Fob (or pocket) watches were developed in Europe in the 16th century and gained wide usage during the mid 18th century until World War 1 when the wristwatch was invented. These watches were designed to be carried in a small pocket and attached through the means of a 'fob' which could be a chain or made from a variety of materials such as leather. Their popularity peaked in the nineteenth century where they were an important part of middle and lower class society as well. The inclusion of the word RAILWAY on the face of the watch suggests a possible use by an employee of the railways. This item is of social significance as fob / pocket watches were valued as an essential object in all levels of society. For some occupations, such as the railroads, it was a necessary tool of the job. Steel Railway Lever open face pocket / fob watch dated 1920s-1930s. The white dial has large black arabic numerals and outer minute divisions around the edge. A circular insert and small hand to show the seconds is at the bottom of the watch face. The hour hand is a rounded leaf shape, and the minute hand a thin diamond shape. Both hands and the small rounded end of the second hand reflect a metallic blue sheen in the right lighting. The words RAILWAY LEVER, 15 JL and SWISS MADE are on the dial. The lever set on watches was a requirement for railroad watches. It required a two step process for the hands to be adjusted. 15 JL refers to the movement being a 15 jewel one.The front dial of the watch has the words 15 JL, RAILWAY LEVER, and SWISS MADE. flagstaff hill maritime museum and village, warrnambool, great ocean road, shipwreck coast, fob watch, pocket watch, watch, horology, time keeper, swiss made, railway lever, 15 jl, 15 jewel

Set of two photos of Y1 class tram No. 610 on a tour on the Royal Park line August 1971. The second photo shows the tram reversing at the Royal Park crossover with the railway station in the background. Note the open ballast style track and railway style weighted point lever.Yields information about the Royal Park tram line.Set of two Kodachrome cardboard mounted slides.tramways, tramcars, y1 class, tram 610, royal park, railways

Hardcover. Green dust cover. Front cover photograph is Krauss 0-4-OWT, builder's No. 2459 of 1891, takes water at the western end of Rubicon Lane in 1934. Driver Bob Rees attends to his engine while brakeman Hayden looks on. End papers show a photograph of a man standing besides a timber railway trolley holding onto the brake lever. There is a group of men, some sitting and some standing, on piles of cut timber under a large, open shed in the background. There are also some small, timber, tent like structures standing next to the railway tracks. There is a forest in the far background. Written in white is the line "Mr Clarke & Kidd's Sawmill". non-fictionrubicon, timber, sawmill, railway, tramway, clarke and pearce, evans, peter, marysville, krause, forest, mountain

A history of the Rubicon forestHardcover. Green dust cover. Front cover photograph is Krauss 0-4-OWT, builder's No. 2459 of 1891, takes water at the western end of Rubicon Lane in 1934. Driver Bob Rees attends to his engine while brakeman Hayden looks on. End papers show a photograph of a man standing besides a timber railway trolley holding onto the brake lever. There is a group of men, some sitting and some standing, on piles of cut timber under a large, open shed in the background. There are also some small, timber, tent like structures standing next to the railway tracks. There is a forest in the far background. Written in white is the line "Mr Clarke & Kidd's Sawmill".Stamp of the Marysville & District Historical Society Inc / PO Box 22 / Marysville 3779 Signed by the author, Peter Evansrubicon, timber, sawmill, railway, tramway, clarke and pearce, evans, peter

Typed carbon copies of two letters stapled together. The first letter is from W. H. Noe to R. H. A. Abbott and dated 25 July, 1938 discussing Scalebuoys and who was using them. The second letter is from W. H. McCorkingdale to Mr. Hough, Works Manager, Lever Bros. (N.Z.) Ltd., dated 25 July, 1938. Letter mentions the use of Scalebuoys, application, companies using them, and he asks if considering Scalebuoys at the works to send him some information.sciences, instruments - general, scalebuoy, bill ashman collection - correspondence, scalebuoys new zealand limited, r h a abbott, scott's hotel melbourne, hardley's works, lever bros of australia, mr hough, w h noe, hawke's bay farmers' freezing company, mater misericordiae hospital auckland, st joseph's, whangarei dairy company, maungatapere dairy company, n z railways, the union oil soap & candle company, knox's home, moody's dye works, ellis & burnand (sawmillers), walter buchanan ltd, findlay's gold krust bakeries, kaiticke dairy company, pennsylvania rubber company, page-hersey tube company, w h mccorkingdale

8405.1 - Forked, curved chisel; one end is well-hammered into a smoothly-curving surface. Use on mine rails, likely to lift rails by means of lever-action around railway spikes.

