Completely assembled with gas bottle attached. Chrome carry handle. Anodised white lid over four light steel strutts. Steel gas feeder area 7cm. Sticker with instructions. Jenaar Suprax Glass is cracked. Insignia made in Germany. Cylinder 3965c.Bottle T/77 8, 52885 S Vic. Appro TP 3310 KPa + 4 77A^ AS no B115-240. Companion Tara 3.5 kg - no 21836. Propane type PS 39650 WC 480kg Tare 7lb 11pz

Tilley Floodlight Projector - Model FL6 It stands about a metre high, and when lit, turns out about 5,000 candle power from the parabolic mirror in the back of the lamp. manufactured between the mid 1940's and early '50's It runs on kerosene that is pressurized with the integral pump, to provide a light beam from the parabolic mirror in the back of the lamp of approximately 3,000 candle power which can project over 1/4 of a mile. It features a pressure gauge, armored glass and all steel construction. Historic - Railways - Tilley Floodlight ProjectorTilley Floodlight Projector - Model FL6 made of metal, brass and glass and steelTilley Floodlight Projector - Model FL6puffing billy, tilley floodlight projector

Kerosene was used to light the signal lamps at night time on a railway, to ensure that a locomotive driver could see that the line was clear there was no danger of another train ahead. This container was used to store the in kerosene to fuel such lamps and was kept inside a lamp room until required for use.Victorian Railways - Keroseane Container Used in the storage of kerosene prior to use in lamps at stations.Large, cylindrical tin container with conical lid and wire handle. A small zinc spout is embedded in the lower quadrant. The word 'KERO' is stencilled in white across the front. Keropuffing billy, kerosene, fuel, combustible material, tin container, lamps

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

Four NSWTD Railway marker Oil lamps at Nobelius Packing shed Item stamped numbers unknown Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil LampFour NSWTD Railway marker Oil lamps made of metal and glass Railway lamp, paraffin, metal / glass / fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870-1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTDpuffing billy railway , pbr, four nswtd railway marker oil lamps

Lake Bolac Post Office Glenelg Highway. Initially the Post Office was established at the Store in 1868. This official weatherboard building was opened in 1887 incorporating a telegraph office, money order office and post office savings bank. The Post Office business was relocated in 1944 and the building was used as a private residence with the front room leased to Dennys Lascelles. Note the horse hitching rail and kerosene street light.Photograph depicting a weatherboard building across a road. The building is fenced. In front of the building there is a telegraphic or electric post and a lamp post.lake bolac, post office, glenelg highway, dennys lascelles

The convention was held in the Palmerston Street Methodist Church, Carlton on June 6th, 7th, 8th, & 9th 1928. The convention was arranged by the Methodist Local Preachers' Association Melbourne Branch. Small program for the 14th Holiness Convention. It made of raw umber light card and with black text.Front cover: "The Book of Life" "June 6th, 7th, 8th, & 9th 1928" Back cover: "Thy word is a lamp unto my feet, and light unto my path. Psalm 119.105"methodist local preachers' association melbourne branch, palmerston street methodist church

It is unknown how this came into the collection at the Warrnambool Museum. However, during the 18th and 19th centuries it was fashionable for young men of means to undertake a 'grand tour'. During their travels they would often pick up souvenirs with these sometimes being ancient artefacts from classical Greece or Rome. It is thought that the item most probable came to the museum in this manner.From discussion with specialists at the British Museum and the University of Reading it was ascertained that the oil lamp is indeed ancient Roman and over 2000 years old. The marking on the top could be Venus although it is quite worn away so it is difficult to tell for sure.A terracotta oil lamp housed in a wooden box. On the top of the lamp are 3 circle incisions and in the centre of the circles is a depiction of a figure. There is a small finger sized handle on the side of the lamp. The handle has 2 incised lines leaving 3 raised ridges. It is squared off at the top. The top of the oil lamp has a hole in which to place a cloth wick and a spout from which the smoke would have come out. The spout is blackened from smoke. The container box is guessed to be from the time of acquisition which would be around the early 1900s and is made from a polished wood. Light in colour.In the box was a label saying, 'Venus coming out of the gate of the temple'. It also stated that the lamp may have been placed at the feet of the dead in the catacombs.oil lamp, roman, terracotta, classical, archaeology, victorian, grand tour

The donor received the projector from a relative. He used it in the City of Whitehorse and surrounding areasWaterworth Slide Film Strip Projector, Model A - 300 watt, without a fan but with ventilating slots on top and an open bottom for air to flow. It has a carrying handle and a power lead with 3 pin plug which is wired in permanently. The projector lamp is at rear under the carrying handle. Image is projected through three stage lens via via the image on the 35mm strip or slide. The front lens is adjustable for focus. A knurled nut enables a height adjustment at front. Slides are inserted through the holder - whilst one slide is shown the other can be loaded ready to be slid in front of the light. The film strip holder is missing. The unit is finished in a grey hammer finish paint used in 1960 t0 1980s. The operating instructions are filed in the supplementary envelope. The projector is stored in a hand made three ply hinged box.Waterworth Hobart 5553Aphotography, projectors

