Showing 150 items matching tools-and-equipment
Container (1218) Equipment (1887) Functional object (4020) Instrument (409) Machine (358) Tool (1467) Vehicle (150) Weapon (458)-
Queenscliffe Maritime Museum
Vehicle - Dinghy, clinker planked
Clinker timber dinghy, varnished topside -
Queenscliffe Maritime Museum
Vehicle - Workboat ex Wyuna
In 1974, this 18 foot (5.5 meter) diesel-powered workboat was one of the last boats built to operate from the pilot cutter Wyuna. These boats were used to transfer pilots from the Wyuna to the ship being serviced or vice versa. Until 1946 they were propelled by two oars then simplex two-stroke petrol engines were fitted followed by diesel engines. The Pilot Service Shipwrights built the boats in a shed which stood on the site of the present Pilot Station, Tobin Drive, North of Shortland Bluff. The design is based on a Gig and was developed by the Pilots as suitable for the severe conditions at the entrance to Port Phillip. To understand how these boats were used view the film "Through The Rip" on the video in the Exhibition Hall.Close association with QueenscliffTimber Workboat used to transfer pilots between Wyuna and ship requiring servicepilot service, wyuna, workboat, boat buiding, port phillip sea piots -
Trafalgar Holden Museum
Vehicle - EH Holden special sedan, August 1963 - February 1965
It was the first Holden to incorporate the new "Red" engine, with a 7 main bearing crankshaft instead of the 4 main bearing crankshaft used in the "Grey" engine. The larger capacity 149 ci (2400cc) engine was first only sold attached to a three-speed manual gear box or the "Hydramatic" three-speed automatic transmission with a (column shift). Although the Controlled Coupling Hydramatic used in the EH was actually a four speed, it effectively worked as a three speed unit except at full throttle. The 179 ci (2900cc) engine was initially only sold with the "Hydramatic" three-speed. The first EH with a 179 ci engine and a manual gear box was called the "EH-S4", fitted with an up-graded manual gear box, with stronger gears than the 149ci gear box and an up-graded clutch. The three-speed manual (column shift) gear boxes had no synchromesh on first only second and third 'top gear'It was the first Holden to incorporate the new "Red" engine, with a 7 main bearing crankshaft instead of the 4 main bearing crankshaft used in the "Grey" engine. The larger capacity 149 ci (2400cc) engine was first only sold attached to a three-speed manual gear box or the "Hydramatic" three-speed automatic transmission with a (column shift). Although the Controlled Coupling Hydramatic used in the EH was actually a four speed, it effectively worked as a three speed unit except at full throttle. The 179 ci (2900cc) engine was initially only sold with the "Hydramatic" three-speed. The first EH with a 179 ci engine and a manual gear box was called the "EH-S4", fitted with an up-graded manual gear box, with stronger gears than the 149ci gear box and an up-graded clutch. The three-speed manual (column shift) gear boxes had no synchromesh on first only second and third 'top gear'Two tone, blue body and white roofon the boot of this car there is a 179 badge stating that this car was powered by the larger motor available. There was also a "Hydra-matic" badge showing this vehicle was fitted with an automatic transmission. Registered number 63454-Hholden, 1963 - 1965, car -
Flagstaff Hill Maritime Museum and Village
Vehicle - Furphy Water Cart, J. Furphy & Sons, c. 1942
This horse-drawn, two-wheeled cart with a tank, is known as a Furphy Farm Water Cart that was made in Shepparton, northern Victoria, c. 1942. John Furphy (1842-1920) was born in Moonee Ponds, in 1842 to Irish immigrant parents and subsequently raised in the Yarra Valley before the family moved to Kyneton in central Victoria, where he completed an apprenticeship with the firm Hutcheson and Walker. Murphy began operations of his own at a site on Piper Street in Kyneton in 1864. He relocated for a business opportunity and founded the first blacksmiths and wheelwrights shop in the newly surveyed town of Shepparton in 1873. Furphy invented many farming tools and machines including a patented grain-stripper, and won awards at the 1888-89 Melbourne International Exhibition. His most famous invention is the Furphy Farm Water Cart, designed in the 1880s, at a time when water for most households and farms was carted on wagons in wooden barrels. The Furphy’s water cart is a single item that combines a water metal tank and a cart. The design of the cart was simple yet effective, and became popular very quickly and established itself as a vital piece of farming equipment. The water cart has had a number of words cast into its ends over many years. References to the foundry’s location in Shepparton, as well as advertising of other products also manufactured by J. Furphy & Sons were present on the ends. However, the most significant set of words to feature on the tank, was a poem encouraging continual improvement: ‘Good Better Best, Never Let it Rest, Until your Good is Better, And your Better Best’. During The Great War (1914-1918), the water cart was used by the Australian militarily at a large AIF (Australian Imperial Force) camp in Broadmeadows (Melbourne) where thousands of men were camped