Chinese gold scales. Wooden scale holder (a) two part wooden device secured at end of handle with a metal pin to allow swivelling of both pieces. At end of handle, two pieces 'violin' shaped to hold scale and weights. This enabled placement of scales within holder. Bottom piece has indent for scale pan, weight and long handle. Chinese scale (b) thin cream handle marked with inch graduations, without numbers. Separately suspended from handle with thick cotton is a small semi-circular lead weight and a round brass scale pan.gold mining, mining equipment, chinese gold scales

A small 12oz weight made by a British company in West Bromwich called Archibald Kenrick and Sons. This was found by QC Binks whilst he was out metal detecting for gold.bendigo, gold mining, qc binks, archibald kenrick and sons, qc binks, weights.

Pint measureMetal jug and boxweights & measures

V.R. Powder & General Goods Van NH1 Gauge 2'6" The NH Powder and Goods van was built in 1910. Its purpose was to carry explosives and general goods, Originally classed as NPH. There were two compartments: a 10ft 8¾ inch (3,270 mm) section for explosives and a 13 ft 7 in (4,140 mm) section for general goods. The sides, ends and doors were covered in sheet metal. With the closing of the mines at Walhalla the need to carry explosives ended and both compartments were used for general goods. The doors were replaced with NU type louvre doors for ventilation. NH1 Covered Truck Service History : NPH NPH 1 was built and issued to traffic June 1910. It was a bogie boxvan set up for general goods and the transportation of explosives. It could carry 6 tons of goods and 4 tons of explosives. No doubt the van was stationed on the Moe - Walhalla line. Walhalla was a gold mining town and the rail line had been built from Moe to provide a faster means of transportation than bullock teams from the sailing boats from Melbourne to Port Albert/Sale via Heyfield. In 1911 the van was converted to all goods transport and recoded to NH. NH The van was fitted with autocouplers in 1928. It was scrapped in 1954. By 1968, the vehicle body had been found and was placed into the Museum at Menzies Creek. Body donated to the Puffing Billy Preservation Society. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1910 Number Built 1 In use - Static displayHistoric - Victorian Railways - narrow gauge rolling stock - Powder & General Goods Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collection1 NH - Powder & General Goods Van Made of Timber - wood, wrought iron and metal sheet There were two compartments: a 10ft 8¾ inch (3,270 mm) section for explosives and a 13 ft 7 in (4,140 mm) section for general goods. The sides, ends covered in sheet metal with NU type louvre doors for ventilation. NH1 To carry 10 tonspuffing billy, powder & general goods van nh1, nh1, powder & general goods van, victorian railways, narrow gauge rolling stock

NNN - BALLAST HOPPER, This vehicle was built by the Tasmanian Govt. Railways in 1954 and classified QG. A number were obtained by the Puffing Billy Railway for use on ballast trains but to date, only two have been converted. When the first of these was converted for 2’6” gauge operation it kept the Tasmanian QG but with the addition of an N prefix, and also kept its Tasmanian number of 3. However, to follow traditional V.R. practice, in June 2003 it was reclassified to NNN and numbered 1 as the nearest counterpart on the V.R. was the broad-gauge NN. A second one, numbered 2, has since been converted. 1 NNN - Bogie Ballast Hopper Truck Service History Built 1954 Tasmanian Railways - QR 3 - Bogie Ballast Hopper Truck converted from a 3ft 6 inch (1,068 mm) gauge ex Tasmanian Railways ballast wagon by the Puffing Billy railway. Coupled Length 20 feet 0 inches (6100 mm) Weight 6 tons Capacity 10 tons Number Built Not known In use 1 To be restored 3 Puffing Billy Service History or Notes Historic - Tasmanian Government Railways - 3 QG Bogie Ballast Hopper Truck Puffing Billy Railway - Track maintenance Vehicle - NNN - Bogie Ballast Hopper Truck1 NNN - Bogie Ballast Hopper Truck made of Steel and metal1NNNpuffing billy, pbr, rolling stock , 1 nnn bogie ballast hooper truck, tasmanian government railways, 3 qg bogie ballast hopper truck