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

Zeehan & North East Dundas Tramway Bogie 1896 The North East Dundas Tramway (NEDT) was a 2 ft (610 mm) narrow gauge tramway on West Coast Tasmania that ran between Zeehan and Deep Lead (now Williamsford). It was part of Tasmanian Government Railways. The line was opened in 1896 to carry ore from the Williamsford mines to Zeehan where it would be loaded onto another train for shipment to Burnie. The narrow-gauge (2 ft) was chosen because of the extremely difficult terrain that the railway crossed, requiring several big trestle bridges, including one at the foot of Montezuma Falls. After some rain the engine and carriages would get soaked by spray from the falls. There was a break-of-gauge with the mainline 1,067 mm (3 ft 6 in) system at Zeehan. The railway was closed in 1932. The rolling stock for the Tramway was built in the Launceston Railway workshops, and comprised twenty five eight-wheel low-side trucks, tare 3 tons 1 cwt. 1 qr., load 10 tons; six eight-wheel flat trucks, tare 2 tons 18 cwt. 1 qr., load 10 tons; two four-wheel bolster trucks, for carrying long timber, tare 1 ton 19 cwt., load 5 tons; and four passenger cars, each with six cross-seats with reversible backs, to carry eighteen passengers, also a locker for mails and parcels. All trucks and cars have cast-steel wheels 21 inches in diameter and are fitted with automatic vacuum brakes. The trucks have side levers and the cars have hand-screw brakes. The vacuum brake can be worked from the engine or from the passenger cars, which act as brake vans. When this brake was introduced, one effect was to accelerate the journey speed by about 10 minutes owing to more even running on down gradients. Historic - Industrial Narrow Gauge railway - Bogie used on the Zeehan & North East Dundas Tramway, Tasmania, Australia Bogie made from steel, iron and wrought ironZN & NTDS ML TRAM 1896 Griffinpuffing billy, bogie, zeehan & north east dundas tramway bogie, zeehan & north east dundas tramway, industrial narrow gauge railway, gauge: 2' (610 mm)

Railway Track Tool Rail is heavy, sometimes as much as 120lbs per yard. To assist in being able to move rail, a special bar was developed. Using the handle as a lever, one section clamps onto the rail, allowing it to be moved. Historic - Railway Permanent Way and Works - track equipment - Railway Track ToolRailway Track Tool made of forged ironpuffing billy, railway track tool

1920's Station Cash Box Tin Made by Hobbs & Co London Lever Machine Made Alfred Charles Hobbs (October 7, 1812 – November 6, 1891) was an American locksmith and inventor. Hobbs went to London as a representative of the New York company of Day & Newell, which was exhibiting at the Great Exhibition of 1851. Hobbs had brought with him his boss's (Robert Newell) Parautoptic lock, designed to compete with, and surpass, the locks available at the time in Britain. He was the first one to pick Bramah's lock and the Chubb detector lock at the Great Exhibition of 1851 and forced the lock manufacturers to improve their designs. The lock controversy continues a subject of great interest at the Crystal Palace, and, indeed, is now become of general importance. We believed before the Exhibition opened that we had the best locks in the world, and among us Bramah and Chubb were reckoned quite as impregnable as Gibraltar— more so, indeed, for the key to the Mediterranean was taken by us, but none among us could penetrate into the locks and shoot the bolts of these masters. The mechanical spirit, however, is never at rest, and if it is lulled into a false state of listlessness in one branch of industry, and in one part of the world, elsewhere it springs up suddenly to admonish and reproach us with our supineness. Our descendents on the other side of the water are every now and then administering to the mother country a wholesome filial lesson upon this very text, and recently they have been "rubbing us up" with a severity which perhaps we merited for sneering at their shortcomings in the Exhibition. In 1854 he was awarded a Telford Medal by the Institution of Civil Engineers for his paper 'On the Principles and Construction of Locks'. Sign on a strong room door. Hobbs became one of the founders of the lock making firm of Hobbs Hart & Co. Ltd. The company started in 1851 and was formally registered as Hobbs and Co. in 1852. But by 1855 it had become Hobbs, Ashley and Company. The name then changed to Hobbs, Ashley and Fortescue, with an address at 97 Cheapside in London. Then for the next ninety years the address was 76 Cheapside in London. In 1860 Hobbs returned to America and lived in Bridgeport, Connecticut, and went on to hold a dozen patents for firearm ammunition manufacturing. In 1880 he listed himself as a "Superintendent Of Cartridge Factory" Info from https://en.wikipedia.org/wiki/Alfred_Charles_HobbsHistoric - Railways - Station Cash Box Tin 1920's Station Cash Box Tin - Hobbs & Co London Metal Tin - painted Black, Gold and Red with Brass Lock and HandleHobbs & Co London Lever Machine Made1920's station cash box tin, puffing billy

