This engine was a Commonwealth Aircraft Corporation (CAC) build, and had been upgraded to 92 specification at some time. This engine as acquired, was completely seized and great difficulty was encountered in dismantling it. The pistons in Nos 1, 13, 3, 2 and 5 had "grown" into the cylinder bores requiring some unorthodox methods to remove them. The cylinder barrels have been brought up to a reasonable standard, those beyond repair were replaced from stock. After getting various parts from the US, this engine was eventually brought up to running order.The Pratt & Whitney R 1830 is a double row 14 cylinder air cooled radial engine with a capacity of 1830 cubic inches, (30 litres), developing some 1200 horsepower at a maximum 2700 rpm.Engine Number 54828

The fishing spot known as The Lodge was accessed, for many years, via private property. This article is about an on site meeting, who attended and what was said in regards to the upgrading of a road for access to the river. Includes a letter to the Editor from Ronald Irvine stating their position. Enquiries made on March 11th 2021 with Ronald Irvine revealed that the road had deteriorated and vehicles were becoming bogged, requiring the farmer to pull them out with a tractor. Council were reluctant to fund repairs and the result was that the gate was locked and public access no longer available.Significant because it is a record of community and government discussion about community access to a popular fishing location on the Curdies River.Two page newspaper article from the Cobden Times March 5 1986peterborough, curdies river, the lodge, ronald irvine, the lodge fishing, timboon anglers club, john irvine, the cobden times, 5 march 1986

This family of wheeled armoured vehicles came into use in Australian Army including 8/13 VMR circa 1960. They were phased out and replaced with M113 track vehicles, Technical manuals and User Handbooks were essential equipment for Royal Australian Electrical and Mechanical Engineers (RAEME) tradesmen permanently attached to Armoured Corps regiments as Light Aid Detachments (LAD) or Tech Support Troop (TST) and were responsible for repairs and maintenance of a nature beyond the expertise of AFV crewmen and just short of major rebuilds undertaken by Base Workshop detachments.Part of a collection of workshop manuals and user handbooks relating to equipment on issue to 8th/13th Victorian Mounted Rifles during the latter half of the twentieth century.Two copies of pale green colour soft cover manual, 170 pages with annexures, being Saracen Mk1 APC Provisional User Handbook. String tie binding. Published by UK Royal Armoured Corps, The War Office, November 1954.Ink stamp on title page " 8/13 VMR Regimental Collection " Dyna tape label " 629.28 AMF"manual, military, vehicle, apc, saracen, workshop

Comet was a WW11 British tank. Publication possibly issued to CMF Units in anticipation of receiving Comet tanks in early post war period. Instead Centurion tanks were received, Technical manuals and User Handbooks were essential equipment for Royal Australian Electrical and Mechanical Engineers (RAEME) tradesmen permanently attached to Armoured Corps regiments as Light Aid Detachments (LAD) or Tech Support Troop (TST) and were responsible for repairs and maintenance of a nature beyond the expertise of AFV crewmen and just short of major rebuilds undertaken by Base Workshop detachments.Part of a collection of workshop manuals and user handbooks relating to equipment on issue to 8th/13th Victorian Mounted Rifles during the latter half of the twentieth century.Cream coloured soft covered manual being Inspection Instructions ( Provisional ) Overhaul Comet Tanks. 88 pages and 6 fold out sheets. Stapled on short edge. Published by British Army September 1948Dyna tape on front cover " 629.28.Bri

Document titled "Tramway Maintenance Minutes of 3rd Annual Conference March 30 and April 13, 1953" in the Bendigo and the Geelong offices. See item 9192 for Notes and Agenda for this meeting. Topics covered - cleaning of trams, tracks, track surface repairs, sleepers, car renovation, painting, flooring, notes on a Ballarat Field inspection, disinfecting blinds, electrical systems, truck maintenance, castings, maintenance costs, trolley wheels, employees duties and a summary of actions. Each item where relevant looks back at the actions from the previous conference. Has a list of attendees.Yields information and demonstrates SEC Meeting minutes about discussions between the three Provincial operators about tramcars and operations.Minutes - 50 duplicated foolscap sheets pinned with a folding clip in top left hand corner.trams, tramways, minutes, sec, geelong, ballarat, bendigo, tramcar equipment, maintenance, trackwork, overhead, painting, trolley wheels, motors, one man trams, employees

