A bulkhead no. 69 that has a metal plate number 69 underneath golden plate with texts"HMAS Vendetta Sept 69 - Oct 71 Bulkhead number" on a standing wooden boardHMAS Vendettahmas vendetta, bulkhead

Serial No. S293-1 I/R 94132

This ES Ka6 sailplane (VH-GRW, serial number 55) was built under licence from Alexander Schleicher in 1962 by Edmund Schneider Limited. It was one of 12 Ka6s, with minor variations from the Schleicher product, built by Schneiders in Australia. It was test flown at Parafield Aerodrome, Adelaide, on 8th September 1962. By way of background, the Schleicher KA 6 series of sailplanes were designed by Rudolf Kaiser in Germany. They were quite successful in the Standard Class in the late 1950s and 1960s. Over 1400 were produced. The first owner of VH-GRW was the Victorian Motorless Flight Group which, at the time, was based at Berwick Airfield on the outskirts of Melbourne. On 22 April 1972, the ownership passed to a syndicate of members from the VMFG. It again changed ownership in July 1974. The new owners were another syndicate based at Campbelltown in New South Wales. The glider went to a Tasmania syndicate in June 1976 and finally to the Soaring Club of Tasmania. In total VH-GRW recorded 3369 hours air time from 4952 launches. It was used very little after 1996. This exhibit is an example of the Scheicher Ka6 sailplane type that were built by Edmund Schneider in Australia.Plywood, spruce and fabric covered high wing single seat sailplane. The airframe has been restored to the point of repainting. Currently the fuselage, rudder and the wings aft of the main spar are coated with pink dope. The tailplane retains the white gloss finish of the glider prior to the restoration work. The cockpit to be refitted (with instruments etc). Serial number 55. The manufacture details are displayed on a metal plate fixed to the main bulkhead. australian gliding, glider, sailplane, schneider, schleicher, ka6, rhonsegler, victorian motorless flight group, soaring club of tasmania

Yields information about the appearance of BTPS trams at the time of the first COTMA conference in 1975.Agfa colour slide, white blue plastic mount. Photograph Friday 25/4/1975 at the time of the first COTMA conference. Photo of the interior of one of the single truckers showing the signs in driver's bulkhead and used ticket box. Photo by David Verrier.On back of slide in ink' "Friday 26/4/75, Interior 40 Ballarat"tramways, trams, btps, interiors, signs, tickets, cotma

Photo shows one of the Maximum Traction Bogies trams built for the Hawthorn Tramways Trust by Duncan and Fraser of Adelaide in 1917-1918. Photographed in the Hawthorn Depot some time before May 1925. This tram began its life as HTT No. 30. The body was sold in 1944. The full photo appears on page 17 of Tramway by the River.Yields information about early liveries of MMTB ex HTT bogie trams.Two photos of former HTT bogie tram No. 136 at Hawthorn Depot before May 1925. On rear of photo 1, it is noted that the paintwork was that before May 1925. Other notations (1) Long piece of barrier rail along drop centre (2) Monogram (HTT) on saloon doors (3) Triple railings over bulkhead windows (4) Cylindrical destination box (on rear). Notes on photo 2, (1) paintwork was that before May 1925 (2) Route No D (3) Monogram (HTT) on saloon door (4) Triple railings over bulkhead window (5) Old destination box (6) Iron gates.See notes above.tramways, trams, hawthorn depot, tram 136, mmtb, htt, p class, route d

Digital image of Tram 36 outbound in Lydiard St Nth - side on view crossing an intersection. The conductor can be seen selling tickets, leaning against the drop centre bulkhead. Photo by Peter Knife 20/10/1970. Yields information about Ballarat's trams in October 1970.Digital image of a colour slide.tramways, tramcars, ballarat, lydiard st nth, conductors, tram 36

Used by the MMTB to indicate to conductors and inspectors, the tramcar number. Placed on the driver's bulkhead, facing into the tram with one at either end of the tram. The tram was built by Holden's Bodyworks in Adelaide, entered service in April 1926 and was disposed of in Oct. 1967.Demonstrates the method of advising crews the tramcar number internally.Set of 2 signs - galvanised rectangular sheet steel - provided with four screw holes, one in each corner painted with the numerals 3, 3, and 0. Both have small pins - one on the lower edge and one on the right side.signs, trams, tramcars, tram 330, w2 class

