Photograph shows metal sprung axle box as fitted to standard four wheel cable trailers built at Nicholson Street Workshops between 1885 and 1923.Yields information about cable tram componentsBlack and white photograph with note on rearIn ink "25" and "K McC"cable trams, trailer trucks, axle boxes, four wheel, nicholson street workshops

Photograph of an Melbourne Tramway and Omnibus cable tram showing the axle box, springs and wheel supporting the body of a trailer. Shows the side skirts around the wheel. Part of the brake rigging can be seen as well.Yields information about cable tram trailers wheel sets.Black and white photograph on paper. Two copies held.trams, tramways, mtoco, cable trams, trailers, wheels, axle boxes

Set of three drawings related to the Brill 22E Maximum Traction trucks: 1 - "Brake Rigging Brill Maximum Traction Truct No. 22E" - showing the dimensions of the levers and pivot points. For the relevant Geelong drawing T1647 see item 8044 and 9025. 2 - "Standard Pony Axle" - traced from MMTB drawing R3755 3 - "Pony Axle Box" - traced from MMTB drawing R1112 and dated in ink 28-4-1955Yields information about Brill 22E brake rigging and equipment.Set of three Drawings - dyeline print on plain paper with a brass clip in the top right hand corner.tramcars, brill 22e, pony axles, axles, axle boxes, brake rigging, ballarat, geelong, drawings

Axle box cover from a Tasmanian Main Line Railway rail vehicle from 1874 The Tasmanian Main Line Railway Company (T.M.R.L.) was a privately owned railway company that existed in Tasmania from 1872 to 1890. The company were the first operators of rail services between Hobart and Launceston, where it connected with the Launceston and Western Railway (L.W.R.) It started construction of a 3' 6" gauge line between Hobart and Launceston in 1873 which was completed in December 1875. and was officially opened on 1 November 1876. The route of the railway was selected largely as a result of vocal local interests and accordingly traversed some reasonably unfavorable topography, particularly in the southern section. Because the TMLR had limited finances, the line was built to the narrow (1067 mm) gauge and included long sections of steep gradients and sharp curves. The final eighteen kilometres of the route from Western Junction to Launceston used the existing broad gauge alignment of the Launceston and Western Railway, with a third rail being laid for use by the narrow gauge trains A close but uncomfortable relationship with the Government was resolved in 1890 with the purchase of the company's assets by the Crown and their incorporation into the Tasmanian Government Railways on 1 October 1890. Historic early Tasmanian Main Line Railway - Vehicle Axel Box cover Axle box cover from a Tasmanian Main Line rail vehicle from 1874.T.M.L.R - 1874 -axle, tasmanian main line railway, axle box, tasmania, main line,

Memento or Pen and Ink stand featuring a model of the Peckham Pendulum axle box. Made from wood and brass with space for pens and ink bottles, titled "The Peckham truck and Engineering Company Ltd London". Features a model of the Peckham axle box with rotated within the frame. See https://www.tramwayinfo.com/Tramframe.htm?https://www.tramwayinfo.com/Models/Howto/Trucks.htm accessed 7/7/2020 for some details.trams, tramways, trucks, peckham, models, souvenirs

Photograph shows cast iron axle box and horn ways with rubber "springs" as used on John Stephenson New York built cable trailers which became Melbourne numbers 1 to 20.Yields information about cable tram componentsBlack and white photograph with note on rearIn ink "24" and "K McC"cable trams, trailer trucks, john stephenson, cast iron, rubber springs, melbounre number 1

"J547 undergoes maintenance that required removal of its motion gear, axle box and wheel set. The dome cover has also been removed to facilitate a boiler inspection and/or work on the regularor valve. November 1962" - NewsrailDigital TIFF file Scan of 35mm Ilford FP3 black and white negative transparencybendigo, bendigo railway station, george coop collection, j-512, j-547, j-class steam locomotive (vulcan foundry), railway turntable, railway workshop