Items show two different wire terminations - fully wrapped - 7 wires and part wrapped and secured by bending the wire. Shows how the galvanized span wire - 7 strands - can corrode within the insulator and lead to failure if not inspected and replaced. The items were probably erected by the SEC during the mid 1930s and replaced by the BTM 2024. Salvaged from Wendouree Parade during overhead span wire replacement and repair work March 2024 undertaken by the BTM. See also item 9020 for a corroded pole eye bolt.Demonstrates a corroded span wire and a typical egg type insulator.Overhead equipment - two brown egg insulators with associated corroded span wire.overhead, insulators, span wires, btm, tramways

Melbourne’s next-generation trams, G-class, have been designed to be easily repaired with improved visibility for drivers. A prototype has been completed and will be tested by a range of groups before testing on the network in 2025. Department of Transport and Planning’s head of rolling stock development, Ben Phyland, said this redesign was a response to the number of crashes in Melbourne and after consultation with tram drivers. In 2022, there were 960 collisions involving trams and cars, including 166 considered serious – an average of three crashes each day and a 60 per cent increase on 2021. Digital image of a newspaper clipping from the Age titled: "Next-gen tram rolls with the crunches"tramways, g class, trams, planning

This manicure set would have been used in a household in the early 20th century and beyond that date as the contents are usable to this day. The contents of manicure sets do not vary much but the purchase of an expensive silver set would not be common today. This manicure set is of interest as an attractive household item from the past. It will be useful for display.This is a rectangular-shaped wooden box with a black cloth covering. The lid of the box has triangular-shaped sides to allow for the shapes of the contents. The box has two gilt metal clips and the lid is lined inside with padded navy and white cloth. The base of the box is lined inside with navy felt material and has indentations or insets in which to fit the contents pieces. The contents include two pairs of scissors, a nail file, a pair of tweezers, two cuticle repair instruments, a brush or pad and two small jars for holding powder or paste. One jar contains some sort of powder. All the manicure set pieces are made of silver or have silver handles or tops. The silver is tarnished. One pair of scissors may not be the original piece. manicure aids

Yields information and demonstrates SEC Meeting minutes about discussions between the three Provincial operators about tramcars and operations.Minutes - 36 duplicated foolscap sheets pinned with a folding clip in top left hand corner - titled "Tramway Maintenance Minutes of 4th Annual Conference April 26, 1954 and May 1, 1954", in the Ballarat and the Melbourne offices Topics covered - cleaning of trams, tracks, track surface repairs, sleepers, car renovation, painting, flooring, notes on a Ballarat Field inspection, disinfecting blinds, electrical systems, truck maintenance, castings, maintenance costs, trolley wheels, oils and greases, alternation to Maximum Traction trams, spare part, fatigue of axles, accidents, track cleaners, shedmen, union claims,, amenities and a summary of actions. Each item where relevant looks back at the actions from the previous conference. Has a list of attendees. trams, tramways, minutes, sec, geelong, ballarat, bendigo, tramcar equipment, maintenance, trackwork, overhead, painting, trolley wheels, motors, one man trams, employees

Yields information about the view of the City of Ballaarat in 1968 about the possible replacement of tram service.Report or Submission - 6 Gestener printed foolscap sheets, stapled on left hand side and bound with a blue edging tape titled "Submission to Enquiry into Public Transport Facilities in the Ballarat Urban District by A. W. Nicholson, Mayor of Ballaarat Council". Dated 2 April 1968. Submission looks at the possible closure or the future of the tramway system, the SEC involvement, employment, road surface repairs, financial loss to the SEC, reduction in passengers due to car ownership. Council submitted that the tramway system should be retained and extended and that pensioner concessions should be continued. Notes that at the time 69 men on the trams, 18 at the depot and 8 on the track. If replaced by buses, supported a government owned bus provider rather than private. Document scanned - word searchable. pdftrams, tramways, closure, city of ballaarat, bus replacement, public transport, sec, finances

