T Builder: Perry Engineering, Mile End, South Australia Builder's number: Perry 7967.50.4 of 1950 Building date: 1950 Current status - Static Exhibit Wheel Arrangement 0-6-2T Cylinders (Diameter X Stroke) 10 inches X 18 inches Boiler Pressure 180 psi Driving Wheel (Dia.) 28 ½ inches Weight 16 tons Coal Capacity 27 cubic feet Water Capacity 500 gallons The Perry Engineering Co, Mile End, South Australia built a total of 18 locomotives for the 2’0” gauge tramways used by the sugar industry in Queensland. This 0-6-2T locomotive was built by Perry Engineering Co. Ltd. of Mile End, Adelaide as their Builder's No. 7967.50.4 of 1950. It was used at Qanaba Mill, Bundaberg where it was known as No.1 "Delta". / Qanaba Mill No.1 No. 1 “DELTA” 0-6-2 TANK LOCOMOTIVE Gauge: 2 foot Built by Perry Engineering Company of South Australia in 1950 (Builder’s number 7967.50.4), “DELTA” is a medium sized Australian designed locomotive featuring Walschaert’s valve gear driving piston valves. Weighing 16 tons (16.3 tonnes) it was one of the post-war narrow gauge steam locomotives, which worked in the canefields of Queensland until 1978. “DELTA” worked at various sugar mills in the Bundaberg area and was finally withdrawn from service at Quanba Mill after a life of 28 years. Obtained by the Puffing Billy Preservation Society in 1981. Delivered to Australian Estates Co., Kalamia Mill named DELTA in 1950. Purchased by Fairymead Mill as No 20 DELTA. Purchased by Millaquin Sugar for Qanaba Mill as No. 1 DELTA, 1970 Withdrawn from service, 1978. Obtained by Puffing Billy Preservation Society for display at the Puffing Billy Museum.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used in Queensland in Sugar Mill service. Locomotive No.1 "Delta" - Steam Locomotive - made of steel, and wrought ironDelta0-6-2 tank locomotive no.1 "delta" perry engineering - puffing billy railway perry 7967.50.4 of 1950, puffing billy, qunaba sugar mill, bundaberg, perry engineering, delta, steam locomotive, 0-6-2 tank locomotive no.1