The drawing provides details of the two sets of springs that fit on either side of the axle box of a Brill 21E four-wheel truck. Gives load, sizes, and material dimensions. Revision E dated 7-11-1958. Prepared by the MTTB for use on four-wheel trams. Original drawing dated 30/9/1927Yields information about Brill 21E truck axle box springs.Drawing Foolscap size with two punched holes on the left hand side.tramcars, 21e trucks, brill 21e, springs, mmtb

Instruction - 5 pages - duplicated foolscap sheets - headed "MMTB Engineering Department - Workshops and Running Shed Branch" - titled "Pitman Duties" Details duties of Pitmen at depots, in adjusting brakes, oiling bearings, training, responsibilities, inspections, packing of bearings, inspections, hot axle boxes, changing of trucks and general maintenance. Dated May 1970.trams, tramways, depot, safety, workshops, pitmen, instructions, procedures, brake rigging

Set of five colour prints of tram W5 725 derailed in High St Kew during track reconstruction work at the corner of Derby St Kew. Tram was bound for North Balwyn when it derailed on a section of track that had been dismantled, possibly when it hit or dislodged a track crossover. Tram has advertisements for Bonds, Tollana Wines, Park Drive cigarettes, .1 - tram derailed at the top of the hill down to Kew Cemetery. .2 - with workmen setting up the tram and place on the temporary transport wheels. The second axle box towards the drop centre is on an angle compared to the nearest axle box. .3 - close up view of the damaged truck. .4 - General view of the scene looking back towards Kew Junction. .5 - view of the damaged crossover section. Date: during the 1970's.trams, tramways, accidents, derailments, kew, high st, north balwyn, route 48, temporary track, tram 725

Yields information about the Ballarat overhead, track layouts, terminals and the Sebastopol type cars.Three hand written foolscap pages with notes on the Ballarat Tramways overhead, the Sebastopol tramcars axle boxes, double ended sidings at Victoria St and Lydiard St North, possible track extensions, Viewpoint terminus, Forest City signs, View Point Loop and Bridge St relaying in 1957. Contained within Reg Item 5507 - Foolscap binder with green covers, black binding edge and metal clips. overhead, terminus, view point, signals, sebastopol type

Photograph of SW6 850, at South Melbourne depot, side on view. Made by Sutcliffe of 94 Elizabeth St Melbourne for the MMTB. See also Reg Items 674 and 3426 for other photos, probably taken at the same time.Yields information about SW6 850 when new in 1939.Photograph, Black and White, two copies held.In ink on the rear: Copy 1 - M&MTB SA 948, SW6 850, South Melbourne Depot 1939" Copy 2 - M&MTB SW6 850, Note: Roller bearing in lieu of axle boxes brasses, tail lights . ?Hanna St Depot, March 1939" Has Keith Kings stamp "SA 225".trams, tramways, sw6 class, tram 850

Black and white photograph of the first of SW6 class tramcars, No. 850 at South Melbourne Depot following its construction showing the tail light and the dash canopy lighting. The photograph does not have the sign "This is your car use it" as shown on the other official photograph of this tram - see page 41 of the 5th Edition of Destination City. Tram shows route 77 with the destination of Special. Photograph by Sutcliffe Pty Ltd, Illustrative Photographers of 94 Elizabeth St Melbourne. .1 - as above - from the Keith Kings collection - added 4/4/2019. .2 - as above but with the sign "This is your car use it" - added 4/4/2019. See Reg Item 3558 for another print within an album.Stamped on rear in red, with the photo number in black "Sutcliffe Pty Ltd, / Illustrative Photographers / No. 3 / 94 Elizabeth St Melbourne / CENT 1500 - 2601" (Their Melbourne central exchange phone number) .1 - Has the photographers stamp, along with Keith's details in ink on the rear "M&MTB S-A947 / SW6 - 850 / South Melbourne Depot 1939 / Note: Tail-lights & Dash Canopy Lighting, Roller Bearing Axle Boxes". Date stamp 12 Jan. 1948. .2 - Has the photographers stamp, along with Keith's details in ink on the rear "M&MTB S-A946 / SW6 - 850 / South Melbourne Depot 1939 / Note: Tail-lights & Dash Canopy Lighting, Dash Advert, Roller Bearing Axle Boxes". Date stamp 12 Jan. 1948.trams, tramways, mmtb, sw6 class, new trams, south melbourne depot, route 77, tram 850

