Probably acquired for use in Telegraphy courses run at the Ballarat SChool of Mines between 1875 and 1893. Telegraph relays amplified electrical signals in a telegraph line. Telegraph messages traveled as a series of electrical pulses through a wire from a transmitter to a receiver. Short pulses made a dot, slightly longer pulses a dash. The pulses faded in strength as they traveled through the wire, to the point where the incoming signal was too weak to directly operate a receiving sounder or register. A relay detected a weak signal and used a battery to strengthen the signal so that the receiver would operate. This relay was made by the firm of Charles T. and John N. Chester, two brothers who successfully partnered in New York City. Charles (1826-1880) founded the firm and provided the expert telegraphy knowledge while John (1820-1871) kept the books and managed the business operations.(http://americanhistory.si.edu/collections/search/object/nmah_706518, accessed 25/01/2018)Electromagnetic relay device used in telegraphy. The working parts mounted on a brass plate, attached to a wood base. Equipped with four terminal posts. Adjustable contactor mechanism. This electromagnetic Relay Device was used in Telegraphy at the Ballarat School of Mines. After a special meeting of the Ballarat SChool of Mines Council in 1874, a decision was made to offer instruction in Telegraphy, a subject not directly related to mining. Telegraphy was taught by W.P. Bechervaise, postmaster at Ballarat. On 07 October 1874 the Ballarat Courier correspondent reprted on Telegraphic training: "... these classes ... are a snare and a delusion, as there is scarcely the remotest chance of obtaining employment when the examination has been passed."scientific instrument, telegraph relayer, telegraphy relay device, telegraphy

Pittock Collection : three wrenches, steel construction. Two individual wrenches: * one adjustable wrench , 230 x 80mm, made by the Footprint company, Sheffield, England. * one small (rusted) wrench, 165mm long; made by COES Wrench Co, Worcester, Mass. U.S.A. * One wrench set, for eight pieces (two smaller pieces missing) drop forged steel, made by The Keystone MFG, Co. Buffalo, U.S.A.; folded sheet steel ''case", rusted in places. Wrench 230 mm long x 40 mm wide x 60mm high. Items stored in coach builder's box, reference 13000.1.three wrenches manufacturers as noted

Yields information about the activities inside the depot by the BTPS showing difficulties and the provision of overhead troughing.Set of 7 digital images scanned from 35mm slides of early activities at the BTPS depot c1973. .1 - Noel Forster assisting another member adjust the brakes on a bogie tram inside the depot. .2 - cleaning old paint off a bracket arm with a kerosene blow torch. .3 - repainted trolley pole base at the depot .4 - interior view after the troughing has been positioned. .5 - ditto .6 - view of the depot from the overhead truck - 26, 28 and 40, one road yet to be commenced. .7 - interior view of the depot with workers - Peter Rees, Andrew Cook and Graeme Jordantrams, tramways, btps, trackwork, depot, tramcars, overhead, tram 26, tram 27, tram 40

Two part object. (1) A Slazenger 'Phantom IMF' tennis racquet with open throat, plastic butt cap and handle wrapped with leather. Manufacturer name across base of head. Model name printed along left throat pillar. Plastic butt cap features manufacturers name and cat logo. Logo also featured at base of throat.(2) Full length navy blue vinyl racquet cover with two zippers and printed with manufacturer's name and logo and model name. has woven adjustable shoulder strap. Materials: Metal, Adhesive tape, Plastic, Leather, Ink, Vinyl, Graphitetennis

This cream and green patterned vest is said to have been made for William Herbert Teal as part of his "trouseau" on the occasion of his marriage to Daisy Edith Davis on April 14th 1916 at St. Peter's Church, Merino, Victoria, Australia. It is a handmade waistcoat but it is not known who made it. William Teal was born in 1889 to Elijah Teal and Isabella Campbell Reid in Camperdown, Victoria and after marrying, William and Daisy also lived (and worked as farmers) in the Camperdown area. They had seven children. Daisy died in 1962 and William died in 1975. A wedding portrait of William and Daisy shows William wearing a dark suit consisting of a single breasted coat, trousers, good shoes, gloves and a shirt with a stiff, high collar, however if he is wearing this vest, it is unfortunately hidden under his coat. Although by 1916, men's "ready to wear" clothing were widely available, this waistcoat was handmade (possibly by his mother or sister or future wife) and has been preserved by his family for almost one hundred years. Men's suits in the early part of the twentieth century were predomininantly three piece, consisting of a jacket, vest ( or waistcoat) and trousers made from matching fabrics. On special occasions (such as a marriage) the groom might also wear gloves and have a flower in his buttonhole. Some men liked to wear a watch attached to their waistcoat with a fob chain.This item is of significance as a rare example of a man's vest that was made for a special occasion (William Teal's marriage in 1916) and preserved by his family for several generations.Man's handmade vest with a green and cream patterned brocade front, trimmed with green cord around the edges and featuring four inset pockets (also trimmed with the green cord). It has six buttonholes down the left front edge (plus a hand embroidered buttonhole to hold a fob chain) and six corresponding holes for shank buttons (which are missing) down the right front edge. The back and lining are made from cream cotton fabric. The back has a centre seam and a strap with a metal buckle with prongs (to allow for adjusting the length). The cream lining and back display some discolouration and brown marks.flagstaff hill maritime museum and village, great ocean road, warrnambool, camperdown, merino, teal family, william herbert teal, daisy teal, daisy davis, waistcoat, man's waistcoat, vest, wedding, handmade vest, wedding clothes

