Showing 1380 items
matching weights
-
Flagstaff Hill Maritime Museum and Village
Equipment - Horse Harness, Early to mid-20th century
The early settlers of Victoria depended on horse drawn vehicles to farm, make roads and railways, deliver produce and transport people. Horse harnesses were an important requisite for all drivers and could be found wherever there were working horses. Horse Harnesses have played an essential role in different cultures throughout history. Simple, utilitarian horse harnesses made of leather straps and iron rings were being used in early China before AD 500 as well as ancient Greece and Rome allowing horses to pull chariots and ploughs. The Greeks and Romans were the first to use a "horse collar" which distributed the weight of the harness evenly across the horse's chest rather than relying on a "throat harness" that could damage a horse's throat or choke them. During the medieval period, European horse harnesses became more elaborate and decorative. Variations of different horse harnesses were also found in Native American and Middle Eastern cultures. Horse Harnesses usually have four basic components which include - 1. Communication - the bridle, bit and reins allows the driver to communicate instructions and commands to the horse, guiding its movement and direction. 2. Draft - the collar, hame straps, hames, traces and chains enables the horse to draw and pull the load efficiently by distributing the weight and transferring the pulling force to the vehicle. 3. Stopping - the breeching band, pole straps and breast strap helps to control or stabilise the horse and vehicle when moving downhill or stopping. 4. Support - the back pad, backband, belly band and back saddle keep the harness in the correct position and proper alignment. This dray harness is a plain, basic harness and reflects its working class origins. It was used by Mr. Oswald (Jack) Bourke with his horse and dray to firstly deliver drygoods from Sunbury to Melbourne in the 1930's and later (through the 1940's and 1950's up to 1961) when he worked on the garbage round for the Springvale City Council. This horse harness is a significant example of the equipment that was needed wherever horses were being used - particularly in the early years of Victoria's settlement by white settlers. Harnesses such as this example were used with drays, farming equipment, delivery carts and personal transportation.A leather and metal horse harness used with a horse and dray circa 1930's to the early 1960's. It is made up of a number of components. 1. A leather bridle with metal buckles and rings, blinkers and a metal single jointed, snaffle bit that has the initials M B stamped onto the leather. 2. A leather bridle with metal buckles and rings and a metal "straight bar" Eggbut snaffle bit. It has an elongated X design (with 4 dots) stamped onto the leather strap holders near each buckle. 3. A blue and white vinyl halter with one leather patched strap. The nose band and a chin strap are covered with woollen padding. 4. A pair of leather shaft protectors. They have lacing holes along each edge and a repeating design of small shapes (flowers, wings, crosses and arrowheads) which run along the front of each protector. 5. A leather strap with a stainless steel chain and catch and a maker's mark for "Glenn's Leather Goods, Pearcedale Victoria" stamped onto the end. 6. A wide leather strap covered with a webbing sleeve. It has two large metal rings and each end and one ring has a rope attached. 7. A leather strap comprised of three separate sections (two shorter and one longer) joined with two metal rings. The longer section has notches along its length and the shorter section at the other end has a buckle. It also had a maker's mark stamped on it but the mark is very worn and the writing is difficult to read. 8. An adjustable leather horse collar with two buckles and straps at the top opening and two "B's" stamped into the leather. The top of the collar is made from treated leather pieces stitched together and the underneath of the collar is untreated leather. It has a padded indentation running all the way around the collar for the hames to sit in. 9. Two pairs of long leather traces - each having a buckle and notched section at one end and each one is made with three lengths of leather spliced together. 10. A leather strap (with one spliced join) belonging to a horse harness with two shorter straps (each ending with a metal clip) attached to a steel D ring at one end. 11. Three assorted short leather straps - the top one has clips at each end and a buckle (for adjusting the length) in the centre, the middle strap has notches and a buckle and the bottom strap is white with notches and a buckle.Bridle with blinkers - "M B" Bridle - design showing an elongated X with a dot in each section stamped onto strap holder Shaft Protectors - stamped design of flowers, wings, crosses and arrowheads Strap with chain - "Glenn's leather goods / Pearcedale / Victoria" Leather Strap (with two metal rings) - Maker's stamp - "name indecipherable / SADDLER / ...OURNE" Collar - "B / B" Leather strap - flagstaff hill maritime museum and village, warrnambool, great ocean road, sunbury, springvale, dray, delivery dray, harness, horse harness, horse drawn vehicles, working horse, oswald (jack) bourke, bridle, horse collar, hames, shaft protectors -
Flagstaff Hill Maritime Museum and Village
Book - Technical Reference, Tables for Ascertaining The Strength of Spirits with a Sike's Hydrometer, c. 1922
The book was compiled for the proprietor, L Oertling (Ludwig Oertling), who established his firm of precision scientific instruments in 1849 and went on to become well-known in Britain for its manufacture of precision instruments, particularly its balance scales. In 1865 Ludwig Oertling and business partner Edward Wilds Laad at 27 Moorgate Street London were granted Patent 75 for the invention of improvements in hydrometers. The firm was situated at Turnmill Street, London, in 1922, when it advertised its products including hydrometers, petroleumeters, saccharometers, balances and weights, and automatic coin weighing machines in the British Industries Fair catalogue. In 1925 the firm became part of the Avery group of companies, which acquired Stanton Instruments in 1968 and about two years later Stantons merged into L. Oertling Ltd. Joseph Long has been mentioned by some sources as the author of this book, written for the proprietor of L. Oertling Ltd.The book has been recognised as being culturally important as a basis for our current civilization. It