Sixteen page book or booklet printed on A4 white paper, folded to A5 with saddle bound staples, titled "Ballarat's Tramway Preservation Project". Written by Campbell Duncan for the BTPS c1978, giving details of the history of Ballarat's tramways, and a brief history of Geelong and Bendigo, the formation and operations of the BTPS and the tramcar fleet. Has 10 photographs, 1 sketch of the front of a maximum traction tramcar and a map of the BTPS location on the rear. Map drawn by G. Inglis 2.73. Note no credits for photographs. See image files for photos used in book. Second edition - notes tram 28 has been repaired by the BTPS and this did not occur until 1978 - only gives 6 tramcars in list - we had others stored off site at the time. second copy added 1/1/12trams, tramways, btps, museum directory, car fleet, map

Preprinted Melbourne and Metropolitan Tramways Board form with rounded corners, as a Certificate of Service for Leslie James Denmead, dated 29 Dec. 1948. Form 3/278, July 1947 typed with Name, positions held and dates From to Until. All entries have been underlined in red. Gives date of leaving, conduct and service ("Excellent") and signatures of person and Manager. Held positions of Conductor, Bus Driver, Bus starter, Inspector. Signed by L. J. Denmead and by J. Rigaldi (?) District Officer, for the Manager, F. G. Wraith. Sheet has a watermark "BANK M EXTRA STRONG" Not in good condition, has been repaired with 'sticky tape' and is torn. Multiple pin holes and punch hole in top left hand corner and two punch holes along left hand edge.tramways, trams, certificates, mmtb, denmead

Yields information about the way the SEC repair overhead failures on the Ballarat Tramway system - shows the trucks and the crews involved.Black and White copy photograph of a newspaper photograph taken by The Courier of repairs to damaged overhead wire, Lydiard St North, just to the north of the Railway level crossing. Tram services were disrupted as a result. Photo taken 23/4/1965, published 24/4/1965. Shows three SEC vehicles in use, including the tower truck. By the front of the truck, the overhead wire and a set of ears can be seen. The Victorian Railways Institute building is in the background. In the far background is the North Star hotel. The types of truck, from the left hand side are Ford (Tower Truck), International and a Bedford. Collected by Alan Bradley from the Ballarat Courier early 1980's. See Excel file "Record of Ballarat Courier Photos SEC era" (Archive Documents) for source of details.On rear stamped "Copyright, The Ballarat Courier Proprietary Limited." and "85%" in ink in the top left hand corner.tramways, trams, lydiard st nth, overhead, secv, repairs

Demonstrates nature and size of gang undertaking overhead repairs to the tramway in Drummond St. Nth..Black and White copy photograph of a newspaper photograph taken by The Courier, taken 20/4/1968, published 22/4/1968, of repairs to damaged overhead wire, Drummond St North. Shows the tower truck with two men on the truck, one below and an SEC truck parked adjacent. Photo taken at the south end of the Mill St loop. Tram in the photo has probably reversed and showing Victoria St as a destination. Inspector standing adjacent to tram. Photo possibly taken through the windscreen of the car, given the level of the photograph and reflections? in the photo. Collected by Alan Bradley from the Ballarat Courier early 1980's. See Excel file "Record of Ballarat Courier Photos SEC era" (Archive Documents) for source of details.On rear stamped "Copyright, The Ballarat Courier Proprietary Limited."tramways, trams, drummond st nth, overhead, sec

Track repairs in Wendouree Parade, June 2014. 6022.1 - Roger Gosney standing on track looking at damaged section 6022.2 - Close up of damaged section of track 6022.3 - Work crew including dog in safety vest 6022.4 - Work crew digging up road watched by the dog 6022.5 - Close up digging up road, Alan Snowball using jackhammer, Greg Robinson with spade, Roger Gosney on the far side with spade, and Barry Richardson with spade. 6022.6 - Greg Robinson in trench watched by Alan Roger, and Barry 6022.7 - Same group looking into the trench 6022.8 - Alan on hands and knees beside trench preparing for welding 6022.9 - preparing for welding, with safety screens in place. 6022.11 - Greg Robinson and Roger Gosney resting beside Wendouree Parade. (no. 10) Photo by Peter Waugh, collected for reference purposestrams, tramways, road works, btm, track repairs, wendouree parade