Used by the MMTB to indicate to conductors and inspectors, the tramcar number. Placed on the driver's bulkhead, facing into the tram with one at either end of the tram. The tram body was built by James Moore of South Melbourne entering service in 9/1924. It was sold in 1979.Demonstrates the method of advising crews the tramcar number internally.Aluminium sheet rectangular, with screw holes in each corner painted with numbers, 2, 5 & 4.trams, tramways, tramcars, tram 254, w2 class

Black and White Photograph of TMSV workers replacing the canopy roof on the bulkhead of cable tram 256 during restoration work - replica horse tram 256. Taken by Keith Kings 22/12/1974. .2 - has been masked by paper to crop the image. Has number (21A) in the top right hand corner.On rear in ink detail notes see image i3 and notes on the other print with number 27-1.trams, tramways, tmsv, horse trams, cable trams, tram 256

Poster - blue background with a colour image of a conductor pointing to the sign wording in black or red print. Titled "Its your responsibility to hand fare to the Conductor before leaving car". Refers to By Law 5, with a penalty of five pounds. Poster has been adhered to a sheet of glass that was backed with a sheet of brown paper. The glass was used in the driver's bulkhead of a W class tram.trams, tramways, mmtb, by laws, conductors, tickets

Poster - white sheet of paper, titled "Time table of Sunday Morning Tram and Bus Services", providing details of the tram and bus services for September 1953, from first tram (about 8am through to about 2pm). Signed by F. G. Wraith as Manager. Poster has been adhered to a sheet of glass that was backed with a sheet of brown paper. The glass was used in the driver's bulkhead of a W class tram.trams, tramways, timetables, sunday services, mmtb

Smiths began with a craftsman named Samuel Smith who in 1851 opened a shop in Newington Causeway, London, where he made and sold watches, clocks and precision instruments. Samuel had a son, Samuel Jnr who was apprenticed in his fathers business. Samuel Jnr eventually opened his own business at 85 Strand and later opened other premises at 9 Strand, Trafalgar Square and 68 Piccadilly. In 1899 he turned his business into a private limited company, S. Smith & Son Ltd. Samuel Jnr son, Sir Allan Gordon-Smith, joined him as Manager at 9 Strand in 1903 and laid the foundation of the vast Smiths organisation of the future, leading the company towards the supply of accessories for the then developing motor industry making car clocks and the first speedometers patented in 1904. In July 1914 a new company was formed under the name S. Smith & Sons (Motor Accessories) Ltd., to take over the motor accessory business of S. Smith and Son Ltd. and this became the main company of the group which eventually grew to become Smiths Industries Ltd. The original company S Smith and Sons Ltd., continued as jewelers and clock and watchmakers until 1930 when the company was taken over by Bravingtons retail jeweller chain. In 1931 Smiths decided to enter the domestic clock market and formed a new company, Smiths English Clocks Ltd., as the Clock and Watch division of S Smith & Sons (Motor Accessories) Ltd. This is the start of "Smiths Clocks" because this is when they began to manufacture domestic clocks in quantity. Moreover, they set out to produce these clocks at a price that the average householder could afford. S Smith & Sons (Motor Accessories) was at this time was the main company in the Smiths group of companies and their business developed both in the motor vehicle field and outside it. Smiths began to make automatic pilots for aircraft and, through the acquisition of a majority interest in Henry Hughes & Sons Ltd., entered the field of marine instruments. During the war from 1939 to 1945, Smiths' production expanded. There was a demand for motor, aircraft and marine instruments for the Services and the production of industrial instruments and it is at this time that our item was made. In 1944 many changes were made to the Smiths' organisation. The name of the principal company was changed from S Smith & Sons (Motor Accessories) to S. Smith & Sons (England) Ltd. and four new subsidiary selling companies were set up. These were Smiths Motor Accessories Ltd., Smiths Aircraft Instruments Ltd., Smiths Industrial Instruments Ltd., and Smiths English clocks Ltd. The manufacture of clocks and watches ceased in 1979 and 1983 saw Smiths withdraw from producing items for the motor industry.An item that is now regarded as a vintage, sought by horology collectors worldwide and is in excellent condition. The item is unique in that it was made specifically for ships by the Smith company a well known British clock manufacture. Its provenance is well established and it was made during the world war II era specifically for merchant and naval vessels of the time. Naval brass ships bulkhead clock. The clock face is of white enamel with black Roman numerals, an outer minutes ring and black steel hands. There is a subsidiary seconds dial with sweeping hand just above the centre and a fast/slow adjustment lever above that. There is no manufactures name on the dial. There are a beveled glass and brass hinged lid to the front of the clock. The clock is housed in a heavy brass case with screw holes around the circumference for mounting. There are no markings on the clock or mechanism flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, s smith and sons, clock, maritime clocks, clock makers, bulkhead clock