Sixty page book - gloss paper, plus end papers and heavy card covers, titled "SKF Bearings in Tramway Service". Published by the "The SKF Ball Bearing Company Ltd" in August 1939, gives details of the type of ball bearings available for tramcars - axle boxes, tramway motors, current collection - trolley poles and pantographs. Has drawings, illustrations, photographs etc. Photographs include Hobart 8 and a Wellington Fiduca tram. Address of Melbourne office given as 539 Bourke St, also addresses for Sydney and Brisbane. Printed in Sweden.$20 inside front cover.trams, tramways, tramcars, bearings, skf ball bearings, hobart

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport. This locomotive was built for Sydney suburban passenger duties, originally carrying the number S 1240 of the S 636 class and entered service in 1914. It became the (C)30 class in the 1924 renumbering scheme, with S 1240 renumbered to 3112. Locomotive 3112 was one of the last (C)30 class locomotives in NSWGR service when withdrawn in February 1972. In October 1974 it was purchased by the Lachlan Vintage Village, Forbes which was not financially successful. In 1986 it was forced to auction off its locomotives. 3112 was purchased privately by the late Barry Tulloch and subsequently restored for main line duties at Cowra Depot with the assistance of a group of supporting volunteers. 3112 was very active in the NSW steam scene from 1988 onwards As part of the Australian Bicentennial celebrations 3112 attended the AusSteam '88 event in Melbourne, travelling south in the company of 1210. 3112 was supposed to have left Goulburn, bound for Melbourne early on 14 October 1988, but failed with a hot axle box that prevented it from departing on time. The locomotive was repaired and later that day, ran south to join 1210 at Albury on 15 October, to continue the journey to Melbourne. After this Locomotive 3112 saw extensive rail tour use. 3112 changed hands in 2007 and the new owner arranged storage in Canberra on a private siding adjacent to the Canberra Railway Museum. Although nominally operational, it is not currently in use.On side of locomotive "3112" railways wodonga, fred rochow, locomotive 3112

Catalogue No. 206 of the J. G. Brill Co. of Philadelphia PA, titled "Brill Trucks" on front cover and "City and Interurban Trucks" on page 1. Comprises: Card cover very light grey on outside, grey inside which is a larger size than that of the rest of the book. Has the names of the J. G. Brill associated companies (American Car Company of St. Louis, G. C. Kuhlman Car Co. of Cleveland Ohio, Wason Manufacturing Company of Springfield, Massachusetts and Compagnie J. G. Brill, Paris France) as well. On the inside of the front cover and on the inside back cover are patterns involving the Brill logo. To the printed catalogue is a matching out 4pp again with the same Brill logos. This sheet is the same size as the text pages. Forty page printed text on a heavy gloss manila colour art paper. Front cover gives details of Brill's office addresses, and agents, including the Australasian agent - Noyes Brothers. Page 3 gives an introduction to the quality of Brill trucks and page 39 gives an index to the various trucks and components. Each truck type has a photograph, parts list and dimension details. Trucks covered are: Radiax, 21E, 22, 22E, 27E, 27F, 27G, 27MCB, 39E, 50E. Equipment detailed are the Half-Ball brake hanger, oil retaining center bearing, standard journal (axle) box, solid forged side frames and axle data. Page 38 details the information to be provided when ordering trucks. Image of each sheet added 25/3/2015.On front cover, date stamp of ESCo, Ballarat "1 Apr 1914". The printers signature is shown on page 40.trams, tramways, 21e trucks, 22e trucks, j. c. brill co., bogies, interurban