was of great importance to the Board of Revenue for the collectors of taxes and duties Customs Offices, and used in the calculation of alcohol levels in wine and spirits.Reference book, hardcover, burgundy with gold text and lines. Cloth cover with embossed design. Title: Tables for Ascertaining The Strength of Spirits for ascertaining the strengths of spirits with Sike's Hydrometer; Compiled for L. Oetlihg, by appointment, sole manufacturer of Hydrometers & Saccharometers to the Board of Inland Revenue. [some sources say the author is Joseph Long] Published in Turnmill Street, London, near Farringdon Street Station Printer: Printed in London, England by George Berridge and Co, Eastcheap Works, ECflagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, l. oertling, ludwig oertling., precision balances, edward wilds ladd, patent 75, improvements in hydrometers, hydrometer, automatic balance for weighing sovereigns, hydrometers, petroleometers, saccharometers, balances and weights, automatic coin-weighing machines, avery group, stanton instruments, l. oertling ltd, testing machine, tables for hydrometers, strength of spirits, alcohol content, alcohol measurement, board of revenue, joseph long -
Rye RSL Sub Branch
Cork helmet wolesley, Twentieth Century
This type of head dress was very commonly worn by British Commonwealth Forces in the Sub Continent and other tropical areas. This particular example would have been a common sight in Northern Australia during the time frame, as well as Africa, Middle East and the Pacific. It is a light weight ventilated helmet offering good air circulation via the vent in the top of the crown, and shade to the back of the neck. As well as protection by the peaked front for the eyes reducing glare, preventing sun and heat stroke. It also created an image of gentlemanly dress and pride in appearance. It conformed to an ideal and was considered quite fashionable and a little dashing, often worn at a jaunty angle, creating a rakish air, far from today's simplistic view of pure functionality and at as low as possible cost. Whether worn with a tropical uniform with jacket and trousers, or open necked shirt and shorts, the wearer was easily identifiable as British or one of the Commonwealth countries.WW2 RAAF Wolsley cork helmet. Helmet Khaki cotton six (6) panel outer, with three (3) fold pugaree. Colour patch on left side approximately 6cm X 5.5cm, Dark blue,2.5cm, Light blue, 0.5cm and Maroon 2.5cm. Tan leather trim around brim, tan leather chin strap. Traditional pith helmet four (4) hole domed type vent on top of crown. Beige leather sweat band pierced around the top and with a cotton cord adjustment threaded around. Fixed to shell in four points diagonally. Interior is also covered in Khaki cotton. Hand written in brown ink. A1917 F/Lt C KERR GRANTworld war two, head dress, helmet, pith, cork, cloth covered, leather trimmed, royal australian air force, officer, flight lieutenant, khaki, pith helmet, air force, tropical, hat -
Orbost & District Historical Society
textbooks, 1948 - 1982
These reference books were used in the Orbost pharmacy by various chemists. . Chemists who worked in Orbost included Henry Cottman; James Alfred Dubois Williams; Harry Arthur Murray; Miss P.E .Mason (Phyllis Estelle?); Miss Sybil Monica Buzza; Thomas James Frayer; Australia Shaw; James David Torley; John William Zimmer; Dalkeith William Steele; William Thomas Hollingsworth; E.E. Cohen; R.S. Anderson; Frances John Perry Faith Everard Pardew and Charles Anthony Wurf. "n Britain, the Medical Act of 1858 charged the General Medical Council with the "production of a book containing the list of medicines and compounds, and the manner of preparing them together with the true weights and measures by which they are to be mixed and prepared". The British Pharmacopoeia thus became the official reference book and superseded other previous manuals" (from .South Australian Medical Heritage Society Inc" These reference books have an association with Orbost. Historical works in pharmacy show the evolution of therapeutics and the development of diverse treatment and are therefore a useful research tool. Five heavy reference books. They contain detailed information on drugs and other pharmaceutical materials with standards for substances. Details of each book are in the catalogue folder.pharmacies-orbost reference-books-pharmacy medicine drugs -
Puffing Billy Railway
Vehicle - Aveling & Porter 11629, South Melbourne City Council Aveling & Porter 10 ton Steam Roller, 1923
Built by Aveling & Porter Ltd., Rochester, Kent, England Builder’s Number 11629 of 1923 Weight 10 Tons Used by the South Melbourne Council in road construction between 1926 and 1963 Aveling and Porter was a British agricultural engine and steam roller manufacturer. Thomas Aveling and Richard Thomas Porter entered into partnership in 1862, developed a steam engine three years later in 1865. The company became the largest manufacturer of steam rollers in the world. Service History : Title: City Surveyor's report Creator: Johnson, A.L Publisher: Prahran City Council Date: 1921 .... The 10-ton steam roller worked 302 days, the Aveling and Porter 12½-ton roller worked 211 days while the Garrett steam wagon continues to carry tar and road materials. city of prahran annual reports 1912-1913 http://www.stonnington.vic.gov.au/files/assets/public/history/city-of-prahran-annual-reports-1912-1913.pdf Industrial Steam Roller - Road Construction, South Melbourne, Victoria, Australia Aveling & Porter 10 ton Steam Roller with roof and rear tool box Builders Number 11629 Aveling & Portersouth melbourne, puffing billy, steam roller, aveling and porter, puffing billy museum, road construction, road steam -
Puffing Billy Railway
1 NT, Victorian Railways 2'6" Gauge Insulated Wagon, 1899
INSULATED wagon. Built in 1899 and numbered 1, it was the only one of its type built Service History : NTT In October 1899 a bogie insulated van was built and placed into traffic. In 1926, the class was relettered to NT. Obtained by the Puffing Billy Preservation Society By 1969, the vehicle was in the Menzies Creek Museum. Currently Located at Belgrave Station The NT is an insulated van. The wooden body (both sides and roof) was insulated with cowhair. It had two swinging doors either side in the middle, as have the NU vans. The van was painted white, in an attempt to reflect the summer heat. There was only one built for the narrow gauge lines. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1899 Number Built 1 In use none To be restored 1Historic - Victorian Railways - Narrow Gauge Rolling Stock - Insulated Wagon 1NT Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collectiontimber constructed body wall cavity filled with horse hair for insulation The NT is an insulated van. The wooden body (both sides and roof) was insulated with cowhair. It had two swinging doors either side in the middle, as have the NU vans. The van was painted white in an attempt to reflect the summer heat. There was only one built for the narrow gauge.1nt1nt, puffing billy, insulated van -