The Hall Cherokee II glider is an American design for amateur construction from plans. The designer was Stan Hall (1915-2009), a professional engineer, who gained extensive experience in the United States aviation industry during World War 2 including the programs for military gliders. He continued to work as an engineer for aircraft manufacturers and as a consultant to the industry after the war. He was active in gliding and, in particular, the home built sailplane movement. The Cherokee II was one of about 10 glider designs that he produced: it came out in 1956. It is understood that over 100 Cherokee gliders have been built. In Australia the number is possibly 10 or 11. The Hall Cherokee VH-GVO was built by R.D Meares of Caringbah, New South Wales. The glider was registered as VH-GVO on 11 October 1973 and given serial number “GFA-HB-82” by the Gliding Federation of Australia. The Logbook for VH-GVO appears to be a complete record of the flying history; in aggregate 210 hours 40 minutes in the air from 331 flights. The first test hop occurred on 29 July 1972 at Camden, New South Wales. VH-GVO was last flown on 22 July 1986. Many of the flights recorded are of one or two hours duration. The glider was last inspected and certified as airworthy and in a reasonable condition at the Hunter Valley Gliding Club in July 1986. Since that time, until transferred to the Australian Gliding Museum, the glider was in storage. Structural restoration work has been completed on the fuselage and one wing. However, inspection of the other wing revealed extensive damage to the ribs and spars and consequently a decision was taken to make it a static exhibit. The exhibit is an example of home built construction of a type that has proved popular amongst amateur glider builders.The Hall Cherokee (formerly registered as VH-GVO) is a single seat wooden home built glider. The glider is constructed from wood, plywood, fabric and metal fittings, all commercial grade except for main wing fittings, pulleys, cables and bolts. The fuselage is simple with four main longerons and bulkheads with diagonal bracing. The wing has two identical solid spars which form a geodetic structure, hence the leading edge is non-structural. Registration VH-GVO – serial number GFA-HB-82 australian gliding, glider, sailplane, hall, cherokee, meares, hunter valley gliding club

Series of B&W photos of the interior and some exterior lettering and lining of Horse tram No. 1 showing the as received condition of the tramcar body. 790.1 - end panel bulkhead and cut hole through the roof where a cupboard was placed - see also item 766 for other details of the By-Laws signs. 790.2 - photo of tramcar side showing the outline through the paint of the tram car number - "1" 790.3 - Interior photo showing detail of framing around the By-Laws signs - see 766. 790.4 - interior detail where roof and end bulkhead meet. 790.5 - Exterior - showing some details of the lining. 790.6 - Exterior - showing locations of lettering along the base of the sides - have been outlined with a heavy line to show layout of lettering. 790.7 - as above but close up of "LLAA" 790.8 - similar to 790.4, but closer up. 790.9 - Exterior - view of one of the bottom corners of the body, showing the steel framing and the lining through the paint.trams, tramways, horse trams, btps, reconstruction, tramcars , tram 1

Poster - white sheet of paper, titled "Notice to Passengers - Conditions Governing the Carriage of Small type baby carriages, shopping pushers, golf club buggies on trams during Certain Hours". Signed by F. G. Wraith as Manager. Dated Feb. 1953. Provides details of times, fares and where on the system. Poster has been adhered to a sheet of glass that was backed with a sheet of brown paper. The glass was used in the driver's bulkhead of a W class tram.trams, tramways, mmtb, prams, tickets

Set of four drawings, photocopy reduced to A3 size of the "Concept drawings re modifying W class circa Dec. 1988". Shows the introduction of a front door step, relocation of controls, bulkheads, changes to windscreens, introduction of a formal seat for the driver. subtitle - "Modified 'W' class", was proposed to be the W8 class at the time Date 1988, see Reg item 1970 for concept memorandum and 8789 for a working party set of notes. Second set added 8/3/17trams, tramways, w class, overhauls, preston workshops, drivers, w8 class