Black and white photograph / postcard of a collision, accident, between SEC Ballarat No. 14 and a motor truck at the intersection of Drummond St. North and Webster St. May or June 1939. Official SEC photo, there are other photos of this collision in the collection. See Reg Items 580, 1019, 1365 and 1366 and 3904 for larger prints of these photographs of these photographs and further details. See also Reg Item 6211 for a fridge magnet version. Printed in Ballarat by???. On the rear has the words "Ballarat Tramway Museum / Historic Collection No. 1, Photo copyright Wal Jack 1962" Has a divided back with a 8mm thick black line on the right hand side. The tramcar body card shows it was repaired following an accident June 1939. (Note added 2-2-19). trams, tramways, ballarat, drummond st nth, accidents, tram 28

Set of two typed reports detailing Preston Workshops. .1 - Report - marked draft, dated 24/11/1926 - 4 foolscap pages with marks, corrections, changes outlining the need for a workshop, refers to the Malvern depot, acquisition of the land, design, capacity, description of the various shops. Gives a description of the operation, construction of trams in the future, notes the cable repair shops at Nicholson St, cranes, employee numbers, costs, paint and body shop. Notes the mess room and that an ambulance room will be provided. .2 - Report - 3 quarto pages - undated - but based on the first sentence, c1929 - titled "Tramway Workshops Preston". Gives a description of the workshops, the main groupings, building sizes, cranes, floors, building and maintenance capacities, tracks, admin block, employment, sub-station and power supplies.In top right hand corner of each sheet of .1 "Reference RS 49/1" stamp and handwritten.trams, tramways, preston workshops, malvern depot, nicholson st, workshops, workplace conditions

Set of eight Black and White photographs of the major repairs to the roof of Z8 - c1980? done at Preston Workshops. .1 - the new section being craned into position - has a W class car in the background. .2 - internal view showing a support structure. .3 - external view with the support structure - possibly before the section of roof was removed. .4 - view of the inner roof? wit siring in position. .5 - ditto .6 - internal view of the roof section being removed or installed - shows the insulation. .7 - external view showing roof support structure in place ,8 - showing what appears to be the original roof being removed. This record will need some further research work, not possibly during COVID 19 issue. MMTB Photostrams, tramways, z class, repairs, preston workshops, tramcar construction, tram 8

Foolscap Manila Folder titled "PCM Tram Equipment" with the following papers secured with an Arnos binder. Many of the documents seem to have been copied onto heat sensitive paper. Have tissue paper separating them. 1. Wiring Diagram - GE PCM Control Equipment - R4284B. 2. Westinghouse - Load test on Repair Railway Motors 3. Letter to Chief Engineer MMTB from Australian General Electric - 23/7/1935 - re delivery of 15 cases of PCM Equipment by ship and attaching drawings. 4. Drawings and maintenance notes for above - includes field shunts, magnet valves, cases, 5. GE Specification Ry-5313 - General Electric PCM Control for 4-40HP 600Volt Motors with Shunted FieldsOn rear cover in ink "To Norm Cross"trams, tramways, electro pneumatic, pcm, controllers, general electric, mmtb, tramcars

A blowtorch or blowlamp is a fuel-burning tool used for applying flame and heat to various applications, usually metalworking. Early blowlamps used liquid fuel, carried in a refillable reservoir attached to the lamp. Modern blowtorches are mostly gas-fuelled. The blowlamp is of ancient origin and was used as a tool by gold and silversmiths. They began literally as a "blown lamp", a wick oil lamp with a mouth-blown tube alongside the flame. This type of lamp, with spirit fuel, continued to be in use for such small tasks into the late 20th century. In 1882, a new vaporizing technique was developed by Carl Richard Nyberg in Sweden, and the year after, the production of the Nyberg blow lamp started. It was quickly copied or licensed by many other manufacturers. Carl Richard Nyberg (May 28, 1858, – 1939) was the founder of Max Sievert’s Lödlampfabrik, then one of the largest industries in Sundbyberg, Sweden. After school he started working for a jeweller and later he moved to Stockholm and worked with various metalworks. 1882 and set up a workshop at Luntmakargatan in Stockholm making blowtorches. However the business didn't work well because it took too long to both manufacture and sell them. In 1886 he met Max Sievert (1849 - 1913) at a country fair and Sievert became interested in Nyberg's blowtorch and started selling it. In 1922 the company was sold to Max Sievert who continued to own it until 1964 when it was bought by Esso. The blowtorch is commonly used where a diffuse high temperature naked flame heat is required but not so hot as to cause combustion or welding: soldering, brazing, softening paint for removal, melting roof tar, or pre-heating large castings before welding such as for repairing. It is also common for use in weed control by controlled burn methods, melting snow and ice from pavements and driveways in cold climate areas, road repair crews may use a blowtorch to heat asphalt or bitumen for repairing cracks in preventive maintenance. It is also used in cooking; one common use is for the creation of the layer of hard caramelised sugar in a crème brûlée. A brass blowtorch, 'Sievert' with a wooden handleSIEVERTtools, blow torches, blow lamps, welding, brazing, jewellery, cookery, soldering, nyberg carl, sievert max, stockholm, sweden, spirit fuel, kerosene, gas fuel, moorabbin, bentleigh, cheltenham, market gardeners, pioneers, early settlers, plumbing, carpenters,