Puffing Billy Railway
51 NBH - Passenger Carriage - Excursion Car for wheelchairs, 1981
51 NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs Puffing Billy Service History or Notes Coupled Length 31 feet 4 inches (9550 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 2 inches (2794 mm) Weight 8 tons Capacity 24 passengers, or 20 passengers and 3 wheelchairs, or 16 passengers and 6 wheelchairs Number Built 2 In use 2 In 1981 the first of two extended NBHs with provision for wheelchair passengers (double door access and fold-up seats) was built, the second following in 1983. These were numbered 51 & 52 - a separate number series because of their length made them different from the other NBHs. May 2016 - In for repairs to the roofHistoric - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car specially built for Wheelchairs access51 NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs made of wrought iron and timber 51NBH -
Puffing Billy Railway
13 NUU - Louvred Truck, 15/ 7/1911
Van 13 NUU - Louvred Truck (11) Untrafficable - Menzies Creek Station Yard VR Service History 15/ 7/1911 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1898 - 1911 Number Built 14 In use 5 To be restored None *NUU 13.VA - 15/ 7/1911 NWS Built new - / /1926 - To NU 13.VA - NU 13.VA - / 6/1926 - Modified AC Malco /10/1954 CKT Sold (to) by Stores Branch to P.B.P.S. Purchased by Puffing Billy Preservation Society from Cockatoo for 20 pounds ($40.00). First complete railway truck owned by the Puffing Billy Preservation Society. Puffing Billy Service History or Notes Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered VanWooden Louvered Van - Made of Timber on a Wrought iron frame - current condition Untrafficable13 NUpuffing billy railway, pbr, rolling stock , 13 nuu, puffing billy, louvered van, 13 nuu - louvered van, victorian railways, 2'6" gauge, narrow gauge rolling stock -
City of Ballarat
Artwork, other - Public Artwork, Boer War Memorial by James White, 1906
The Boer War Memorial was created by sculptor James White in honour of Australian Soldiers who fought in the South African War (1899-1902). White used the electrolytic copper deposit method to produce this large statue, which is sometimes mistaken for a cast bronze work. The Foundation stone was laid on 18 May 1901 by H.R.H The Duke of York (George V). The sculpture was unveiled on the 1st November 1906 by His Excellency Baron Northcote G.C.I.E., C.B. Governor General of Australia and then Mayor of Ballarat, J. J. Brokenshire. Bravery and mateship are beautifully captured in depiction of a scene taken straight from the battlegrounds. Today the memorial is a much-photographed tribute and exploration of the friendships and struggles of men at war. A proud cavalry horse bears the weight of two men in the chaos of the battlefield. The Boer War in Africa was an early example of the Australian Colonies sacrificing men and equipment for Britain to defend it’s Empire against colonial insurgence. The memorial is of historical and aesthetic significance to the people of Ballarat.Horse and figures, bronze mounted on bluestone base and granite plinth, plaques list the war dead. The artwork depicts two soldiers and a horse. A British soldier is being succoured by an Australian mounted rifleman. In honour of Australian Soldiers who fought in South Africa 1899-1902. Foundation stone laid 18th May 1901 by H.R.H The Duke of York (George V). Unveiled 1st November 1906 by His Excellency Baron Northcote G.C.I.E., C.B. Governor General of Australia. J. H. Barker Chairman. J. J. Brokenshire Mayorboer war, south africa monument -
Ballarat Tramway Museum
Ephemera - Weekly ticket, Block of SECV 3/- weekly tickets
Each ticket medium weight card, on pink card and printed on black ink to give day numbers, monthly, week number, transfers and day of the week, excluding Sunday. Numbered on the right end of the ticket. Static number (1 - 7) on the left may be to indicate the day of the issue. On the rear of the ticket are the details of the ticket use, allowing passengers one return journey between City and section 3 or 4. Not available on Sundays. Form Number TYE 3-13 Note: 1. See Reg. Item 230 on page dated Feb. 22 for another two weekly tickets, c1950, price 2/6 - similar to these, but used. Page 38 of Ballarat Tramways has a photo of the 2/6 weekly ticket, with a note, used about 1950's. See also Reg. item 2102, 2103, 2104 and 2105. Not known when these tickets used, possibly c1950'sDemonstrates a SEC Weekly ticket.Block of SECV 3/- weekly tickets, ticket numbers B 37969 - 37979. Originally printed and stapled into a blocks of 20 tickets. tickets, weekly tickets, tramways, trams -
Geoffrey Kaye Museum of Anaesthetic History
Label, Cylinder
Large unused diamond shaped Austox label made for use on ethylene cylinders. Beige with red lettering.Information printed on label: SPECIALLY PREPARED FOR MEDICAL USE / AUSTOX [logo] / INFLAMMABLE / ETHYLENE / KEEP COOL / Product of the OHIO CHEMICAL & MFG. CO., CLEVELAND. / Contents...............c.ft. ............... gallons (Imp.) / Weight of Full Cylinder ..........lbs. ..........ozs. / 31 OUNCES ETHYLENE = 166 1/2 GALLONS (IMPERIAL) / Use only moderate force when closing valve / Always test with water for leakage after using / Australian Oxygen & Industrial Gases / Pty. Ltd. / MELBOURNElabel, cylinder, cig, ethylene, austox, ohio chemical and mfg company, australian oxygen and industrial gases pty ltd, commonwealth industrial gases ltd -
Clunes Museum
Container - TIN
Yellow Temple Bar Tobacco tinTop of Lid: Temple Bar/Fine Cut Tobacco Manufactured by the British Australian Tobacco Co. Pty.Ltd./Melbourne, Australia Side of Lid: Temple Bar Fine Cut/1oz. Net Weight when packed Inside Lid: Notice/Every tin of genuine Temple Bar Tobacco has the words Temple Bar tobacco & the name of the manufacturing company appears on the band or wrapper with which the tine sealed. The British Australian tobacco. Pty.Ltd., Melbourne "None genuine without the band or wrapper"containers, tins -
Bendigo Historical Society Inc.