Photograph of one of the three Victorian Railways "Luxury" cars that were sold to the MMTB following the closure of the final section of the St Kilda - Brighton tramway on 28-2-1959. The tramcar has been placed on No. 15 trucks to enable movement around the workshops. Two of the trams, No. 52 and 53 were modified with longer running boards, full driver's bulkheads to replace the blackout blinds, route number boxes, removal of the red oil lamps above the headlight, conversion to from Broad gauge (5'3") to standard gauge, changes to destination boxes, seating and many other changes. Reference Destination City, Edition 5, page 103.Yields information about the former VR "Luxury" trams sold to the MMTB in 1959.Black and white photograph of one of the three Victorian Railways Trams sold to the MMTB at Preston Workshops.tramways, mmtb, trams, victorian railways, st kilda brighton electric tramway, preston workshops, vr class

Set of three Photographs, Black and White, of the interior of SW6 850, showing the interiors of the tramcar, one showing the view from the drivers door and the other of the drop centre area. Shows the highly varnished seats in the drop centre or smoker area. See also Reg Items 674 and 3425 for other photos, probably taken at the same time. Two copies held of item 3. See Reg Item 3558 for another print within an album.In ink on the rear: Copy 1 - M&MTB SA 949, SW6 850, Interior 1939, Note: Loud speakers in rear bulkhead, plywood smoker seats, South Melbourne depot. Copy 2 - M&MTB SA 950, SW6 850, Interior, as above. Copy 3 - as above but notes the speaker was later removed and number SA26 Both prints have the photographers stamp and date stamped 12 Jan 1946.trams, tramways, sw6 class, interiors, new trams, tram 850

The Ada is a barge made of a composite of wood and iron. it was built at Echuca in 1899 to carry wool and cargo from station properties on the Murray and Murrumbidgee rivers to the Port of Echuca . It was towed along the river by paddle steamers, mainly The PS Pevensey. The Ada could carry 350 tons of cargo and was originally owned by The Permewan and Wright, Murray Shipping Co. In the late 1930s she was bought by the Evans Brothers' Red Gum Sawmill. Two bulkheads were removed to enable the logs, to be placed inside and transported to the mills. Road transport overtook the use of the river barges, and The Ada was left abandoned on the banks of the Murray River opposite the sawmill until it was purchased by the Port of Echuca in 1974 and refloated in 1979.A barge with a composite hull of steel and timber which was built in 1898ADA signage on port and starboard bow

Yields information about the interior views of the Ballarat tramcars and the driver's compartment.Six (6) Digital images taken by George Coop during the period 1968 - 1970, of the interior of trams. .1 - looking out of the open windows of a the saloon of a single trucker to the tram 28, at the City terminus. There is an Australian Symphony Orchestra interior advert. .2 - Looking through the open passenger door, with No. 17 behind. .3 - Looking from the saloon towards to the open end, no car number apparent. .4 - Looking at the driver's bulkhead with the used ticket box and a hand on the controller. .5 - View of the driver's compartment - T1F Controller, PV brake valve and "Pay as you enter" reversed. .6 - Close up of the Westinghouse T1F controller. trams, tramways, interiors, controllers, brake valves, signs, westinghouse, tram 17, tram 28

This unique aircraft was conceived in 1943 as a two seat trainer. A very large part of the design work can be attributed to Jock Barratt and Harold Bradley. The general layout adopted is similar to the Kite I and Kite II single seat sailplanes of Martin Warner and Allan Campbell. Having regard to this heritage, the glider was originally named Kite III but renamed Pelican 2, perhaps because it was the second two seat training glider built by the Waikerie Gliding Club – the first being the Pelican, a reconfigured Pratt Utility glider. Pelican 2 was first flown in 1952 and regularly since then, at least until about 1992. The Pelican 2’s performance was found to be very good for sailplanes of its era and was often used for more advanced flying in addition to training new pilots. Very few changes have been made to the Pelican 2 over the years. The undercarriage was modified after its initial testing to improve the placement of the wheels. The trailing edge of the rudder (originally straight) was rounded adding to the surface area. The twin shoulder tow line bridles were replaced with a belly hook when aviation design rules declared shoulder bridles dangerous and a nose hook has since been added to allow for aero-towing. A unique home grown sailplane design associated with Australian gliding pioneers Wooden 2 seat glider sailplane with fabric covering. Distinctive features include the pod and boom fuselage with side by side seating for pilot and a second person. The canopy of perspex supported by aluminum framing opens with port and starboard segments separately folding upwards and forward. The instrument panel includes altimeter, airspeed indicator, slip indicator and variometers. In addition to the usual controls, there is a trim operated by a small wheel mounted centrally, at head height, on the bulkhead at the rear of the cockpit. Incorporated in the skid under the fuselage pod are two wheels (one approximately midships and the other at the rear end). It has a three piece cantilever wing of approximately nearly 17 metres. The ailerons run almost full length of the outer wing segments. A Gottingen 426 section has been used changing to M6 at the tips. Outer wing segments are joined to the centre section to give about 300 mm of dihedral at the tips. The glider is equipped with airbrakes. The colour scheme consists of orange fuselage with black nose and skid. The tailplane / elevator and rudder are painted white. The wing is predominantly white with an orange leading edge. Registration VH-GFY On each side of rudder – “Pelican II” in black lettering on a rectangle of silver On each side of fuselage pod the letters ‘FY’ On each side of the fuselage, below the edge of the cockpit opening – “WAIKERIE” in black paint. australian gliding, glider, sailplane, kite, pelican, waikerie gliding club, jock barratt, harold bradley, martin warner, allan campbell

