After the 1939 bushfires the Forests Commission placed orders for 130,000 feet (nearly 40 km) of 1½ inch canvas hose in Britain to accompany over 200 new pumps of various types. The Altona workshop became a major centre for fabrication, repair and storage of hose. But lack of standardisation of hose couplings plagued Australian firefighters for decadesUsed to repair canvas hose A rubber patch is placed over the hole in the hose and clamped. It is then heated electrically to melt the rubber patch Canvas hose needs to be washed, dried, rolled and stored properly after it has been used otherwise it will rot. Unrolled hose is notorious for becoming tangled.forests commission victoria (fcv), bushfire, fire pump, fire tanker

A ring called the hoop is used to attach the head to the shell, and the tuning bolts are tightened to tighten the head. The hoop is supported by the lug, and the hoop and lug are attached using a tuning bolt. Long ago, animal skins were used as drum heads, but now drum heads are primarily made of plastic. Basically, when the tension on the head is higher, the tone is higher, and when the tension is lower, the tone is lower.A Cylinder made of metal and wood 37 centimetres diameter and 21 centimetres high. It has a red, black and white wooden trim on the top and bottom and is held together with six metal clamps. There is a drum head on the top and bottom of the cylinder. Ever Play Extra brand is on the top drum head.Lowe musical instruments, drum, sandhurst drummers

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure.This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools.A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl.woodwork tools brace-ratchet

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure.This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools.A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl. The drill bit is jammed and the chuck is rusted.woodworking tool brace-and-bit carpentry

This carpenter's clamp would have been used in confined spaces where a full turn of the brace cannot be achieved. It is fitted with a pawl mechanism - a hinged or pivoted device adapted to fit into a notch of a ratchet wheel to impart forward motion or prevent backward motion. This item would have been used on a rural property in constructing or maintaining infrastructure. This item is an example of a woodworking tool used in the first half of the 20th century prior to the widespread use of power tools. A metal ratchet brace with a wooden handle grip. It has a hinged mechanism device which fits into the notches of the ratchet wheel - a pawl

This ACME portable clothes wringer could be attached to a wash trough or hand washing machine to remove excess water from the washing. It was much less cumbersome that the earlier Mangles used for this purposeMost homes of 20th C in City of Moorabbin would have had one of these ACME wringers . It greatly eased the washday burden of the women. The Exchange Hotel Nepean Highway Cheltenham was a well established meeting place for Moorabbin Shire settlers by 1915A metal clothes wringer with side hand crank and 2 rollers that could be attached by screw clamps to a wash trough or washing machine for removing excess water from washing. The pressure of 2 rollers was controlled by a screw on the top of machine that could be loosened or tightened according to the material being passed through.ACME 14 INCH / on hand crank is list of patents for Great Britain, USA, Aust. NZ, Germany, Belgium, Sweden moorabbin, bentleigh, cheltenham, laundry equipment, washing, washing mangles, washing machines

This large bean slicer was first manufactured in the late 1800's in England and exported to Australia. Due to the transportation costs it was not used in many Domestic kitchens. This slicer would have been in a kitchen of a higher socio/economic family within the Kiewa Valley. In the 1930's the manufacturer traded this slicer as "domestic labour-saving slicers". This was the beginning of new generation of the kitchen "gadget". The introduction of the Asian "gadget" manufacturer from the late 1950's saw English export diminish by the cheaper Asian products.This item has great significance because it demonstrates that even "remote rural" locations, such as the Kiewa Valley in the early 1900s still were able to optain "state of the art" labour saving "kitchen" appliances. It was these English and European goods that were made "to last" which brought the mind set "British is best" This mindset was only altered by periods of Australian economic down turns and the cheap Asian product availabilityThis bean slicer is made from cast iron with a round body housing three rotating blades screwed into a riveted spinning base plate. The whole body of this slicer is green with a "natural coloured" handle. A "G" clamp is part of the main frame to fasten the slicer onto a table/counter top (when in use). On the side of the handle and along the top plate "SPONG & Co Ltd" and opposite "BEAN SLICER" below this "No 633"domestic kitchen time savers, food processors, bean slicers

After the 1939 bushfires the Forests Commission placed orders for 130,000 feet (nearly 40 km) of 1½ inch canvas hose in Britain to accompany over 200 new pumps of various types. The Altona workshop became a major centre for fabrication, repair and storage of hose. But lack of standardisation of hose couplings plagued Australian firefighters for decadesUsed to attach couplers to canvas hose The tool is held in a large clamp and stretches the coupler onto the hose. A tension bar is used to control leverage Canvas hose needs to be washed, dried, rolled and stored properly after it has been used otherwise it will rot. Unrolled hose is notorious for becoming tangled.Warren Brownforests commission victoria (fcv), bushfire, fire pump, fire tanker