Yields information about the drawings that were used by the depot or workshop staff as reference drawings. Has a strong association with the depot workshop staff. Yields information about equipment on Ballarat tramcars and Signalling.Folder containing 46 blueprints or Dyeline prints of SEC tram equipment drawings. Front of folder made from a cloth back sheet of paper extended to secure to a thick cardboard runner. Rear of folder made from an old tram advertising panel or cardboard sheet, cut to size and secured to a thick cardboard runner with a cloth backing on both sides. Sheets secured with three brass screwed clips. Front cover damaged in bottom right hand corner. Rear cover breaking apart on outside around cloth binding. Heavy dirt marks from “grease” on bottom half of rear cover. Contains 46 drawings which have been individually catalogued and numbered on the rear of each drawing within the folder. Some of the drawings have been folded. Reg Item Micro Film No. Old BTPS No. SEC Drawing No Title 4807 42/4 1 VB4/8103C Westinghouse T1F Controller Main Cylinder Segments. 4867 47/2 2 BA-T8-8128 Westinghouse 225N Motor Case Bolt 4830 22/3 B 3 BA-T7-7666 Half Ball Brake Hanger Link, Driving Wheel, Brill Maximum Traction Truck 22E 4868 44/3A 4 BA-T8-8113 Split Suspension Bearing for Type W225 Motor (Westinghouse) 4869 52/2 5 BA-T8-8158 Contact Tips for G.E. Compressor Controller 4818 52/3 6 BA-T8-8159 GE B-23 Contact Finger Tips for G.E. Type ‘B’ Main Cylinder 4870 6/1 7A BA-T3-6734 Brass Nut for Switch Mechanism 4829 6/2 7B BA-T3-6735 Tongue Clip Link for Switch Mechanism 4871 6/3 7C BA-T3-6736 Fulcrum for Switch Mechanism 4872 6/4 7D BA-T3-6737 Plunger for Switch Mechanism 4832 7/6 8 BA-T3-6754 Pivot for Switch Mechanism No numbers 9 or 10 4873 17/5 11 BA-T7-7639 Detail of Motor Pinion for Brill Cars 4831.2 21/4 B 12 BA-T7-7661A Half Ball Hanger Links – single bogie trucks 4874 21/6 13A BA-T7-7663 Axle Box Inner Spring Driving Wheels Maximum Traction Truck 22E 4875 22/1 13B BA-T7-7664 Axle Box Outer Spring Driving Wheels Maximum Traction Truck 22E 4876 22/2 14 BA-T7-7665 Body Spring Brill Maximum Traction Truck 22E 4830.2 22/3B 15 BA-T7-7666A Half Ball Brake Hanger Link Driving Wheel Brill Maximum Traction Truck 22E 4877 22/4 16 BA-T7-7667 Body Spring, Brush Maximum Traction Truck 22E 4820.2 22/6 A 17 BA-T7-7669 Wear cups for Half Ball Brake Hanger Links, Single & Double Bogie Trucks 4878 50/5 18 BA-T8-8149 Connections of Line Breaker and Ratchet Switch for use with Drum Controller 4879 74/6 19 BA-T13-8757/9 Signal boxes, Back of Panel Wiring and External Connections 4880 45/1 20 BA-T8-8116 Trolley Harp 4806 15/3 21 BA-T7-7625 Equalizing Lever, Fulcrum, Brill 21 E truck 4881 15/5 22 BA-T7-7626A Brake Beam Fulcrum Brill 21E truck 4808 16/1 23 BA-T7-7628 Pinion Remover, GE 201G and GE 202 motors 4882 16/3 24 BA-T7-7630 Spring Posts, Brill 21E Truck 4883 21/3 25 BA-T7-7660 Brake Shoe Holder, Driving Wheel, Maximum Traction Truck Brill 22E 4884 21/5 26 BA-T7-7662 Brake Rod Guide, Single Bogie Trucks 4885 22/5 27 BA-T7-7668 Brake Shoe Holder, Pony Wheel, Maximum Traction Truck Brill 22E 4809 42/2 B 28 BA-T8-8101 Trolley Wheel and Axle 4815 42/1 B 29 BA-T8-8102A Motor Suspension Bearing, GE 202 Motor 4796.2 42/5 30 BA-T8-8104 Connection Diagram WH 225N Motor 4886 42/6 B 31 BA-T8-8105B Motor Suspension Bearing, GE 201 Motor 4797.2 48/6 32 BA-T8-8137 WH T1F Controllers 4816 49/2 33 BA-T8-8138 Connection Diagram GE 202 Motor 4887 49/3 34 BA-T8-8139 Connection Diagram K-36-J Controller 4888 50/3 35 BA-T8-8146 GE K-36-JR Controllers, with line breaker (Connection diagram) 4889 50/6 36 BA-T8-8150 Commutator for Westinghouse 225N Motor 4846 51/1 37 BA-T8-8151A Armature Bearing Lining, Commutator End, Type GE 201G Motor 4813 51/2 38 BA-T8-8152 Armature Winding Diagram Westinghouse 225 Motor 4840.2 51/40 39 BA-T8-8154A Armature Bearing Lining, Pinion End, Type GE201G Motor 4890 51/6 40 BA-T8-8156 Armature Bearing Lining, Pinion End, Type GE202A Motor 4891 52/1 41 BA-T8-8157A Armature Bearing Lining, Commutator End, Type GE202A Motor 4892 64/5 42A BA-T9-8392A Step Hangers, Single and Double Bogie Trucks, Hinged Type 4785.2 64/6B 42B BA-T9-8392/1A Step Hangers, Single and Maximum Traction Trucks, Fixed Type 4812.2 43/1 43 BA-T8-8106B GE K36J Controller, Main Cylinder Segments 4893 50/2 44 BA-T8-8145A GE B23E Controller, Main Cylinder Segments 4816 65/2 45 BA-T9-8394B Door Lock for Motorman’ Cabin Maximum Traction Trucks. 4810 73/3 46 BA-T13-8757 Ballarat Electric Tramways Signalling System, Arrangements & Details of Box.On front cover of folder, "1 - 46"trams, tramways, drawings, ballarat, sec, depot, workshops

