Known as Powerlot, built by George Packer, a local builder for Jim McLaughlin in 1914. During Olsen family ownership house was altered. The two acre site once had landscaped garden and orchard. Flat roof has lead lined walkway for viewing lakes and sea. Story goes 'The German raider Wolf was observed signalling during WW1'.Colour photograph of a white painted timber dwelling set on a high vantage point at Stirling Road consisting of two wings, one with flat roof and veranda on three sides, the other more recently built has hipped roof. Metung Victoriahouses, tourism, heritage study

Bell used by the conductor to signal to the driver to stop, proceed or an emergency stop. The flat leather strap indicates it was used on a cable tram, rather than an electric tramcar which were fitted with round leather cords. The leather strap is riveted to a round steel ring.Demonstrates a conductors communication or signal bell made for use on cable trams.Brass Conductor Communication Bell, or signal bell, consisting of cast frame, bell striker and bell pull part. Has at both ends, four open screw holes that were used to secure the bell to the roof of a tram with a flat 22mm wide leather strap attached using a steel ring.trams, tramways, conductors, bells, cable trams

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The screws on the side adjust the flame and hence the strength of the flame produced. Prior to the introduction of gas and electricity these lamps provided lighting in all householdsPioneers and early settlers in Moorabbin Shire relied on kerosene lamps for lighting their homes after sunset.This kerosene, flat wick, banquet lamp has a clear glass shade chimney with a frilled rim, a reservoir of plain yellow glass and a metal engraved base . 1 side screw to adjust the flamelights, early settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, cheltenham. lamps, kerosene, paraffin, oil

The Baranduda and District School Sports Association held its first interschool sporting competition in 1936. Schools included in this association were Allan’s Flat, Bonegilla, Baranduda, Leneva, Mitta Junction, Staghorn Flat and Wodonga West. This commemorative trophy, The Thomas Chubb Shield, was donated to the Sports Association by Mr. Albert John Chubb, in memory of his father. Mr. Thomas Chubb was a successful businessman in Albury and an active supporter of many institutions and community organisations in the Albury Wodonga area. Mr. Albert Chubb actively supported school sports carnivals across the district, including being the official starter at many events.This trophy has local social and cultural significance as it provides evidence of sporting and social interaction between the small schools in the Wodonga and surrounding communities,A wooden shield presented to recognise winners of the Baranduda and District School Sports Association from 1936 to 1949. A metal hanger is attached to the top.On top metal banner "THE THOMAS CHUBB SHIELD" . On central shield "BARANDUDA /AND/DISTRICT/ SCHOOLS/ SPORTS ASSN. On small shields from top to bottom, "LENEVA 1936/ BONEGILLA 1939/ LENEVA 1941/ LENEVA 1949/ LENEVA 1948/ LENEVA 1947/ ALLANS FLAT 1940/ MITTA JUNCTION 1937"baranduda sports association, school sports, wodonga district, thomas chubb

These survey plans are a useful research tool.A flat green fabric folder with a white label with "SNOWY RIVER FLATS" hand-written in black. It contains plans.plans-survey snowy-river-flats department-crown-lands-victoria

An oar is an implement used for water-borne propulsion. Oars have a flat blade at one end. Rowers grasp the oar at the other end. The difference between oars and paddles is that oars are used exclusively for rowing. In rowing the oar is connected to the vessel by means of a pivot point for the oar, either an oarlock, or a hole. The oar is placed in the pivot point with a short portion inside the vessel, and a much larger portion outside. The rower pulls on the short end of the oar, while the long end is in the water. By contrast, paddles, are held in both hands by the paddler, and are not attached to the vessel. Rowers generally face the stern of the vessel, reach towards the stern, and insert the blade of their oar in the water. As they lean back, towards the vessel's bow, the blade of their oars pivots in the oarlock, and the end in the water moves towards the stern, providing forward thrust. There also is another way of propelling a small craft it's called a sculling oar which is attached to the transom and used to propel a small vessels rather than using two oars as previously described. It is believed the subject item is just such an oar given it’s long blade associated with a sculling oar. For thousands of years vessels were powered either by sails, or by the mechanical work of rowers, or by paddlers. Some ancient vessels were propelled by both oars and sail, depending on the speed and direction of the wind. Wooden oars, with canoe-shaped pottery, dating from 5000–4500 BC have been discovered in a Hemudu culture site at Yuyao, Zhejiang, in modern China. The history of man using wooden oars to propel a boat has a considerable record in marine archaeology going back many centuries. The item is significant for marine archaeology as it gives a snapshot into how a small row boat was powered using a wooden sculling oar. A method of propelling a small boat still used today an example is the gondoliers in Venice using a sculling oar in a circular motion to propel his craft. Single sculling oar with long flat blade, two copper bands, on blade with rowlock fittingNoneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, boat oar, sculling oar, row boat