NNN - BALLAST HOPPER, This vehicle was built by the Tasmanian Govt. Railways in 1954 and classified QG. A number were obtained by the Puffing Billy Railway for use on ballast trains but to date, only two have been converted. When the first of these was converted for 2’6” gauge operation it kept the Tasmanian QG but with the addition of an N prefix, and also kept its Tasmanian number of 18. However, to follow traditional V.R. practice, it was reclassified to NNN and numbered 2 as the nearest counterpart on the V.R. was the broad-gauge NN. A second one, numbered 1, was also converted. and was reclassified to NNN in June 2003 2 NNN - Bogie Ballast Hopper Truck Service History Built 1954 Tasmanian Railways - QR 18 - Bogie Ballast Hopper Truck converted from a 3ft 6 inch (1,068 mm) gauge ex Tasmanian Railways ballast wagon by the Puffing Billy railway. Coupled Length 20 feet 0 inches (6100 mm) Weight 6 tons Capacity 10 tons Number Built Not known In use 1 To be restored 3 Puffing Billy Service History or Notes Historic - Tasmanian Government Railways - 18 QG Bogie Ballast Hopper Truck Puffing Billy Railway - Track maintenance Vehicle - NNN - Bogie Ballast Hopper Truck2 NNN - Bogie Ballast Hopper Truck made of Steel and metal2NNNpuffing billy railway, pbr, rolling stock , 2 nnn bogie ballast hopper track, tasmanian government railways, 18 qg bogie ballast hopper truck

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 125 NQR - Open Medium Truck 20/ 5/1910 NWS Built new VR Service History *NQR 125.VA - 20/ 5/1910 NWS Built new - / /1926 - To NQ 125.VA - Puffing Billy Service History or Notes Untrafficable at Emerald Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck125 NQR - Open Medium Truck made of Steel and metal125 NQRpuffing billy railway, pbr, rolling stock , 125 nqr - open medium truck, nqr open medium truck, victorian railways

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 23 NQR - Open Medium Truck VR Service History - NQR 23.VA - 10/12/1898 NWS Built new - / /1926 - To NQ 23 Puffing Billy Service History or Notes Untrafficable at Emerald Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck 23 NQR - NQR at Emerald - Open Medium Truck made of Steel and metal23 NQR puffing billy railway, pbr, rolling stock , ? nqr - open medium truck, narrow gauge rolling stock, nqr wagon, 23 nqr, victorian railways

Long case clock in painted wooden case. Timber moulding to top. Gold coloured dial with Arabic numerals. Black (1-24) metal. No makers name on dial. Brass pendulum on wooden hanger with 3 brass weights.longcased clock

Kitchen scales comprising of six separate pieces - a heavy metal stand supporting a moving section with circular piece at one end to take the weights (of which there are four - 4oz, 8oz, 1 lb and 2lb) and a two-pronged cradle at the opposite end to support the tin receptacle for holding ingredients to be weighed. Ornate pattern around foot and weights stand.Weights with numbers on top. 1lb weight also has a 2lbs in centre circle and Imperial Standard around inner circle.scales, kitchen

Postal Parcel Balance Scales - circular face with weights and costs around circumference - encased in heavy metal frame with ornate pattern around the triangular foot - oblong flat tin tray balanced on top - painted white with black markings on the face - single black metal hand in centre to show weight etc.In centre of face: "POSTAL PARCEL BALANCE" / SALTER'S "Salter" over emblem showing arrow through knotted rope / 11 LB'S BY 1 OZscales, postal

The Villa Alba Museum is cultural institution committed to the collection, study and display of 19th century interior decorative finishes, and the components of 19th and 20th century interior decoration. These include artefacts (wallpapers, textiles, carpet samples), furnishings, printed materials (catalogues, books, periodicals), and pictures (photographs).Part of a group of curtain furnishings which includes a curtain with original fittings, fringe and braid unpicked from other curtains, and these six curtain tie backs. The six curtain tie backs are identical, though one pair is shorter. The tie backs comprise a length of soft, loose (floss) silk cord, made of two thick strands twisted together (cable cord). An elaborate tassel is attached to the middle of each cord, to weight the tie back in an elegant loop, with the loose ends attached to hooks or pins on the window frame. Each tassel is formed of a turned wooden mould, covered with floss silk thread, and further decorated with knotted netting, applied braid, and glass beads. The end of the mould has a large flattened shape, from which hangs a ring of long, bullion metal fringe. This may be silver-gilt: untarnished parts are still true gold colour, while the majority of the fringing is tarnished black. These curtain decorations are truly luxurious; the original suite of curtains would have been very expensive, an eloquent item of conspicuous consumption of luxury goods.Attached handwritten note : "VA Th 7/6/2012 Ric Freeman (Nat Trust member) & Julie Freeman / re soft furnishings, tassels, trimmings, braid set / Jessie, Terry (and Chris St) to view, collect"decorative arts & design, interior decoration - history, curtain accessories, tassels