The Q class were introduced as bogie flatwagons in the 1870's. Large Q wagons as shown were built to the 1920's In the early 1900's, some Q wagons were modified for Pintsch Gas traffic with a small pump motor cabin at one end and a tank for carrying the gas. Other conversions for traffic were as required. Examples were: sheet glass, skeletal underframes between workshops In 1926 the railways built two narrow gauge Garratt locomotives. As normal wagons were unsuitable for moving these locomotives a special skeletal wagon was built. The engines were split into units for transportation. It featured axle bearings and boxes from steam engines, had hinged buffers that could drop out of the way during loading/unloading. It also featured 'strap' rail along the deck. The wagon was Q 129. This wagon was also available for general narrow gauge rolling stock. Q wagons were numbered from 1 to 136. Service History: *Q 129.VA - 1/ 6/1926 NWS Built new H/brake & drop buffers. For traffic of Narrow Guage stock 31/ 1/1931 NWS Into Workshops - 16/ 6/1931 NWS Out of Workshops (50 days) 6/11/1931 NWS Into Workshops - 27/11/1931 NWS Out of Workshops (22 days) 24/ 8/1936 NWS Into Workshops - 10/ 9/1936 NWS Out of Workshops (18 days) 27/11/1936 NWS Into Workshops - 26/ 2/1937 NWS Out of Workshops (Light repairs) circa 1960 - Photograph SL20 p32, loaded with 7NA / /1975 - Photograph #393 / /1976 - Photograph #553, #554 19/ 3/1979 - Condemned - 10/ 4/1979 - Off Register - 10/ 4/1979 - Sold (to) ETR, Belgrave / /1989 EME Body [GRE]. [SXC]: 29/3/92, MEL127E5, Puffing Billy at station Historic - Victorian Railways - Transporter wagon used to carry and transfer 2' 6" Narrow gauge rolling stock over Victorian broad gauge (1,600 mm (5 ft 3 in) main lines to the narrow gauge lines. Q 129 was unique, it was built to transport narrow gauge locomotives. Transporter Wagon made of Steel and wrought Iron129Q129q, puffing billy, transporter wagon

The butter stamp rolling pin was used in The Orbost Butter factory.It was rolled across the butter in a wooden box, lined with a wax paper.Bicarbonate of soda was added to the butter to stop it from going rank.The first shipment in about 1893 to England went rank and was only good for axle grease on wagons and carts.The milk was brought to the factory by horse and dray.Most people would take the whey home for their pigs,which were abundant on the farms in the Orbost district. The Orbost Butter and Produce Co. Ltd was registered on June 1st 1893 and was an important source of income to the Orbost district. Large, hand carved, round wooden roller with handle at each end. There is a central carved word, with a pattern of raised squares either side of the carved word and an uncarved area at either end of the roller. The stamp rests on a wooden plinth. "AUSTRALIA" carved in reverse around the width.orbost-butter-factory dairy butter