Accessory - BADGE COLLECTION: SECV PROVINCIAL TRAMWAYS PASSES, UK
Object. Round tobacco tin made of gold coloured metal. Lin has concentric circles of gold and green with black cetic section. Written on lid ""De Luxe Dr PAT TOBACCO 2 oz net weight. Black Dymo Label -''Tram Pass''. Tin of twenty one round metal tokens with enamelled front. Concentric circles from edge of blue enamel and white enamel. Suspension piece at crest. Centre section of gold coloured enamel with red shield in centre with gold coloured Southern Cross. Hand above shield holding a stick. On outer blue enamel. "SUPPLY DEPARTMENT PROVINCIAL TRAMWAYS'', On white inner enamel ring ''STATE ELECTRICITY COMMISSION OF VICTORIA''.Imprinted on reverse, Various 3 digit numbers - different on each token.numismatics, tokens, secv provincial tram passes -
City of Greater Bendigo - Civic Collection
Book - Cookbook, Golden City Recipes, 1963
This cookbook was compiled by the Neale Street North Pre School Mothers' Club Committee with the forward written by Anne Galvin O.B.E, President of the Bendigo & District Pre-school Association. Anne Galvin was one of Bendigo's best known charity workers and she used her first speech as Mayoress (1944) to indicate her intentions to assist mothers and children. This recipe book includes contributions by the Mayoress of the day (Mayoress Rae), Television Hostesses Corinne Kirby and Ruth Nye and Mrs Bolte and Lady Brooks. Illustrator of front cover unknown.Bound and printed cookbook containing one hundred and eight pages of recipes and advertisements including forward written by Anne E. Galvin. Colour cover, stapled on left hand side. Advertisements for local businesses include Gordon H. Hall Beauty Salon, Gas and Fuel Corporation, Hesse Bros. Electrical and Sandhurst Milk & Cream, Recipe categories include: By Special Request; Soups; Sea Foods; Meat and Poulty (sic) Dishes; Hot Sweets and Puddings; Cold Sweets; Meals in a Hurry; Salads and Dressings; Savouries and Fillings, Icings, etc; Cakes Large and Small, Biscuits; Scones, Buns and Loaves; Jams, Pickles and Preserves; Gravies and Sauces; Confectionery; Weights and Measures; Index to Advertisers; Beauty Hints. city of greater bendigo education, city of bendigo mayoress, mayoress galvin, mayoress rae, cambridge press, mayor w cambridge, anne galven -
Ballarat Tramway Museum
Document - Photocopy, Drawing of ESCo Ballarat Tramways, c1990
Photocopy of a drawing prepared by Dave Macartney in the mid 1980's of the track layout of the Electric Supply Co. of Victoria's Ballarat Tramway system, excluding the single track to Sebastopol. Plan shows the location of the loops, loop type, street names, position of replacement loops installed by the SEC during the reconstruction, depot layout, powerhouse siding and railway in Lydiard St. North. Prepared from inspecting the Plans of Ballarat services drawings in the Ballarat Water Board's Offices. Drawn on the back of old import forms of a light weight paper and has shown through the printing underneath. Titled "Ballarat Tramways Company Days 1905 - 1930" Number of small differences to the map drawn for Keith Kings, "The Ballarat Tramways" book, page 22.trams, tramways, ballarat, esco, track layout, map -
Bendigo Military Museum
Photograph - Photographic Technicians operating the KLIMSCH Camera at the Army Survey Regiment, Fortuna, c1980s
These four photographs were most likely taken in the mid-1980s in Lithographic Squadron at the Army Survey Regiment, Fortuna, Bendigo. The equipment operated by the technicians is the KLIMSCH camera. The main tasks undertaken by the technicians were most likely enlargements and reductions of map reproduction material. The KLIMSCH Commodore camera was introduced in 1953 and was the largest in the Southern Hemisphere. It was replaced with a new model of the same size in 1979. The new model with its computer-based interface provided productivity gains with improved speed and its consistent results led to less wastage in time and materials. Its variomat lens system provided improved retention of map feature linear weights during the camera reduction process. The camera which was specially made for the Army in Germany was fully automatic and power operated. It was claimed to be one of the biggest automatic cameras of its type in the world. It was made to the specifications of the Royal Australian Army Survey Corps to assist in the production of the very high standard maps for the Army. This is a set of four photographs of technicians operating the KLIMSCH Camera at the Army Headquarters Survey Regiment, Bendigo c1985. The photographs were on 35mm negative film and scanned at 96 dpi. They are part of the Army Survey Regiment’s Collection. .1) Photo, black & white, c1985, Frank Lenane operating the KLIMSCH Camera. .2) - Photo, black & white, c1985, KLIMSCH Camera. .3) to .4) - Photo, black & white, c1985, John Whaling operating the KLIMSCH Camera..1P to .4P – no annotationroyal australian survey corps, rasvy, army survey regiment, army svy regt, fortuna, asr, litho -
Federation University Historical Collection
Document - Document - Design, E J Barker: University of Melbourne: Bachelor of Mechanical Engineering; Civil Engineering 1 and 1A; Design of Welded Plate Girder, 1946
Assessment No 2 Project was to design a welded plate girder required in a building to span between two steel columns which have to be spaced 60 feet centre to centre. It needs to carry its own weight plus specified loads. This was part of Civil Engineering 1A . Jack chose to do Engineering while still at Footscray Technical School as it gave access to Diploma Courses and tertiary studies. This enabled him to enter the University of Melbourne and do a Bachelor in Mechanical Engineering - 1945, 1946, and 1947. In 1948 he did a Diploma in Education at Melbourne University. From this path he was able to follow a career in teaching and his first appointment was at the School of Mines in Ballarat, (SMB) 1949. He became the first Vice Principal of SMB in 1960 and then Principal in 1964 to 1976. From 1976 to his retirement in 1987, he was the Foundation Director of Ballarat College of Advanced Education (BCAE). The Library building at Mount Helen Campus is named after him.Manila folder with design assessment. Written descriptions and detailed drawings.e j barker, jack barker, melbourne university, engineering, diploma of mechanical engineering, diploma of electrical engineering, school of mines ballarat, smb, diploma in education, vice principal, principal, foundation director, ballarat college of advanced education, bcae, bachelor of mechanical engineering, library, mount helen campus, engineering drawing, design, specifications, manufacture, civil engineering, welded plate girder, 60 feet, steel columns -
Kiewa Valley Historical Society
Belt Linesman Pole, circa mid to late 1900's