This distress EPIRB unit (Emergency Position Indication Radio Beacon) was found on the beach at Levy's Point, Warrnambool, in December 2000 by a Warrnambool resident. Local police were alerted at the time. This distress signal unit is a world-wide COSPAS/SARSAT, satellite assisted, SAR (Search and Rescue) system for location of distress transmissions emitted by an EPIRB. Offshore cruising vessels must have such a unit as part of its essential safety equipment. This model EPIRB relies on four satellites with orbit times of approximately 100 minutes. Earlier units relied solely on aircraft flying overhead to detect and forward on the EPIRB’s location to Search And Rescue authorities, whereas this new system utilises satellites. An employee from the Lokata firm provided additional information about the Lokata EPIRB units. They had a machined aluminium case with labels that were also made on site. The units could be activated manually or automatically released when a magnetic switch in the case casing was activated. This later model, circa 1983, would have been mounted externally on a vessel's bulkhead in a spring-loaded, stainless-steel protective 'skeleton' mounting, The unit released when the water pressure sensor detected a set time it was under the water, in a similar way that life crafts were released. Each unit was registered to a particular vessel - the vessel's details on this unit are indecipherable. The Lokata Company was established in 1970, designing and manufacturing marine products including communications. The company no longer makes products with the “Lokata” brand. In 2001 Sartech Engineering Ltd. took over the support for the Lokata EPIRB beacons. This emergency location device is a late 20th century invention to help save lives at sea. It adds to the history of maritime life, its risks, the lives lost as sea, and the many inventions aimed as rescuing and saving lives. The local area is notorious for the number of lives lost through shipwreck. It also carries stories of heroic efforts to save lives, and other inventions to help reduce the chance of accidents at sea.EPIRB unit; “Emergency Position Indication Radio Beacon”. A distress communication unit for sending a distress location transmission in an emergency at sea. The EPIRB is a yellow, rectangular box with dials, buttons, indicator lights and instruction. An antenna protrudes from the top of the unit. The EPIRB unit sends a 406P (X) EPIRB, with 406M-Hz frequency, 48-hour duration signal. The maker was LOKATA Ltd in England. Remnants of a white label remain on the side. Circa 1980s."NAME OF VESSEL 'SERVICE IF SELF TEST FAILS' " “LO-KATA” moulded into the body. "406P (X) EPIRB" “Model 406” "Lokata Type No 92408" "UK Type approved to MPT 1278" "Class 2" "Made by Lokata Ltd, Falmouth Cornwall England TR10 8AE"" "LOKATE LTD. New North Road Hainault, Ilford Essex IG6 2UR" "ARMED / SAFE / TRANSMIT / CODE / DISPLAY / SET / wait / pass / fail / TEST" "IDENTIFIER / 1349:24034234N" [some characters may be different] "COUNTRY / DENMARK" "VESSEL IDENTITY / 124 [the rest is indecipherable]flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, emergency position indicating radio beacon, epirb, lokata ltd, marine safety equipment, satellite transmitting beacon, safety equipment, distress signal, life saving, safety at sea, shipwreck location, lo-kata, falmouth, emergency, beacon, radio signal, communication, marine equipment