Augustus Bostock was the 9th child of Robert & Rachael Bostock of Vaucluse Epping Forest, Van Diemen’s Land. He was only 4 years old when his mother died. He was inspired by his father to seek his fortune in the Western District of Victoria. He arrived around 1850. He married Margaret Aitkin in July 1865. Augustus owned several properties in the district and leased others. He sat on the court of Warrnambool, Mortlake or Hexham as required. He resided at Marramook in Hawkesdale and later moved to Vaucluse in Hopetoun Road Warrnambool, where he died in 1920 at the age of 87. He was involved in many aspects of life in the Western District, racing, cricket, and social activities to name a few. According to other documents included in this collection of papers is a lease of Coomete from John Kershaw to Augustus Bostock. This letter relates to an adjustment to the rent and some discussion over the terms of the lease and the control of rabbits. This is one of a number of documents which relate to the Bostock family who were one of the most important pioneering families of the Western District. They owned and leased various properties around Warrnambool and were involved in many aspects of social and business life. This letter hi-lights the importance of the rabbit problem as early as 1895 to the extent that it was traded against a sizeable deduction in rent.Cream unlined paper, handwritten in black ink. Watermarked down left side. Writing is quite difficult to read.Signed John Kershaw. Dated 24th June* ’95.Addressed to Augustus Bostock.warrnambool, augustus bostock, john kershaw, coomete, 1895,

One of the most common centre draft kerosene lamps one can find in the USA and Canada is the Rayo. Large and sturdy, simple to use, but also notorious for being a fuel hog. This lamp was made by Bradley and Hubbard Metalworks in Chicago also Bradley and Hubbard made the “Perfection” brand lamps that look like the Rayo and are pretty much the same lamp with all parts interchangeable. The Rayo was given away to customers for free as a promotional item by the Standard Oil Company. The lamp’s huge appetite for fuel meant a hefty increase in sales of kerosene for the company and increased profits. The Rayo is a classic centre draft lamp that uses a widely available tubular wick that measures 62mm flat. It employs a simple and reliable mechanism for securing wicks in the burner along with a brass tube with many small teeth at its end. The tube is attached to the toothed rack that’s moved up and down by the adjuster knob.This type of lamp was used in most households and on rural properties before the introduction of electricity and is an early example of a promotional. The lamp was given away to customers of Kerosene oil as a means of increasing the Standard Oil Company sales of Kerosene during the late19th to early 20th century.Lamp of metal without shade. Mantle burner, plated light metal base. Ornate shade holder. Broken glass.Marked "Rayo Junior"flagstaff hill, warrnambool, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, mantle lamp, metal lamp, lighting, oil lamp, bradley & hubbard

One of the most common centre draft kerosene lamps one can find in the USA and Canada is the Rayo. Large and sturdy, simple to use, but also notorious for being a fuel hog. This lamp was made by Bradley and Hubbard Metalworks in Chicago also Bradley and Hubbard made the “Perfection” brand lamps that look like the Rayo and are pretty much the same lamp with all parts interchangeable. The Rayo was given away to customers for free as a promotional item by the Standard Oil Company. The lamp’s huge appetite for fuel meant a hefty increase in sales of kerosene for the company and increased profits. The Rayo is a classic centre draft lamp that uses a widely available tubular wick that measures 62mm flat. It employs a simple and reliable mechanism for securing wicks in the burner along with a brass tube with many small teeth at its end. The tube is attached to the toothed rack that’s moved up and down by the adjuster knob. This type of lamp was used in most households and on rural properties before the introduction of electricity and is an early example of a promotional. The lamp was given away to customers of Kerosene oil as a means of increasing the Standard Oil Company sales of Kerosene during the late19th to early 20th century.Kerosene Lamp, side lifting arm to light.Inscribed "Rayo" and "Made in the USA"flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill-maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, kerosene lamp, lighting, hurricane lamp, storm lamp, rayo ltd

One of the most common centre draft kerosene lamps one can find in the USA and Canada is the Rayo. Large and sturdy, simple to use, but also notorious for being a fuel hog. This lamp was made by Bradley and Hubbard Metalworks in Chicago also Bradley and Hubbard made the “Perfection” brand lamps that look like the Rayo and are pretty much the same lamp with all parts interchangeable. The Rayo was given away to customers for free as a promotional item by the Standard Oil Company. The lamp’s huge appetite for fuel meant a hefty increase in sales of kerosene for the company and increased profits. The Rayo is a classic centre draft lamp that uses a widely available tubular wick that measures 62mm flat. It employs a simple and reliable mechanism for securing wicks in the burner along with a brass tube with many small teeth at its end. The tube is attached to the toothed rack that’s moved up and down by the adjuster knob. This type of lamp was used in most households and on rural properties before the introduction of electricity and is an early example of a promotional. The lamp was given away to customers of Kerosene oil as a means of increasing the Standard Oil Company sales of Kerosene during the late19th to early 20th century.Kerosene Lamp, side lifting arm to light.Inscribed "Rayo" and "Made in the USA"flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill-maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, kerosene lamp, lighting, hurricane lamp, storm lamp, rayo ltd