for months, before being transported aboard. Furphy Water Carts provided water to the troops, and were usually placed near the camp latrines, which was one of the few places the troops could share gossip and tall tales away from the prying eyes and ears of their officers. The water cart drivers were also notorious sources of information, despite most of their news being hearsay, or totally unreliable. By the time the men of the AIF were in engaged in combat on the Gallipoli Peninsula and the Western Front, the carts used for water supply had no markings and became simply referred to as Furphys. This owed as much to the coining of the term ‘Furphy’, Australian slang for suspect information or rumour. After a number of decades as principally a soldier’s word, 'Furphy' entered the broader Australian vernacular and was used mainly by the political class until recently when the term was taken up by a Australian brewer as a beer brand. This Furphy Water Cart was purchased by Friends of Flagstaff Hill in 2014. The support of local individuals, organisations and businesses enabled its restoration and later its installation alongside the existing late-19th century water pipe stand and 1940s hand pump The Furphy Farm Water Cart is of historical significance as it represents a famous Australian time-saving and energy-saving invention of the 1880s, replacing the labour intensive activity of collecting and dispensing water from barrels and casks on the back of carts. The water cart’s connection with manufacturing companies J. Furphy & Sons and Furphy Foundry are significant for being early Australian businesses that are still in operation today. Furphy carts are of military significance for the role they played during The Great War (1914-1918) in Australian army camps, and theatres of war in Europe and the Middle East, to supply the AIF troops with fresh water. A wooden framed, two-wheeled, horse-drawn cart, fitted with a horizontally mounted, cylindrical metal tank. The tank is made of rolled, sheet steel with a riveted seam, and cast iron ends with cast iron ends. The spoked metal wheels have fitted flat iron tyres and metal hubs. A metal pipe is joined to the outlet. The tank is silver coloured, the ends, wheels and trims are crimson, and the script lettering on tank sides is black. There are inscriptions on the tank, ends, and hubs. The water tank was made in 1942 in Shepparton, Australia, by J. Furphy & Sons and has a capacity of 180 gallons (848 litres). Hub perimeter, embossed “J. FURPHY & SONS” “KEEP THE / BOLTS TIGHT” Hub centre embossed [indecipherable] Tank, each side, painted “J. FURPHY & SONS / Makers / SHEPPARTON” Tank ends, embossed – “FURPHY’S FARM WATER CART” “BORN ABOUT 1880 – STILL ‘GOING STRONG’ 1942” “j. FURPHY & SONS / MAKERS / SHEPPARTON - VIC “ “S - - - - - L MANUFACTURERS” [SPECIAL] “SPIKE ROLLERS” “SINGLE TREES” “PLOUGH WHEELS” “IRON CASTINGS” “LAND GRADERS” “STEEL DELVERS” “CAST IRON PIG” “CHAIN YOKES” “GOOD – BETTER – BEST / NEVER LET IT REST / TILL YOUR GOOD IS BETTER / AND YOUR BETTER – BEST” Image [Stork carrying a baby] above shorthand, transcribed "Produce and populate or perish" Image [Furphy Pig Feeder] beside ‘Cast Iron Pig’ Shorthand, transcribed “"Water is the gift of God but beer and whiskey are concoctions of the Devil, come and have a drink of water"warrnambool, flagstaff hill maritime museum, water cart, furphy cart, furphy tank, furphy farm water cart, furphy, john furphy, john furphy & sons, furphy foundry, kyneton, shepparton, mobile water tank, jinker, hutchinson & walker, blacksmith, farm equipment, implement maker, tool maker, horse drawn, stork and baby, good, better, best, barrel, tank, first world war, wwi, eastern front, gallipoli, j furphy & sons -
Trafalgar Holden Museum
Vehicle - Vauxhall Cresta, 1959
This model was an early venture by General Motors in a more streamlined body shape than previous vehicles.This 1959 Vauxhall was bodied by GMH at the Dandenong plant in 1959. This vehicle went on sale in competition to the new FB Holden and was originally considered a serious challenge to the Holden.White body, blue roof, Four door sedan with mirror on driver’s door.Vauxhall badge middle of bonnet.. Cresta badge rear quarter panel. Chrome strip with Vauxhall on boot. vehicle, vauxhall crest holden, car -
Trafalgar Holden Museum
Vehicle - T Model Ford
A large number of T model's started their life in Australia being bodied by Holden Motor Body Builders between 1915 and 1927.The mode accounted for 57% of the worlds automotive production Ford took over production in Geelong in 1925White body with red mudguards open coupet model ford, vehicle, cars, holden -
Trafalgar Holden Museum
Vehicle - Lloyd Hartnett
Car was based on a Lloyd motor corporation vehicle, first manufactured in Frankston, Victoria, between 1949 and 1953Built on request of the then Prime minister, Ben Chifley, that Holden build an inexpensive "workingman's car". The Lloyd was Laurence Hartnetts idea of this, and commenced to develop the car The car is powered by a 2 cylinder, 4 stroke horizontally opposed engine of 600 cc capacity.Green 2 door Estate Wagon with vinyl roof and timber window surroundsInsignia badge on bonnet centre, Lloyd Hartnett across grille top vehicle, estate, hartnett, car -
Whitehorse Historical Society Inc.