A prayer wheel is used in Tibetan Buddhism for personal worship. Tibetans believe that spinning the prayer wheel which as thousands or millions of mantras inside is equal to saying that many mantras, while being done in a fraction of the time. This helps accumulate merits, purify negative karma and obstacles on the path to enlightenment. This wheel has a hollow metal cylinder attached to a rod handle, made of ivory (with carved elephants), inlaid with coral and turquoise. Inside the cylinder is a tightly wound scroll printed with numerous mantras and wrapped around a spindle. The cylinder is embossed and decorated with inlaid coral and turquoise. A chain with a small weight at the end (made out of copper alloy) is affixed to the cylinder, allowing it to be spun by a slight rotation of the wrist. tibetan buddhism, holy objects, worship devices

The knitting needle gauge was used as a guide to the needle sizes used in Britain and Australia before metric measurements were adopted for weights and measures in the mid 1970's.A silver metal knitting needle gauge in the shape of a bell with different sized holes in the middle numbered from 1-5 and slots around both sides numbered from 6-22. These holes were used as a guide to gauge the size of knitting needles. The numbers and lettering have been engraved into the metal.KNITTING / PIN SIZE / IS WIDTH / OF SLOTShandcrafts, knitting, knitting gauge, george evans collection

Thought to be used for measuring liquids in retail premises by Council Inspectors, Weights and Measures. Used by Shire of Bulla and donated by Hume City Council when amalgmation took place.Tapered metal container with spout and handle used for measuring liquids.on spout "crown/16/91..."shire of bulla, george evans collection

Thought to be used for measuring liquids in retail premises by Council Inspectors of Weights & Measures Department of Shire of Bulla and donated by Hume Council when amalagmation of Councils took place.Tapered metal container with pouring spout and handle used for measuring liquids.on side "1 GALLON" on spout "crown/15 91/VIC"shire of bulla, george evans collection

Cloth sample from an opera cloak made in England c. 1820 from wool clipped from Macarthur's merino sheep in 1816. The cloak was passed down through the family to Harold Lethbridge with whom the main part of the cloak resides, in Narrandera. The fragment was passed to Lethbridge's niece who gave it to the donor's mother who passed it onto him and then it was donated to the National Wool Museum. The cloth fragment was tested by Gordon Institute of Technology in 1974 showing the wool to be very fine (15-16 microns) which is consistent with the pure lineage of Macarthur's sheep. The cloth fragment was framed in 1952 and remains in the original frame to this day. Cloth sample form an opera cloak made in England c. 1820. Wool for the cloak was clipped from John Macarthur’s merino sheep in 1816. Macarthur is recognised as the pioneer of the wool industry that was to boom in Australia in the early 19th century and become a trademark of the nation. Macarthur was responsible for the first bale of Australian wool to be exported. The British woollen mills were desperate for wool at the time because of the Napoleonic blockade, and the Australian bale sold for a record price. Australia needed a product to sell in European markets which did not perish during long sea-voyages and which offered high value per unit of weight. Wool also had a ready market in England because the Napoleonic Wars had increased demand and cut English cloth-makers off from their traditional source of quality wool, Spain. Australia's first $2 banknote featured John Macarthur thanks largely to his establishment of wool as the backbone of the early Australian economy. Red fabric sample folded in half and mounted in the centre of a brown metal frame.'ARCO' MADE IN ENGLANDmacarthur, wool industry, australian economy

The machine was most recently used by donor's father c2008 to knit socks, but had been used for many years earlier. According to family history, it is believed that the machine came to Australia with donor's grandparents in the early 20th century, and was created c1890-1900. It is still in working order and a demonstration was given by the donor during the acquisition process.Griswold stocking knitter machine. Black steel manual machine which clamps on to the edge of a table and is operated by turning a handle. Centre of machine is a cylinder which can be lined with pins to create the sock/stocking. Two detached parts of the machine include a bobbin holder and yarn feeder. Accompanying items include: 3 examples of incomplete attempted socks made by donor. 4 envelops containing instructions, pattersn, notes and advice on using the machine, created by donor's father and grandfather. 1 bobbin with grey yarn. 2 metal machinery pieces. 2 tins containing pins for the machine. 1 metal yarn feeder cone. 10 weights plus two weight stands. Stocking knitter machine has an identifier plate with patent numbers on the side.