A number of Plumbing tools dating from 1880s-1970s and used in teaching at Collingwood Technical School then also at Preston Technical School and at Northern Metropolitan College of TAFE's Heidelberg campus. Includes: Kerosene blow torch X 2 (1930s-); Stillson Grips; Pipe Cutter; Mash hammer; Adjustable spanner X 3 different sizes; Caulking tool; 5 way tee, 2X3 way tee, 4 way tee (1930s-); Old Handmade lead traps (student work) X 2; Metal tool tray holding; Offset adjustable spud spanner; Pear shaped lead working mallet; Bossing tool for lead work (1880s-1920s); Soldering iron (1920s-); Set square; Large screwdriver; Also Plumbing texts: • Problems for elementary physics, new rev. edn., by Thomas Tasker and Alexander Boden, Science Press, Sydney, 1966. • Gasfitting. Printed and published by McCarron Bird Pty. Ltd. [Melbourne] • Trade science for plumbing apprentices, Education Dept. Victoria, 1954 • Sanitary Plumbing and water supply, Dept. of Labour • Gasfitting, produced by members of the Colonial Gas Association Limited, Gas and Fuel Corporation of Victoria, and the Technical Division of the Education Department of Victoria. Rev metric edn. 1976 • Mechanical world year book 1953, Manchester Emmott & Co., 1953 collingwood technical school, preston technical school, northern metropolitan college of tafe, plumbing tools, plumbing texts, nmit

The Optacon OPtical-to-TActile-CONverter is a compact, portable reading aid for the blind. It is about the size of a textbook, and weighs less than 2kg. It works by converting a printed image into a tactile image that a blind person can feel with one finger. After a period of training and practice, a blind person can use the Optacon to read ordinary books, magazines, newspapers, and other printed materials. The Optacon was developed after intensive research at Standford University, California, USA and was trialed by clients of the Royal Victorian Institute for the Blind (now part of Vision Australia) in 1973. It has three main sections: 1 a miniature camera, 2 an electronics section, and 3 a tactile stimulator array. The miniature camera, about the size of a pocket knife, is mounted in a housing that has rollers for easy movement along a line of print. The camera is connected to the electronics section by a lightweight cable. The electronics section and the tactile stimulator array are in the main chassis. The array consists of 144 tiny metal rods arranged in six vertical columns and 24 horizontal rows. Each of the rods can vibrate independently. The tips of these rods protrude through holes in a concave finger plate where the index finger is placed flat in order to read. These three components act together to convert the image of a printed letter or other shape into a pattern of vibrating rods, a tactile image of the letter or shape. The letter shape is tactually perceived as an image that moves from right to left on the finger, showing the left or leading edge of the letter first. Letters are felt sequentially rather than all at once, and the image should be kept moving. The Optacon converts a printed O into a tactile form that resembles a crater with a vibrating rim -- a completed circle. C would have a gap or opening on the right side of the curve. The letter F would be felt, sequentially, as a vertical line with two trailing horizontal lines. Because it can convert any ordinary printed image into a corresponding tactile image, the Optacon is not restricted to any special typestyle or language. The camera has a zoom lens that compensates for differences in the size of type. The standard Optacon lens can accommodate type sizes from 6 point to 20 point. With the optional F4A magnifier lens, type sizes as small as 4 point can be read. Powered by a rechargeable battery, and comes with its own battery charger. The battery is contained within the main chassis, and is not removable by the user. There are four basic controls on the Optacon: the Magnification Adjustment zoom button located on the camera section on the side opposite the rollers; and the On-Off switch, the Stimulator Intensity Adjustment knob, and the Threshold Adjustment knob located on the right side of the front panel. The Circuit Breaker protrudes from the right-hand wall inside the chassis compartment. From left to right when the back panel is facing you, are located: the jack for connecting the battery charger; the Battery Check button; the Normal-Invert switch; and the Input/Output I/O connector for use with the Visual Display, when using the Repeater Cable to connect two Optacons to one another or with other accessories. Designed not be removed from the leather case during normal operation, the On-Off switch is a slide switch located on the right side of the front panel. It slides up and snaps into place in the on position. 1 black with orange front, rectangular device in leather case assistive devices, audio equipment