These forceps are a type of uterine forceps used for gynaecological procedures. This is one of a collection of items associated with Dr Felix Henry Meyer (1858-1937). Meyer was a very prominent early obstetrician and doctor, playing a part in the establishment of the role of the chair of obstetrics at the University of Melbourne in 1929. He was also a foundation member of the Royal Australian College of Surgeons.Set of metal scissor style forceps. Consists of two blades, joined with a pin, with a small ratchet for clamping below the finger grips/handles. The end of the forceps curves to one side, and each blade of the forceps ends with a hook. When the forceps are closed, the hooks on either blade join together to make a loop.surgery

The State Electricity Commission of Victoria 1921 to 1993 was responsible for electricity generation in Victoria and the operation of three Provincial Tramways. It had a strong safety focus for the time. This first-aid box would have been provided to work places containing first aid equipment and materials. It has been made with interior slots or dividers to hold items. Images of contents of a box that went to auction in Feb. 2025 collected.Demonstrates an SECV First Aid Box.First aid box made from sheet metal, with hinged lid, press locking clamp on the front, with a divided interior or fitting to hold items, painted white on the inside and black on the outside. Has the SEC logo, marked "First Aide" in red letters on a white background and numbered "2787" on the front side.Has SEC logo and number 2787. Has a hand date stamp of "16 Apr 1970" on the inside of the lid, top left hand corner.secv, tramways, first aid, equipment

Hot water sea baths established in 1889 in Bank Street Port Fairy for separate men and women bathing. The bathes were closed in 1916. One bath was taken by Leo Brady when baths were demolished and used in his home until 1939. These items are from this bath.1. Metal bolt used to clamp slabs of marble for bath , from hot water baths. Bolt tapers from top to bottom and round knob on top. 2. Piece of white marble used in the sea baths - roughly triagular in shape. 3.Large piece of marble from the base of a sea bathlocal history, buildings, fittings

This item was used in Dicken's Store. Originally the Pardew Brothers store in Nicholson Street, Orbost, Frank Dicken purchased the shop business. It was a bakery and general store and was known as F.B. Dicken and Son. In 1948 they bought the shop freehold . The store remains today converted into two separate shops. The meat slicer was purchased from Henry Berry and Company a large wholesale grocers and general merchant company, first established in Melbourne in 1859.The Dicken store is a prominent Orbost building. Frank and May Dicken moved to Orbost in 1936 where Frank became manager of Pardew Brothers store in Nicholson Street. In 1945, Frank purchased the business and in 1947, formed a partnership with his son, Selwyn. The store was then called F.B. Dicken and Son. The premises are still retained by the Dicken family although the shop business was sold in 1981. (ref. In Times Gone By - Deborah Hall)A heavy commercial meat slicer which sits on bench. Frame is painted red. The tray moves as the handle turns. The main structure is cast iron. It has a circular steel blade. The chrome output tray is detachable. The movable carriage has a cast aluminium tray with spikes to hold the meat and there is an adjustable clamp to secure the meat.INVICTA Model No 302 21 HENRY BERRY PTY LTD MELBfood-preparation dicken-store meat-slicer

Clamp wooden set of (2) lengths of wood bevelled at one end and standing parallel. Has (2) long screws with handles and predominant thread that fits through wood lengths. Could be 855. 360mm x 55mm x 40mm Pins are each 405mm long. Diameter at handle 30mm for one and 40mm for other.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Used by Wandin T Sebire.A thick curved forged steel scrub slasher - head only. It has two bent steel clamps to attach a handle, one which is small and is attached by a screw, the other large one is attached by two rivets. It was efficient for clearing thin and dense low-lying scrub or bush where an axe would be too clumsy. tools, agricultural equipment, agricultural tools, slashers, gardening tools

Metal cylindrical base to store kerosene. Above this area is a cylindrical glass area for the actual lamp light. Above this is a metal cylindrical cover with perforated holes for venting fumes. A thick metal wire handle is attached to the sides of the lamp. Access to the inside of glass area is via two spring-loaded clamps on either side of the glass area.On glass: Pyrex, Aladdin, Made in Australialamp, light, lantern, kerosene

Framed photograph of the Old Colonists' Association Council. Ed Drury (President) Dr D. Morton Back row left to right: L.McBain, A.J. Symons, J.E. Crocker. R. Buchanan, J. Peebles Front row left to right: C.H. Clamp. Dr S.A. Wilson, E.J. Drury, J.C. Curwen-Walker, W. Titheridged. morton, l.mcbain, a.j. symons, j.e. crocker, r. buchanan, j. peebles, c.h. clamp, dr s.a. wilson, e.j. drury, j.c. curwen-walker, w. titheridge