At the time of sale, the last of the Hirst family to work in the mill located in Geelong gave Donald (donor Bruce's father) Doherty a set of scales that had been used by several generations of Hirsts and adapted by them over time for specific use in their mill. These Scales were saved from waste and being thrown away at the time of sale to remain in use in the industry in the hands of someone who knew how to use them. The scales were used in calculating the weight of cloth and simultaneously calculating the amount of yarn required to weave it following the instructions printed within the box. The box bears the signatures of two Hirst family members, one being Lewis Hirst dated at 1898. The original brass pole has been replaced with a replica metal somewhere throughout the years after the brass pole broke through use. Hirst was brought by McKendrick in the 1960s and these scales sat for 12 months as part of the 12 month "cooling off" period. The scales were then handed to Donald rather than being disposed of.Scales used for weighing and calculating weight and thread count of textile samples. Originated from Godfrey Hirst Mills in Geelong. Writing describes how to utilise scales. Scales are made from brass, pole for holding scales once brass now replaced with metal pole. Scales held inside wooden box with black text in ink depicting use of scales on paper located inside and outside of box.Outside of box. Wording: APPARTUS for TESTING the WEIGHT per YARD of CLOTHS & COUNT of YARN from a small SAMPLE. -------------------------------------------------------------------------------------------------------------------------------------------------- Indispensable to Manufactures, Merchants & handling Woollen, Worsted, Cotton, Linen, Jute, Hemp, Flannel, Felt, Army, Navy, Police, Railway, Sail & other Cloths -------------------------------------------------------------------------------------------------------------------------------------------------- USED IN GOVERNMENT DEPARTMENTS -------------------------------------------------------------------------------------------------------------------------------------------------- The apparatus consists of Scales, Weights, 1, 2 & 4 sq. inch Cutting Templates & Book of Tables --------------------------------------------------------------------------------------------------------------------------------------------------By weighing a small Sample the accurate Weight in Ounces of a yard of Cloth any width from 18 to 64 inches, the Weight per Square Metre in Grams, the Counts* of Warp and Weft, and the approximate length of full & short ends of pieces of fabrics, [without unrolling and measuring for stocktaking & other purposes] can be ascertained without any Calculation --------------------------------------------------------------------------------------------------------------------------------------------------Price in United Kingdom, 25s., Carriage Paid. Price to Canada & U.S.A. $6.75 do. H. Lord. 10, And Place, Bradford, England. --------------------------------------------------------------------------------------------------------------------------------------------------*When ordering, state on what system you base your YARN COUNTS. Inside of box. Wording: DIRECTIONS FOR USE --------------------------------------------------------------------------------------------------------------------------------------------------TESTING WEIGHT OF CLOTHS. Place sample to be tested on a piece of cardboard, put a Cutting Template on it, cut card and cloth round template with scissors and weigh it according to instructions given in Book of Tables. TESTING FOR YARN COUNTS. Cut out 1 square inch of cloth, draw out wrap or weft threads, according to which is being tested, and the number of inches so drawn, that balance respective weight is the approximate Count. The same rule holds good when number of inches are drawn from a bobbin. In testing from the cloth, allowance has to be made for loss or gain in the process of manufacture. Weight marked C is for Cotton Counts " " W " " Worsted " " " WS " " Woollen Skeins " " L " " Linen Counts. The weights for testing samples of cloth are 20, 10, 10, 5, 3, 2, 1, grains in brass & '5, '3, '2, '1 [tenths of a grain] in aluminium. Inside of box. Signtures, handwritten: Bottom right: Lewis Hirst !898 Top Left (Smudge ?) W Hirst !935godfrey hirst, hirst family, textile design, textile creation

Wrap reel manufactured at Valley Worsted Mill and possibly used in the laboratory. "Wrap reels were used to check the yarn count in a spinning mill. A set length of yarn was wound off several test bobbins and weighed, if the weight was not the correct amount expected the spinning machines draft could be re calculated and the machine draft wheel ( cog ) changed to achieve the required count". - Greg AldridgeA small hand operated wrap reel. The reel is on a wooden base, the winding mechanism is metal and turned by a wooden handle. There is a metal plaque on the base inscribed MAKERS VWM. A wood and metal yarn feeder has broken off its mount.MAKERS/ VWMtextile machinery textile production weaving, valley worsted mill valley worsted mill, warping machinery, textile machinery, textile production, weaving, wrap reel, skein winder

Made for Robur to store their TeaAn embossed plated metal tea caddy which has been painted cream with a blue lid. "It will keep its colour and last a lifetime". Plain rectangle tin painted cream with a blue lid.Robour Tea No 2 Grade net weighttea, caddy, tin

The pram is light in weight. Made of black vinyl with a metal frame. A handle with wooden grips is used to push the pram from behind. It has four spoked wheels with rubber tyres. The hood can be unlocked and folded down as can the handle which folds over the top of the pram body for ease of transport. The pram contains a soft kapok fitted mattress with white heirloom lace frilled cover and a soft pillow covered with a white cotton pillowcase with a chicken and flowers embroidered on it.None