By the later 1800s the dirt roads in the then out-lying areas of the City of Moorabbin became dangerous, and almost impassable due to huge potholes and muddy swampy areas. The heavily laden market gardener’s carts regularly broke axles and wheels, and horses foundered on their way to the Melbourne markets. Even worse, the heavier “iron maidens”, carrying their malodorous loads of sewage from Melbourne’s inner suburbs for dumping in the outlying areas of the City of Moorabbin, also got bogged in the mire. It was decided that a practical solution to this problem was to install a metal plateway on the side of the problematic roads. In about 1887 the Moorabbin Shire Centre Road, in the Brighton East area, two parallel metal rails were installed so that the wheels of carts could run along smoothly, the horse travelled in the filled, middle area between the rails. Point Nepean Road plateway was removed in 1930 and Centre Dandenong Road plateway was removed in 1934-35. The worn plateway along Centre Road, East Brighton (now known as Bentleigh), was gradually taken up in several pieces, commencing in the the1920s, when its condition deteriorated and it caused a hazard to bikes, pedestrians, motor-cycles and the few early cars. The early steel plateway, constructed by David Munro, and opened on 23rd March 1885 by Thomas Bent, was built along Nepean Highway, between Asling St. and Bay St. The Point Nepean Track was subsequently extended into Moorabbin with branches along Centre, Cumins, South, Wickham, and Keys Roads, the total length was 13 miles. In 1908-1909 plates were laid along Centre Dandenong Road to Ross Street Bentleigh This innovative solution proved successful and was used until gradually the main roads were upgraded, and motorised vehicles started to appear. Two parallel metal rails were installed in the right hand side of a few main roads in the Shire of Moorabbin so that the wheels of heavily-loaded market gardener's carts on their way to markets in Melbourne could run along smoothly. The horse pulling the carts travelled in the filled, middle area between the rails. The Steel Plateway was constructed by David Munro, and opened on 23rd March 1885 by Thomas Bent. The wheelway first only ran along Nepean Highway, but it soon extended from Centre Dandenong Road, along Nepean road to its junction with Chapel Street, St Kilda. Later branch lines were built along Centre Road, Bentleigh as far as Warrigal Road and, according to early photographs, along Wickham Road Moorabbin as well. This innovative solution proved successful and was used until gradually the main roads were upgraded, and motorised vehicles started to appear. There was a problem with the wheelway : there was only a single set of rails and this was established on the right-hand side of the Nepean Road, travelling towards the city. Traffic FROM the city travelled on the correct or left-hand side of the road. The exception to this rule was the malodorous iron-clads, heavily riveted iron carts, generally travelling in convoy, carrying several tons of human effluent out of Melbourne to be trenched-in in the sandy soil of the Moorabbin district. Moorabbin City Council donated and installed a small section of Plateway at Box Cottage Museum in 1984melbourne, brighton, moorabbin, roads, plateway, wheelway, transport, st kilda, bent thomas, munro david, market gardens, steelway, carts horse-drawn, iron maidens, point nepean track

Pamphlet or report printed on A3 gloss paper, folded into A4, with a brown printed cover and a photograph of Z3 117, Melbourne, in Bourke St Melbourne, with the destination of City - Spring Rides and in the route number box "New Tram - Free Rides today". Inside pages and rear cover give details of the trams, its equipment specification, how a chopper control works, car control systems, rotary converter for 24V DC and 220V AC systems, drawings of the trams, and technical data, including a simplified wiring diagram. Produced by AEG - Telefunken of Berlin.trams, tramways, z3 class, aeta, specification, preston workshops, new trams, tram z3 117