The FS-24 Phonix is the first sailplane design to be built using a moulded fiberglass sandwich technique. It was designed by Hermann Nagele and Richard Eppler leading a group setup for the purpose at Stuttgart Technical University in the early 1950s. Initial construction was undertaken at workshops of Wolf Hirth and the first prototype was completed at the Bolkow Aircraft Company where Nagele and another member of the group, Rudi Lindner, had gained employment. It flew on 27 November 1957. Two further prototypes were built incorporating a T-tail and other refinements. Eight in all were built before production was stopped in 1961. A number of gliding records were broken in Phonix sailplanes in Germany in 1962-1963. It was found to have a best glide ratio of 40:1. The Museum’s example, No. 403 was originally a prototype built on 25 May 1960 [Registration D-8354]. It was converted at Bolkow to a Phonix T in 1963 and sold to a private owner in Switzerland [Registration HB-746] and later then to gliding club Segelfluggruppe Solothurn in 1965. The glider returned to Germany in 1971 (Meersburg) and re-registered as D-0738. It moved to a new owner in Allershausen in 1976, and again to Lindhoft in 1982. In 1983 the glider was sold to owners at Hasselt, Belgium and given registration OO-ZQD. In 1989 a further change of ownership occurred and the glider went to Leusden in the Netherlands where it was registered as PH-949. In 2006 the Phonix No.403 was imported into Australia by John Ashford of the Geelong Gliding Club. On 30 January 2007, it was registered as VH-GRP. However, as at January 2016 it has not been flown in Australia. In the course of its flying history the glider was damaged several times and repaired. At one stage a larger rudder was fitted and later on this modification was reversed. With the original conversion to a Phonix T and subsequent repairs and changes to equipment the weight of the airframe increased from 182 kg to approximately 220 kg. Nevertheless, the wing loading is a modest 20kg/square metre. As at January 2016, minor repairs and airworthiness certification are required to return the glider to flying condition. This exhibit is highly significant as it is one of only eight of this pioneering sailplane design. It is the only one in Australia. Glassfibre single seat sailplane, finished white with blue stripes on fin and rudder.Australian registration GRP on rudder; Serial Number 403 and Vintage glider club of Netherlands plaque in cockpitaustralian gliding, sailplane, glider, fs-24, phonix, nagele, eppler, lindner, stuttgart technical university, bolkov aircraft company, segelfluggruppe solothurn, ashford, geelong gliding club.

A penknife, or pen knife, is a small folding knife. It was originally used to describe a knife used for cutting or sharpening a quill to make a dip pen nib. Originally, penknives were used for thinning and pointing quills to prepare them for use as writing instruments and, later, for repairing or re-pointing the quills. They did not necessarily have folding blades, but resembled a scalpel or wood knife by having a short, fixed blade at the end of a long handle. Today a penknife can have single or multiple blades, and with additional tools incorporated into the design. The most famous example of a multi-function penknife is the Swiss Army knife A folding pen-knife with 2 stainless steel bladeson long blade end; STAINLESS / MADE IN / SHEFFIELDpen-knife, scouts, cheltenham, moorabbin, bentleigh, tools, early settlers

