Used in the farming industry around Orbost to cut silage or hay. Used to cut compacted hay or silage prior to the baling of hay or silage, until the late 1940s.A typical tool from the Orbost farming industry pre 1950.A large coarsely serrated flat metal blade set with two wooden handles.silage-knife agricultural-implemement

Used for splitting wooden palings used in the construction of paling fences. Dates prior to palings being mass-produced by mechanical saws in timber mills.A rectangular iron blade attached to a wooden handle. The bottom of the blade is the sharp edge. tool hand-tool paling-knife split-timber

These photographs were taken just after the McKillop's Bridge was completed after the flood damage. The current McKillop’s Bridge was built by the Country Roads Board in two stages between 1931-36, during which its height was raised after the original bridge superstructure was washed away in record floods of January 1934, prior to its original official opening. In its reconstructed form the original concrete abutments were turned into additional piers and the welded-steel trusses were cantilevered back over them to meet the new higher road approaches. It is sited at McKillops Crossing, named after pioneer overlanding squatter George McKillop who crossed here in 1835. This was a stock crossing place for almost a century before the bridge was constructed. (info. from Victoria Heritage Register)This is a pictorial record of the history of McKillop's Bridge, in itself of historical significance for its association with Victoria's long and important pastoral history, its technicl significance and aesthetic significance.Three black / white photographs. 3133.1 shows the approach to a washed away bridge. 3133.2 is of a bridge over a river with men clearing debris. 3133.3 is a close-up showing the wreckage of the bridge.mckillop's-bridge snowy-river flood-damage-1934

This is a photograph of McKillop's Bridge probably taken just after its rebuilding. The current McKillop’s Bridge was built by the Country Roads Board in two stages between 1931-36, during which its height was raised after the original bridge superstructure was washed away in record floods of January 1934, prior to its original official opening. In its reconstructed form the original concrete abutments were turned into additional piers and the welded-steel trusses were cantilevered back over them to meet the new higher road approaches. "McKillops Bridge was Heritage listed due to its social and technological significance – the steel trusses' arc-welded construction technique was a pretty big deal in the 1930s. It was once an important route for cattlemen, who used the ford across the Snowy in the years preceding the bridge's existence"This is a pictorial record of McKillop's Bridge just after its construction.A black / white photograph of a wooden bridge across a river. At the bottom right is a man with his back to the camera. He is looking at flood debris on the bank. At the bottom left are two men near a pylon.on back - McKillops Bridgebridge-mckillop's snowy-river-bridge

All of these photographs were taken prior to 25th November, 1876, the official opening and crossing of the current Snowy River Bridge. Gary Downey, an Orbost Apeian, did a "De Groot" and crossed the bridge on horseback prior to the official cars crossing the bridge to signal the opening of the new structure. There was a closing ceremony for the old bridge with a group arriving in a 1927 Chrysler, owned by Apexian, Peter Dreverman. This was watched by groups of school students. Some of the Apex members, including Jim Duggan, Noel Smart and Pat Hall, dressed in formal attire to speak to the audience.This event was organised by the Apex Club of Orbost.The Apex Club of Orbost was a volunteer service club which contributed to the Orbost community. A declining population has led to the demise of many social groups in the area.Ten black / white photographs related to the unofficial opening of the Snowy River Bridge at Orbost. snowy-river-bridge-1976 apex-club-orbost ceremony

This item was worn by Sarah Archer, born 9.11.1881, and her daughter Irene Jean Maiden, born 1.7.1923, She lived in Orbost all her life having been born at the oOld Orbost Hospital in Nicholson Street. Irene died aged 86. Until well into the 20th century, the corset was an essential element of fashionable dress. Corsets were worn by women (and much earlier by men) to enhance their figures and to hold their stockings in place. Although still sometimes used they were mainly used prior to the making of pantyhose approximately 1960. A corset made of heavy apricot / pink cotton fabric . It has back tape acing through metal eyelets, and slide hooks. It has suspender straps with clips attached to the bottom of the corset. The stays, possibly whalebone, are sewn vertically into the fabric.on label - in red ink - "Liberty Reg'd "6/2815 D" small below waist size 32" exactcostume-women corsetry clothing