Iron was heated on top of stove. Often the person ironing had two irons - one to iron with and the other heating on stove ready to use when the other cooled down. They were heavy to use and were generally cleaned with bees' wax and a cloth before use. Wooden handles were patented in 1865.This item is an example of a domestic appliance in common usage before the advent of electricity.Small rusty flat iron.domestic iron flat-iron

Spokeshave wooden flat handled flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Flat screwdriver 450mm long.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Domestic Flat Iron Stand stawell

Used by horse rider for control of horse and safe movements of horseManufactured and retailed by Holden and Frost Ca 1900Horse shoe shaped metal with a flat base to support foot of rider. Base is flat with hollow spaces. Painted blackstirrup, equine

As part of the push to cut electricity costs and diversify supply, the Victorian Government (circa 1930) implemented the conversion strategy from mainly brown coal supply to hydro - electricity. The Kiewa Hydroelectric Scheme became the largest scheme of its kind in the State Of Victoria and the second largest scheme in Australia. Clover Dam and Power Station were built by the State Electricity Commission of Victoria as part of the Kiewa Hydro Electric Scheme from the late 1930's to the early 1940's. This dam was constructed to supply water to feed four turbines (62 mega watts) at the West Kiewa Power Station. This was at the forefront of sustainable "Green" energy. Costs associated with power supplies is still a major incentive of governments, however environmentally friendly alternatives such as wind and nuclear have also made inroads. The Kiewa valley and its surrounding alpine catchment were looked at(Victorian State Government), from the beginning of the twentieth century as a source of alternate power for an ever-increasing demand for electricity by growing population and heavy industrial areas within Melbourne City and State regions. Construction of dams, such as Clover Dam provided the large quantity holding areas of water required to turn the turbines at the various power stations to provide the electricity needed. The impact of these controls by moderating water run-off from the alpine regions is beneficial in reducing flooding from thawing of snow on the alps. This by-product allows agriculture and grazing to be less vulnerable to seasonal flooding thereby resulting in a more stable annual production level.Black and white photograph of Clover Dam buildings and Kiewa River. Has a .4cm white border around photograph Printed on bottom left corner of photograph in white - Clover Flatclover dam, secv

Joan O'Shea Collection. Bendigo Swap Meeting Souvenir Guide 1987 Booklet. 74 PagesPrinters J.J. & D.V. Mulqueen, Kangaroo Flat. Vintage Vehicles.bendigo, tourism, bendigo swap meet

This is the first iteration of a pharyngeal tube devised by Hewitt in 1913.Round metal tube with a brown rubber tubing sleeve around the outside.Engraved on flat portion of metal tube: MEDICAL SUPPLY / LONDONfrederick hewitt, pharyngeal, intubation, medical supply, london, alfred hospital, melbourne

Racing green cardboard box with cardboard slide tray holding three needles. There is allocation in the slide tray for twelve (12) needles. There is a white manufacturer's label on the front of the box.Stamped onto the flat of each needle: NON / STAIN / STEELhypodermic, needle, syringe, empire

Penleigh Boyd, Robin and Patricia Boyd's son, writes “Prior to 1950 Robin, like most other amateur or hobby photographers, took black and white printed photographs. The oldest slides date from 1950 when Robin and Patricia travelled to Europe on Robin’s Robert Haddon Travelling Scholarship.” In 1948 Robin Boyd was awarded ‘joint first place’ in the Robert Haddon competition for his design of Mildura art gallery. The scholarship helped fund their first overseas trip. Robin and Patricia were passengers on the Greek ship “Cyrenia” departing in May 1950, passing through the Suez Canal and landing in Genoa five weeks later. For six months, they travelled extensively throughout Europe (predominantly driving themselves) - France, Italy, United Kingdom, Sweden, Denmark, Germany, Austria, Switzerland and Spain.Colour slide in a mount. Social housing, New Empiricism style, Stockholm, SwedenStockholm / N-E / Flats-New Empiricism (All Handwritten)haddon travelling scholarship, haddon, robin boyd, slide