This field First Aid kit is a mixture of items, some prepared for use in wartime, including World War One and some for use in peace time emergencies. The calico bag, produced by the Red Cross in Kalgoorlie, W.A., has been used by the State Emergency Service and at a later date by a scout group. The name, ‘S. Dempster’ is on the striped calico bag. Samuel Dempster was born in Ireland and was living at Panmure when he enlisted. He was attached to the 6 Ambulance training. He served from 1942-46 This is a calico shoulder bag with the shoulder strap adjustable with the use of metal clips. The bag is frayed and rusted and contains 14 items:-eight flat bandages, five safety pins, six small rolled gauze bandages, three navy blue packages of white absorbent gauze, one rolled package bandage,, rubber hose (broken), two small and one large field dressings, two shell dressings, Armed Forces shell dressing (Commonwealth of Australia), dark blue absorbent lint (yellow label), absorbent cotton wool (navy blue wrapper with red label), striped canvas bag, bottle of aqueous solution Acriflavine, two rolled bandages. ‘S.Dempster VX74418’ ‘Red Cross Society Kalgoorlie West Australia’ s. dempster, world war 2, samuel dempster, first aid kit wwii, warrnambool

Part of the Reverend Chaplain Major Thomas Bruce Williams, No 556101, Collection.Khaki battle dress trousers in wool fabric with pleated front. Waistband and pockets lined with light khaki cotton drill fabric. Wide waistband secured with three brown bakelite buttons Inside the waistband are six brown bakelite buttons used to secure braces. On each outer side of the waistband are two tabs with metal fasteners used to adjust the waistband. Extra buttons are sewn onto the outside of the waistband. A zipper fly is on the front of the trousers. Pockets consist of two hip with button down flaps, two lined side and one left leg cargo with button down flap. A light khaki heel protector is sewn into the hem of each trouser leg.On white calico manufacturer's label - handwritten in black ink: '556101, PADRE Tom'.uniform, army chaplain, battle dress, major thomas b. williams

The post World War II migration of European "snow skiiers" into Australia combined with the construction of Hydo Electricity Schemes in both the N.S.W.and Victorian Alps regions, opened up these winter snow areas to a greater influx of tourists and holiday adventurers interested in "winter" sports. The ability to project, on a global scale, skiing facilities of international standards to those in the northern hemisphere during their summer has opened up the Australia ski resorts and their facilities to a much greater winter sport orientated population. These cross country skis were purchased by a member of the Bogong Ski Club and were part of a bulk ski stock consignment from Finland in 1966/67. They were introduced into the Victorian Alps to encourage skiers to take up cross country skiing both at Falls Creek and Mount Buller. This initiative spurred on the now annual 42 kilometre cross country "Kangaroo Hoppet" race at Falls Creek. This race is currently the biggest cross country snow skiing race in Australia. These snow skis were made in Finland. They are wooden (hickory) skis and made from four strips (glued and shaped) pieces of wood that are not laminated. There is a painted blue flash on the top of the skis that extends the full length of the skis. The face of the underside of the skis is flat and is coated in black Stockholm tar. Glider or grip wax was applied onto this base. The top body of the skis is tapered from shoe position to both front and back tips.Tapered curvatures from foot radiating to all sides provides the required aerodynamics. Metal boot bindings consisting of a toe plate with adjustable toe clip and a heel plate, both of which are screwed onto the skis. "KILPA, KARHU URHEILUTARPEITA SPORTART1KLAR, Karhu-Valtz Finland. Hickorypohjin"snow skiing, cross country skiing, falls creek winter tourism

This little steam boiler has been beautifully built. It could have been used to drive an engine in a small workshop, a boat or launch, or even farming equipment. It is an example of the steam technology and mechanisation of the 19th century. William Cook introduced steam heating in England in the 18th century. Steam combined with pressure was used for powering transport, such as steam engines for trains, and manufacturing, such as steam engines driving manufacturing machines. Steam boilers are still used today as an energy-efficient means of power.This steam boiler would have been suitable to drive a small engine, possibly that of a small boat. Coal was added to the firebox for fuel to heat water in the boiler. It is an example of the power used to drive machinery and equipment in the mid-to-late 19th century. Steam boilers like this one have played a part in the evolution of steam power. Steam engine boiler; vertical cylindrical coal-fired boiler with a black firebox at its base and a dome top. The cylinder's sides and top have brass fittings, inlet and outlet taps. A round opening near the base is covered by an adjustable metal plate that controls the boiler's temperature. The front door of the firebox has two hinges at the base and when the side clips are opened. A shiny brass collar tops the tall chimney. Oak wood planks around the sides of the boiler, and held in place by brass bands with nut and screw fixtures. The boiler stands on a metal and wood frame with a looped handle at the back. An inscription has been noted. Circa 1880. "1948 D/430" flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, boiler, steam engine, steam boiler, coal fired boiler, vertical boiler, boat boiler, power source, steam driven, engine boiler, steam machine, firebox, steam engine boiler

In one place in records Pat Faggetter is credited with the donation of this item. It would appear that Pat picked it up from Mrs Coldrey so I have credited Mrs Coldrey as the donor. See also page 10 of green folder. (Ted Arrowsmith)OTICISCOPE An early slide projector. Large, black square unit with chrome parts. Bellows to assist in focus can be slid up to 26cm. On the end of the bellows is screwed a further adjustable lens (8.5cm diam by 11cm long). The body of the unit can be tilted to focus on the screen. This lens is endorsed '8 inch (26cm) high focus Aldus UNO Projector Lens'.This lens and a lamp is stored inside the projector. The projection lamp is an Osram (balloon shaped) patent registered 260 volt Gas Filled 500 watt 51. Made in England. Screw fitting .Power supply is by early English type two pin plug with a toggle switch on left side.Ensign Optiscope No. 6 - Made in Britain - Ensign Ltd - London.photography, projectors