In 1893, a group of Orbost farmers formed together to initiate the Orbost Butter Factory. The first factory was built in Lochiel Street and was a wooden building. In 1916, a new building was constructed on Forest Road. This was a more substantial brick building which had its own power source. Electric power, mainly for lighting was supplied to the developing township of Orbost by the Butter Factory. This docket is an invoice for the supply of power to the household or business of C. Tomlinson in 1952. The Butter Factory power was the only power to Orbost prior to the 1962 when S E C power came to Orbost. An invoice from a major business in Orbost which supplied power to the town for the first 50 years of the 20th Century. A laminated copy of an invoice from Orbost Butter & Produce Co Ltd. Black print on white paper. Telephone 88 if supply defective Orbost Butter & Produce Co Ltd To Mrs C Tomlinson, 2 May 1952. Lighting15/- Power 5/3 Meter rent 1/- Account rendered 6/13/3orbost, electric power, orbost butter factory, c tomlinson

Terry Kane and Richard Carter were the authors of the short historyType written notes and plans pertaining to the land titles and history of the Ringwood Secondary College site from 1905, prior to the land being sold by the Borough of Ringwood in 1954 to the Education Department. Transcript of covering letter from Richard Carter to Mr T Kane dated 16 November 2012 - "Re: Ringwood Secondary College As we discussed recently, I have done some research into the history of the site. Going back to 1905, the site, then 26 acres one rood 37 perches, was in the name of Walter James Anderson of 61 William Street, Melbourne, Accountant - most likely a speculator. Title transferred to Theodosia Anderson of 167 Collins Street, Melbourne, Artist - possibly his son - In 1907. Theodosia Anderson was thus the owner when on abortive subdivision Into "110 Splendid Home Sites" as "Bedford Park Estate, Ringwood" took place In 1924, creating Anderson Street, Joyce Street, Adams Street and Graham Road, all of which sank without trace. Theodosia Anderson died In 1933, leaving the property to John Blair, Solicitor of Melbourne and Annie Benson of Melbourne, widow, until title ultimately passed to The Mayor, Councillors and Burgesses of the Borough of Ringwood In 1946. Title was then spilt Into three with 14 acres 0 rood 11 perches being transferred to the Minister of Education on 1954 followed by a further 2 acres 1 rood 26 perches to the Minister In 1956. The balance of the land remains In the ownership of the now Maroondoh City Council as Bedford Park. It Is Interesting that at no stage did any of the land belong to the Commonwealth of Australia, notwithstanding that I always understood It was the site of the P.M.G. Workers Camp after the War. Perhaps the P.M.G. utilized the site by arrangement with the borough of Ringwood; perhaps the camp was on the opposite site of Hill Street (Government Road). More research Is needed on this point. Yours faithfully, CE CARTER & SON PTY LTD Richard Carter Managing Director"

One sepia and two black and white photographs of houses with prices in pounds, indicating prior to currency decimalisation in 1966.Photograph by The Ringwood Studio, Shop 14, Ringwood Shopping Centre. Phone WU7609 Copyright.

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure.This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools.A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl.woodwork tools brace-ratchet

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure.This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools.A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl. The drill bit is jammed and the chuck is rusted.woodworking tool brace-and-bit carpentry

This insulator was used on phone wires. Insulators were originally designed to keep the wires linking telegraphs and telephones insulated from the wooden poles that held them aloft. Prior to 1925, Australia relied solely on insulators imported from other countries. Glass insulators were first manufactured in Australia in c. 1926 by Australian Glass Manufacturers. Their factory was, and still is, located on South Dowling Road in Sydney. Australian Glass Manufacturers (A.G.M.) had developed a toughened type of glass very similar to Pyrex glass. Since the Pyrex name could not be used due to trademark infringements, they called their glass AGEE for Australian Glass. Many fruit jars, insulators, pie dishes and other glass items were manufactured with this AGEE trademark during the 1926 to 1940 period.Glass insulators are rapidly becoming a thing of the past in Australia with open-wire communication lines rarely existing near metropolitan areas. The remaining open wire lines are being abandoned and dismantled everywhere with very few insulators being saved as interest in them in Australia is quite limited. (ref Australian Insulators web-site). This item is an example of a piece of equipment which has been superceded.A glass telegraph line insulator of double umbrella shape. Glass is coloured purple - AGEE 30 Insulator. It is a tapered cone of thick glass. The inside top is threaded for screwing onto the metal piece on a wooden cross bar.Embossed on outside of bell: "AGEE 30"insulator-glass agee a.g.m. communications telegraphy