This flat hinge was recovered from an unknown shipwreck in the coastal waters of Victoria in the late 1960s to early 1970s. It is part of the John Chance Collection. The size of the hinge indicates that it was used for a large item such as an entry door, gate or perhaps a ship fitting. The blue-green patina on the metal is caused by a reaction from its exposure to external elements such as the sea water. The hinge is likely to have been in the water for over 100 years, as the more widely known shipwrecks along Victoria’s Shipwreck Coast date from 1837 to 1940. Before the Middle Ages metal was expensive and took a lot of effort to work with As time went on, methods were discovered for working more easily with metals, and ways were found for combining different metals to make alloys that made the metals stronger and more durable. Hinges forged by blacksmiths began to be common in homes. In the Victorian Era steam power was introduced and manufacturing boomed. Hinges could be made by machines quickly and in great number. All sorts of applications were found to take advantage of the features of hinges. They continue to be developed and used in a huge variety of ways. Although the hinge is not linked to a particular shipwreck, it is recognised as being historically significant as an example of hardware either as part of the ship’s fittings or imported for use in Colonial Victoria in the 19th to early 20th century. The hinge is also significant as it was recovered by John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several wrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value. Hinge; heavy bronze flat hinge, hand forged. Flat with narrow, arrow shaped end that lares outward to wider straight end. Attached to the wide end is a rectangular, upward curved knuckle. There are five formed holes along the hinge, two are oval shaped and three are round. The hinge has a blue-green patina.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, john chance, hinge, hardware, flat hinge, door fitting, ship’s fitting, 19th century metalwork, forged hinge

The photo was taken on ANZAC Day 1985 at the Kangaroo Flat RSL service with Bill Forrest leading. William (Bill) Malcolm Forrest was born in Moora WA, enlisted 12.4.1951 No 5/1788 age 18 years and became a Sapper. After attending Battle School in Japan he then served with 3 RAR in Korea, DVA file states 12.7.1953 to 15.7.1954. He later went on to serve with 2 RAR in Malaya. He was discharged after 6 years service on 11.4.1957, discharge certificate states Active Service being 1 year 337 days. He re enlisted again on 11 3.1958 with Regt No 36283 and served another 17 years 165 days and was discharged with the rank of Sgt on 22.8.1975. During this engagement he had Corps and Trade Training 6 months, Regimental, Steward, Army Mess Supervisor and General Duties with Training and Survey Units.Photograph B & W showing a group of men marching in an ANZAC Day Parade. The man leading carrying a flag is Bill Forrest from Kangaroo Flat RSL.photographs, anzac day, korea, malaya

A sledge hammer is generally wielded with both hands and is used for driving wedges and posts and for other heavy work. It can be used to remove concrete slabs, to drive heavy steel bolts into concrete, to hammer large stakes as well as for demolition.This item was a common tool used by farmers or blacksmiths.A large flat hammer with a wooden handle.Underneath hammer - 10hammer sledge-hammer tool

Flat screwdriver no handle 265mm longflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Replica WW1 Naval Flat Topheadgear, ww1, ran

3BO radio mast, Myers Flat.slide, bendigo, 3bo radio

flat box spanner, surface rustJENBRObox, spanner, tool, tools, churchill island, farm

Cast iron flat iron, with handle.Markings on top of iron - the number 6, Silversters patent and Salter and scroll work.irons, flat irons

Used at Camp 13, Italian compound, Murchison. Recovered from there in 1989. Iron would have been heated before use on a wood fired stove top/hot plateBlack flat iron with shaped handleiron, camp 13, murchison, tatura, domestic, items, irons

Robin Boyd has written 'Australiana' on the slide mount (item S1081) at the same location. Robin Boyd was always on the lookout for signage and blots on the landscape, especially when writing and illustrating his 1960 book, “The Australian Ugliness”.Colour slide in a mount. Flats, AustraliaMade in Australia / 13 / AUG 65M / Encircled 2 (Handwritten) / Australiana 2 (Handwritten) / 10 (Handwritten) / Encircled 2 (Handwritten)australia, slide, robin boyd