Early water carrying bladder A number of accidents with these rubber tanks occurred on the fireline, particularly on tracks with steep side grades. The movement of the water sloshing and accumulating on the lower tank wall created an imbalance in the vehicle. The frayed anchor ropes, under strain due to constant rubbing on the high side wall of the vehicle, would snap, and the whole assembly of tank, pump and hose would break away from the vehicle and bounce down through the bushLarge rubber bag which held 80 gallons of water. Developed in the 1960s. It was strapped down in the back tray of Utes and attached to a small fire pump with a control valve. It was filled by a top tube that was clamped closed. It wallowed badly when the vehicle was moving, hence the common name of "Pig". When the bag was full it made driving dangerousDunlopforests commission victoria (fcv), bushfire, fire pump

The Stainsby Braillewriter was utilised by Braille tutors and volunteers as well the blind and visually impaired. Stored in a brown cardboard lockable case and this complete kit consists of a metal Braille writing machine; a long slim rectangular device with carriage and six silver keys and a bell, a metal board to attach Braille writer, a metal hinged Braille paper clamp and an instructional booklet. Henry Stainsby (1859-1925), Supt. of the Birmingham Royal Institution for the Blind, (later General Secretary of the British & Foreign Blind Association) along with Birmingham manufacturer Albert Wayne, introduced their portable brailler writer around 1903. An "improved" version, featuring aluminum parts and a paper clamp allowing accurate interpointing or interlining, was announced in "Outlook for the Blind" as early as 1927 and available generally by 1933 in the RNIB catalog. By 1978, RNIB sold the Improved Stainsby in a number of formats, including a large version available with interlining and inter-pointing board, and a small version with a folding board. Both large and small models came in ordinary and reverse keyed versions. Silver Brailler, rectangular with six silver keys and a bell, with paper board and clip, in cardboard suitcaseM8839 M88 (Brailler) M 8839 (Board) On the outside of the suitcase an address label reads "Braille Library, 31-51 Commercial Road, South Yarra". braille equipment, assistive devices

This item was used by Helena Warren (nee McKeown), a well known photographer and local press correspondent. She lived at Newmerella. The meat mincer was a particularly popular kitchen gadget. By means of the mincer left overs and off cuts could be transformed into shepherd's pie or mince steak. Gadgets like this Universal food chopper are typical of domestic inventions designed to reinforce the principles of thrift and labour-saving. Many of these gadgets were imported from the United States. A cast iron metal hand mincer with a long metal body with an opening at one end, inside which is a circular spiral blade and a screw clamp attachment at the other end. On one side of the mincer is a curved metal handle held in place by a metal nut and a wooden bulb shaped knob at the end. There is a metal circular webbed blade held in place by a metal nut and bolt."Universal No. 2 brand; L.F. & C., New Britain, Conn., U.S.A."mincer chopper food-preparation

This bean slicer was made about the 1920s by the British firm of Spong & Co. This firm was founded by James Osborn Spong in 1856 in London. James Spong invented over 100 labour-saving devices during his lifetime and his firm became well-known for its production of domestic labour-saving and safety devices, especially its grinding machine and its bean slicer. These domestic items were to be found in most households from the 1880s to the 1950s prior to the advent of electrical items that carried out similar labour-saving processes. This bean slicer is of interest as a reminder of the many labour -saving devices that were available to most women early in the 20th century, even those in the rural and more remote areas in AustraliaThis a heavy metal bean slicer with a circular piece with a rounded cut-out at the top for the insertion of the bean and an attached bolted handle with a wooden top. Attached to the circular top is a circular revolving piece with three cutters. Welded on to the top piece is a metal clamp with a large screw for attaching the slicer to a table or bench. The slicer is painted green and has the name of the manufacturer etched on the top piece.Spong & Co Ltd Made In England No 632 Bean Slicervintage bean slicers, spong & co london, vintage household items

Used to lay out Machine work, or to set up pieces on a planer, radial drill, milling machine or boring machine. To set the Scriber the spindle swivels down or up into any position where it is clamped by the knurled nut. There is a fine screw adjustment for the Scriber point (note: this is not original Scriber supplied with this instrument). The base on this Surface Gauge can be set on cylindrical work, using the ‘V’ groove in the base, or by pushing down the two gauge pins. It can be brought square with an edge or T slot. Metal gauge toolgauge, tool, trade, brown and sharp manufacturing company