Belt issued to Japanese Naval Officers up until the end of WW2Black leather belt with a two piece brass buckle. The centre of the buckle has an embossed anchor and lotus flower and the two parts of the buckle appear to have been gilded. It comes with a black leather sword hanger which has brass clips at each end. One end is missing the brass securing rivet whilst the rivet at the other end has a hook attached to it. Attached to this hook is a brass S shaped snake with a brass ring around the body. The inside of the belt has four eyelets and a hook on each end to allow for adjustment. It's missing one sword hanger, a belt loop on the LH side and two loops on the inside that the hangers attach to.world war 2, japanese navy

Set of four colour prints, possibly from a Geoff Grant negative of the commissioning of the Bourke St lines, 19/6/1955. Printed on Fujicolor paper. .1 - W6 988 and bus (554?) and tower wagon - Queens Parade Clifton Hill. .2 - W6 988 and two tower wagons at the Russell St. crossover. The two wagons' crews are adjusting the overhead. Buildings on the south side of Bourke St. See also Reg Item 1600 for the black and white photograph. .3 - W6 988 at the intersection of Nicholson and Victoria Parade. .4 - testing a crossover in either Smith St. Fitzroy or High St. Preston - running bang road.mmtb, melbourne, bourke st, testing overhead, commissioning, tram 988

Clock components - comprising two springs and part of the pendulum of the Bundy Clock in the Training Room during the refurbishment of the clock by Graeme Coates during 2019. Returned to the depot 4/9/2019. Found that the springs were too strong for the mechanism - they have been secured with plastic cable ties - do not undo they could cause serious injury. The pendulum was too long - shortened by 72mm, consists of an oval shaped piece of wood and sealed. Notes from Graeme: 1 - wind both springs at the same time 2 - always wind the hands forward to adjust the time 3 - the timing mechanism can be set by hand, the time is on the opposite side to that shown on the case.trams, tramways, bundy clock

Light tan canvas rectangular bag containing two First Field Dressing Satchels The bag has a tongue on bottom to seal the bag.. Satchels are made out of white light canvas and unopened. Each satchel has safety pin wrapped in waterproof paper attached to top of it.Container Bag-: First Field Dressing To Open Outer Canvas Break thread holding flap Inner Waterproof Cover Tear apart at the uncemented corner (indicated by arrow) Contents Two dressings in Waterproof Covers each consisting of gauze pad stitched to a bandage and a safety pin. Directions For Use-;Take the folded ends of the bandage in each hand and keeping the bandage taut apply the gauze pad to the wound and fix the bandage. One dressing to be used for each wound. In the case of head wounds when respirators have to be worn care should be taken to adjust the pad so that it does not interfere with the fit of the facepiece. DO NOT HANDLE THE GAUZE OR WOUND. Johnson & Johnson Pty Ltd Sydney February 1944 (Waterproof containers inscriptions) FIRST FIELD DRESSINGS Tear apart the uncemented corner as indicated by the arrow and remove the paper. Take the folded ends of the bandage in each hand, and, keeping the bandage taut, apply the gauze pad to the wound and fix the bandage. In the case of head wounds when respirators have to be worn, care should be taken to adjust the pad so that it does not interfere with the fit of the face piece. DO NOT HANDLE THE GAUZE OR WOUND Johnson & Johnson Pty Ltd Sydney February 1944

This linesman belt was used under the 1947 Electricity Regulations and before tighter Occupation and Health regulations (late 1990's early 2000's) were introduced that mechanical lifting platforms(wherever possible) replaced the belt up the pole method.The safety concern was that it required that tools needed by the linesman had to be placed in a large canvas bag and attached to the belt (extra weight) then the linesman had to climb the ladder. Ladders had to be at the correct angle and not able to "slip" from their initial footings. A full harness and a secondary fall belt is now mandatory for pole linesmen. The safety of fellow workers could be compromised if they were required to assist or recover the first linesman if needed. In 2006 an additional 269 registered lineworkers were employed. Please note that the terminology of linesman has become unisex. The linesman's belt enabled the linesman to place his feet against the pole adjust the belt (if needed) and lean back securely allowing both hands to be free to work with. This linesman belt is very significant to the Kiewa Valley due to the numerous poles and high voltage overhead power structures that needed maintenance for the extensive "mushroom" installation of electrical power polls(wood and metal). On high poles (steel) climbing pegs were welded on, however in the Alpine areas snow in winter caused an OH&S problem which were hard to overcome. The safety of a linesman when maintenance of electricity line on poles can be highlighted by the New Zealand linesman who survived an 11,000 volt shock when carrying out maintenance. For the record 11,000 volts is four times more powerful than execution by "the electric chair". The maintenance of the linesman's belt was his responsibility (keeping it clean and in "good" condition). Labour laws change this initial responsibility, from the linesman, to the employer. Climbing pegs were installed on higher poles that extended beyond the reach of ladders.This thick leather linesman belt is made from two lengths of heavy lengths of leather straps sewn together to make up 80% of the belt. The remaining 20% is "the belt tonge" which has eleven holes for three (solid steel tang) buckle connections.kiewa hydro electricity scheme, victorian state electricity commission, relays, generators, electrical pole maintenance