Lamp used to warn of dangerous area or objects on road, footpath or railway gates owned by Council or the Railways. This one belonged to the Country Roads Board of Victoria.Red painted outer case with lid. Inner red glass lamp and kerosene holder with wire to lift out for filling. Gaps all round to allow light to shine out and to let air in to allow lamp to burn. Country Roads owned.lighting, kerosene & oil

Fittings out of the Mitcham Station Master's house, the last block of land on the east side of Station Street, now a car park. Railway Department house number 1273 brass and ceramic light switches. 2 brass picture hooks. 1 brass and lead counterweight for lamp. 2 gas jets on wooden base. 1 door bell pull. 2 brass curtain holders. All on wooden base.metalcraft, brassware

Colour photograph of the street light outside her Majesty's Theatre, Ballarat.Colour photograph of a street lamp outside Her Majesty's Theatre, Ballarat, 2020her majesty's theatre, ballarat, lydiard street south, lamp, gas lamp

Chrome Bicycle lamp has round glass lens at the front with red reflectors at the side and facing the back. Mounting clips are at the back. The top has a screw lid for fuel. and a regulator. Fuel is stored in a cylindrical container attached to the light's lens area. Cracked lensPanther B'Ham (on top of fuel cylinder)bike, bicycle, lamp

Solid metal base with decorative pattern. on-off switch is on base. Flexible metal upright leads from the base to the light globe socket (globe missing). This is covered by a metal half-sphere hood. Lamp has no electric cord attached.light, electric, desk lamp

This photograph is taken in the bedroom of the man's home in the suburbs of Melbourne. It depicts one of the types of nursing care given by Melbourne District Nursing Society (MDNS) Sisters in the community. The Sister is visiting the man's home and is administering an injection which has been ordered by a doctor. Glass syringes were used by the Society until the mid 1960s and were re sterilized for future use. After this time plastic disposable syringes were used.The Trained nurses of the Melbourne District Nursing Society (MDNS), later known as Royal District Nursing Service (RDNS), visited patients in their home and gave best practice care in many fields of nursing and to people of many cultures throughout its 130 years of expansion. Initial visits not only assessed the specific nursing situation but the situation as a whole. Their patients ranged in age from babes, children, adults to the elderly and referrals were taken from Hospitals, General Practitioners and allied Health facilities. Some of the care provided was: – Post-Natal care given to mother and babe, Wound Care following various types of surgery, accidents, burns, cancer, leg ulcers etc. Supervising and teaching Diabetic Care, including teaching and supervising people with Diabetes to administer their own Insulin, and administering Insulin to those unable to give their own injections. Administering other injections and setting up weekly medication boxes. The Sisters performed Catheterizations on adults suffering from conditions such as Quadriplegia, Paraplegia, Multiple Sclerosis (MS), Motor Neurone Disease (MND) and Guillan-Barre Syndrome, and when required at school on children for e.g. those with Spina Bifida. The Sisters visited those requiring Cystic Fibrosis support and care; those requiring Haemo-Oncology care, including visiting children at school; those requiring Home Enteral Feeding care, and those requiring IV therapy at home and home Dialysis. Palliative Care was given including pain relief with the use of syringe drivers, personal care as needed, and advice and support to both patient and family. RDNS provided Stoma management to those needing Urostomy, Ileostomy and Colostomy care and those requiring Continence care. HIV/AIDS nursing care was provided; visits to Homeless Persons were made. Personal care was given to patients ranging in age and with varying mobility problems, such as those with MS, MND, Guillan-Barre Syndrome, Quadriplegia, Paraplegia, Acquired Brain Injury, following a Cerebrovascular Accident (Stroke), those with severe Arthritis and those with a form of Dementia. When necessary the elderly were assisted with personal care and advice given on safety factors with the use of hand rails, bath or shower seats, and hand showers. Rehabilitation with an aim towards independence remained at the forefront of the Sister’s minds and when possible using aids and instruction on safe techniques enabled the person to become fully independent. All care included giving advice and support to the patient and their Carers. The Sisters liaised with the persons Doctor, Hospital and allied Health personal when necessary.On the left of this black and white photograph, is a Melbourne District Nursing Society Sister who is standing side-on and leaning slightly forward as she administers an injection into the right upper arm of a gentleman to her right who is sitting up in bed resting against two white covered pillows. The male patient has short dark hair; is wearing glasses, and is looking up at the Sister. He is wearing a thick grey cardigan over a pale colour pyjama top which has dark piping; the lower part of his body is covered by a dark and light coloured check bed cover. The bed has a solid wooden headrest with a bed lamp attached to its upper right. The Sister who is wearing her uniform grey brimmed hat over her dark short hair, is wearing a white gown over her grey uniform, the collar of which is seen. Three fingers of her left hand are holding back the pushed up sleeve of the man's cardigan and she is holding a white swab between her thumb and first finger. She has a glass syringe resting in her right hand with her thumb and forefinger resting against the lower glass and metal section of the syringe; part of the metal needle is seen, the rest is inserted in the mans upper arm. On the far left of the photograph part of a dressing table mirror can be seen.' Rough Proof' Latrobe Studios Ref No. 59134-8melbourne district nursing service, mdns, royal district nursing service, rdns, rdns - injection