This is a simple household labour-saving device. The box was fitted to the end of the table and knife polish was sprinkled on the cloth inside. The knife was then placed in the centre of the box and clamped in tightly. The knife was then pulled backwards and forwards several times (three seconds was the suggested time) and the object was then deemed to be polished. All households had cutlery of some sort and many had good silver pieces that were meant to be kept in a sparkling polished condition. This cleaner would have assisted those in a household assigned to the care of the cutlery. These would have included the women of the household, the children or domestic employees. This item is retained as an interesting example of a household labour-saving device from 100 years ago. This is a circular wooden box with an extra piece at one end of the base and a sliding top lid with a wooden knob. The lid lifts up and the inside of the box and the lid is covered with rough cloth. Some of this cloth has rotted away. The top of the lid has a printed label pasted on. This is torn and soiled. ‘Patent The Magic Knife and Fork Cleaner’ ‘I am handy and useful where’r I am used, To clean knives and forks brightly I never refuse, In mansion or cottage to both I do go, So buy me, and try me, my worth you will know.’ household devices, history of warrnambool

See Dean Cat 4575P1. Gold metallic bar. The enamelled badge of Rats of Tobruk Association is mounted at one end. The rear of tie bar has a spring loaded clamp. 2. Gold tie pin with mini chains. This is of circular design with the badge of Rats of Tobruk Association sealed in it behind an acrylic layer. Below the Rats badge are two world spheres. Small chains and two pins come away from rear of badge.tie pins, rats of tobruk

This guillotine is a hand operated machine specifically designed to cut through multiple sheets of paper or card. It has a very heavy and sharp single blade knife mounted between vertical guides or runners. The main users of a machine like this is in by the printing and publication binding industry. Book binding companies use a guillotine to evenly trim the pages of a book after it has been bound. The way the guillotine is used is - paper or card is stacked squarely on the flat table and pushed firmly against the back guide - the handle below the table at the front of the machine is wound around, which brings the back guide forward, pushing the paper stack forward and positioning the centre of the stack below the vertical frame - the upper wheel is wound around, which brings the clamp and firmly in position on top of the paper, to hold it very firmly - the large wheel on the side of the machine is turned around to lower the long sharp blade down onto the pages and cut them through. The sharp edge of the blade is protected somewhat from becoming blunt; a block of wood sits in the table under the stack of paper An early model of a guillotine was patented in 1837 by Thirault, who built a model with a fixed blade. Guillotines similar in principal to this one were patented by Guillaume Massiquot in 1844 and 1852. Over the years many improvements have been made and operation has moved from man power to electricity. Oscar Friedheim Ltd. was the importer and wholesaler of a large range of machinery and equipment for the printing and bookbinding industry. He sold most of his equipment under his own name. On this guillotine or paper cutter he refers to the origin of the guillotine’s manufacture only as “German Manufacrure”. A reference book “Commercial Bookbinding: a description of the processes and the various machines used" by Geo. Stephen, 1910, recommends Oscar Friedheim, amongst others, for the supply of “reliable cutting machines for hand or power”. It also recommends Oscar Friedheim’s for a wide range of other printing machinery and processes. OSCAR FRIEDHEIM LIMITED, LONDON Oscar Friedheim Ltd. was established in 1884 and operated from Ludgate in London. The company was an importer and wholesale supplier in the 1880’s, offering machinery and equipment for the printing and packaging industry for the UK and Ireland. The company became incorporated in 1913. An advertisement of 1913 includes a telegraphic code plus two telephone numbers for Oscar Friedheim Ltd and invites readers to call at the Ludgate, London, showrooms to see the machines working. The company later became Friedheim International Ltd. The book titled “Friedheim, A Century of Service 1884-1984 by Roy Brewer, celebrates Oscar Friedheim’s achievements. Friedheim International currently operates from Hemel Hempstead, on the northern outskirts of London UK. It promotes itself as “… the leading supplier of finishing, converting and packaging machinery to the printing, graphic arts, and highly varied packaging industries in the UK and Ireland. The company’s policy is simple – “employ the best people, work with the best equipment manufacturers in the world, and treat our customers as partners!” The company still sells guillotines. The guillotine is significant for its ability to represent aspects of the printing trade in Warrnambool and in a typical port town circa 1850 to 1910. It represents communication methods and processes used in the time before electrically powered equipment became common in industry.Guillotine (or paper cutter), hand operated. Metal framework with vertical guides, stand and metal mechanical parts including wheels and gears. Table with back guide; handle below front of table winds to move the back guide. A wheel at top of machine winds to adjust pressure of the clamp on the work on the table below it. The cutting blade fits between vertical guides; a timber insert in the table below the blade helps minimise the loss of sharpness of the blade. A handle on the side of the machine turns a large spoked wheel, which rotates a large gear, causing the blade to move up and down. Makers details are on a small oval plaque with embossed maker’s details is screwed onto main body. Maker is O Friedheim, London, and the machine is of German manufacture, circa late 1880’s.Maker’s plaque inscribed "O. FRIEDHEIM / London / German Manufacture"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, printing machinery, printer’s guillotine, paper guillotine, paper cutter machine, oscar friedheim ltd london, friedheim international ltd, bookbinding industry, printing industry