Folder with papers - Manila Folder titled in ink "Motor Omnibus Acts" containing copies of the relevant Acts of Parliaments, memos and type extracts regarding the use of buses in Melbourne. Inside front cover - typed list of four Acts Bound with a brass clip: Act 3742 - "Motor Omnibus Acts" - 1928 with amendments Act 3851 - "An Act relating to Motor Omnibuses" Act 4032 - Amending of Section 35 of the 1928 Act] Act 4352 - "Provision with to the Control of Traffic on Roads" - 1935 - allowed State Govt to set regulations to control traffic in various Melbourne and Geelong Municipalities. Loose sheets "Extract from Victoria Gazette - 21/11/1945 - addition to the Metropolitan Motor Omnibus Regulations - re the interiors - seats and bulkheads. Various letters and memo to the Rolling stock Engineer, including a letter from Leyland's 1950 regarding Motor bus weights. Notes on "Motor Omnibus Acts" 3378 - Points to be observed, UK Metropolitan Stage (Motor) Carriages, Three page copy of a memo (last page loose) dated 26/11/1935 - Tenders for the supply of 10 additional motor buses - Leyland Cub buses - issues with the vehicles. See image i2.pdftrams, tramways, buses, leyland, acts of parliament, tenders, preston workshops

Set of four colour prints of an Ex Victorian Railways bogie tram body at Sloan NSW. Photo by Norm Cross, printed on AGFA paper. Photo dated 1/1/1994. Advised by Tony Smith - 29/3/2017 "The tram in question is VR 39. It was one of the last 4 trams disposed of from Elwood depot in 1959 after the system closed. They were purchased complete by Upton's machinery dealers of Corowa. The other cars were 29, 33 & 37. He then stripped them and sold the bodies. When we obtained VR 41 in 1977 we immediately went searching for other bodies that might yield parts to help in rebuilding 41. We located 37 on the outskirts of Wangaratta and it yielded many body items including a complete drivers bulkhead that was used to replace the one in VR 41 that had been cut out with an axle by the previous owner. You may also recall that we obtained 3 complete broad gauge 77e trucks from Upton's (they had cut up the other 5 bogies years previous). These 77E trucks are now under the Christchurch Brill tram with the 3rd as a spare as we were able to obtain standard gauge 77e's when we acquired L 105 for dismantling."Each photo has written in ink on the rear "Body of VR tram # @ Sloan NSW 1 Jan 1994, photo by Norm Cross".trams, tramways, vr trams, sale of trams, scrapped trams, tram 39

From the Victorian Heritage Register statement of significance H0791 The Marmalake/Murtoa Grain Store, originally the No.1 Murtoa Shed, is located within the Murtoa Grain Terminal, adjacent to the grain elevator tower and railway line. The shed is 280m long, 60m wide and 19m high at the ridge with a capacity of 3.4 million bushels. The hipped corrugated iron roof of the shed is supported on approximately 600 unmilled hardwood poles set in a concrete slab floor and braced with iron tie rods. These poles are the reason for use of the term "stick shed". With its vast gabled interior and the long rows of poles the space has been likened to the nave of a cathedral. An elevator at one end took wheat from railway trucks to ridge level where it was distributed by conveyor along the length of the shed, creating a huge single mound of grain. Braced internal timber bulkheads on either side took the lateral thrust of the wheat, and conveyors at ground level outside the bulkheads took wheat back to the elevator for transport elsewhere. Wheat had been handled in jute bags from the start of the Victorian wheat industry in the mid nineteenth century. Bulk storage had been developed in North America from the early 1900s. NSW began building substantial concrete silos from 1920-21. In Western Australia, farmers' co-operatives, who had to supply their own bulk storage from 1934-5, pioneered the use of low-cost horizontal sheds of timber and corrugated iron for bulk storage. Following its establishment in 1935 the Victorian Grain Elevators Board (GEB) planned a network of 160 concrete silos in country locations, connected by rail to the shipping terminal at Geelong. By the outbreak of the Second World War there was a worldwide glut of wheat, and Australia soon had a massive surplus which it was unable to export. Only 48 silos had been established under the Victorian Silo Scheme so far, and wartime material and labour restrictions prevented progress with this scheme. The storage deficit had become an emergency by 1941 as Britain obtained its imports from North America, rather than over the lengthy and difficult shipping route from Australia. In 1941 the GEB, under chairman and general manager Harold Glowrey, proposed large temporary versions of the horizontal bulk storage sheds already in use in Western Australia. The proposal was approved by the Victorian Wheat and Woolgrowers Association, who considered the use of shed storages as a longer term proposition. After initial resistance from the Australian Wheat Board, some of whose members represented wheat bagging interests, the Commonwealth and Victorian governments agreed to split the costs, and Murtoa was chosen as a suitable site for the first emergency storage. The main contractor, Green Bros, commenced work on the No.1 Murtoa Shed in September 1941, deliveries of bulk wheat began in January 1942, and the store was full by June of the same year. In the following years the Council for Scientific and Industrial Research (later CSIRO) conducted valuable research and experiment on the impacts and control of insect pests at the Murtoa No.1 shed. With these discoveries, and the development of more effective pesticides, use of the No.1 shed and the larger No.2 shed, erected in 1942/43, continued for many years. The No.2 shed was demolished in 1975. By the 1990s, pest resistance to pesticides and requirements for both pest free and insecticide free grain rendered open storage of this type unviable. The No. 1 store was also becoming increasingly expensive to maintain, and its use was phased out from 1989.Image of the Marmalake/Murtoa Grain Store which is of historical, architectural, scientific (technical) and social significance to the State of VictoriaDigital colour image of the interior of the Marmaduke . Murtoa grain storage facility better known as the Stick Shed. The shed was constructed in World War Two to store grain. The supporting columns are trees.marmalake, murtoa grain store, wheat store, stick shed, murtoa