This is a photograph of Annabella McKenzie who trained at The Royal Melbourne in the 1890's. The Royal Melbourne Hospital was the first hospital in Victoria – established in 1848 to serve the young and thriving community of Melbourne. Prior to the transfer of nursing education to the university sector, nurses were trained in a course of instruction in hospital nursing schools that awarded a certificate in general nursing. These courses were generally for a three-year period, and nurses were paid employees of the parent hospital. Annabella Mckenzie Fisher was born into the Mckenzie family and married into the Fisher family. She married Fisher James Fisher, a Lochend farmer.The Fisher family was a very early Orbost farming family.A hand-coloured photograph in an oval shaped wooden frame. It is of a woman in a nurse's uniform of a dark coloured dress with a white bib apron and black belt. The cuffs of the long sleeved dress are white. She is wearing a white cap. The oval frame is painted gold and is decorated on each side with flowers in relief.On back in pencil - Anna Bella McKenziehealth nursing fisher_annabella-mckenzie royal-melbourne-hospital

Prior to the 1960s, hats were worn by all men. Aluminium hat stretchers were generally in use from the 1920’s. The hat was placed on the aluminium dome shaped piece. When the handle was turned, the dome section split vertically, one section moving away from the fixed half. A graduated scale along the side indicated the size. This item was possibly used in the hat factory in Orbost. Stuart Hats commenced manufacturing hats in about 1948 and closed their factory in Orbost around 1953 probably because of the high transport costs. The company's head factory was in Melbourne. The hats made in Orbost were sold all over Australia as well as in Melbourne at Myers and David Jones. The building became first a Dry Cleaners and then a private home.This item was possibly used by Stuart Hats which was a significant manufacturing business in Orbost in the 1950's employing nearly 20 local people.A hat stretcher consisting of an aluminium dome-shaped piece (on which the hat was placed) and a metal winder. It has been mounted onto a wooden baseOn wooden base : "Restored by John Mundy"millinery hats hat-stretcher

Black and white photographTyped below photograph, "Main Street - Shops and Coffee Palace just prior to demolition - 1965".

Exterior view of Ringwood Gospel Chapel in Warrandyte Road, Ringwood, prior to relocation in 1974.Written on back of photograph, "5.10.74". The board on the Church says, "A warm welcome is extended to all. To attend our services shortly to be conducted in a new brick Chapel ... being erected in Tamar Street, Ringwood (off Warrandyte Road)."

Black and white photograph showing made road. Telegraph pole on right of picture. Tall trees to left of photograph. Houses either side of road. Road sign on telegraph pole reads, "Nelson St."Typed below photograph, "Ringwood St. looking south. Ringwood Reserve to left of row of trees in centre."

Black and white photograph of road. Trees line left of street. Power pole to right of photograph with signage reading, 'Court House' and 'Bourke St.' Police station sign to right of picture.Typed below photograph, "Ringwood St. looking south. Ringwood Reserve on left".

Typed below photograph, "Ringwood St. - The building of the Church of England and the vestry. Looking towards Civic Place. Eastland Car Park Civil Works on left".

Biscuit dough was put into the forcer/case/cylinder and the wooden pin pressed down to force dough out as a shaped biscuit. This would have been used in use in an Orbost home in the mid 20th century.This item is representative of kitchen utensils in common use in working class kitchens in 20th century prior to the common availability of packaged biscuits.Biscuit paste forcer made up of a metal barrel with a ring for hanging at top and a wooden plunger with a knob handle on top. This is shaped like a rolling pin. Biscuit mix is forced through the end of the tube to create fancy-looking biscuits.domestic kitchen food-technology biscuit- forcer baking appliances

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure. This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools. A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl

Davey's Hotel at Miners Rest was built sometime around 1850, and Mary Tait was the original Licensee.The gentleman on the white horse is Harry Telford, who was with Phar Lap in America when the horse died.Names of the other men are not known. The photo is dated "circa 1916 -17" and originally came from a lady in New Zealand.The Hotel was de-licensed in 1940. Mary Tait (nee Marion Sutherland) was the second wife of William Tait, who was the licensee of the Derby prior to his death 7 October 1862.His widow Mary the took over the license of the hotel.Photo shows lifestyle of the 1850's.Black and white photo depicting Davey's Hotel in Miners Rest with some of the locals.Davey's Hotel / Derby Hotel.miners rest 1850, davey's hotel, harry telford, mary tait licencee

Photo depicts members of the Ballarat Shire Council in 1994 at the Commemorative Meeting Prior to Amalgamation with City Of Ballarat. Front row (L to R) Mr. I. R. Cowie. Deputy Shire Engineer ; Mr. R. W. Hayles, Shire Engineer; Cr. D. N. Vendy, Shire President; Mr. J.W.M. Johnson, Shire Secretary; Mr T.J. Barrington, Deputy Shire Secretary. Back Row (L to R ) Cr. R. Kinnersley, Cr. A. Cormick, Cr. D. A. Baird, Cr.G.H. Spittle, Cr. J.D.White, Cr. G.M.Caldwell, Cr. M.F.Beaumont. Cr. W. M. Flynn, Cr. R.A. McDonald, Cr. R.J. Fewster, and Cr. B.L.Hughes.To commemorate the final council meeting of the Shire of Ballarat prior Council Amalgamation with the City of Ballarat.Coloured Photo on cream coloured mount with Shire of Ballarat Crest and title above photo and names at the bottom.SHIRE OF BALLARAT COMMEMORATIVE MEETING. MONDAY 2ND MAY 1994.shire commemorative meeting 1994.last ballarat shire councilors.