By1880 most railway crossings were identified by a sign, although at very busy crossings a watchman was posted. Eventually most stations were manned and gates were installed. The watchman was generally housed in a small wooden or brick building with a clear view of the single line. The next stage was mechanical closing of the gates, using a lever situated in a shed behind the gatehouse. By 1956 automatic barriers had been installed. A working model of the gate style crossing can be seen at New Street Brighton.A collection of 12 black and white photographs of the Windsor family who lived in the gatehouse next to the Tunstall station. The stationmaster Ernest Windsor was also responsible for track maintenance between Ringwood and Middleborough Road Box Hill. His wife Betty Jean Windsor was gatekeeper for 2 years. On the back of each photograph are the names of the family members in the photo.Catherine Ann Windsor (born 1897), John Ernest (Ern) WIndsor, Catherine (Kitty) Windsor (born 1919), Patricia Janette WIndsor (born 1935) Tunstall Railway Gatesstationmasters, tunstall station, windsor ernest, windsor catherine, windsor patricia, windsor betty, windsor catherine (kitty)

Cudgewa Line -The Cudgewa railway line opened in stages between 1889 and 1921. The first section from Wodonga to Huon opened on 10 September 1889. It was extended to Bolga on 18 July 1890, Tallangatta on 24 July 1891, Shelley on 13 June 1916 (the highest station in Victoria), Beetomba on 10 April 1919 and Cudgewa on 5 May 1921. The line had 1 in 30 grades and trestle bridges that have been heritage listed. In 1919, the line was used to carry materials for the construction of Hume Weir, and three years later a spur line connecting Ebden to the weir was opened. In the 1960s, Cudgewa became the railhead of materials for the Snowy Mountains Scheme. The last passenger service from Wodonga to Tallangatta ran on 30 September 1961. The turntable and passenger platform at Cudgewa were abolished in 1976. This fish plate came from the rails of the Cudgewa Line at Gordon Roy's hut which was situated behind Perry's Stump Hotel outside Wodonga. The hut was used as an office with the points lever outside to switch trucks to different tracks on the Bandiana and Cudgewa lines.This item is significant as it was part of the railway line to Cudgewa which played an important role in North east Victoria carrying freight during the construction of the Hume Weir and the Snowy Mountains Scheme.A section of flat plate. These plates were used in pairs to connect the ends of adjacent rails in railway track. victorian railways, cudgewa rail line, railway components

A beige coloured book with green binding. The cover includes the Royal Coat of Arms, a summary of the purpose and contents of the manual, and the date the instructions become effective, all printed in green ink. This information is enclosed by a green border. non-fictionThis manual was issued by Victorian Railways in 1967 to explain all of the railway signals used throughout Victoria. It included a detailed outline of the signals used at every railway station, including small depots and sidings throughout Victoria. Illustrations of the different signal systems are included in the text. Every driver, fireman, guard, shunter, and every other employee designated by the Head of the Branch concerned, had to be supplied by his superior officer with a copy of this book. They were required to become thoroughly acquainted with the particulars which related to their duties. The included informations was effective from 3rd August, 1967 until further notice.victorian railways, victorian railways -- rules and practice., railway signals

Black and white photograph of W5 No. 779 inbound to the City and Domain Road on route 56, on the open ballasted track just before passing under the railway line at the Zoo gardens area. Shows the open doors with the bars down. Photo of the tram slightly out of focus. Taken early 1950's by an unknown photographer. In the overhead shows a sign black cross in a circular disc and behind the tram a incandescent light suspended in the middle of the overhead. The photo shows the construction of the track at this location, dog spiked sleepers, the rail supports for the inner check rail. In the background behind the tram is the lever for the points of the crossover.On the rear in red ink "Melbourne tram shows use of Off-street tracks in an outer suburb"trams, tramways, zoo tram, reserved track, track construction, w5 class