Steel screw steamer launched 1889 at Newcastle on Tyne by Palmers & Co., built for Archibald Currie and Partners - the Currie Line of Melbourne. Gross tonnage: 2,792, Length: 99.06m (325'). Width: 12.3m (40.3'). Triple expansion steam engines producing 363 nhp. Avge speed 11 knots. Coal consumption 26 ½ tons per 24 hours. Steel hull, one funnel, two masts, barque rig. • 1889: Argus launched. Worked in the Australia to India trade, passengers, goods and horses. • 1891 July: While taking coal from Newcastle to Singapore, ran onto sunken rock in Gaspar Strait (in Indonesia). Watertight bulkheads held, got to Singapore, was repaired for two months, 60,000 Straits dollars (about £12,000). • 1895 July: While taking 400 horses to Colombo, ran onto reef near Somerset, North Queensland. holed, water in two compartments. 400 tons coal jettisoned, finally got off in spring tides. • 1901 Feb: During Boer War took Victorian contingent, 5th Mounted Rifles, fromMelbourne to Durban and Cape Town, with 500 horses. • 1901 Dec: Took horses for Boer War from Brisbane to Durban. • 1903 31 July: Leaving Sydney for Calcutta with 86 horses, 20 passengers including the Sultan of Johore, was rammed by the incoming steamer Mildura (on the wrong side of the channel). Argus's side plating was cut from deck to below waterline, had to be beached on Goat Island to prevent sinking. Refloated 2 August and repaired. • 1905: Argus sold to the Japanese shipping company, Osaka Shosen Kaisha. Renamed Giran Maru. • 1907 11 Sept: Wrecked in Soya Strait, between Hokkaido & Sakhalin Island.Built for Archibald Currie & Partners, Melbourne. Carried passengers between Australia and India and between western and eastern Australia.Large ship builder's model in glass case

