Drawing details brake rigging and dimensions for a Brill 22E truck. Dated 4/8/1947, prepared by the SEC Geelong branch, signed by H N Hornabrook 6/8/47 showing the layout and loads on each part of the brake system, drawing No. T1647. See item 9025 and 9857 for other versions.Yields information about the brake rigging for Brill 22E trams and demonstrates the activities of the SEC Geelong office.Drawing - blueprint, titled "Brake rigging dropped centre double bogie tram Brill maximum traction truck 22E, Trams Nos. 31,""D1775" in ink on top sheet right hand corner.brill 22e, drawings, brake rigging, geelong

Drawing detailing the brake rigging, dimensions, equations and forces for a Brill 22E Maximum Traction Truck. Prepared by the Geelong office of the SECV 1949, signed by Mr Hornabrook. See also item 9025. Yields information about Brill 22E brake rigging and equipment.Digital image of a drawing.tramcars, brill 22e, brakes, brake rigging, geelong

Set of three drawings related to the Brill 22E Maximum Traction trucks: 1 - "Brake Rigging Brill Maximum Traction Truct No. 22E" - showing the dimensions of the levers and pivot points. For the relevant Geelong drawing T1647 see item 8044 and 9025. 2 - "Standard Pony Axle" - traced from MMTB drawing R3755 3 - "Pony Axle Box" - traced from MMTB drawing R1112 and dated in ink 28-4-1955Yields information about Brill 22E brake rigging and equipment.Set of three Drawings - dyeline print on plain paper with a brass clip in the top right hand corner.tramcars, brill 22e, pony axles, axles, axle boxes, brake rigging, ballarat, geelong, drawings

Produced by Melbourne Electric Supply Company Limited (MESCo), Geelong Branch for the Geelong Tramways. Drawn 21/03/1930.Retraced from original document showing in good detail, three views of the Brill Radiax Truck (E1B Special) with specific shewing details of the brake rigging.MESco (Geelong Branch) document GE-T7-7630; "Brill Radix (E1B Special) Truck Shewing Details of Brake Rigging.". Drawn 21/01/1930. Redrawn from the original dyeline print.Redrawn from the original dyeline print.geelong, geelong tramways, melbourne electric supply co. ltd., mesco geelong

Instruction - 3 pages - duplicated foolscap sheets - headed "MMTB Engineering Department - Workshops and Running Shed Branch" - titled "Running shed Pitman" Details duties of Pitmen at depots, in adjusting brakes, oiling bearings, training, responsibilities, training, driving of trams and other tram maintenance work. Dated May 1970.trams, tramways, depot, safety, workshops, pitmen, instructions, procedures, brake rigging, training

Instruction - 5 pages - duplicated foolscap sheets - headed "MMTB Engineering Department - Workshops and Running Shed Branch" - titled "Pitman Duties" Details duties of Pitmen at depots, in adjusting brakes, oiling bearings, training, responsibilities, inspections, packing of bearings, inspections, hot axle boxes, changing of trucks and general maintenance. Dated May 1970.trams, tramways, depot, safety, workshops, pitmen, instructions, procedures, brake rigging

Drawing of the brake system on a Melbourne W3 tram. Drawing R5956trams, tramways, mmtb, braking, w3 class, brake rigging, brakes

Photograph of an Melbourne Tramway and Omnibus cable tram showing the axle box, springs and wheel supporting the body of a trailer. Shows the side skirts around the wheel. Part of the brake rigging can be seen as well.Yields information about cable tram trailers wheel sets.Black and white photograph on paper. Two copies held.trams, tramways, mtoco, cable trams, trailers, wheels, axle boxes

Drawing titled "No 2 end brake lever" showing a part of a Brill 21E truck, shows the positioning of the holes for other parts of the brake rigging. Would have been used at the depot or the SECV Workshop for the drilling of a plate. Item undated.Yields information about the position of the drill holes on a brake lever fitted to single truck trams.Hand drawn drawing in pencil on plain quarto sheet.tramcars, equipment, rolling stock, brakes, brill 21e

Set of 26 photographs of the "Brill 21E truck" without motors or brake rigging arriving in Canberra from Bendigo Tramways on 20/6/1991 and placed under the body of Geelong tram 28. See item ?? for other photos of the event. The tram was first lifted out of position, the truck placed on the ground, and then the tram was placed on top, alongside the body of Geelong No. 2Yields information about the fitting of a "temporary" or cosmetic Brill 21E truck to Geelong tram No. 28 when it was in Canberra.Set of colour negatives placed in a sleeve"Truck arriving No. 28"geelong, tram 28, canberra, brill 21e, 21e trucks, tram 2