A press release from Melbourne Legacy in 1975 which relates a story of how Legacy works. The information was intended to be used by press and magazines etc. The title 'Ambition achieved with a little help from her friends', and is about an 18 year old whose parents died within 12 months of each other. She was doing Matriculation (similar to VCE), and faced a problem with continuing her education until Legacy heard of her situation. Legacy provided free dental care, granted her an allowance, paid her matriculation exam fees. After she matriculated her career path was a Diploma course in Foods and Food Services and Legacy paid for her first year course fees and continued her allowance. Based on her remarkable results Legacy continued supporting her course fees until she graduated a happy, well-adjusted, successful girl in a well known test kitchen. It illustrates Legacy's ability to help ambitious young legatees to succeed and achieve their ambitions.A record of how Legacy promoted their work in the 1970s.Yellow foolscap page x 2 with black type of a press release in 1975.Title 'Ambition achieved with a little help from her friends'press release, case studies

A Plane Table consists of a smooth wooden table surface (with metal strengthening supports) mounted on a sturdy base. The base, a three-legged Tripod, is designed to support the table over a specific point on land. The connection between the tabletop and the adjustable Tripod legs permits the user to level the table precisely, using bubble levels in a horizontal plane regardless of the roughness of the terrain. The Plane Table is a surveying device used in surveying and mapping to provide a level surface on which to make drawings, charts or maps. An alidade, with or without a telescope located on the tabletop is used to sight features and draw angles to that feature. Using these lines to the same feature from different setup locations it is possible to locate that feature on the map. Plane Tabeling was widely used by the early members of the Australian Survey Corps and in both World Wars. It remains a simple and effective tool to teach the fundamentals of mapping and surveying. It was simple to use and was reasonably robust and portable. See also item 6489.2 for the Plane Table Alidade.A wooden Plane Table with alloy fittings to strengthen and support the table top. The table is fixed to a three-legged wooden Tripod with cast alloy fittings and metal pointed tips.royal australian survey corps, rasvy, fortuna, army survey regiment, army svy regt, asr, 4 fd svy sqn, school of military survey

This mobility aid was housed under the old stage area of the Soldiers Memorial Institute building in Pall Mall Bendigo. When the renovations to the building began in late 2016 the Aid was removed and restored by the Bendigo District RSL Men in Sheds program and is now on display in the same building now called Bendigo Military Museum. The Soldiers Memorial was the HQ of the Bendigo RSL Sub Branch. It is not known the origin of the Aid but it was most likely used by disabled Bendigo RSL members post WW1.Three wheeled Mobility Aid. Front wheel is 41cm dia pneumatic, 32mm wide, rear wheel 68cm dia, width 52mm wide. The right wheel axle has a sprocket & chain assembly, the left is free wheeling, both have mud guards. Frame is tubular steel painted reddish colour, the seat and back rest are brown leather, seat sides are timber, there are two timber platforms in front, the top one is adjustable the bottom one is fixed. The chair is steered via a long metal handle fixed to the wheel frame. The right hand side has the sprocket and chain assembly and motion is controlled by turning the handle in a circular motion, only one speed.on the front wheel stem is a transfer. “Webster Brothers Cycle Manufacturers Mitchell Street Bendigo”mobility, aid, wheel chair, brsl, smirsl

Royal Australian Corps of Transport mess dress belonging to Kevin John Herdman. Part of the Kevin John Herdman No. 397661 Collection, See Catalogue No. 5942P for details of his service record..1) Black jacket with two button-down breast pockets and two side pockets with flaps. Jacket buttons at the neck and down the front. Unit insignia on right collar. White starched false collar attached with studs. All buttons bear a unit insignia and are gold coloured. Major's rank insignia on each epaulette. Manufacturer's label on inside left. .2) Pair of black trousers with two white stripes down the outside of each leg. Buttons on waist band for attaching braces. .3) White elastic adjustable braces. .4) Black peaked cap with red band. Gold coloured braiding on peak. Brown coloured sweat band and clear plastic lining..1) On manufacture's label: 'DAVID KLEIN PTY LTD, PTY LTD, VICTORIA, 1966, (upwards arrow)'. On false collar: 'C.G.C.F., SIZE 15'. .2) On manufacturer's label: 'DAVID KLEIN PTY LTD, PTY LTD, VICTORIA, 1966, (upwards arrow)'. .3) Stamped on leather joiner: 'P-F, 10 73, (upwards arrow), 44'. .4) Inside cap: 'COMMONWEALTH GOVERNMENT CLOTHING FACTORIES, MELBOURNE,6 3/4'.uniform, mess dress, royal australian corps of transport, kevin john herdman