Yields information about the materials and the methods of installing electrical domestic cables in Ballarat houses during the 1920's.Section of timber or wooden electrical conduit used in houses c1920, to contain wires for electrical lamps and fittings. Consists of a timber base (very light softwood - ??) with two slots that was nailed to a wall and after the cable installed a cover strip applied. Has one end mitred or cut at 45 degrees. See Early Electrical wiring systems in American buildings - L. D. Mitchelltrams, tramways, esco, electrical equipment, house extensions, houses, electricity

.1 - Book - 56 pages + grey covers, side stapled, issued by the British Engineering Standards Committee "Electrical Machinery excluding motors for traction purposes", No. 72-1917, September 1917. Has "Commonwealth Engineer" label along the bottom edge. .2 - Book 28 pages - light grey covers, side stapled, issued by the British Engineering Standards Association, "Insulating oils for use in Transformers, oil switches and circuit breakers" No. 148-1923, April 1923. Has a Tait Book Co. stamp along the bottom edge and ESCo date stamp 1 Oct. 1925. Printed by Gaylard & Sons London. .3 - Book 72 pages - light grey covers, side stapled, issued by the British Engineering Standards Association, "Tungsten Filament Electric Lamps" No. 161-1925, August 1927. Has a Tait Book Co. stamp along the bottom edge and ESCo date stamp 15 Feb. 1928. Printed by Waterlow & Sons London. .4 - Book 48 pages - light grey covers, side stapled, issued by the British Standards Institution, "Metal Sheathed paper insulated plain annealed copper conductors for electricity supply including voltage tests" No.1 48-1933, March 1933. Has a Tait Book Co. stamp along the bottom edge and ESCo date stamp 15 Feb. 1928. Printed by Waterlow & Sons London. trams, tramways, power station, standards, materials, electrical systems

Military communications and signaling equipment used from 19421942 portable morse code set with a day signaling light and spare globes. All fitted in timber carry case with webbing strap.Plate "Lamp Signaling Daylight. Short Range Case MK IIPMG MELM1942" S/N 10356. Operating instructions on spare globes box lidmorse code, wwii, signaling

An anchor light is a white light visible from all around the vessel and is required when anchored or moored between sunset and sunrise. The best place for this light is usually at the top of the highest mast.Example of a kerosene lamp used as an at anchor light.Navigational Light or Riding Light run on oil or kerosene which is displayed by a ship at night when lying at anchor.night light, navigational lighting, kerosene lamp, sailing ships

The Loch Ard is historically significant as one of Victoria and Australia's worst shipwreck tragedies. It is archaeologically significant for its remains of a large international passenger and cargo ship. It is highly educationally and recreationally significant as one of Victoria's most spectacular diving sites, and popular tourist sites in Port Campbell National Park.Round stem base glass saddle glass light saddle, shipwrecks, loch ard

Set of two drawings (BA-T8-8100/1 and BA-T8-8100B) showing the installation of tail lights on SEC tramcars and modifications to the battery/trolley pole relay and battery. Both are dated 15/11/1949 and signed by the Manager Ballarat Branch. The actual relay used later was a Post Office type relay contained within a wooden box.Yields information about the modifications proposed to the tramcars to provide a rear tail light and lights when at a terminus.Drawing - dyeline print on plain papertramcars, safety, tail lights, lights, ballarat

Prior to the launch of the motor powered Queenscliffe, three row boats were in service as lifeboats. This lantern was part of the equipment of the third lifeboat up to 1926.A brass lamp which was part of the safety equipment on board the Third Queenscliff LifeboatBrass Lantern with interchangeable port and starboard glass filters run of kerosene.Brandt Bros Melbourne Manufacturers 422 Elizabeth Streetlight, navigational safety

This signal lamp was originally fitted on the steam tug 'Wattle'RAN Career 1932 to 1969: Wattle's construction and career as a non-commissioned vessel of the Royal Australian Navy. Saved from the Scrapyard 1969 to 1979: Sydney-based enthusiasts rescue Wattle from the scrapyard, forming an association with Sydney Heritage Fleet. Melbourne Pleasure Steamer 1979 to 2007: A volunteer group brings Wattle to Melbourne to restore, then sails Port Phillip on outings and excursions. Restoration Journey 2007 to 2015: Wattle is hoisted onto the hard to undergo major restoration work. Back in the Water, 2015 to present: Wattle returns to the water for further restoration, and in 2019 sails again on Port Phillip.Brass candle powered signal lamp with a lens circumference of 14cm, mounted on a timber plinthSundercombes Patent Eclipsesignal light, marine fittings, steam tug 'wattle'