Vehicle - Spring Cart, C1930
This item was used as a general purpose cart on the Livermore Orchard in Vermont and was donated by Mr. Livermore when the orchard was sold for housing development.|In the 1840's a vehicle known as a springcart, chaise cart, and family cart was the choice of colonist who needed to travel from town to town. It was light, well sprung, capacious and adaptable. It was used by all stratas of society. See ref.Two wheeled general purpose spring cart, used on an orchard. Also known as a 'Jingle'. It is painted green and terracotta. It was pulled by one horse and has internal measurements of 0.46M x 1.5M x 2.46M.The wheels are 1.1M in diameter.rural industry, livestock, transport, horse -
Port Fairy Historical Society Museum and Archives
Vehicle - Artefact, 1930s
Retrieved from crashed (during W.W.2) Avro Anson aircraft at Propeller Bay near Lady Julia Percy Island in 13 metres of water. Found adjacent to the remains of the engine and propeller in June 1993 by Peter Ronald. It was possibly used to adjust control cables. The plane went down on the 15th February 1944 Flight Sgt. J.H. MacLellen, Flight Sgt D.l. Baulderstone, LAC N.T. Kruck, LAC B.C. Ladyman were killed. A memorial was erected at the 'Crags' on the 14th of February 2015 . " At 0800 Anson AW878 of 2AOS took off from Mount Gambier to carry out a radius of action navigation exercise to Lady Julia Percy Island (located off the Victorian coast, midway between Portland and Warrnambool) and back to Mount Gambier. By 1230 it was overdue, and that afternoon a search was instituted. No radio messages had been received from the Anson, although it had been seen during the exercise by another aircaraft. At 1430 part of the mainplane was sighted on Lady Julia Percy Island. Subsequently a fishing boat searched in the vicinity of the island and passed through small pieces of wreckage strewn over about 3 miles. A further search uncovered wreckage which identified the plane beyond doubt, including fuel tank bay cover with AW878 penciled on it, and a Mae West which had been signed out by one of the crew. The bodies of the four crew were never located." This information comes from a report at Mt Gambier Airport where the plane was stationed.Two small pieces of metal that bring the reality of war to our shoresArtefact from crashed aircraft at Lady Julia Percy islandlocal history, transport, aviation, aircraft, lady julia percy island, j.h. maclellen, d.l. baulderstone, n.t. kruck, b.c. ladyman -
Trafalgar Holden Museum
Vehicle - V U Utility Sandman SS, 2000 until 2002
The Holden V U ute was decorated with a paint job to represent " Bushfire" with the combination of the colours and how they are applied.This vehicle was a promotional car built and decorated to be shown at motor shows.V U Model utility vehicle with gold and burgundy swirls, the name Sandman written in brown across the tailgateSANDMAN across the the tailgate Holden badge bonnet centre HOLDEN across windscreenvehicle, promotional, v u sandman -
Queenscliffe Maritime Museum
Vehicle - Punt
Made at Port of Melbourne Authority [P.O.M.A] shipwrights shop Williamstown in 1975P.O.M.C. wharf carpenters maintenance puntworking boats, poma, williamstown, shipwrights -
Central Highlands Tourist Railway (Daylesford Spa Country Railway)
Vehicle - Double Ended Leyland Rail Motor, Victorian Railways, 53RM, 1926
Double Ended Leyland Rail Motorvictorian railways, rail motor -
Flagstaff Hill Maritime Museum and Village
Vehicle - Vessel - Dinghy, Proudfoot's Boat, c. 1885
This boat or dinghy is one of a few remaining boats made for Proudfoot’s Boathouse, 2 Simpson Street Warrnambool, on the Hopkins River, in about 1885. It was one of many rowing, fishing, sailing and picnic boats that were available to hire. Proudfoot’s Boathouse, a beautiful Victorian Period building, was designed, built and established by Thomas Proudfoot. He applied to build a boat jetty in 1885. He died in 1900 and his wife Catherine took over, running it for many years. Later her son Bruce and after that her granddaughter Ena Hunt and her husband took over; it remained in the family until 1979. Proudfoot’s was a very popular tourist destination for visitors coming from Melbourne to fish and row and enjoy afternoon tea. The buildings, including the ‘U’ shaped jetty and tearooms, were restored and modified in the 1990s by the Warrnambool Sports Club, under the control of the Warrnambool City Council. The dinghy was brought to Flagstaff Hill in about 1992 and restored to its original