This small hand-held tool was used in the maize industry in Murrungowar (Orbost District) during 1900-1960s. Prior to machine harvesting coming about in the 1960s, each cob of maize had to picked by hand using this tool. Maize growing was a huge industry in the Orbost district and the job of picking the maize involved hand labour by many employees. This small hand-tool would have been common, but is now rare. This particular tool was owned and used by Nelson Northrope (Orbost) in the early 20th Century and used at Murrungowar by Frances Eilman (nee Somerville). A highly significant small hand tool associated with the maize industry. This item is rare. A small hand-held metal and leather tool. A metal 'knife' has a curved shape and is attached to 2 leather straps which are connected by a small buckle. maize growing, agriculture, orbost district

In 1848, 43-year-old John Clarke launched a cutlery business in Harvest Lane in Neepsend, Sheffield UK. Clarke entered the trade late in life he was indenture and apprenticed to Octavius Twigg, a razor maker. Clarke was granted his Freedom in 1856 and began using the trademark 'NEVA'. By the 1860s, Thomas Clarke's son by his wife Elizabeth had joined the firm. When John Clarke died at his home at Augusta Place, Rock Street, Sheffield on 25 July 1873 (aged 68), he only employed six workmen.  By 1881, Thomas had expanded this number to twenty.  He sold a wide range of cutlery and was also an ‘emigration agent’, the Sheffield Independent, of 7th September in 1886 had an article published stating Thomas helped to recruit personnel from England for cutlery centers in America.  In 1893 Clarke’s showroom displayed miniature knives from '5/16ths-inch long to the most expensive sportsman's knives, that were gold and silver mounted.  Table knives and carvers were also manufactured (or factored).  Agencies were opened in London, New York, and Melbourne.  Besides ‘NEVA, the ‘EXPRESS’ and ‘RING’ marks were used on razors; and Clarke’s marketed the American ‘GEM’ safety razor.  By 1901, the firm had moved to Mowbray Street, where its Mowbray Works overlooked the River Don. Thomas Clarke died at Harrogate on 26 April 1902, aged 62, and was buried in the same Burngreave cemetery as his parents.  Thomas’s sons, John Roome Clarke (1860-1925) and Thomas Edward Clarke, were directors, another son George William Clarke was a shareholder. John Roome Clarke died on 3 February 1925, aged 64  his son, John Clarke, of Crimicar Lane, remained as the senior partner.  Clarke’s was one of the last producers of hand-made pocket knives and it also produced a large output of sheath knives for scouting associations. The firm was liquidated in 1964, but the company name was resurrected and Its last address after 1980 was at 65 Garden Street Sheffield.  The company trademark passed on to Meteor Industries and then to Egginton Ltd. Weber & Co: The Clarke company purchased or (factored) many of its blades for razors and knives from Weber & Co of Solingen Germany. The full name of the firm originally was Jowika Stahlwarenfabrik Eugen Weber & Altenbach KG. It was founded in Solingen prior to 1928, under the name Johann & Wilhelm Kleinewefers GMBH, Messerfabrik. JWK for short, hence JoWiKa. The company was sold to Eugen Weber in the 1930s. Weber was married to a woman named Altenbach, from a family that manufactured innovative low-priced pocketknives, as well as other cutlery items. In 1960 Weber opened a branch factory in Listowel Ireland. It was sold to Albert M. Baer of Imperial Schrade in 1978. The Listowel factory was closed about a year and a half before the U.S. Schrade factory closed in 2004 and the Jowika factory in Solingen had closed in 1984.An item with an interesting manufacturing history from the 1930s showing how one man can grow a business into a successful concern that made quality products that stand the test of time.Razor metal folding blade with horn handle in its original cardboard box Inscription Made by John Clarke and Son England. "Champion" razor. On box " The Champion 10/6d" and "Weber Lohmann & Co SOLINGEN".flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