Wool picking machine designed to separate locks of wool before it is carded and spun. The picker opens the wool’s locks which makes it easier to send the fleece through a carding machine. It does this by teasing the fibres (which can also be done by hand just by pulling the lock structure apart), but a picker does this in bulk and much quicker than what can be done by hand. It is possible to spin fibres directly after the picking stage; however, it is usually more desirable to card and blend them with other fibres. Typically, at a textile mill, a picking machine can separate enough lengths of fibre for a full day’s work after just a single hour. It will also help to remove any vegetation matter or other any unwanted elements that may be present in the wool. The quality of the casting on this machine suggest that it was made locally, either in Australia or New Zealand. Mike Leggett, the donor of the machine, acquired it from New Zealand where the seller said it had been used by his father to pick wool to make hand stuffed horse saddles. Mike attempted to used it a couple of times to pick alpaca hair, but the speed of the attached motor caused damage to the fibres. The motor is thought to be an added attachment, sometime around the 1960s judging by its age, while the machine itself is thought to be dated around the 1920s. The machine works by inserting wool through the rollers. Initially there was a conveyor belt feeder system which was powered by the handle on the side. This conveyor belt has been removed however, most likely due to age and deterioration. Wool is now fed through the initial teeth and is met by a spiked rotating drum which works to separate the fibres. The separated fibres would then complete a loop of the drum before being dispatched somewhere below, around where the motor presently sits, at a rapid rate of speed. Typically this wool will be collected in a closet or large catchment area, as can be seen from the 8:47 minute marker in the linked video (link - https://www.youtube.com/watch?v=kMjx-t3tH3A). It is not apparent how the wool is collected with this machine. Red and green machine with four green legs currently attached to a wooden pallet with wheels for easy movement. The green legs lead up to a red central circular barrel from which many attachments are present. Also present on the wooden pallet is a small black motor which is attached by a rubber belt to the central drum inside the red barrel. The belt spins the wooden drum via a dark red circular plate attached to the side of the drum. On the other side of the red barrel, a green handle extends for turning the picker’s conveyor belt feeder system. Two green walls extend forward from the central red barrel, guarding either side of where the conveyor belt would have been. At the start of these walls is a wooden cylinder, which the conveyor belt would have wrapped around, followed by two interlocking gears which rotate and accept the fed wool. The red roof extends over the central cylinder from here, securing the wool inside and protecting hands from the heavily spiked internal wooden cylinder which rotates and separates (picks) the wool. Extending over the top of this red roof is a green handle which reaches to the back of the machine (not pictured). Here it accepts a weight to ensure pressure is always present for the initial feeder interlocked gear teeth. There are two large gear cogs on the rubber belt side of the machine and 3 small gear cogs on the handle side of the machine, all coloured green. A green handle is also present at the rear of the machine, below the location from which the weight is hanging. A power cable extends from the motor and there are two adjustable metal rods on the top of the machine, the purpose of these rods is presently unknown. Black texter. On top of drum. Wording: HG3707 Wording. Imprint: BRACEWIND BLYN On motor. Wording AEIwool picking, textile manufacturing, wool processing

Very large green metal cheese press. Large screwed central shaft with round base and five handles around the circumference. Large round platform at base of press. Chain with weight on one side.Thomas Corbett Maker Shrewsbury| First Prize Cheese Pressrural industry, agriculture

Red tobacco tin 'State Express ready rubbed Virginia tobacco Ardath Fine Cut.' 1 oz. Net weight when packed. Tin manufactured by W.D. and H.O. Wills Australlia Ltd. Sydney. This tin contains small paper clippings from 1940's and 1950's pertaining to Councillor G. A. Pethard. Articles from 'The Bendigo Advertiser.person, individual, mr. george pethard, lydia chancellor, collection, tin, metal, pethard family, mr. george pethard, male, individual, bendigo, smoking accessories, bendigo mayor, person, personal effects

These scales were possibly used at Charing Cross Infant Welfare Centre, Bendigo. A mechanical balance scale. An oval cane basket 60 centimetres long, 38 centimetres wide and 13 centimetres deep sits on top of the scales. Two metal bars two centimetre wide and half a centimetre thick, underneath the basket hold it on the scales balance mechanism. On the other side of the balance mechanism is a 20 centimetre by 12 centimetre and one centimetre thick metal plate on which the known weights are placed. The base of the scales is a moulded metal consisting of two half domes 14 centimetres diameter and six centimetres high joined together by a ten centimetre long, four centimetre wide and six centimetre high section.4LB 14OZ 3JI CIII C2320baby scales, charing cross infant welfare