condition and painted in traditional paint colours of orange with dark green gunnel and black and gold pinstripes. Since that time it has been painted by Flagstaff Hill's boatbuilder.This dinghy, Proudfoot’s Boat, is significant for its association with Proudfoot’s Boathouse, which is listed on the Victorian Heritage Register, VHR H0620. “Proudfoot's Boathouse on the Hopkins River near Warrnambool is an outstanding example of a late-19th century boathouse complex with associated residences and jetties. Thomas Proudfoot first applied for a jetty licence in 1885 with a view to establishing a boating business on the Hopkins River. The early single-storey sections are thought to date from this period. The two storey second stage probably dates from 1893 when additions were constructed. The entire complex was designed and built by Proudfoot himself. The business remained in the Proudfoot family until 1979. The buildings were modified in the 1990s in the process of creating a sporting club on the site. Proudfoot's Boathouse is of architectural, historical and social significance to the State of Victoria. Proudfoot's Boathouse is of architectural significance as perhaps the finest example of a 19th-century boathouse in Victoria. Although recent modifications have reduced the intactness of the buildings, many original features remain. The beautifully ornamented buildings still provide an attractive instance of 19th-century leisure facility architecture. Proudfoot's Boathouse is of historical significance as an example of late-Victorian recreational and tourist facilities. Boathouses were popular 19th-century tourist and recreational attractions, providing refined and healthy activity. This boathouse shows the early realisation of the tourism and leisure potential of seaside towns such as Warrnambool, a potential that has become increasingly important as port uses have ceased and other industries have been subjected to financial pressure. Proudfoot's Boathouse is of social significance because it illustrates the continuity of the attraction of this kind of leisure facility. Although the glory days of the boathouse were in the 19th century, those that survive continue to be well patronised. Proudfoot's Boathouse has been an important recreational facility and attraction for tourists flocking to the Hopkins River, one of the State's most popular boating and fishing resorts, since 1885.” (Statement of Significance is from the Victorian Heritage Register)Wooden vessel or boat, called a dinghy, known as Proudfoot’s Boat. Paint work is orange with dark green gunnel and black stripe. The rowboat is propelled by oars and has two pair of thole set into the gunnel (gunwale) to hold the oars in place and to serve as a fulcrum when rowing. The boat is dated around 1885. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, small marine vessel, dinghy, proudfoot's boat, proudfoot's boathouse, picnic boat, orange and black boat -
Central Highlands Tourist Railway (Daylesford Spa Country Railway)
Vehicle - Passenger Mail Motor, T.J. Richards, RM74, 1936
Dodge Passenger Mail Motor RM74Victorian Railway 1936 livery of Black and Chrome Yellow stripesvictorian railways, dodge, mail motor -
Trafalgar Holden Museum
Vehicle - Buick Sedan, 1938
The Special Sport Sedan is a rear wheel drive saloon (sedan) motor car with a front located engine, manufactured by Buick. The Special Sport Sedan is part of Buick's Series 40 family of cars. It is powered by a naturally aspirated engine of 4.1 litre capacity. This unit features overhead valve valve gear, in line 8 cylinder layout, and 2 valves per cylinder. It has an output of 107 bhp (108 PS/80 kW) of power at 3400 rpm, and maximum torque of 275 N·m (203 lb·ft/28 kgm) at 2000 rpm. A 3 speed manual transmission transmits the power. Buick scored another first in 1939 when it became the first company to introduce turn signals, which did not appear on other car brands until almost a decade later.[ All 1939 models also had a steering column mounted shift lever1938 Buick Sedan . Bodied in Australia by GMHBurgundy 4 door rear wheel drive sedan automobile, bodied, car -
Trafalgar Holden Museum
Vehicle - Holden FE special sedan, July 1956