In early civilization's cereal grains such as maize, wheat, barley etc. were stored in large airy buildings, often raised up from the ground to reduce infestation by pests and vermin. Ancient Egyptian and early Hebrew writings include reference to such buildings. Smaller quantities of food were stored in baskets made from woven grasses or leaves. In more recent times but prior to the invention of the refrigerator many food products were stored in the home as preserves or pickles, often in heat sealed jars. Dry food items were stored in vermin proof metal containers and could be found in any early colonial kitchen. Items such as coffee, tea, rice and sago were stable food types and needed longer term storage and a higher degree of protection from vermin and the elements, a common material used during this time was sheet metal or tin such as is used today in a common form of storage the biscuit tin. An early example of colonial food storage used in a domestic setting, it is interesting to note the subject items have provision to be locked. This indicates the value early colonial settlers placed on the contents and used to prevent pilfering. The subject items are now sought by collectors. Canister set; set of four canisters. Cylindrical matching kitchen storage tins with hinge lid that has a latch closure, and a folding handle on top of lid. Canisters are painted brown and the body has a graphic of a scroll in gold with printed label of contents. The canisters range from small to large, "COFFEE", "TEA" , "SAGO", " RICE" (respective RNs 163.1, 163.2, 163.3, 163.4)Respectively labelled "COFFEE," "TEA," "SAGO," "RICE" flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, flagstaff hill maritime village, great ocean road, canister, canister set, rice canister, kitchen canister, food storage, domestic item

A mass produced unbranded utilitarian item made for domestic use no history or provenance currently available, design indicates item made before 1950Item at this time cannot be associated with an historical event, person or place, provenance is unknown, item assessed as a collection asset as made prior to 1950.Stoneware mixing bowl round cream with pouring lip and decorative scallop relief around bodyNoneflagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, flagstaff hill maritime village, great ocean road, bowl, ceramic bowl, pouring bowl, kitchen ware, cooking ware, ironstone bowl, salt glazed, mixing bowl

No dust cover. Front cover is light green. At the top of the cover is an illustration of three ships in black. Under the top illustration is the title of the book in black. In the center is an illustration of a boy and a girl sitting opposite each other, both reading books. At the foot of the cover is an illustration of an open book with a grape vine flowing across it. Underneath are the words 'Herbert Strang's Library in black. The title, author and publisher are in black on the spine.fictionMoby Dick is the story of a man, a ship and a whale. It is a classic novel that was originally written in 1851.moby dick, whale, whaling, whaling ship, herman melville, fiction

Hardback. Dark brown cover with the title in gold lettering. There is also a border in gold decorating the outer edge of the front cover. The spine is also decorated in gold along with the title and the volume number.non-fictionA history of the various colonies and districts of Victoria from the time of the discovery of Australia through until 1888.melbourne, victoria, pioneers, colonisation, history, fauna, flora, banking, finance, medicine, western district, south-western district, wimmera district, geelong district, ballarat district, avoca district, coliban district, campase district, loddon district, lower goulburn district, upper goulburn district, ovens district, north-east district, gippsland district, mornington district, westernport district, upper yarra district, evelyn district, bourke district

This foot grip was made and owned by Frederick William McDowell (Fred) (1880 to 15-6-1967). It would be been joined to the stafe or frame of a jinker and used to step up from the ground and onto the seat. He was a wheelwright by trade. He made and repaired vehicles such gigs, buggies, jinkers, sulkeys, spring carts and farm wagons. His workshop was on the corner of Cramer Street and Raglan Parade in Warrnambool., previously the site of Fotheringhams, and after McDowell's, and still in 2023, occupied by Reece Plumbing Fred's workplace prior to retiring was at Bryant & Waterson's in Kepler Street, opposite the Criterian Hotel, making rubber tyred horse-driven farm wagons.This jinker's foot grip id part of a jinker or two-wheeled carriage. It is a rare item, made by a local wheelwright Frank McDowell who operated his buggy making and repair business in Warrnambool's CBD in the early twentieth century. It is an example of the equipment used on horse-drawn vehicles for safety and convenience.Foot grip, iron with silver plate finish. Rectangular metal plate with textured crossed over diagonal lines on the top surface and inset rectangles with impressed text. the curved and shaped ends have a drilled round hole. the length of the plate is an inverted 'v' shape towards the base. Made by F. McDowell, Warrnambool."F McDOWELL" "WARRNAMBOOL"flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, fred mcdowell, frederick mcdowell, wheelwright, gig, buggy, jinker, sulkey, spring cart, farm wagon, 2-wheeled cart, horse cart, horse cart parts, jinker buggy, transport, vehicle, horse drawn, horse jinker, bryant & waterson, jinker part, jinker foot grip, step, foot plate, horse cart part, stafe, 2-wheeled carriage