These braces of the type known as ‘Police & Firemen’ were originally worn mostly by men wearing a uniform of some sort – police, firemen, members of the armed forces, postmen, other government officials etc. Later the braces were worn by men, mainly workmen, wanting a durable, good quality item to hold up their trousers. Braces are still worn occasionally by men today, mainly as a fashion item. These braces have no known local provenance but are retained as an example of an item of clothing worn by men 100 years ago. These men’s braces have a loop of long heavy quality elasticized cotton held at the top with a metal clip and with the loop forming two long ends made by a leather clamp near the top. The ends of the two cords have metal clips and two leather straps at each end with eyelets for attachment to buttons. The top of the loop also has two leather straps with eyelets. The cords or loops are adjustable and are woven in red, blue and cream patterns. Police & Firemenvintage men’s wear, history of warrnambool

This meat mincer was born in a period where hand operated mincing and blending machines were only available for household mincing meats and blending ingredients up to the 1960's. Electrical kitchen based whitegoods were rare in areas where the connection to electricity was intermittent or not at all.This kitchen aid is a very significant item in the Kiewa Valley before suitable electrically operated mincers became available and constant reliable electrical connections were installed. The Kiewa Hydro Electricity Scheme provide the stable supply of electricity which made most of the hand operated mincing machines obsolete. However large mincers for bulk supplies were still required eg. kitchens for SEC workers during the 50's and 60's.This heavy industrial type meat mincer(cast iron) has a top "rounded feeder cup" with a mincer screw blade at the bottom. A winder handle rotates the screw like mechanism to mince and express solid pieces of meat at the other end. There is a clamp below the main structure which permits the fastening of the hand driven mincer to a table or solid ledge. The hand grip of the handle is made from wood and fashioned like a clothes peg.On the rounded feeder bowl "MAJOR" and on the winder handle "A POPE PRODUCT"hand operated meat mincers, meat grinders, kitchen utensils

BHS CollectionBlack and white photo of the squared oregon poppet legs , braces, wooden cage framework, guides for the skids and safety clamps of the cages of the Hercules Mine. Beside the photo is a printed description of the photo. In the bottom right corner is a printed description titled Interior of a Mine Battery. Written above it is Kocks Pioneer. Inside View of Kock's Battery. There is no photo. Descriptions and photo are mounted on pale blue paper which is then mounted on brown card and laminated.bendigo, history, long gully history group, the long gully history group - hercules mine & inside view of kock's battery, sheepshead line of reef, kock's pioneer, lincoln mine, lansell's big blue battery, quartz hill, whiffly tables, the chinese

In November 1985 a monument was installed near the corner of Main Road and Pitt Street in Eltham, within the gardens at the front of what is now the Eltham Community and Reception Centre. This monument commemorates Victoria's 150th anniversary and the former location of the Eltham Town Centre, which existed along this section of Main Road, then known as Maria Street. Beneath the site is a time capsule to be opened in the year 2035. A plaque was also erected at this site in October 1987 to commemorate the Shire of Eltham Historical Society's 20th anniversary. The main feature of this monument is a ?tyring disc?, a blacksmith?s implement that was found on this site. This consists of a large iron disc that was used as a platform for fitting iron tyres (like the one shown on top of the platform) to wooden spoked cart wheels. The local blacksmith and wheelwright worked together to assemble the wheel, which was clamped to the platform placed close to the fire. The red hot iron hoop, previously forged to the correct size was lifted with tongs by the blacksmith over the outside of the rim, then hammered down amid flames from the scorching timber. The wheelwright drenched the tyre with cold water as soon as it was in position. A clamp placed on the naff (hub) and screwed down tightly kept the spokes at a constant angle as the tyre cooled. An even pressure from the contracting tyre tightened the joints at each end of the spokes and formed a vice-like grip, which would last for the life of the wheel.Four colour photographs (laser printed on paper); two showing the fitting of the time capsule into the monument and two showing Joh Ebeli during the dedication presentation.eltham, joh ebeli, time capsule