A Dray is a type of dead axle wagon that was used to transport heavy loads or objects. They had a flat level floor and while some had no sides, others had box bodies and sides. Tip Drays (also known as Tip Carts, Muck Cart, Scotch Cart, Tumbrel or Putt in different parts of England) were smaller than other drays as their loads were heavy and usually only pulled by one horse. Their basic design included two wheels, a tipping body and shafts. The Tip Dray has a unique mechanism that allows the top to tip backwards to tip the load out of the back of the dray. The tipper was activated by a handle at the front allowing the driver to operate it while still having control over the horse. A Tip Dray was an indispensable piece of equipment in the days before tractors and mechanical trucks. They were used by farmers and carters to transport hay, rocks, bricks, gravel and rubbish etc. and because they were useful for dumping loads, they were favoured for use in road and railway construction. A photo in the collection of the Lorne Historical Society shows a tipping dray being used during the construction of the Great Ocean Road. They were part of the daily street traffic in towns and cities around Australia from the early days of settlement. In Australia in the early 1900's, carters began to join unions to protect their jobs and pay. N.S.W. had a "Trolley, Draymen and Carters Union", Queensland had a "Tip Dray Men's Association" and in W. A. the "Top Dray Driver's Union" had a "cessation of work" in 1911 when they were fighting for an increase in their day's wages. In 1910 a meeting of Tip Carters was held in Geelong at the Trades Hall to discuss the formation of a union (The Geelong Tip Dray Carters) which was a success and a schedule of rates for all carting, whether by contract or day labor, was fixed. By 1912 they had "labelled" more than 50 drays and had representatives on the "Trades Hall and Eight Hours Committee". By the mid 1930's and early 1940's, tip drays were being superseded by mechanical trucks and utes. However tip drays continued to be used in some circumstances. They were a practical solution to the problem of petrol rationing during W. W. 2. It was noted in a letter to the editor in the "Sunshine Advocate" in 1938 that a positive argument for continued use of Tip Drays for rubbish collection related to the idea that a horse drawn vehicle involved with lots of stops and starts at different houses (very like a milkman's delivery route) often involved the horse "driving itself" while the driver picked up the rubbish - something a motor truck was unable to do! Another article written in August 1935 and published in the Age in a parliamentary report into the rubber industry noted "tip drays had almost disappeared and in their place, metal was carted in 5 ton motor trucks" but the report went on to say that as a part of the Government relief work (during the Great Depression) the Government had "to some extent reintroduced the tip drays so that a greater number of men would be employed". This particular tip dray was owned by Mr. Oswald (Jack) Bourke. He used it to deliver dry goods from Sunbury to the Queen Victoria Market in Melbourne several times a week in the 1930's and then (between 1945 and 1962) Mr. Bourke used it on the garbage round in Springvale Victoria for the Springvale Council. The Council owned three drays and the "No. 3" painted on this dray is in recognition of its original number. After the death of Mr. Bourke in 1990, one of Mr. Bourke's sons (Andy) found the dray in a shed and restored it. The sign writing on the back and side panels were added during the restoration. This Tipping Dray is a significant example of a horse drawn vehicle that was used by workers from the early days of white settlement through to the 1940's and even into the early 1960's. It was used in a range of "working class" occupations - road construction, railway construction, carting goods, rubbish collection etc. and would have been found in cities, country towns and on farms.A wooden and metal tipping dray with a box body and four sides. It has two iron and wooden wheels (with 14 spokes), two wooden shafts and a metal tipping mechanism. The back panel folds down to allow loads to be dumped out. It is painted in green and cream with sign writing on one of the sides and on the front and back panels. It features decorative painted lines and designs in burgundy, cream and light blue on most of the wooden parts. The tipping mechanism is on the front of the dray's left side and consists of a metal pin secured with a metal ring, and a lever.Front of dray - "No. 3" Side of dray - "A. & M. BOURKE / Contractors / LONGWARRY" Back of dray - "G.T. ANDREWS / QUEEN VICTORIA MARKET - Stand C23 / Phone DANDENONG 225"flagstaff hill maritime museum and village, warrnambool, shipwreck coast, tipping dray, dray, tip dray, tip cart, vehicles, horse drawn vehicle, springvale council, jack bourke, muck cart, scotch cart, tumbrel, putt, box body, oswald bourke, sunbury, queen victoria market, melbourne, no. 3