This fire helmet may have been one used in England or one used in the late 19th century and early 20th century in Australia. It was made by Firmin & Sons of England, a firm which was founded in 1655. It supplies military ceremonial buttons, badges and uniforms and brass and pith helmets of various kinds. It is regarded as the oldest manufacturing business operating in England today. The Warrnambool Fire Brigade was established in the early 1860s and today has both paid and volunteer firefighters.This helmet has no known local provenance but is retained for display purposes.This is a brass helmet with an oval crown with an ornate scrolled curved piece coming over the crown. There is a decoration of a winged dragon breathing fire and on the front side a torch, an axe and a hose with decorative surrounds. There is a breathing hole at the top of the crown in a petal shape. On the sides are metal medallions holding a chin strap which is adjustable. The edge of the crown has a scrolled band. The front peak is angled with a folded metal edge and the rear peak is a concave shape with a brass screw in the middle. Inside the helmet are 8 screws holding the upper decorative arching piece and a black leather band with eyelets tied together to fir the individual head. There is an oval plaque with wording contained within a decorative belt.Firmin & Sons Ltd 108 & 109 St Martins Lane W.C. Late of 153 & 154 Strandwarrnambool fire brigade, history of warrnambool

Fob (or pocket) watches were developed in Europe in the 16th century and gained wide usage during the mid 18th century until World War 1 when the wristwatch was invented. These watches were designed to be carried in a small pocket and attached through the means of a 'fob' which could be a chain or made from a variety of materials such as leather. Their popularity peaked in the nineteenth century where they were an important part of middle and lower class society as well. The inclusion of the word RAILWAY on the face of the watch suggests a possible use by an employee of the railways. This item is of social significance as fob / pocket watches were valued as an essential object in all levels of society. For some occupations, such as the railroads, it was a necessary tool of the job. Steel Railway Lever open face pocket / fob watch dated 1920s-1930s. The white dial has large black arabic numerals and outer minute divisions around the edge. A circular insert and small hand to show the seconds is at the bottom of the watch face. The hour hand is a rounded leaf shape, and the minute hand a thin diamond shape. Both hands and the small rounded end of the second hand reflect a metallic blue sheen in the right lighting. The words RAILWAY LEVER, 15 JL and SWISS MADE are on the dial. The lever set on watches was a requirement for railroad watches. It required a two step process for the hands to be adjusted. 15 JL refers to the movement being a 15 jewel one.The front dial of the watch has the words 15 JL, RAILWAY LEVER, and SWISS MADE. flagstaff hill maritime museum and village, warrnambool, great ocean road, shipwreck coast, fob watch, pocket watch, watch, horology, time keeper, swiss made, railway lever, 15 jl, 15 jewel