Paper by Dudley Snell, MMTB Chairman, read to the Hong Kong Section of the Institute of Engineers in 1986, titled "The Melbourne Tramway System - Some Reflections", looking at the history and practice of tram track construction in Melbourne from cable tram days to the 1980s methods. Has diagrams of the various types of track used, rails, sleepers, concrete, joints, slab depth, drainage, rail type, BHP rolling of grooved rails, alternatives to grooved rails, and the impact of thermite welding on joint noise. Noise issues addressed through resilient wheels, brake rigging, use of moulded composite brake shoes, the development of the Kirby joint, Yields information the Melbourne tram system and demonstrates the type of information retained about the tramway system.Set of nine A4 sheets photocopied. Has been stapled in top left hand corner.trams, tramways, melbourne, history, ptc, mmtb, track construction, new track, thermit welding, kirby joint

Demonstrates aspects of the Ballarat Tramways following the end of the 2nd world war - when the tramway traffic was still high peak. Gives details of working hours, rosters for the week of motormen. Shows the additional trams to the basic service on Weekdays and hours of one man operation.Single large typed sheet of paper, titled SECV, Electricity Supply Department - Ballarat Branch, Ballarat Tramways, "Motorman's Runs with daily rostered hours". Arranged with four main columns, Monday to Thursday, Friday, Saturday and Sunday and within each main column 9 further columns giving Run No, Take Up, Relief times, Ord Rate (hours), One Man Rate, Spread (always "-" except for two on Saturday). Sign On and Sign Off - either 10 or 15 and the Total Hours. Columns vertically ruled in red ink. Not dated, but preparation format aligns with 3418 - 11/10/1946 - assume 10/1946. On rear in pencil is sketches for brake rigging components. In top left hand corner in black ink "B.T.P.S. Cat No. 801"trams, tramways, ballarat, rosters, employees, shifts, timetables

Black and white photograph of cable trailer 88 being loaded onto a wagon at the Spencer St / Flinders St railway yard by the railway yard travelling gantry crane. Trailer lettered M&MTB. Has a man riding the top of the car before being loaded into a I type open wagon. Photo mid to late 1920s? Photo from the Collection of the Department of Infrastructure now with the Public Records Office - image number "Box 108-1. Note: this photo is now out of copyright and may not have been an original VR photograph, but one copied from another source and collected as their Heritage series. The building in the background in Flinders Street (extension/west.) is the former Melbourne Harbour Trust Officers. By the time of this photo was taken the building was in the hands of the Department of Agriculture. Their name can just be seen on the top part of the building. It was demolished when the convention centre was built beside the WTC in the mid-1980’s. The crane was dismantled in the late 1990s around the time of the No 1 goods shed was moved to Bylands. The cable car has been stripped of a number of parts : Some windows. All the brake rigging and pawls All the roof-mounted destination boxes. The wheel skirt.Shows how redundant cable trams were sold and transported to country locations.Photograph - Black and White - Loading cable car trailer 88 at Spencer StHas Department of Infrastructure copy right stamp on rear and number "Box108-1" in ink on rear and "1-8"tramways, trams, cable trams, flinders st, sale of trams, railways, tram 88

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 216 NQR - Open Medium Truck 15/ 1/1914 NWS Built new VR Service History *NQR 216.VA - 15/ 1/1914 NWS Built new - / /1926 - To NQ 216.VA - Puffing Billy Service History or Notes April 2016 - Trial fitting of brake rigging May 2016 - Riveting of the draw gear castings in progress July 2016 - Riveting of the draw gear castings in progress. Truss rods threaded ready for fitting Aug 2016 - Rivetting of the draw gear castings in progress. Draw gear and couplers being evaluated. Sept 2016 - Riveting of the draw gear castings in progress. Draw gear and couplers being overhauled. Oct 2016 - Riveting of the draw gear castings completed, brake piping installed. Nov 2016 - Floor installed, under framing welding completed, fitting of side doors, hand brake fitted Dec 2016 - Car Workshop - Side panels fitted, end panels to be fitted Jan 2017 - Couplers fitted, brake rodding connected, transferred to Emerald for bogie work and sign writing. Feb 2017 - At Emerald - Tyres machined, braking system being prepared Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck216 NQR - Open Medium Truck made of Steel and metal216 NQRpuffing billy railway, pbr, rolling stock , 216 nqr - open medium truck, victorian railways, nqr - open medium truck

Manual - 176 quarto pages + light grey covers Electrical" on a cover pages. with a red comb binding. Prepared by Donald G Curry of the Seashore Electric Railway, 17/6/1962. Document has table of contents: Covers Painting, Roof repairs, body repairs, inspections, Lubrication, Traction Motor Maintenance, controllers, hand operated circuit breaks, car resistors, traction braking equipment, trucks and rigging. Has an appendix and index. Document has been scanned. Part 1 - cover to page 17 2 - pages 18 to 40 3 - pages 41 to 66 4 - pages 67 to 100 5 - pages 101 to 132 6 - pages 132 to 159 7 - pages 160 to rear cover trams, tramways, manual, tramcar equipment, maintenance, motors, controllers, tramcars, tram bodies