This linesman belt was used under the 1947 Electricity Regulations and before tighter Occupation and Health regulations (late 1990's early 2000's) were introduced that mechanical lifting platforms(wherever possible) replaced the belt up the pole method.The safety concern was that it required that tools needed by the linesman had to be placed in a large canvas bag and attached to the belt (extra weight) then the linesman had to climb the ladder. Ladders had to be at the correct angle and not able to "slip" from their initial footings. A full harness and a secondary fall belt is now mandatory for pole linesmen. The safety of fellow workers could be compromised if they were required to assist or recover the first linesman if needed. In 2006 an additional 269 registered lineworkers were employed. Please note that the terminology of linesman has become unisex. The linesman's belt enabled the linesman to place his feet against the pole adjust the belt (if needed) and lean back securely allowing both hands to be free to work with. This linesman belt is very significant to the Kiewa Valley due to the numerous poles and high voltage overhead power structures that needed maintenance for the extensive "mushroom" installation of electrical power polls(wood and metal). On high poles (steel) climbing pegs were welded on, however in the Alpine areas snow in winter caused an OH&S problem which were hard to overcome. The safety of a linesman when maintenance of electricity line on poles can be highlighted by the New Zealand linesman who survived an 11,000 volt shock when carrying out maintenance. For the record 11,000 volts is four times more powerful than execution by "the electric chair". The maintenance of the linesman's belt was his responsibility (keeping it clean and in "good" condition). Labour laws change this initial responsibility, from the linesman, to the employer. Climbing pegs were installed on higher poles that extended beyond the reach of ladders.This thick leather linesman belt is made from two lengths of heavy lengths of leather straps sewn together to make up 80% of the belt. The remaining 20% is "the belt tonge" which has eleven holes for three (solid steel tang) buckle connections.kiewa hydro electricity scheme, victorian state electricity commission, relays, generators, electrical pole maintenance -
Flagstaff Hill Maritime Museum and Village
Container - Collar Box, Rexbilt Leather Company, 1924-1930
The evolution of the stiff shirt collar occurred in the 1830s when the detachable collar was "invented." At this time, the detachable collars were simply normal shirt collars like you’d see today, but sold separately from the shirt itself and needed to be kept in a container to keep them clean and accessible. The detachable collars were a way to avoid the weekly laundry. Because collars and cuffs were both the most visible parts of shirts and the parts most likely to get dirty, separating them allowed people to do the shirt equivalent of only washing your armpits after you go to the gym. That meant that the main body of the shirt could remain soft while the collar and cuffs that were visible could be starched and shaped. The popularity of detachable collars and starched collars, in general, began to fade in the 1920s and 30s. As shirt styles began to change. The advent of central heating, lighter weight fabrics, and a more relaxed social attitude to fashion all contributed to making men’s clothes more comfortable and less formal.An item that was used to store detachable men’s shirt collars from the early 20th century at a time when men's fashion was more formal and how a person dressed especially for formal occasions dictated a person's social standing. The subject item comes from a time that gives a snapshot into the past at the social norms of the time.Collar box, leather, cylindrical, includes strap, buckle, stitching and cardboard lining and man's white collarCollar inside box marked "CF652 Rexbilt Size 16 1/2 x 1 3/4" flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, collar box, men's collar box, men's collar, leather collar box -
Ballarat Tramway Museum
Ephemera - Ticket, Block of SEC 1/6 weekly tickets
Each ticket medium weight card, on manila coloured (210gsm) card and printed on black ink to give day numbers, monthly, week number, transfers and day of week, excluding Sunday. Numbered on right end of ticket. Static number (1 - 7) on left indicate it may be the day of issue. Each ticket has been stamped "CANCELLED" On the rear of the ticket is the details of the ticket use, allowing the passenger one return journey between City and section 2-3 or 3, or between 2-3 and 4. Not available on Sundays. Form Number TYE 2-12. Note: See Reg. Item 230 on the page dated Feb. 22 for another two weekly tickets, c1950, price 2/6. Printed in off-white card in red ink. Available for travel between city and section 3 or 4. See also Reg. Item 2103, 2104, 2105, and 2106. Not known when these tickets were used, possibly before the 1950's.Demonstrates a SEC Weekly ticket.Block of SEC 1/6 weekly tickets, ticket numbers A124165 to A124179. Printed and stapled into a blocks of 20 tickets. trams, tramways, tickets, weekly tickets -
Ballarat Tramway Museum
Ephemera - Ticket, Block of SEC 2/- weekly tickets
Each ticket medium weight card, on 210gsm manila coloured card and printed on black ink to give day numbers, monthly, week number, transfers and day of week, excluding Sunday. Numbered on right end of ticket. Stapled with heavy brown cardboard backing strip. Static number (1 - 7) on left indicate it may be the day of issue. On rear of ticket is the details of the ticket use, allowed passenger one return journey between City and section r 3, or between 3 and 6. Not available on Sundays. Form Number TYE 3-11. Note: 1. See Reg. Item 230 on the page dated Feb. 22 for another two weekly tickets, c1950, price 2/6. Printed in off white card in red ink. Available for travel between city and section 3 or 4. See also Reg. item 2102, 2104, 2105 and 2106 Not known when these tickets used, possibly prior to 1950's.Demonstrates SEC Weekly tickets.Block of SEC 2/- weekly tickets, ticket numbers B 89023 - 89039. Printed and stapled into a blocks of 20 tickets. trams, tramways, tickets, weekly tickets -
Ballarat Tramway Museum
Document - List, "Numbers and Particulars of Trams" - Ballarat, 28/9/1970
List titled "Numbers and Particulars of Trams", dated 28/9/1970, split into separate sheets for single truck and bogie trams which includes the Scrubber tram. Tram 20 has been deleted following its demolition on 17/9/1970 (see item 1088). Gives details of where purchased from, date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheelbase, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons. Has a list of abbreviations on the base of each sheet. See also 8721 and 8722 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Typed List of tramcars and their details for Ballarat - carbon copy two double foolscap sheets.tramcars, ballarat, equipment, lists, data -