BY THE time the FJ Holden was replaced with the FE in July 1956, Australia’s own had taken many steps forward. The six-volt electrics were replaced with a 12-volt set-up, the two-piece windscreen was replaced with a single curved item and the skinny 15in rims were replaced with 13x4.5 steelies. Unlike the FX-FJ, the FE was designed locally by an Australian team. The resulting car was much sleeker than the earlier models, being two inches longer in the wheelbase, four inches longer overall and slightly heavier than its predecessor. To compensate, the 132ci grey motor was blessed with another small dose of horsepower thanks to larger valves and improved cylinder heads. Other mechanical improvements included pendulum-style brake and clutch pedals, hydraulic clutch actuation, larger brake drums and recirculating ball (rather than worm and sector) steering. Other great leaps forward included optional heater, indicators, reversing lights, windscreen washers and demister. In knocked down form was the first model to be exported to New ZealandBlack painted special sedan. Added accessories include exterior sun visor, headlight protectors, and on the interior grab handle mounted across the back of the front seatDiecast special sedan badge on rear quarters. Number plate club permit 63450 Hfe special, holden, sedan, car -
Australian Commando Association - Victoria
Vehicle - Folboat Restored On loan to Special Forces HQ SYDNEY
-
Queenscliffe Maritime Museum
Vehicle - Lifeboat, A McFarlane and Sons, Lifeboat Queenscliffe, 1926
QUEENSCLIFFE was built in 1926 to a Royal National Lifeboat Institution (RNLI) design called the Watson Class. The double-diagonal planked vessel was built by A McFarlane and Sons in Port Adelaide SA, commissioned on the 6th of March 1926, and then officially named and launched on the 9th of April 1926. The original Wayburn petrol engine was replaced with a Gardner diesel. This gave QUEENSCLIFFE a top speed of 7.5 knots with a range of 350 miles. The equipment carried aboard included a VHF Radio Telephone, HF radio transceiver, visual signals, life rafts, hand rocket gun, flare gun, generator, search light and first aid supplies. In the tradition of many shore based lifeboats, QUEENSCLIFFE had its own shed and slipway and was always ready for launching when required to go to sea in response to an emergency call. Its area of operation included 'the Rip' at Port Phillip Heads and the Bass Strait seas immediately offshore. She was taken out of service in 1976 by the Marine Board of Victoria and subsequently offered to the Borough of Queenscliffe for care and display. The Lifeboat is listed on the Australian Register of Historic Vessels (ARHV). During her 50 years of service the Queenscliffe attended many calls for assistance both inside and outside the Heads. Some of the vessels and calls for help the lifeboat attended were: 1960 - Army Commandos lost in the Rip 1967 - The search for the late Prime Minister Harold Holt 1974 - The last attendance to a vessel was to the Brisbane Trader which was on fire The shed which housed the lifeboat is located on the Queenscliff 'New' or 'Steamer' Pier (built in 1884). This shed includes the internal section of the slipway used to launch and retrieve the lifeboat. The external slipway and some other structures associated with the lifeboat shed have been removed. Originally fitted with two masts, the stern mast being removed in the 1960's. A retractable centre plate was used when under sail. Delivered with an 80 hp Wayburn petrol motor which was later replaced by a 72 hp Gardiner diesel. Top speed of 7.5 knots and a range of 350 miles.QUEENSCLIFFE is a wooden lifeboat built in 1926 in South Australia. It has a long association with the Victorian port of Queenscliff. It was manned voluntarily by their local fishermen and is therefore closely attached to families of the Queenscliff community. It is a rare surviving example of the coastal shore-based lifeboats that were based around the Australian coastline.The lifeboat 'Queenscliffe' a Watson Class LifeboatQueenscliffelifeboat, rescue, watson class boat -
Flagstaff Hill Maritime Museum and Village
Vehicle - Vessel, Lifeboat Warrnambool, 01/09/1910