HISTORY OF THE LOCH ARD: - The Loch Ard got its name from ”Loch Ard” a loch that lies to the west of Aberfoyle, and to the east of Loch Lomond. It means "high lake" in Scottish Gaelic. The vessel belonged to the famous Loch Line which sailed many vessels from England to Australia. The Loch Ard was built in Glasgow by Barclay, Curdle and Co. in 1873, the vessel was a three-masted square-rigged iron sailing ship that measured 79.87 meters in length, 11.58 m in width, and 7 m in depth with a gross tonnage of 1693 tons with a mainmast that measured a massive 45.7 m in height. Loch Ard made three trips to Australia and one trip to Calcutta before its fateful voyage. Loch Ard left England on March 2, 1878, under the command of 29-year-old Captain Gibbs, who was newly married. The ship was bound for Melbourne with a crew of 37, plus 17 passengers. The general cargo reflected the affluence of Melbourne at the time. Onboard were straw hats, umbrellas, perfumes, clay pipes, pianos, clocks, confectionery, linen and candles, as well as a heavier load of railway irons, cement, lead and copper. There were other items included that were intended for display in the Melbourne International Exhibition of 1880. The voyage to Port Phillip was long but uneventful. Then at 3 am on June 1, 1878, Captain Gibbs was expecting to see land. But the Loch Ard was running into a fog which greatly reduced visibility. Captain Gibbs was becoming anxious as there was no sign of land or the Cape Otway lighthouse. At 4 am the fog lifted and a lookout aloft announced that he could see breakers. The sheer cliffs of Victoria's west coast came into view, and Captain Gibbs realised that the ship was much closer to them than expected. He ordered as much sail to be set as time would permit and then attempted to steer the vessel out to sea. On coming head-on into the wind, the ship lost momentum, the sails fell limp and Loch Ard's bow swung back towards land. Gibbs then ordered the anchors to be released in an attempt to hold their position. The anchors sank some 50 fathoms - but did not hold. By this time the ship was among the breakers and the tall cliffs of Mutton Bird Island rose behind. Just half a mile from the coast, the ship's bow was suddenly pulled around by the anchor. The captain tried to tack out to sea, but the ship struck a reef at the base of Mutton Bird Island, near Port Campbell. Waves subsequently broke over the ship and the top deck became loosened from the hull. The masts and rigging came crashing down knocking passengers and crew overboard. When a lifeboat was finally launched, it crashed into the side of Loch Ard and capsized. Tom Pearce, who had launched the boat, managed to cling to its overturned hull and shelter beneath it. He drifted out to sea and then on the flood tide came into what is now known as Loch Ard Gorge. He swam to shore, bruised and dazed, and found a cave in which to shelter. Some of the crew stayed below deck to shelter from the falling rigging but drowned when the ship slipped off the reef into deeper water. Eva Carmichael a passenger had raced onto the deck to find out what was happening only to be confronted by towering cliffs looming above the stricken ship. In all the chaos, Captain Gibbs grabbed Eva and said, "If you are saved Eva, let my dear wife know that I died like a sailor". That was the last Eva Carmichael saw of the captain. She was swept off the ship by a huge wave. Eva saw Tom Pearce on a small rocky beach and yelled to attract his attention. He dived in and swam to the exhausted woman and dragged her to shore. He took her to the cave and broke the open case of brandy which had washed up on the beach. He opened a bottle to revive the unconscious woman. A few hours later Tom scaled a cliff in search of help. He followed hoof prints and came by chance upon two men from nearby Glenample Station three and a half miles away. In a complete state of exhaustion, he told the men of the tragedy. Tom then returned to the gorge while the two men rode back to the station to get help. By the time they reached Loch Ard Gorge, it was cold and dark. The two shipwreck survivors were taken to Glenample Station to recover. Eva stayed at the station for six weeks before returning to Ireland by steamship. In Melbourne, Tom Pearce received a hero's welcome. He was presented with the first gold medal of the Royal Humane Society of Victoria and a £1000 cheque from the Victorian Government. Concerts were performed to honour the young man's bravery and to raise money for those who lost family in the disaster. Of the 54 crew members and passengers on board, only two survived: the apprentice, Tom Pearce and the young woman passenger, Eva Carmichael, who lost her family in the tragedy. Ten days after the Loch Ard tragedy, salvage rights to the wreck were sold at auction for £2,120. Cargo valued at £3,000 was salvaged and placed on the beach, but most washed back into the sea when another storm developed. The wreck of Loch Ard still lies at the base of Mutton Bird Island. Much of the cargo has now been salvaged and some items were washed up into Loch Ard Gorge. Cargo and artefacts have also been illegally salvaged over many years before protective legislation was introduced in March 1982. One of the most unlikely pieces of cargo to have survived the shipwreck was a Minton majolica peacock- one of only nine in the world. The peacock was destined for the Melbourne 1880 International Exhibition. It had been well packed, which gave it adequate protection during the violent storm. Today the Minton peacock can be seen at the Flagstaff Hill Maritime Museum in Warrnambool. From Australia's most dramatic shipwreck, it has now become Australia's most valuable shipwreck artifact and is one of very few 'objects' on the Victorian State Heritage Register.The shipwreck of the Loch Ard is of significance for Victoria and is registered on the Victorian Heritage Register ( S 417). Flagstaff Hill has a varied collection of artefacts from Loch Ard and its collection is significant for being one of the largest accumulation of artefacts from this notable Victorian shipwreck. The collections object is to also give us a snapshot into history so we are able to interpret the story of this tragic event. The collection is also archaeologically significant as it represents aspects of Victoria's shipping history that allows us to interpret Victoria's social and historical themes of the time. The collections historically significance is that it is associated unfortunately with the worst and best-known shipwreck in Victoria's history. Heavy duty brass sleeve retrieved from the wreck of the LOCH ARD. It is pinched and broken off at one end, enclosing an extendable inner sleeve, which is connected to a brass bracket fixed at right angles. The circular enclosing bracket would hold (and fix by an adjustable brass screw) a through or cross pipe of similar diameter to the outer sleeve. The artefact is a structural piece delivering vertical support to a horizontal rail (missing) and not for transporting gas. It is constructed of thick gauge metal suitable for weight/load bearing and its sliding sleeve design is similar to a modern shock absorber, or a telescopic leg supporting a surveying instrument. There is concreting sediment immobilising the sleeves and lining the inner surface of the bracket. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, loch line, loch ard, captain gibbs, eva carmichael, tom pearce, glenample station, mutton bird island, loch ard gorge, brass fitting, brass pipe, 1878 shipwreck

In about 1888 William George Ashman (1871-11/2/1944) began a tailoring business in High Street, Eaglehawk. In 1890 he admitted his brother Arthur Thomas Ashman to the business and they traded as Ashman Brothers. In 1936 the company of Ashman and sons was registered at 265 Hargreaves Street. They specialised in made to measure, hand tailored suits. William married Clara Hunkin (1871-25/11/1944) in 1894. Their sons, John, Eric, Basil and Charles followed into the family business.Woolen fabric trousers, part of Dress Suit. A decorative strip runs down each leg. The waistband can be adjusted on either side by belt/buckle attachments. Trousers fasten with two buttons and there are four buttons at the fly opening at front. There are two deep lined pockets either side and one top pocket at rear on LHS. There is a maker's label stitched to the lining of the Rear pocket which reads "Ashmans, Hargreaves Street, Bendigo 'The Home of Better Suits'". A name written in ink below the maker's label is 'Mr M. Suurpaa, 28-3-1961 7252." Leather strips have been sewn inside edge of each leg cuff for garment protection.men's clothing, formal wear, trousers