National Wool Museum
Book - Notebook, Collins Textile Diary - 1958, 1958
Nino Corda was a Geelong based textile designer who worked at various textile mills between 1957 & 2003. He travelled the world in search of the latest fashions and techniques and developed timeless designs that were much loved by Australians. These items are on rotational display at the National Wool Museum’s ‘In the Factory’ exhibition. For many years, Nino also worked as part of the Honorary Staff of the National Wool Museum. His passion for the world of textiles provided energy and knowledge to the visitors and staff of the museum. Although Nino has now retired from his honorary position and has hung up his Australian Tartan vest, these items will continue to serve the community in sharing the stories of Australian Textile design. This notebook contains information on how to calculate and enlarge a small sample pattern into a larger textile. The equations would provide answers to the required length of thread (often measured in weight as opposed to distance) of a selected textile. The sample and appropriate thread would be needed for mass production at a commercial mill.Blue textured vinyl forms the covers of this notebook. On the front of the inscription is visible in gold text. Internally, small font black writing on yellowing pages forms most of this notebook. Pp.128 published pages with calendar and spare pages for notes forming the second half of this notebook. Front Cover. Words, printed. WITH THE COMPLIMENTS OF / NOEL P. HUNT & CO. PTY. LTD.textile design, textile calculations -
Vision Australia
Functional object - Object, Cane basket on wheels
Basket weaving and brush making was a source of income for those who worked in the workshops at RVIB and other institutions in New South Wales and Queensland. A diverse range products could be produced with cane, such as cane chairs, cots, washing baskets and trolleys, and the Institution sought to highlight these in the annual report. Over time the demand for, and supply of, cane changed - particularly during World War 2 when Asian sources were under attack or destroyed. At home, other materials such as plastics as well as the ability to import cheaper pre-produced products further reduced the demand for workshop pieces. This cane basket was used at QBIC for transporting heavy items. The side has been reinforced with wood and four metal bands to help the cane keep it's shape and take the weight of heavy items. The base has two pieces of board and rotating wheels are attached to the middle of the lower board which allows it to sit above ground level and be wheeled over flat surfaces. A rope handle is attached to two sides as well.1 deep cane basket with two wheelsQBIC Industries - Asset Number: 1430-1 Description: Push Trolley 7 Location: 18R Block Cane Shop employment, qbic industries -
Trafalgar Holden Museum
Vehicle - Holden model FB sedan, 1960 - 1961
The FB was promoted as being longer, lower, more spacious and more powerful than the FC model, but in reality it was only slightly so on each count overerall length was 5.5 inches (140 mm) greater, although the wheelbase remained the same. The engine bore was still 3 inches (76 mm), the last model with that specification. Engine capacity was 138 cubic inches (2.16 L) but the compression ratio was raised. However, the resulting extra 4 brake horsepower (3 kW) of power did not compensate for the greater weight of the FB, so performance was inferior to that of its predecessor. Changes were also made to the brakes, front coil springs, air cleaner and clutch. Obvious styling differences were the lower bonnet, finned rear mudguards with new taillights (on the sedans and wagons only) and a wrap-around windscreen. Seating was improved, as was the instrument panel. A refinement of the FC model but appearance significantly changed with a wraparound windscreen, lower bonnet and finned rear guards.. This vehicle was purchased in NSW The interior was in excellent condition bur required extensive exterior work to bring it back to its original condition, It had a mileage of 8500. A refinement of the FC model but appearance significantly changed with a wraparound windscreen, lower bonnet and finned rear guards. It was the first Holden with acrylic paintwork.Two tone grey body , four door FB Holden sedan. Finned rear mudguard,. Holden Special Registered number 63452-Hholden, automobile, 1960, car -
Orbost & District Historical Society
rabbit traps, First half 20th century
During the Great Depression from 1929 to 1932, rabbit trapping was a means of survival for many people. Rabbits provided meat and pelts which were sold for making felt hats such as the Akubra. Rabbit populations are controlled in the 21st century by poisoning, destroying or 'ripping' burrows (warrens), biological control with rabbit haemorrhagic disease and myxomatosis, and by shooting. Rabbit-proof fences also prevent the spread of rabbits into some areas. (ref. Powerhouse Museum) Steel-jawed rabbit traps were widely used in urban and rural Australia from 1880 to 1980. This trap is symbolic of the battle that Australians have waged against burgeoning rabbit populations for over a century. Rabbits cause enormous damage to Australian soils and biodiversity. The introduction of rabbits to this country was an environmental disaster.Two iron rabbit traps. Each consists of a pair of jaws held closed by spring tension and a triggering mechanism. When the trap is triggered the jaws close over the top of the bridge, plate and tongue mechanism that is designed to trigger the trap. A chain is attached by a hook on the bent end of the trap's spring with a long steel spike looped over the last link of the other end of the chain. The trap is designed so that the metal jaws snap shut against each other when the trap is activated by the application of weight to the pressure plate. In use, traps are set with open jaws, buried lightly just below the surface of the earth. When an animal steps on the pressure plate, the jagged teeth of the jaws snap around the animal's leg, usually breaking bone and sinew. Thus the animal is immobilised.rabbits rural trapping -
Orbost & District Historical Society
rabbit trap, first half 20th century