The construction of the lifeboat ‘Warrnambool’ began 15th September 1909 and was completed almost 12 months later, 1st September 1910. It was built at the Government Dockyard in Williamstown, Victoria, along the lines designed by the Great Britain’s Royal Lifeboat Institution, and included whaleback decks fore and aft, mast and centreboard, and rudder and tiller hung from the sternpost. It could be propelled by both sail and oar. At that time Captain Ferguson was Chief Harbour Master and Mr Beagley was foreman boat builder when he and his fellow workmen built the boat. The boat was described as “… a fine piece of workmanship and does credit to her builders and designers…” It had all the latest improvements in shape, disposition of weight and watertight compartments, and it had space for a large number of people in addition to the crew. It appears that 'H Meiers' whose signature, along with building dates, is pencilled on a concealed timber 'plaque' in the hull, was involved with the building of the lifeboat. It is interesting that the ‘Melbourne Directory’ of 1911, published by Sands and MacDougal, lists McAuley and Meiers, boat builders, Nelson Place foreshore, between Pasco and Parker Streets, Williamstown, (Victorian Heritage Database, ‘Contextual History, Maritime Facilities’), It is probably the company of the person whose name is inscribed on the lifeboat plaque. Flagstaff Hill’s documentation also mentions that the keel was laid at ‘Harry Myers, boat builders, Williamstown, Melbourne’ – the name ‘Myers’ can also be spelled ‘Meiers’, which could be the same person as the Meiers in “McAuley and Meiers” (as mentioned in genealogy lines of Myers). The new lifeboat, to be named ‘Warrnambool’ was brought to town by train and launched at the breakwater on 1st March 1911 using the Titan crane (the old lifeboat built in 1858, was then returned to Melbourne in 1911). This new lifeboat was stationed at Warrnambool in a shed located at the base of the Breakwater, adjacent to the slipway. A winch was used to bring it in and out of the water. The lifeboat ‘Warrnambool’ was similar in size to the old lifeboat but far superior in design, build and sea-going qualities such as greater manoeuvrability. The ‘self-righting, self-draining’ design was “practically non-capsizeable” and even if the boat overturned it would right itself to an even keel and the water would drain away. The hull was built of New Zealand Kauri, using double diagonal planking, laid in two layers at right angles, with a layer of canvas and red lead paint between the timbers to help seal the planking. It has “… plenty of freeboard, high watertight spaces between the deck and bottom… through which pipes lead…” The backbone timbers were made of Jarrah. The lifeboat Warrnambool was one of several rescue boats used at Port Fairy and Warrnambool in early 1900's. In late 1914 the Warrnambool lifeboat and crew were used to help find what was left of the tragic wreckage of the Antares, and were able to discover the body of one of the crewmen, which they brought back to Warrnambool. Between 1951 and 1954 the lifeboat was manned under the guidance of Captain Carrington. He held lifeboat practice each month on a Sunday morning, to comply with the Ports and Harbour’s request that lifeboats be manned by a strong and competent crew, ready for action in case of emergency. In the early 1960’s it ended its service as a lifeboat and was used in Port Fairy as a barge to help dredge the Moyne River, bolted to the Port Fairy lifeboat. Flagstaff Hill obtained the Warrnambool in 1975. In 1984 it was on display at Flagstaff Hill Maritime Village, Warrnambool. On 23rd May 1990 she was lifted from the water and placed in a cradle for restoration. The name ‘WARRNAMBOOL could be seen faintly on the lifeboat before it was restored. It was during the restoration that Flagstaff Hill's boat builder discovered the 'plaque' inside the hull. A copy of the blueprint plans has the name “V.E.E. Gotch” printed on it. His advertisement in Footscray’s ‘Independent’ newspaper of Saturday 11th May 1901 states he is “Principal and Skilled member (Naval Architect) to the Court of Marine Inquiry of Victoria and holds classes for naval architectural drawing and arithmetic.”The lifeboat WARRNAMBOOL is significant for its half century service to the local community as a lifesaving vessel. She was also used to help retrieve the body of a shipwrecked crew member of the ANTARES. Lifeboat "Warrnambool", a wooden, clinker hull, 'self-righting, self-draining design, single mast, pivoting centreboard. Complete with sail and yardarm. A 'plaque' was found inside the hull of the lifeboat, made of untreated wood, disc-shaped with one straight edge (Diam 15.5cm), inscribed by one of the boat builders in pencil script "Life Boat Start building / 15/9/09 - complete 1/9/10 / (signature looks like H Meiers) / Boat Builder)."'Plaque' inside body of boat is inscribed in pencil, script writing "Life Boat Start building / 15/9/09 - complete 1/9/10 / (signature looks like H Meiels) / Boat Builder)." flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lifeboat, life boat, vessel, life saving, 1910 vessel, port fairy, boat builder plaque, rescue boat, beagley, williamstown, government dockyard, v.e.e. gotch, royal lifeboat institution, captain ferguson, meiers, nelson place, non-capsizeable, self-righting, titan crane, double diagonal planking, captain carrington, barge, antares, self righting, crew of twelve, capacity of 30 survivors -