In 1843, Frederick Stanley, started a small shop in New Britain, USA, to manufacture bolts, hinges, and other hardware from wrought iron. Among the early settlers in Moorabbin Shire were blacksmiths who made tools for the other settlers who were establishing the homes, market gardens, farms, orchards and various businesses. Early settlers were self reliant and repaired their own equipment for kitchen,dairy, farm, horses, carts using various tools . As manufacturing developed late 19thC high quality tools were imported from UK, USA and EuropeThese set squares are typical of the type used by early settlers in Moorabbin Shire c19002x Steel Set Squares a) 15cm (6") with wood handle b) 19cm (7") with a slotted steel handle. a) STANLEY Pat 12-29-96set squares, rulers, builders, trigonometry, mathematics, stanley tools pty ltd., bolts, hinges, hardware, early settlers, market gardeners, blacksmiths, tools, building equipment, hammers, moorabbin shire, bentleigh, mckinnon, highett, cheltenham,mcewan james pty ltd, melbourne, bunnings pty ltd,

Part of the Zakrzewski Collection of spinning wheels donated to the National Wool Museum by Mr Wlodzimierz Zakrzewski. For many years, Mr Zakrzewski collected, researched and repaired spinning wheels from all over the world. This wheel is from Yugoslavia and dates from the early 20th century. It is made from Poplar Alba. The treadle bar runs obliquely from beneath the right arm of the T-shaped base to beneath the stem of the T. The mounting of the wheel and the flyer mechanism are reversed. This is in order that flax may be spun with one hand or that plying may be done. It was purchased by Sobieski Galleries, Glen Iris.Part of the Zakrzewski Spinning Wheel collection.handicrafts - history flax, spinning wheels, highlights of the national wool museum: the zakrzewski spinning wheel collection - exhibition (28/07/2001 - 02/12/2001), zakrzewski, mr wlodzimierz, handicrafts - history, flax

Part of the Zakrzewski Collection of spinning wheels donated to the National Wool Museum by Mr Wlodzimierz Zakrzewski. For many years, Mr Zakrzewski collected, researched and repaired spinning wheels from all over the world. This is a German wheel for spinning flax and it dates from the 19th century. The plaque on the back gives the name of the original owner: Anna Dorothea Adelheid Gruther from Orbinghausen, Germany. The date presumably refers to when she was given the wheel. It was purchased from Mr Eric Corran, a manufacturer of looms and spinning wheels and was in extremely poor condition before being restored by Mr Zakrzewski.Part of the Zakrzewski Spinning Wheel collection.Anna Dorothea / Adelheid Gruther / in Orbinghausen 1868.handicrafts - history flax, spinning wheels, highlights of the national wool museum: the zakrzewski spinning wheel collection - exhibition (28/07/2001 - 02/12/2001), zakrzewski, mr wlodzimierz gruther, anna dorothea adelheid, handicrafts - history, flax

This vehicle was used for patient clinic runs between Morabbin and Kingston Hospital. It then was modified into an ambulance mobile communications vehicle. Found to be too small to fulfil this role it was later allocated to the Healesville State Emergency Service. It then returned to Ambulance Victoria where it was stored at Eltham for ten years. The vehicle was repaired mechanically by Bill Redpath in 2016 and repainted. It will be restored internally by AHSV members and former MICA paramedics to represent Car 208, Victoria's and Australia's first Mobile Intensive Care Ambulance (MICA). The AHSV holds some of the original equipment from Car 208 and this will be refitted into the Dodge.White Dodge Ambulancedodge, mica

The last train to Beech Forest ran on 30 June, 1962. The train had a particularly motley look to it; 180 passengers were loaded into NU goods vans which had been hastily fitted out with temporary seats and tarpaulin roofing. The train was hauled by the dilapidated G42 locomotive, kept alive through patch-up repairs and cannibalised G41 parts, which intending travellers looked at with some trepidation. The train made it without mishap. When it returned to Colac on that cold, gloomy June day it signalled the end of narrow gauge operations in the Otway Ranges.B/W. Locomotive G42 with the sign " Australian Railway, Last Train to Beech Forest, 30-6-62, Historical Society" is departing Colac. NC guard's van and NU louvred van are attached. A woman and man watching. .colac; beech forest; railways;