During the Great Depression from 1929 to 1932, rabbit trapping was a means of survival for many people. Rabbits provided meat and pelts which were sold for making felt hats such as the Akubra. Rabbit populations are controlled in the 21st century by poisoning, destroying or 'ripping' burrows (warrens), biological control with rabbit haemorrhagic disease and myxomatosis, and by shooting. Rabbit-proof fences also prevent the spread of rabbits into some areas. (ref. Powerhouse Museum) This trap was used in the Orbost district. Steel-jawed rabbit traps were widely used in urban and rural Australia from 1880 to 1980. This trap is symbolic of the battle that Australians have waged against burgeoning rabbit populations for over a century. Rabbits cause enormous damage to Australian soils and biodiversity. The introduction of rabbits to this country was an environmental disaster.A rusted iron rabbit trap which consists of a pair of jaws held closed by spring tension and a triggering mechanism. When the trap is triggered the jaws close over the top of the bridge, plate and tongue mechanism that is designed to trigger the trap. A chain is attached by a hook on the bent end of the trap's spring with a long steel spike looped over the last link of the other end of the chain. The trap is designed so that the metal jaws snap shut against each other when the trap is activated by the application of weight to the pressure plate. In use, traps are set with open jaws, buried lightly just below the surface of the earth. When an animal steps on the pressure plate, the jagged teeth of the jaws snap around the animal's leg, usually breaking bone and sinew. Thus the animal is immobilised. rabbit-trap rural -
Flagstaff Hill Maritime Museum and Village
Weapon - Cannon, 1813
This 1813 cannon is classified as a carronade, having been made by the Carron Ironworks foundry in Stirling, Scotland in 1813. It is a large calibre, short range, gun mainly used on ships. The carronade model of cannon was first used when introduced into the British Royal Navy in the American War of the Revolution (1775-1883). This cannon was originally a 28pdr, 48cwt, 8ft gun. The date ‘1837’ on the barrel probably indicates the date that the Board of Ordinance accepted the change in size to a 32pdr. It may originally have been a naval gun and the conversion undertaken when it was brought ashore. It is very probably one of the 15 guns that are known to have constituted the defences of Victoria in 1860. This group of 32pdrs was the shorter model of the 4800width and 8ft length cannon and as such are different from the 32pdrs found in NSW. It was originally located on Cannon Hill in Warrnambool when it was the site of the Warrnambool Battery Western Artillery, formed in 1866. It was obsolete by the time of the 1887 fortifications, and was moved from the Warrnambool Fortifications to the Botanic Gardens in 1910, when the Fortifications were declared obsolete. HISTORIC INFORMATION ABOUT THE CANNON IN THE WARRNAMBOOL AREA In the years following the Crimean War (1854-1857J) there was a great concern in the Colony that Imperial Russia would attempt an invasion. Coastal defences in the colony of Victoria were greatly strengthened by the Government as a result. Warrnambool was originally protected by cannons at Cannon Hill, approximately 1 kilometer west of the Flagstaff Hill Fortifications. The cannons included two 1866 guns, both 80 Pound Rifled Muzzle Loaders (RML) purchased by Victoria’s Colonial Government. They were part of a shipment of 26 such guns sent from England in December 1866. They are registered as No. 23 (80cwt-2qr-0lbs) - Gun 1, and No.13 (81cwt-1qr-12lbs) - Gun 2. They were cast at the Royal Gun Factory, Woolwich Arsenal, in 1866 and have a 6.3 inch bore. Both barrels carry the Royal Cypher of Queen Victoria, Insignia of the Royal Engineers, within the Garter and Motto surmounted by the Crown, with the Royal Cypher of Queen Victoria within the Garter (letters in centre “VR”, motto “HONI SOIT QUI MAL Y PENSE”, "Shame be to him who thinks evil of it."). The guns were originally supplied with wooden carriages. (The Royal Arsenal at Woolwich, England, was established eleven years after the Restoration of King Charles II. It was the principal supplier of armaments to the British and Empire Governments. At the height of its operations during World War One the factory covered 1300 acres and employed very nearly 80,000 workers. Woolwich was the Headquarters of the Royal Artillery since the raising of that Regiment in 1716. The Arsenal was closed in the late 1960’s.) The two 80pdr cannons were transferred to the Warrnambool Garrison Artillery Battery Fortifications erected at Flagstaff Hill in 1887 as part of Victoria’s Coastal Defences. The original wooden carriages were subsequently replaced with the present iron garrison carriages in 1888. They are a “C” pivot. The ‘racers’ or curved track set into the floor of the gun emplacement (which enabled the guns to be traversed more quickly) are as specified for guns up to 10 inch, being of wrought iron 2.78 inches wide. A temporary third gun, now no longer on Flagstaff Hill’s site, was a 5 inch Rifled Breech Loading (BL) Armstrong gun mounted on an Elswick hydro pneumatic disappearing carriage It was faster to load and fire than the 80 pound RMLs and its arrival spelt the end of the older 80 pound guns’ useful life, apart from being used for practice sessions. The 5 inch BL gun was the main defensive weapon of the Warrnambool Battery until the Battery was downgraded in importance and the gun was recalled to Melbourne in 1910. The gun emplacement still remains in place set between the 2 80pdr cannon. The State of Victoria took over the ownership of the guns at the time of Australian Federation in 1901. In about 1901/1902 the Garrison Battery was converted to the Warrnambool Battery of the Australian Field Artillery (No 4 Field Battery). It was equipped with 4.7 inch naval guns mounted on field carriages. They were now a mobile unit but continued to use the Warrnambool Garrison area at Flagstaff Hill for practice. When the Fortifications were declared obsolete the two 80 Pounder RML were relocated to Cannon Hill in 1910. On the outbreak of World War 1 the 4.7 inch guns were recalled to Melbourne, and the Battery was disbanded. Most of the personnel probably re-enlisted in the local 4th Australian Light Horse Regiment. The two 80 Pounder RML were moved back to the Fortifications in 1973. They were both fully restored by Army First Year Apprentices at the Ordinance Factory in Bendigo in time for the centenary year of the fortifications in 1987. The guns are capable of firing 80 pound (32.3kg) armour piercing exploding shells 3.65kms out to sea. They were original manned by volunteers before a paid Garrison was established. Now the Guns are again fired by volunteers on Special Event days. Since restoration the Gun Number 1 had been fired on a regular basis but Gun Number 2 hadn’t been fired since the mid 1990’s. In April 2015 Gun Number 2 was serviced in preparation for the firing of both cannons on the ANZAC Centenary commemorations on April 25th 2015. Other guns from the original Cannon Hill location were obsolete by the time the 1887 Warrnambool Garrison Artillery Battery was