Queenscliffe Maritime Museum
Vehicle - Sailing dinghy heron
The Heron is a two person dinghy that is sailed in all states of Australia. The Heron was designed in the early 1950s by Jack Holt in the UK. The class was introduced to Australia in the late 1950s and has flourished in its new home.Heron sailing dinghy. Hull No 678, first built in Australia, Gaff rigged, home built early 1950sDee Kay -
National Vietnam Veterans Museum (NVVM)
Vehicle, Bell UH1 Iroquois Helicopter, 1960 approx
Bell UH1 Iroquois helicopter modified by the RAAF. It is known as the Bush Ranger. It was used in Vietnam from 1962-1975. Display aircraft AS-110 was used in Vietnam from Dec 1969 to 1971.9 Squadron badges on cockpit doors, RAAF & Kangaroo on tail boom, 110 & Bush Ranger on the nose.hueycobra (helicopter), iroquois helicopter, bush ranger -
National Vietnam Veterans Museum (NVVM)
Vehicle, M2 A2 105mm Howitzer, 1966 approx
General purpose towed field artillery gun.S/N 10515-66-142-8111howitzers, 105mm howitzer -
National Vietnam Veterans Museum (NVVM)
Vehicle, SWB Land Rover, 1967
Short wheel based Land Rover.land rover -
Churchill Island Heritage Farm
Vehicle - Sulky wheel left
These wheels belong to a lightweight horse drawn cart called a Sulky which usually feature just one seat to carry the driver. They were designed as a fast method of personal transport, especially in rural areas. More modern and streamlined versions are these days used in the sport of harness racing.One of pair of matching black sulky wheels with red hubsfarm machinery, wheel, horse drawn vehicle, sulky, churchill island -
Fire Services Museum of Victoria
Vehicle - Fire Engine - Pumper "SEC Dodge", "SEC Dodge"
Maufactured for State Electricity Commission of Victoria (SEC) fire brigade at Yallourn township serving the nearby open cut brown coal mine, briquette manufacturing plant and electricity generating station. Donated to FSMV 19??, on closure of Yallourn Fire Brigade preparatory to closure of township to allow extension of open cut mine over township site.Unique only fire engine of design ever made.Pumper fire engine State Electricity Commission of Victoria (SEC) Fire Brigade, Yallourn, Vic Front mounted pump, ?, ? lpm [ ? gpm] Seat for 4 crew open cross mounted behind cab Ladder, ? m [ ? feet] Water tank ? l [ ? gall] Hose reel ? m [ ? feet] Current vehicle registration - CH6281 SEC logo on both doors Y F B on compartment door on both sides of bodyfire engine, fire engine pumper, dodge fire engine, dodge, yallourn fire brigade, sec fire brigade, yallourn, sec -
Trafalgar Holden Museum
Vehicle - FJ Holden
The FJ came along after five years of producing the 48-215 (FX) and was basically the same car with a few minor alterations to the body. Minor alterations introduced that year. The vertical grille was replaced by an elegant finned and detailed version, and the new chrome cone shaped hubcaps looked the part. There were new bright metal body decorations, 5.90 x 15 tyres, new bumpers and wonderful new chrome fins placed on the rear mudguards. And at last the Holden could be seriously optioned. For example, the 'Special' featured armrests, deluxe leather seat trim, front door courtesy switches, chrome instrument surrounds, black knobs with chrome inserts, dash facia grille extending to the glovebox, rear passenger assist straps, window winders, a cigarette lighter and (for the first time) came in a two-tone finish. The first Holden to be exported to New Zealand, 327 were shipped.Has two tone grey finish , four door sedan, tail fin mounted reflectors on each rear mud guard.Holden specialvehicle, holden, 1953, car -
Trafalgar Holden Museum
Vehicle - Holden model FB sedan, 1960 - 1961