Model ship was presented to the Melbourne Maritime Museum by the British Phosphate Commissioners. Built as Tri-Ellis (1958-74), Tryphena (1974-78), Man Tat (1978-80), 1980 broken up. DWT 13,756 SPEED 14 KNOTS.AT 112RPM. BOILERS LARKSON TRIMBLETUBE. FUEL CONSUMPTION 7 TPD. GENERATORS W.H.ALLEN - 4CYL.2SA290/470. 480B.H.P.320L.W.-220V 333RPM DAILY CONS - 1.5 TONS. EMERGENCY GEN R & H. 40 K.N. -220V. REFRIGERATING MACH: J & G HALL LTD. SUPERSTRUCTURE: FORECASTLE 62'..2 DECKS RIVETED AND WELDED. CARGO BATTONS NOT FITTED. 9 BULKHEADS. RISE OF FLOOR 6".WATER BALLAST 3,296 TONS INCLUDING TUNNEL TANKS 1,341 TONS. 'TWEEN- DECKS FORWARD 274 TONS. REFRIGERATED CARGO INSTALLATION - 6 HOLDS - 55.2',52',54',59.5',43' ,53'. GRAIN CAPACITY :621,640 CU. FT. BALE CAPACITY : 573,810 CU. FT. INSULATED CAPACITY : 5,050 CU.FT. 6 STEEL HATCHWAYS (27',30',30'* 30') (30'* 27.75') (27', 24' * 28' ). 12 WINCHES...DERRICKS 1 (25), 2 (10), 10 (5). MACHINERY: OIL 2SA 7CY.C20 * 1400MM EXHAUST 470MM. 6500 BHP. FUEL BUNKERS: 2135 TONS HIGH VISCOCITY FUEL. The main engine was an opposed piston type Harland & Wolff 6-620/ 1870 6 for the number of cylinders.. 620 for the cylinder bore and 1870 for the combined strokes of the main exhaust pistons in each cylinder. This engine was based no a Burmeister and Wain design but H & W gave these engines their own type designation. Sailed on board its maiden voyage to Australia via Casablanca Morocco where she collected her first load of phosphate. We sailed to Geelong via the Suez canal and the Port of Aden (Yemen) and Freemantle. The first load of phosphate was unloaded at Corio Bay (geelong) Formerly part of the collection of Melbourne shipping company, Howard Smith Ltd. Ship builder's model of the cargo ship Tri-Ellis IMO 5368196 - Body of moulded polyurethane painted in red, black and grey, the deck painted in red, with detailed fittings, machinery, rigging and superstructure, raised on a wooden base. Original ship built Clyde 1958, 11,761 gross tonnes, 531.5' x 68' x 31' (162.0 x 20.73 x 9.45m)plaque at foot of model "MV TRI ELLIS/ LENGTH B.P. 486'-3"- BREADTH MLD 68'0" - DEPTH MLD 40'6"/ TONNAGE GROSS 11,760/ Built by HARLAND & WOLFF LTD/ For BRITISH PHOSPHATE COMMISSIONERS" On model "TRI-ELLIS" painted black

On of a class of 120 trams built at Preston Workshops between 1939 and 1951. Third tram to be converted to a Colonial Tramcar Restaurant Tram. Of the six trams converted, the only former Melbourne Restaurant tram in use currently (March 2019), trams 4, 5, and 6 having been withdrawn during October 2018.Four motor bogie tram - ex Melbourne - tram No. 939 - One of a class of 120 trams built at Preston Workshops between 1939 and 1951. Third tram to be converted to a Colonial Tramcar Restaurant Tram. Of the six trams converted, the only former Melbourne Restaurant tram in use currently (March 2019), trams 4, 5, and 6 having been withdrawn during October 2018. The tram was built by the MMTB as No. 939 in 1948 at Preston Workshops as a standard SW6 tramcar. It was resident for most of its life at Camberwell, Kew and South Melbourne depots and finally Southbank depot. Heavily rebuilt internally to give a flat floor, air-conditioned, 240V and 24V systems fitted along with changes to bulkheads and position of the passenger door and a goods door in 1994. The tram was converted into Melbourne Restaurant tram No. 3 in 1994/95, being launched on 8-2-1995. While in the later part of its use by the Colonial Tramcar Restaurant Co, it was named “Valentine” during July 2008. It was withdrawn from service in May 2012, when it was replaced by No. 935 (Restaurant No. 6). In August 2014, the Museum received a grant from the Victorian Government of $40,000 to refurbish tram – part of the Transport Investing in Regions Program. The tram was relocated to the Ballarat depot on 29/10/2014. Refurbishment work was completed during March 2016 and the tram was formally launched on 5/4/2016.. The tram is named after Sir Henry Cuthberts (1829 - 1907), the first Chairman of the Ballaarat Tramway Co (the horse tram operator). Sir Henry was a Ballarat based solicitor, member of the Legislative Council, Knighted in 1897 and strong supporter of many Ballarat institutions. Photo Warren Doubleday 5-4-2016.trams, cuthberts 939, restaurant tram, sw6 class, tram 939

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 125 NQR - Open Medium Truck 20/ 5/1910 NWS Built new VR Service History *NQR 125.VA - 20/ 5/1910 NWS Built new - / /1926 - To NQ 125.VA - Puffing Billy Service History or Notes Untrafficable at Emerald Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck125 NQR - Open Medium Truck made of Steel and metal125 NQRpuffing billy railway, pbr, rolling stock , 125 nqr - open medium truck, nqr open medium truck, victorian railways