built. These guns are (1) a 32 Pounder Muzzle Loading Smooth Bore (SB) cast in 1813 at the famous Carron Foundry, number 80837 and now located in the Warrnambool Botanic Gardens. It is now mounted on a replica carriage due to the original carriage being in a fragile condition (the original carriage stored under cover at Flagstaff Hill). (2) a 68 Pounder Muzzle Loading Smooth Bore cast in 1861 at the equally august Low Moor Foundry, number 10310 and now located on the lawn area at the entrance to Flagstaff Hill Maritime Village. It is still mounted on its original wooden garrison carriage. Its wooden slide compressor mechanism is fragile and now kept in Flagstaff Hill’s storage. There are only seven 32 Pounder SB made by Carron and fifteen 68 Pounder SB made at Low Moor known to exist in the State of Victoria Plaque attached to the carriage “This replica carriage was constructed by the Warrnambool Tritan Woodworkers club in conjunction with the generosity of local businesses and the Warrnambool community. The original carriage (circa 1860) was removed for restoration and is now located at Flagstaff Hill Maritime Village. The timber used for the replica carriage is Monterey Cypress, which was an early planting in the gardens. 2010 marked the centenary of the cannon’s relocation in the Warrnambool Botanic Gardens.” (Reference; Victorian Guns and Cannons, South Western Victoria Assessment, May 2008, item W/B/01; Flagstaff Hill Maritime Village datasheets and archives). There are only seven 32 Pounder SB made by Carron known to exist in the State of Victoria and this is one of them. On a world level, this cannon represents a high level of rarity. Further, as it has been modified (bored up) it is representative of the historical process of amending artillery in order to ensure a longer usefulness of each piece despite rapidly advancing artillery technology. The number of surviving carriages with traversing slides in this group in South Western Victoria is unique in Australia and probably in the World. Out of 10 such platforms surviving in Australia, the South Western Victorian group has half. Several survive around the world but probably not in such a large group. The wooden sliding compressor mechanism belonging to this cannon is extremely rare, and the only one in this South Western Victorian group of Guns and Cannons. As a whole, this cannon has undergone very little restoration or modification, giving it a high level of integrity. The City of Warrnambool is one of several custodians of a collection of artillery pieces of heritage significance at a state, national and international level. These pieces are directly related to the defence of south-west Victoria in the 19th century. The care and preservation come under the Heritage Act 1995. (Reference; Victorian Guns and Cannons, South Western Victoria Assessment, May 2008).Cannon, or carronade, 32pdr with wheels. Muzzle loading smooth bore (SB) cannon. Cannon has original wooden Burmese Teak carriage and slide with wrought iron fittings and iron wheels. Manufactured by Carron in Scotland, in 1813. It has been converted from a 28pdr. There is a loop for a rope on the cascabel, which was part of the original casting. Re-bored in 1837. Marks include Serial Number, Royal Cypher of King George III, broad arrow of proofing, and numbers to represent the weight. NOTE: The cannon is displayed in the Warrnambool Botanic Gardens and is mounted on a replica wooden carriage; the original wooden carriage is now stored under cover at Flagstaff Hill Maritime Village. This carriage has 4 wheels on swivel attachments and a central gear that allows the wheels to turn on rails. Pressed into left trunnion “80837 / CARRON / 1813”, cast on barrel“symbol (Royal Cypher of King George III”, “symbol (broad arrow of proofing)” and numbers “45-3-24 / 1837” . Cascable “CV” and marks with gradations from nought to three in quarters on each side, On the carriage the end of one of the main slide members carries the mark “W symbol (broad arrow) D” incised into the timber. Plaque attached to the carriage by the Warrnambool Tritan Woodworkers club, 2010, marking the centenary of the cannon’s relocation in the Warrnambool Botanic Gardens and the addition of the replica carriage. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, victoria’s coastal defences, warrnambool fortification, warrnambool garrison battery, ordinance, armaments, cannon hill fortifications, victorian colonial government, carron ironwroks foundary, 32pdr smooth bore cannon, 28pdr smooth bore cannon, 1813 cannon, carronade -
Bendigo Military Museum
Ceremonial object - SHIPS BELL, HMAS BENDIGO 1941, 1941
HMAS BENDIGO (J187) was an Australian made "Corvette" which served throughout WW2 until 'paid off' on 27 September 1946. The Bendigo Military Museum also holds the last ensign of HMAS BENDIGO, it has a large number of auto graphs. We also hold the wooden crest and Battle Honours Board, this is on loan for 5 years. Refer to Cat 4546 Ensign.1. This is a medium size ships bell. It is cast from Brass. It has a protrusion on the top with a hole in it, used for mounting. The words HMAS BENDIGO 1941 are engraved into the side and painted black. The exterior surface has a few pits, but has been polished numerous times. The interior surface is rough cast, with a large quantity of dints, where it has been struck by the clapper. 2. This is the clapper. There is a steel hook under which is a weight of steel. Under that is a ring. Suspended from the bottom ring is the rope handle. This is an excellent example of navy rope work. At the top of it is a metal ring. Under that is a white and red stylised crown. Under the 'headband' of the crown is a white rope handle with blue inserts. At the bottom is a large rope "Ball" with numerous rope threads of about 180mm length.ww2, ran, hmas bendigo -
Bendigo Military Museum
Uniform - UNIFORM, ARMY, C.1941 - 44
Items issued or made for Henry T RIDGE V57996 & VX148845 CMF & 2nd AIF. Refer Cat No 475.10 for service details..1) Coat, Service Dress, Kahki, winter, 2 x Rising Sun Epaulettes badges, 2 x Australia badges, 2 x colour patches, rectangular white over red with grey surround, Lieut rank badges, 2 on one side, one on the other (missing one), metal buttons. .2) Belt-cloth, Kahki, metal buckle, leather adjustment straps on inside, for .1) .3) Coat, Service Dress, summer, light Kahki, 1 x Rising Sun lapel badge (one missing), 2 x combined cloth Australia and Lieut shoulder badges, 4 pockets, plastic buttons. .4) Shirt, light weight, Kahki, Service Dress summer style, short sleeve, plastic buttons..1) “Wilkes Todhunter, Civil and Military Tailors”, “H.T.Ridge 9/7/41” .3) “Wilkes Todhunter, Civil and Military Tailors”, “H.T.Ridge 3072, 15/7/1941” .4) “Wilkes Todhunter, Civil and Military Tailors”, “H.T.Ridge 7976, 14/1/44uniform ww2, army, officer