The FB was promoted as being longer, lower, more spacious and more powerful than the FC model, but in reality it was only slightly so on each count overerall length was 5.5 inches (140 mm) greater, although the wheelbase remained the same. The engine bore was still 3 inches (76 mm), the last model with that specification. Engine capacity was 138 cubic inches (2.16 L) but the compression ratio was raised. However, the resulting extra 4 brake horsepower (3 kW) of power did not compensate for the greater weight of the FB, so performance was inferior to that of its predecessor. Changes were also made to the brakes, front coil springs, air cleaner and clutch. Obvious styling differences were the lower bonnet, finned rear mudguards with new taillights (on the sedans and wagons only) and a wrap-around windscreen. Seating was improved, as was the instrument panel. A refinement of the FC model but appearance significantly changed with a wraparound windscreen, lower bonnet and finned rear guards.. This vehicle was purchased in NSW The interior was in excellent condition bur required extensive exterior work to bring it back to its original condition, It had a mileage of 8500. A refinement of the FC model but appearance significantly changed with a wraparound windscreen, lower bonnet and finned rear guards. It was the first Holden with acrylic paintwork.Two tone grey body , four door FB Holden sedan. Finned rear mudguard,. Holden Special Registered number 63452-Hholden, automobile, 1960, car -
National Vietnam Veterans Museum (NVVM)
Vehicle, M113 Armoured Personnel Carrier, 1958 approx
Armoured personnel carrier used by the Australian Army in Vietnam.ARN - 134253armoured vehicles, military, armoured personnel carrier, m113 -
Trafalgar Holden Museum
Vehicle - Motorcycle side car, 1913
Single seat motorcycle side car used primarily for message carrying during WW1As built by Holden and Frost from 1913, during WW1Cream coloured single seat motorcycle side car mounted on a black frameOULDING SPECIAL PAT'N'Dmotorcycle, single seat, sidecar -
Flagstaff Hill Maritime Museum and Village
Vehicle - Wagon, Early 20th Century
This wagon is linked to Mr Stanley James Bell via his father Mr John Bell, who owned "Warrumyea" at Wangoom. It is believed that Stanley grew up and worked for his father at this property, eventuality inheriting his father's death in 1920. This wagon was likely used at Mr Stanley Bell's property “Warrumyea” at Wangoom around 1920-1940. The wagon was donated in 1984, at which time it was noted as having a brass plate inscribed "Jas", which name Stanley was known by. Also, a painted on the wage was “S J Bell Wangoom”. Remnants of the original paint colours of blue and yellow show on the photograph, which was taken at the time of cataloguing. Mr John Bell Snr from Plymouth, England, arrived in Portland, Victoria, around 1860. He had served in the British navy as a lad for a number of years. On arriving in Australia he travelled to the Wangoom district where he lived for many years. Mr J Bell worked for 20 years as herd manager at “Wangoom Park”., for Mr F Tozer (1843-1954), one of the original pioneers of the western district. He went on to pursue dairying and general farming at his property “Warrumyea” Wangoom. Bell’s son Stanley James Bell went to the Wangoom School. His first reader from this school, published in 1909, has his name inscribed in the flyleaf “Stanley J. Bell, Warrumyea, Wangoom” and is now in the collection of the Warrnambool & District Historical Society. Stanley went on working the property “Warrumyea” and eventually purchased “Wangoom Park” in 1956, where his father had been employed years before. Mr S J Bell died in 1968.The wagon is significant for its association with the farming history of Wangoom and the Warrnambool area in general. Also, the wage is significant for its association with one of the early families that settled in the Warrnambool area and their contribution to the dairying and general farming industries that sprang from their efforts. The wagon has a good provenance linking it to Mr Stanley James Bell and is also a good example of how goods were transported using horse-drawn vehicles at the beginning of the 20th century.Four-wheeled wagon or cart,12 spokes in each wheel, wooden axle with rear hub brake. Hinged and chained tailboard. Wheels have metal rims. Metal frame and wooden superstructure. Wagon has two pairs of staves. Wooden shelves, one missing with turntable. Small toolbox in front. Made by Kelly and Preston of Ballarat. Metal nameplate of the owner attached, "Jas" (S J Bell of Wangoom).. Original inscription, now obscured, was painted “Kelly and Preston Builders Ballarat”. Metal plate inscribed "Jas", and "S J Bell Wangoom". flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wagon, sj bell, stanley james bell, wangoom park, warrumyea, first reader, john bell 1830-1920, stanley james bell 1904-1968, warrnambool pioneers, f tozer, western district, kelly and preston of ballarat